Page 1
Pre-Terminated MTP* Fiber Optic Cassettes
For use with Panduit Pan-Net Opticom Network Cabling System
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
FS025
Panduit Pre-Terminated MTP* Fiber Optic Cassettes are designed to reduce the installation time and effort associated with
connecting a fiber optic network, as well as, to improve overall network reliability through factory tested terminations. These
cassettes are compatible with the Panduit Opticom product line and can be selected with LC, SC, ST or FJ connectors for the
front ports and a MTP* connector for the rear port.
1.0 COMPONENT IDENTIFICATION
FC5-12-10Y, FC6-12-10Y,
FC9-12-10Y, FCSA-12-10,
FCX-12-10Y, FCXO-12-10Y,
FCZ-12-10Y, FCZO-12-10Y
FC5-24-10Y, FC6-24-10Y,
FC9-24-10Y, FCSA-24-10,
FCX-24-10Y, FCXO-24-10Y,
FCZ-24-10Y, FCZA-24-10Y,
FCZO-24-10Y
FC5-12-3SY, FC6-12-3SY,
FC9-12-3SY, FCX-12-3SY,
FCXO-12-3SY
FC5-12-3Y, FC6-12-3Y,
FC9-12-3Y, FCX-12-3Y,
FCXO-12-3Y, FCZ-12-3Y,
FCZO-12-3Y
FC5-12-3S-10SY, FC6-12-3S-10SY,
FC9-12-3S-10SY, FCX-12-3S-10SY,
FCXO-12-3S-10SY
FC6SCMFCMY
FC6SCMFCSY
FC6STMFCM
FC6STMFCS
FC8FJMFCM
FC8FJMFCS
Connector Selection
LC Connector
ST ConnectorSC Connector FJ Connector
2.0 PRECAUTIONS
2.1 It is strongly recommended that safety glasses be worn when handling bare optical fiber. Bare optical fiber is very sharp
and can easily damage the eye.
2.2 Pick up and discard all pieces of bare fiber with sticky tabs. Do not let cut pieces of fiber stick to clothing or drop in the
work area where they are hard to see and can cause injury.
2.3 Laser light is invisible. The invisible light is powerful enough to damage your eyes. Serious damage to the retina of the
eye is possible. Never look into the end of a fiber that may have a laser coupled into it. Should accidental eye exposure
to laser light be suspected, arrange for an eye examination immediately.
2.4 Excessive pulling, twisting, crushing, or bending stresses can damage fiber optic cable. Any damage may result in
decreased optical performance.
2.5 Use dry swab (Panduit part number FSWB-C) to clean the inside of the fiber adapters and the ferrule face of the internal
connectors. Insert and rotate the swab until it contacts the ferrule face. Repeat as needed.
2.6 Should internal connectors require a more thorough cleaning, consult Panduit.
* MTP is a registered trademark of US Conec Ltd.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 2
Page 1 of 2
Page 2
© Panduit Corp. 2011
INSTALLATION INSTRUCTIONS
3.0 Cassette Installation
3.1 Insert the MTP* cassette through the mounting bracket and secure it by locking the plastic rivets.
3.2 Feed one end of the MTP* patch cord though a desired grommet location and connect it to the rear port of the
cassette.
3.3 Route and connect the free end of the MTP* patch cord to the appropriate equipment.
Mounting Bracket
FS025
MTP* Patch Cord
* MTP is a registered trademark of US Conec Ltd.
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 2 of 2
Page 2 of 2
TO EQUIPMENT
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...