CM661A
STOP
READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE
REMOVING CABINET FROM CARTON
© Panduit Corp. 2013
Enterprise Cabinets
(E6212B1FP, E6212B1FP5, E6412B2FP, E6412B2FP5 - Server Configured
INSTRUCTIONS CM661A
NOTE - Some views in this document may vary
slightly from your actual cabinet configuration.
)
Tool List:
-27mm wrench
-22mm wrench
-10mm wrench
-Phillips Screwdriver
-T30 Torx bit (included with cabinet configuration)
-Wire Cutter (optional)
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 2 of 12
INSTRUCTIONS CM661A
…
…
…
…
…
…
Table of Contents
Cabinet Operation Page
Frame Assembly……………………………………………...………………..………
Leveling Leg and Caster Installation…………………………..………………………
Leveling…………………………..……………………………………………………
Equipment Rail Adjustment…………………………………………………………… 7
Top Cap Installation and Overhead Cable Openings…………………………………
Grounding……………………………………………………………………………… 9
Door & Side Panel Bumper Installation………………………………………………
Front & Rear Doors (Installation and Removal) ………………………………………
Side Panels (Installation and Removal) ………………………………………………
4
5
6
8
10
11
12
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 12
INSTRUCTIONS CM661A
Frame Assembly
• Use [24] M6 Torx Screws to assemble [4] Cabinet Posts
to Upper and Lower Cabinet Frame Members
ENSURE that leveling
leg nuts of rear posts
are at bottom of cabinet
[24] M6 Torx Screws
(use T30 Torx bit)
Left Front Post
(with integrated
cage nut cutouts)
Upper
Cabinet
Frame
Member
Left
Rear
Post
Right
Rear
Post
Left Front Post
(note diamond cutout)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Right Front Post
(with integrated
cage nut cutouts)
Page 4 of 12
ASSEMBLED FRAME
Lower
Cabinet
Frame
Member
INSTRUCTIONS CM661A
Leveling Leg and Caster Installation
• Install [4] Leveling Legs into cabinet frame to fully retracted position
• Install [4] Caster Assemblies with [4] Hex Nuts per caster
[4] Caster Assemblies
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 12
[4] Hex Nuts per Caster
(use 10mm Wrench)
[4] Leveling Legs
(use 22mm Wrench)
INSTRUCTIONS CM661A
Leveling
• Ensure that [4] Leveling Legs are fully retracted
• Roll Cabinet into final position
• Lower the [4] Leveling Legs until the cabinet weight is fully supported
• Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side
Front-to-Back Cabinet Leveling
[4] Leveling Legs
(use 22mm Wrench)
Side-to-Side Cabinet Leveling
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 12
INSTRUCTIONS CM661A
Equipment Rail Installation
• Move equipment rail to desired positon
• Secure equipment rail to cabinet with[4] Torx screws and [4] hex nuts per rail
• NOTE: Front equipment rails are integral to the cabinet frame and are in a fixed position
• NOTE: Diamond cutouts on cabinet frame indicate mounting holes to allow for 742mm industry standard
equipment rail spacing. Mount equipment rails to mounting holes immediately in front of diamond cutouts.
[2] Hex Nuts
(use 10mm wrench)
Diamond Cutout
[2] M6 Torx Screws
(use T30 Torx bit)
[2] Hex Nuts
(use 10mm wrench)
Diamond Cutout
For Technical Support: www.panduit.com/resources/install_maintain.asp
[2] M6 Torx Screws
(use T30 Torx bit)
Page 7 of 12
INSTRUCTIONS CM661A
Top Cap Installation and Overhead Cable Openings
• Install Top Cap with [6] M6 Torx Screws
• Cut [4] tabs of each Cutout with wire cutter to open each cable opening - OPTIONAL
• NOTE: If Cutouts are removed, Panduit recommends installing CTCN1X5 Bezel and Cover (not included) for cable protection.
[2] M6 Torx Screws
(use T30 Torx bit)
Top Cap
(note orientation)
For Technical Support: www.panduit.com/resources/install_maintain.asp
REMOVE CUTOUTS - OPTIONAL
(for cable exit/entry - see note)
[2] 40mm x 131mm Openings
[1.57” x 5.15”]
Page 8 of 12
INSTRUCTIONS CM661A
Grounding
• Attach Grounding Lug or Grounding Bar at any of the [2] location(s) shown below
• Grounding location is indicated by universal ground symbol
• Use M5 bonding screws (not included)
[8] Grounding Lug Locations
(Front and Rear of Beams)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 12
INSTRUCTIONS CM661A
Door & Side Panel Bumper Installation
• Install [4] Rubber Bumpers on each side panel
• Install [5] Rubber Bumpers (for 24 RU doors) or [3] Rubber Bumpers (for 12 RU doors) on each door
•
NOTE - Front Door is indicated by PANDUIT label
Rubber Bumper
[installed]
Rubber Bumper
[installed]
24 RU
ONLY
[5] Rubber Bumpers
(24 RU Doors)
[4] Rubber
Bumpers
-or-
[3] Rubber Bumpers
(12 RU Doors)
24 RU
ONLY
PANDUIT Label
indicates front
door
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 10 of 12
INSTRUCTIONS CM661A
Front & Rear Doors (Installation and Removal)
• Install [2] Door Handles and [2] Quarter-turn Lock Assemblies (as shown below)
• Align [4] Locating Pins of each Hinge Bracket with matching hole pattern of cabinet frame
• Secure [4] Hinge Brackets to cabinet frame ([2] left-front / [2] right-rear) with [1] M6 Torx Screw per bracket
• Open Door(s) to approximately 90º
• Lift Door(s) up and insert hinge pins of door(s) into hinge brackets
• REVERSE STEPS to remove split doors
•
IMPORTANT - Use M6 x 12.0mm screws with nylon patch for mounting hinge brackets ([4] screws packed with hinge brackets)
[4] Locating Pins
[2] Door
Handles
(Snap in)
[2] Quarter-turn
Lock Assemblies
(use Phillips screwdriver and 27mm
[4] M6 x 12.0mm Torx Screws
(use T30 Torx bit)
[4] Hinge
Brackets
wrench)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 11 of 12
INSTRUCTIONS CM661A
Side Panels (Removal and Installation)
• Install [2] Quarter-turn Lock Assemblies (as shown below)
• Move Side Panel into place and insert tabs of panel into slots in beam of cabinet frame
• Push top of Side Panel towards cabinet frame
• Lock Side Panels
• REVERSE STEPS to remove Side Panel
[2] Quarter-turn
Lock Assemblies
(use Phillips screwdriver and 27mm
wrench)
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
Side Panel Tabs
www.panduit.com
Page 12 of 12
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...