Panduit CUEORF03DPB1 Installation Manual

Download

Page 1

900mm Drop Away Panel Ceiling System

for Universal Aisle Containment

Part Number(s) : CUEORF03DP** & CUCGF03DP**

INSTALLATION INSTRUCTIONS

900mm Drop Away Panel

Ceiling System

V00029PA

Tool List:

• 7mm Socket Wrench

• Scissors

For Technical Support: www.panduit.com/resources/install_maintain.asp

Net-Contain Universal

Aisle Containment Framing

Not Included

(See Installation Instruction V00029JB)

Page 1 of 11

Page 2

INSTALLATION INSTRUCTIONS

Component Guide for 900mm Drop Away Panel Ceiling System

900mm End of Row Kit

CUEORF03DP**

(1) 900mm End of Row Beam

(1) 900mm Adjustable End of Row Beam

(1) Slider Plate Assembly

(1) Hardware Kit

V00029PA

900mm Ceiling Grid

CUCGF03DP**

(1) 900mm Aisle Beam Assembly

(1) 2x3 Drop Away Panel

(2) Progression Plate

(1) Hardware Kit

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 11

Page 3

INSTALLATION INSTRUCTIONS

V00029PA

Installation of the End of Row Beam

• Install the End of Row Beam onto one end of the Pod. This is where the ceiling grid installation will begin.

• The Adjustable End of Row Beam and Slider Plate Assembly will be installed onto the opposite end of Pod. (see page 8)

End of Row Beam

M5x0.8 x 10mm

Hex Head Screw

5 places

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 11

Page 4

INSTALLATION INSTRUCTIONS

Installation of the Progression Plates

• Install the Progression Plates onto the shelf in the orientation shown.

• Butt the Progression Plates up against the End of Row Beam and tighten down.

V00029PA

M5x0.8 x 10mm Hex Head Screw 2 places per side

Butt the Progression Plates up

against the End of Row Beam

before tightening screws.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 11

Page 5

INSTALLATION INSTRUCTIONS

Installation of the Aisle Beam

• Install each Aisle Beam making sure to butt the Aisle Beam up to the Progression Plates.

M5x0.8 x 10mm Hex Head Screw 2 places per side

Aisle Beam

V00029PA

Butt the Aisle Beam up against

the Progression Plates

before tightening screws.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 5 of 11

Page 6

INSTALLATION INSTRUCTIONS

V00029PA

Install all of the remaining Progression Plates and Aisle Beams

• Install remaining Progression Plates and Aisle Beams butting the Aisle Beams and Progressio n Plates up to each other.

NOTE: Leave last space open. Refer to page 8 for Instructions on last Pod opening.

Refer to page 8 for

Instructions on

last Pod opening.

Butt the Progression Plates and

the Aisle Beams

before tightening screws.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 11

Page 7

INSTALLATION INSTRUCTIONS

Installation of the Panels

• Install all the Panels by pushing down from the top of Pod.

NOTE: Leave last space open. Refer to page 8 for Instructions on last Pod opening.

V00029PA

Panels snap down below Aisle Beam

anges.CenterPanelsingridopenings

Refer to page 8 for Instructions on

last Pod opening.

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 7 of 11

Page 8

INSTALLATION INSTRUCTIONS

Installation of the the Adjustable End of Row Beam

• Install the Adjustable End of Row Beam onto the opposite end of Pod.

Adjustable End of Row Beam

V00029PA

M5x0.8 x 10mm

Hex Head Screw

5 places

Opposite End

of Pod.

Installation of the last Panel and Slider Plate Assembly

Option 1. Last opening is between 23.3” and 27.2”

• Install Slider Plate Assembly using full Panel.

M5x0.8 x 10mm

Hex Head Screw

2 places

Slider Plate Assembly

Figure 1

Full Panel - 23.3” to 27.2”

Cut Panel - less than 23.3”

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 8 of 11

Page 9

INSTALLATION INSTRUCTIONS

V00029PA

Slide the Slider Plate Assembly over to

support the (2) full Panels, then tighten

the (2) M5x0.8 x 10mm Hex Head Screw

Full Panel

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 9 of 11

Page 10

Option 2. Last opening is less than 23.7”

• Install Slider Plate Assembly using cut Panel.

INSTALLATION INSTRUCTIONS

V00029PA

Measure distance from Figure 1

andCutPanelsto1/2”less

than measurement

CutPanel

Slide the Slider Plate Assembly over to

support the cut Panel, then tighten the (2) M5x0.8 x 10mm Hex Head Screws

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 10 of 11

Page 11

INSTALLATION INSTRUCTIONS

V00029PA

Removal and Re-installation of Panels

• If access permits, Panels can be slide in and out from the side of Pod at the top.

• Lift Panel above Progression Plate stop to start. While sliding out, continue to lift Panel above stop to prevent scratching.

Panels can be slide in and out from the side of Pod at the top.

Progession

Plate stop

Panels can also be removed from inside of Pod.

Small screwdriver - Slide along Aisle Beam to release lip of Panel from Aisle Beam track.

View from underside of Pod

View from top of Pod

To re-install panels: Small hex key - Slide along Aisle Beam while pulling downward to re-engage lip of Panel back into the Aisle Beam track.

View from underside of Pod

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

www.panduit.com

Page 11 of 11

View from top of Pod

E-mail:

techsupport@panduit.com

Phone:

866-405-6654