Page 1
PA25383A01
CRIMPING HEADS USED WITH THE CT-2500, CT-2500/E; or
CT-2500/L, CT-2500/LE TOOLS
© Panduit Corp. 2019
CT-2525CH
Crimping head for installing the following Panduit products:
CT-2550CH
Crimping head for installing the following Panduit products:
Reduced crimp effort advantage for #12 – #10 AWG (4,0 – 6,0mm2) terminations.
CT-2570CH
Crimping head for installing most of the following Panduit products:
CT-2525CH, CT-2550CH
Rev. 07 1-2019
and CT-2570CH
CT-2525CH CT-2550CH CT-2570CH
#26 – #22 AWG (0,14 – 0,5 mm2) insulated terminals and splices,
#22 – #10 AWG (0,5 – 6,0 mm
and specific #22 – #14 AWG (0,5 – 2,5 mm
2
) fully insulated disconnects, insulated parallel splices;
2
) barrel insulated disconnects.
#22 – #10 AWG (0,5 – 6,0 mm2) insulated terminals and splices;
and specific insulated disconnects.
#22 – #10 AWG (0,5 – 6,0 mm2) non-insulated terminals, disconnects; and specific
non-insulated splices.
CRIMPING HEAD INSTALLATION
(See Page 2)
Monthly Maintenance
1. Thoroughly clean all surfaces.
2. Oil the locating pins.
NOTE: In the interest of higher quality an d value, we are constantly improving and updating our
products. Consequently, pictures in this manual may sometimes vary from the product
enclosed.
E-mail:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
Page: 1 of 2
www.panduit.com
Technical Support:
1-800-777-3300
Panduit Europe
EMEA Service Center
Almelo, Netherlands
Tel: +31-546-580-452
Fax: +31-546-580-441
Page 2
© Panduit Corp. 2019
CT-2525CH, CT-2550CH
and CT-2570CH
1. Rotate crimping head adapter fully -clockwise (see Figure 1).
2. Press retract slide to lower piston
completely.
3. Pull out the pins for mounting a
different crimping head on the
adapter.
4. Before installing a d ifferent crimping
open position. Lock the head with
the locating pins (see Figure 2),
paying attention that the pins are
The crimping cycle is terminated
reached, which is indicated by the
CRIMP POCKET
ENGLISH GO / NO GO GAGE MEMBERS
METRIC GO / NO GO GAGE MEMBERS
AWG / mm2
“G” Dia. (GO)
“NG” Dia. (NO GO)
“G” Dia. (GO)
“NG” Dia. (NO GO)
Pocket “A”
.0835”
.091”
2,12 mm
2,31 mm
22 – 14 / 0,5 – 2,5
.0765”
.084”
1,94 mm
2,13 mm
12 – 10 / 4,0 – 6,0
.1005”
.108”
2,55 mm
2,74 mm
CRIMP POCKET
ENGLISH GO / NO GO GAGE MEMBERS
METRIC GO / NO GO GAGE MEMBERS
AWG / mm2
“G” Dia. (GO)
“NG” Dia. (NO GO)
“G” Dia. (GO)
“NG” Dia. (NO GO)
22 – 14 / 0,5 – 2,5
.1015”
.108”
2,57 mm
2,74 mm
12 – 10 / 4,0 – 6,0
.1475”
.154”
3,74 mm
3,91 mm
CRIMP POCKET
ENGLISH GO / NO GO GAGE MEMBERS
METRIC GO / NO GO GAGE MEMBERS
AWG / mm2
“G” Dia. (GO)
“NG” Dia. (NO GO)
“G” Dia. (GO)
“NG” Dia. (NO GO)
22 – 18 / 0,5 – 1,5
.0515”
.060”
1,31 mm
1,53 mm
16 – 14 / 1,5 – 2,5
.0735”
.082”
1,87 mm
2,09 mm
12 – 10 / 4,0 – 6,0
.0995”
.108”
2,53 mm
2,75 mm
INSTALLATION INSTRUCTIONS
CRIMPING HEAD INSTALLATION
head, slide the crimp di es to the full
locked securely before starting.
5.
when the dies are com pletely closed
and the maximum crimping force is
auto retraction of the piston.
Refer to the CT-2500, CT-2500/E
(PA25346A01); or CT-2500/L,
CT-2500/LE (PA28113A01) Operation
Manual for complete tool and crimping
head instructions.
ATTENTION: The crimping process can be interrupted at any time by releasing the trigger.
After having terminated the cri m ping process and prior to changing the heads, remove battery
to avoid unintended starts.
DIE CLOSURE GO / NO GO GAGE MEMBERS – CT-2525CH
DIE CLOSURE GO / NO GO GAGE MEMBERS – CT-2550CH
DIE CLOSURE GO / NO GO GAGE MEMBERS – CT-2570CH
Page: 2 of 2
Loading...