Page 1
INSTALLATION INSTRUCTIONS
©Panduit Corp. 2001
1. PART NUMBERS
Horizontal Cable Management Racks
WMP1 WMPH2H CMR19X47
WMPF1 WMPHF2H CMR19X84
WMPSH WMPH2, WMPH223 CMR23X84
WMPFSH WMPHF2, WMPHF223 CMR19X26
WMPLS WMPH3H
WMPLFS WMPHF3H
WMPS, WMPS23 WMPH3, WMPH323
WMPFS, WMPFS23 WMPHF3, WMPHF323
2. RACK INSTALLATION
2.1 ASSEMBLE RACK
2.1.1 Install top angle to upright channels. Finger tighten only.
Cable Management Horizontal
Panels and Racks
Printed in U.S.A.
2.1.2 Install the base angles to the vertical upright channels. Finger
tighten only.
2.1.3 Stand rack upright. Square the upright channels with the base
using a carpenter square. Completely tighten all bolts.
See the diagram below for dimensions needed to locate the rack
and the vertical cable management.
2.2 MOUNT RACK T O FL OOR
2.2.1 Securely mount the rack to the floor using the appropriate
hardware based on the f loor construction (conc rete, r aised floor , or
wood).
3. HORIZONTAL CABLE
MANAGEMENT INSTALLATION
3.1 ATTACH HORIZONTAL CABLE MANAGEMENT PANEL
3.2 Use four (4) 1/4”- 20 x 1/2” screws to fasten the horizontal
LOCATION GUIDE
Dimensions in () parenthesis are for 6” Vertical Cable Management
12.5
1.25
1.25
3.00
20.25 = 19” rack
24.25 = 23” rack
16.00 = 19” rack
20.00 = 23” rack
2.12
9.25
(11.06)
20.25 = 19” rack
24.25 = 23” rack
16.00 = 19” rack
20.00 = 23” rack
For Technical Assistance call: 888-506-5400, Ext. 6914
4.57
3.56
3.69
2.12
PN220A
Page 1 of 3
Page 2
Page 2 of 3
management between the racks.
BREAK OFF FINGERS OF
VERTICAL MANAGEMENT
WHERE IT MEETS THE
HORIZONTAL MANAGEMENT
INSTALLATION INSTRUCTIONS
3.3 VERTICAL TO HORIZONTAL
JUNCTION
3.3.1 Break the fingers off of the vertical
panel where it meets the horizontal
panel.
BACK
THREAD CABLES THROUGH
THE STRAIN RELEIF BRACKET
SNAP IN WIRE RETAINER (WR5)
IS INCLUDED IN THE VERTICAL
PANEL KITS.
FRONT
#12 - 24 X 1/2” SCREWS
CABLE CAPACITY CHART
Part Number
WMP1 72 72 36 36 72 72
WMPF1 72 36 72
WMPFS,
WMPFS23
WMPH2,
WMPH223
WMPHF2,
WMPHF223
WMPHF3,
WMPHF23
WMPH3,
WMPH323
WMPLFS 24 12 24
WMPLS 24 24 12 12 24 24
WMPS,
WMPS23
3.3.2 Route the cables through the strain
relief brackets as shown.
3.3.3 Place snap in wir e retainer between
duct fingers.
3.3.4 Turn retainer 90°.
3.3.5 Push retainer to end of fingers until it
snaps in place.
4. DATA-PATCH 110
STYLE PATCH PANEL
ScTP or CAT 6
UTP Cable
.187” Dia.
Front Back
36 18 36
72 72 36 36 72 72
72 36 72
192 96 480
192 192 96 96 480 480
36 36 18 18 36 36
Cable
.25” Dia.
Front Back
Fiber
3mm
Front Back
NOTE: DUCT BASED ON 40% FILL CAPACITY
For Technical Assistance call: 888-506-5400, Ext. 6914
PN220A
Page 3
TERMINATION
INSTALLATION INSTRUCTIONS
WMPH2
BLOCK 24
BLOCK 23
SLOT 23
WMPH2
BLOCK 3
BLOCK 2
BLOCK 1
SLOT 1
4.1 When mounting two 24 port rows of patch panels concurrently or a single 32, 48, or 64
port panel:
4.1.1 To terminate the first block, run the cable from the first Cab le Management Panel slot directly to the first
block.
4.1.2 Repeat steps 5.1.1 and 5.1.2 with the adjacent columns unti l each block is terminated. (Due to space
constraints, the cable for blocks 1 and 2 should be double stacked in slot 1).
WMPH2
SLOT 23
BLOCK 24
BLOCK 23
BLOCK 48
BLOCK 47
SLOT 1
BLOCK 2
BLOCK 1
BLOCK 26
BLOCK 25
SLOT 23
WMPH2
BLOCK 27
SLOT 1
4.2 When mounting two 48 port rows of patch panels concurrently or a single 96 port panel:
4.2.1 To terminate the first block (BLOCK 25), run the cable from the first Cable Management Panel slot
directly to block 25.
4.2.2 To terminate the second block (BLOCK 27), run the cable from the third cable management panel slot
to block 27.
4.2.3 Repeat steps 4.2.1 to 4.2.2 f or the remaining blocks in the bottom row, remembering to leave an empty
slot between each terminated bloc k.
4.2.4 To terminate the second, third, and forth row start at block 26 from sl ot 1. Continue with the rest of the
blocks but run the cable through the even numbered slots.
4.3 Refer to the D AT A-PA TCH 110 Styl e P atc h P anel In struction shee t fo r Punc h Down Block
Termination.
PN220A
Page 3 of 3
NETWORK CONN ECTIVITY GROUP
10500 West 167th Street
Orland Park, IL 60467
Phone: 888-506-5400, Ext. 6914
FAX: 708-444-6993
WORLDWIDE SUBSIDIARIES AND SALES OFFICES
Email:info@panduit.com
Web site: www.panduit.com/ncg
Loading...