Page 1
Fiber QuickNet Cassette Rear Cable Manager
(3) - FMS1 Slack spools
[FQCRCM]
[OR]
(3) - FMS2 Slack spools
[FQCRCM2]
(3) - #10-32 x 3/8"
Pan head screws
(3) - Spool clamp
brackets
FQCRCM / FQCRCM2
(1) - Strain Relief Bar
(4) - #12-24 x .5"
mounting screws
(4) - M6 x 15mm
mounting screws
Mounting
screws
Strain
relief bar
Mounting Screws
Use (2) of either:
#12-24 x .5", or
M6 x 15mm
#10-32 x 3/8"
pan head
screw
Slack
spool
Spool
clamp
bracket
Strain
relief bar
FQCRCM & FQCRCM2 intended for Panduit 2-Post Racks ONLY.
Not intended for 4-post racks, server cabinets or network cabinets.
Attaching the Strain Relief Bar and Spools
Attach spools, if needed, as shown.
Mount the strain relief bar at the appropriate RU space. Use the
lowest screw hole in the RU space.
Part Number: FQCRCM, FQCRCM2
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS FS008B
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 3
Page 2
© Panduit Corp. 2012
Ta k- Ty
(not included)
Tak-Tys
(not included)
QuickNet SFQ Cassette Installation using a
Standard QuickNet Patch Panel
When used with QuickNet SFQ Cassettes, as shown above, the FQCRCM (shown) can support up to twenty-four MTP* interconnect
cables. The FCQRCM2 can support up to thirty-six**. Only one RU is shown for clarity. Position spools as shown. Route interconnect
cable from the vertical cable manager to the SFQ cassettes as shown. Use Tak-Tys to attach the fiber to the rear manager bars at the
positions indicated in the illustration. Additional ribbon cable slack may be managed in the vertical manager or by making additional
wraps around the slack spools. INSTALLER TIP: For best results, keep the cable transition in the vertical cable manager.
When supporting SFQ cassettes in a QuickNet Angled Patch Panel, interweave the MTP* interconnect cable for
cassettes positioned in the center, as shown.
QuickNet SFQ Cassette Installation using a
QuickNet Angled Patch Panel
INSTALLATION INSTRUCTIONS
Recommended Cable Routing and Spool Orientation
FS008B
* MTP is a registered trademark of US Conec Ltd. ** Spool capacity given for approximately 1 meter breakout length.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 3
Page 3
© Panduit Corp. 2012
For use with Copper Cables
Tak-Tys
(not included)
QuickNet HDQ Series Fiber Optic Cassette Installation
When used with HDQ series cassettes, as shown above, the FQCRCM (shown) can support up to twenty-four MTP* interconnect
cables. The FQCRCM2 can support up to thirty-six**. Only one RU is shown for clarity. Recommended spool positions are shown.
When routing fiber and copper cables in the same RU space, route the fiber separately from the copper cables to avoid
damage to the fiber cables. Only two MTP* interconnect cables (two cassettes) can be supported by the FQCRCM
when used with 36 copper cables (6 cassettes).
INSTALLATION INSTRUCTIONS
FS008B
* MTP is a registered trademark of US Conec Ltd. ** Spool capacity given for approximately 1 meter breakout length.
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 3 of 3
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...