Panduit Inlet/Exhaust Duct for Cisco
7018 Switch
PART NUMBERS: DIEBCC7018B
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
INLET DUCT COMPONENTS
CM669
Side Inlet Upper
(12V360BU)
Inlet Duct Top Seal Plate
(12V360BN)
Side Inlet Lower
(12V360BV)
Inlet Stiffener
Bracket
(12V360BW)
Rear Inside Intake
Upper
(12V360BY)
Front-To-Back Bracket
UR&LL
(12V360BJ)
Rear Inside Intake
Lower
(12V360BZ)
Front-To-Back Bracket
LR
(12V360BM)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Bottom Duct Rear Plate
(12V360BL)
Page 2 of 32
Bottom Intake Duct
(12V360BK)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
EXHAUST DUCT COMPONENTS
CM669
Side Exhaust Upper
(12V360AE)
Front-To-Back
Bracket UL
(12V360CF)
Side Exhaust Lower
(12V360AJ)
(2) Exhaust Rear
Vertical Post
Cover
(12V360CE)
Exhaust Top Seal Plate
(12V360BP)
(2) Exhaust Rear
Exhaust Rear
Seal Plate
(12V360BR)
Bracket
(12V360CA)
Exhaust Rear
Lower Seal Plate
(12V360BT)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Exhaust Bottom Seal
Plate
(12V360BS)
Page 3 of 32
(2) Front-To-Back
Bracket UR&LL
(12V360BJ)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 1
With the front equipment rails in the full forward position, front to back equipment rails must be set at
658mm (25.9") apart.
Equipment Rails
Must Be 658mm
(25.9") Apart.
CM669
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 2
Insert (5) cage nuts as shown in images A, B and C.
CM669
Image A
Front Left
Equipment Rail
Image B
Cage Nut
RU’s 1 & 4
Cage Nut
Image C
Front Right
Equipment Rail
Rear Left
Equipment Rail
RU 1
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 32
Cage Nut
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Installing Inlet Duct
CM669
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 3
Slide Bottom Intake Duct (12V360BK) into position in RU’s 1-4 and fasten with (4) 12-24 screws.
CM669
(4) 12-24 Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
Bottom Intake
Duct
(12V360BK)
Page 7 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 4
Attach Front-To-Back Bracket LR (12V360BM) to the (3) studs on the inside of 12V360BK (making
sure that the long plate on 12V360BM is perfectly level) and secure with (3) M5 nuts. Then secure
12V360BM to the front support rail with (1) M5 button head screw.
Front-To-Back LR
(12V360BM)
(Must be Level)
CM669
Front-To-Back LR
(12V360BM)
(Must be Level)
M5 Button
Head Screw
For Technical Support: www.panduit.com/resources/install_maintain.asp
Bottom Intake Duct
(12V360BK)
Front Support Rail
VIEW FROM REAR
Page 8 of 32
(3) M5 Nuts
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
STEP 5
Attach Bottom Duct Rear Plate (12V360BL) to the (2) studs on the back of Bottom Intake Duct (12V360BK).
(A) If 7018 switch is in, raise Bottom Duct Rear Plate (12V360BL) up to meet the bottom of the switch and
secure with (2) M5 nuts.
(B) If 7018 switch will be installed later, leave (2) M5 nuts loose until switch is in. When switch is in, perform
step (A).
Bottom Intake Duct
(12V360BK)
View From Rear
(3) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 32
Bottom Duct Rear
Plate
(12V360BL)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
STEP 6
Attach Front-To-Back Bracket UR&LL(12V360BJ) to the rear side of the front support rail of the cabinet at RU’s
30 and 31 with (2) M5 button head screws and to the front side of the rear support rail at RU’s 30 and 31 with (2)
M5 hex head screws. The long plate facing out MUST BE COMPLETELY LEVEL before tightening screws.
THIS SURFACE MUST BE
COMPLETELY LEVEL
RU’s 30 & 31
Front Side of
Rear Support Rail
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 10 of 32
(2) M5 Hex Head Screws
(Button Head Screws Used
with Front Rail.)
Front-To-Back
Bracket UR&LL
(12V360BJ)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 7
From the inside of the cabinet slide the stud on Rear Inside Intake Upper (12V360BY) into Front-To-Back
Bracket UR&LL (12V360BJ). Secure into place with (1) M5 nut.
CM669
M5 Nut
Front-To-Back
Bracket UR&LL
(12V360BJ)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 11 of 32
Rear Inside Intake
Upper
(12V360BY)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 8
Slide the fold on the top of Rear Inside Intake Lower (12V360BZ) into the fold on the bottom of Rear
Inside Intake Upper(12V360BY). Secure the bottom of 12V360BZ to the equipment rail at RU 1 with
(1) 12-24 screw.
Rear Inside Intake
Upper
(12V360BY)
CM669
Rear Inside Intake
Lower
RU 1
(12V360BZ)
12-24 Screw
NOTE: Support post removed from view for clarity.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 12 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
STEP 9
Slide Side Inlet Upper (12V360BU) along the top of Front-To-Back Bracket UR&LL (12V360BJ) so that the stud
on Front-To-Back Bracket UR&LL (12V360BJ) fits into the slot on Side Inlet Upper (12V360BU) and that the (2)
studs on Rear Inside Intake Upper (12V360BY) fit into the (2) holes in Side Inlet Upper (12V360BU). Secure Side
Inlet Upper (12V360BU) to Front-To-Back Bracket UR&LL (12V360BJ) with (1) M5 nut and to Rear Inside
Intake Upper (12V360BY) with (2) M5 nuts.
Front-To-Back Bracket
UR&LL
(12V360BJ)
M5 Nut
Rear Inside Intake
Upper
(12V360BY)
Side Inlet Upper
(12V360BU)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 13 of 32
(2) M5
Nuts
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
STEP 10a
Slide the fold on the top of Side Inlet Lower (12V360BV) into the fold on the bottom of Side Inlet Upper
(12V360BU).When sliding Side Inlet Lower (12V360BV) into place make sure that the bottom of Side Inlet
Lower (12V360BV) passes under Rear Inside Intake Lower (12V360BZ) and over Front-To-Back Bracket LR
(12V360BM) so that the slot in Side Inlet Lower (12V360BV) slides over the stud on Front-To-Back Bracket LR
(12V360BM).
Side Inlet Upper
(12V360BU)
Side Inlet Lower
(12V360BV)
Rear Inside Intake
Lower
(12V360BZ)
M5 Nut
NOTE:
Side Inlet Lower (12V360BV) must slide
under Rear Inside Intake Lower
Front-To-Back
Bracket LR
(12V360BZ) and over Rear Inside Intake
Lower (12V360BZ).
(12V360BM)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 14 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 10b
When in place the (2) studs on Rear Inside Intake Lower (12V360BZ) should pass through the (2)
holes in Side Inlet Lower (12V360BV). Secure Side Inlet Lower (12V360BV) into place with (2) M5
nuts.
CM669
Side Inlet Lower
(12V360BV)
(2) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 15 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 11
Slide the fold in Inlet Stiffener Bracket (12V360BW) over the edge of Side Inlet Upper
(12V360BU). Secure to the front support rail at Ru’s 16 and 17 with (2) M5 button head
screws.
RU’s 16 & 17
CM669
Side Inlet Upper
(12V360BU)
(2) M5 Button
Head Screw
Front Support
Rail
Inlet Stiffener Bracket
(12V360BW)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 16 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 12
Slide the (3) studs on Inlet Duct Stiffener Bracket (12V360BN) into Front-To-Back Bracket UR&LL
(12V360BJ) and secure into place with (3) M5 nuts.
(A) If switch is installed make sure plate "seals" down onto top of 7018 switch before tightening nuts.
(B) If no 7018 switch, leave nuts loose. After switch is installed, perform step (A).
CM669
Inlet Duct Top Seal
Plate
(12V360BN)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Front-To-Back Bracket
UR&LL
(12V360BJ)
(3) M5 Nuts
Page 17 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Installing Exhaust Duct
CM669
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 18 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 13
Attach Front-To-Back Bracket UR&LL (12V360BJ) to the rear side of the front support rail of the
cabinet at RU’s 3 and 4 with (2) M5 button head screws and to the front side of the rear support rail at
RU’s 3 and 4 with (2) M5 hex head screws. The long plate facing out MUST BE COMPLETELY
LEVEL before tightening screws.
THIS SURFACE MUST BE
COMPLETELY LEVEL
CM669
Front-To-Back
Bracket UR&LL
(12V360BJ)
(2) M5 Hex Head Screws
(Button Head Screws Used
with Front Rail.)
Rear Support Post
RU’s 3 & 4
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 19 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 14
Insert stud on Exhaust Rear Lower Seal Plate (12V360BT) into the hole closest to the rear of the cabinet in
Front-To-Back Bracket UR&LL (12V360BJ). Secure into place with (1) M5 nut.
CM669
Exhaust Rear Lower
Seal Plate
(12V360BT)
Front-To-Back
Bracket UR&LL
(12V360BJ)
M5 Nut
SUPPORT RAIL NOT SHOWN FOR CLARITY
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 20 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 15
Attach supplied flap seal to Exhaust Bottom Seal Plate (12V360BS) (As shown in image below).
Flap Seal
CM669
Exhaust Bottom Seal Plate
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 21 of 32
(12V360BS)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM669
STEP 16
Slide the (3) studs on Exhaust Bottom Seal Plate (12V360BS) into Front-To-Back Bracket UR&LL (12V360BJ)
and secure into place with (3) M5 nuts.
(A) If switch is installed make sure plate "seals" down onto top of 7018 switch before tightening nuts.
(B) If no 7018 switch, leave nuts loose. After switch is installed, perform step (A).
Exhaust Bottom Seal Plate
(12V360BS)
SUPPORT RAIL NOT SHOWN FOR CLARITY
Front-To-Back
Bracket
UR&LL
(12V360BJ)
(3) M5 Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 22 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 17
Attach Front-To-Back Bracket UL (12V360CF) to the rear side of the front support rail of the cabinet
at RU’s 30 and 31 with (2) M5 button head screws and to the front side of the rear support rail at RU’s
30 and 31 with (2) M5 hex head screws. The long plate facing out MUST BE COMPLETELY
LEVEL before tightening screws.
THIS SURFACE MUST BE
COMPLETELY LEVEL
CM669
Front-To-Back
Bracket UL
(12V360CF)
(2) M5 Hex Head Screws
(Button Head Screws Used
with Front Rail.)
RU’s 30 & 31
Rear Support Rail
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 23 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 18
Attach (1) Exhaust Rear Vertical Post Cover (12V360CE) to rear support rail with (3) M5 button
head screws so that the bottom is flush against Front-To-Back Bracket UR&LL (12V360BJ). Attach a
second Exhaust Rear Vertical Post Cover (12V360CE) to front support rail with (3) M5 button head
screws so that the bottom is flush with previous Exhaust Rear Vertical Post Cover (12V360CE).
(2) Exhaust Rear Vertical Post Cover
(12V360CE)
Rear Support Rail
(6) M5 Button
Head Screws
CM669
View of Exhaust Rear Vertical
Post Cover (12V360CE)
Attached to Cabinet.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 24 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 19
Attach (1) Exhaust Rear Bracket (12V360CA) to front support rail with (2) M5 button head screws so
that the bottom is flush against Front-To-Back Bracket UR&LL (12V360BJ). Attach a second
Exhaust Rear Bracket (12V360CA) to front support rail with (2) M5 button head screws so that the
bottom is flush with previous Exhaust Rear Bracket (12V360CA).
NOTE: Rear Support Rail Not Shown in View for Clarity.
(4) M5 Button
Head Screws
(2) Exhaust Rear Bracket
(12V360CA)
View of Exhaust Rear
Bracket (12V360CA)
Attached to Cabinet.
CM669
Front Support Rail
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 25 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 20
Attach bulb seal along the edge of the (2) Exhaust Rear Bracket (12V360CA) brackets.
Exhaust Rear
Bracket
(12V360CA)
CM669
Bulb Seal
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 26 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 21a
Slide Side Exhaust Upper (12V360AE) along the top of Front-To-Back Bracket UL (12V360CF) until
the (3) studs on the back of Side Exhaust Upper (12V360AE) pass through the openings in Exhaust
Rear Bracket (12V360CA). Secure Side Exhaust Upper (12V360AE) to Front-To-Back Bracket UL
(12V360CF) with (1) M5 nut. Attach Side Exhaust Upper (12V360AE) to the front support rail with (3)
M5 button head screws.
Front-To-Back
Bracket UL
(12V360CF)
Side Exhaust Upper
(12V360AE)
(3) M5 Button
Head Screws
Rear Support Rail
CM669
M5 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 27 of 32
Exhaust Rear
Bracket
(12V360CA)
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 21b
Secure Side Exhaust Upper (12V360AE) to Exhaust Rear Bracket (12V360CA) with (3) M5 nuts.
Side Exhaust Upper
(12V360AE)
CM669
Exhaust Rear
Bracket
(12V360CA)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 28 of 32
(3) M5 Nuts
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 22a
Slide Side Exhaust Lower (12V360AJ) along the top of Front-To-Back Bracket UR&LL
(12V360BJ), so that the folds in Side Exhaust Lower (12V360AJ) and Side Exhaust Upper
(12V360AE) interlock, until the (3) studs on the back of Side Exhaust Lower (12V360AJ) pass
through the openings in Exhaust Rear Bracket (12V360CA). Attach Side Exhaust Lower (12V360AJ)
to the front support rail with (3) M5 button head screws.
(3) M5 Button
Head Screws
Side Exhaust
Lower
(12V360AJ)
CM669
Rear Support Rail
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 29 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 22b
Secure Side Exhaust Lower (12V360AJ) to Exhaust Rear Bracket (12V360CA) with (3) M5 nuts.
Side Exhaust
Lower
(12V360AJ)
CM669
Exhaust Rear Bracket
(3) M5 Nuts
(12V360CA)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 30 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 23
Slide the stud on Exhaust Rear Seal Plate (12V360BR) into the opening in Front-To-Back Bracket UL
(12V360CF) at the rear of the cabinet and secure into place with (1) M5 nut.
CM669
Exhaust Rear Seal Plate
(12V360BR)
Front-To-Back Bracket UL
(12V360CF)
M5 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 31 of 32
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 24
Slide the (3) studs on Exhaust Top Seal Plate (12V360BP) into Front-To-Back Bracket UL (12V360CF) and
secure into place with (3) M5 nuts.
(A) If switch is installed make sure plate "seals" down onto top of 7018 switch before tightening nuts.
(B) If no 7018 switch, leave nuts loose. After switch is installed, perform step (A).
Front-To-Back Bracket UL
(12V360CF)
Exhaust Top Seal Plate
(12V360BP)
CM669
(3) M5 Nuts
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 32 of 32
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...