Page 1
CM646
STOP
READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE
REMOVING CABINET FROM SKID
Page 2
© Panduit Corp. 2013
Enterprise Network Cabinets
(E6212B1, E6412B2 - Server Configured
INSTRUCTIONS CM646
)
NOTE - Some views in this document may vary
slightly from your actual cabinet configuration.
Tool List:
-22mm wrench
-10mm wrench
-13mm socket wrench
-T30 Torx bit (included with cabinet configuration)
-Wire Cutter
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 2 of 10
Page 3
INSTRUCTIONS CM646
…
…
…
…
…
Table of Contents
General Cabinet Operation Page
Packaging Material Removal……………………………………………...…………… 4
Leveling…………………………..……………………………………………………
Grounding……………………………………………………………………………… 6
Equipment Rail Adjustment……………………………………………………………
Overhead Cable Openings……………………………………………………………
Front & Rear Doors (Removal and Installation) ………………………………………
Side Panels (Removal and Installation) ………………………………………………
5
7
8
9
10
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 10
Page 4
INSTRUCTIONS CM646
Packaging Material Removal
Before removal of packaging material:
Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position. If tip indicator shows improper handling,
inspect cabinet for damage before accepting cabinet.
Before handling cabinet:
Small glide strips are installed at various locations around the cabinet to protect the cabinet’s finish during shipping. These strips are to be
removed prior to handling of cabinet.
REMOVAL INSTRUCTIONS
• Remove all stretchwrap and protective cardboard from outside of cabinet
• Remove [2] Shipping Hold Down Brackets at front and rear of cabinet
• Use
IMPORTANT:
Leveling Legs must be fully retracted before the cabinet is moved into place. Sliding cabinet on leveling legs may
result in damage to the leveling legs. (Leveling Legs ship in retracted position)
[2] people to carefully lift and remove cabinet from pallet
[2] Shipping
Hold Down
Brackets
Note: Doors, Side panels, and other components are removed for clarity.
[4] Lag Screws and Washers
(use 13mm socket wrench)
[6] M6 Torx Screws
(use T30 Torx bit)
Pallet
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 10
Page 5
INSTRUCTIONS CM646
Leveling
• Ensure that [4] Leveling Legs are fully retracted
• Slide Cabinet into final position
• Lower the [4] Leveling Legs until the cabinet weight is fully supported
• Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side
Front-to-Back Cabinet Leveling
[4] Leveling Legs
(use 22mm Wrench)
Side-to-Side Cabinet Leveling
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 10
Page 6
INSTRUCTIONS CM646
Grounding
• Attach Grounding Lug or Grounding Bar at any of the [2] location(s) shown below
• Grounding location is indicated by universal ground symbol
• Use M5 bonding screw
[8] Grounding Lug Locations
(Front and Rear of Beams)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 10
Page 7
INSTRUCTIONS CM646
Equipment Rail Adjustment
• Remove [4] Torx screws and [4] hex nuts per equipment rail
• Move equipment rail to desired positon
• Secure equipment rail to cabinet with[4] Torx screws and [4] hex nuts per rail
• NOTE: Front equipment rails are integral to the cabinet frame and are in a fixed position
[2] Hex Nuts
(use 10mm wrench)
[2] M6 Torx Screws
(use T30 Torx bit)
[2] Hex Nuts
(use 10mm wrench)
[2] M6 Torx Screws
(use T30 Torx bit)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 7 of 10
Page 8
INSTRUCTIONS CM646
Overhead Cable Openings
• Cut [4] tabs with wire cutter to open each cable opening - OPTIONAL
OPTIONAL
[2] 40mm x 131mm Openings
[1.57” x 5.15”]
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 8 of 10
Page 9
INSTRUCTIONS CM646
Front & Rear Doors (Removal and Installation)
• Open Door(s) to approximately 90º
• Lift Door(s) up and pull away from cabinet frame
• REVERSE STEPS to install Front & Rear Doors
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 10
Page 10
INSTRUCTIONS CM646
Side Panels (Removal and Installation)
• Unlock side panel
• Pull top of side panel away from cabinet frame
• Lift bottom tabs out of cabinet frame
• REVERSE STEPS to install Side Panel
Side Panel Tabs
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 10 of 10
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...