Mounting Kits
(sold separately)
Front/Rear Front Only
WMPVCBE, NRVCB
(Center Mount)
WMPV22E
WMPVF22E
(Standard mounting for
WMPV45E WMPVF45E
Panduit 2 and 4 post racks
WMPVHC45E
WMPVHCF45E
racks. One kit Included.)
NRV6 NRVF6
NRV10 NRVF10
NRV12 NRVF12
VERTICAL CABLE
MANAGEMENT
R4P Series of Racks
R2P Series of Racks
Doors
WMPV Includes
Cover
NRD6B1
NRD10B1
NRD12B1
Racks
R2P Series of Racks
R4P Series of Racks
ER4P Series of Racks
WMPVSMK (Side Mount)
(Optional Mounting for
4 post racks and R2PS)
(Required Mounting for R2P6S)
NETRUNNER Vertical Cable Managers
© Panduit Corp. 2017
PART NUMBERS
Table 1
Dimensions in () parenthesis are for 6” Vertical Cable Management
INSTRUCTIONS CM308F
Location Guide for Center Mounting
(R2P with WMPVCBE and NRVCB)
Bracket Installation
1
Standard Rack Installation
2
Rear Bottom Mounting
Location
Note:
For additional brackets when
installing between two racks use
part number WMPVCBE or
NRVCB. Bracket is keyed to be
installed in the correct orientation.
Note:
Arrows and flags
must point upward
3
4
#12-24 Screws
Bottom Mounting Location
#12-24 Screws
Location pin(s)
Top Mounting Location
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 1 of 3
INSTRUCTIONS CM308F
Installation Instructions R2PS using WMPVSMK side mounting kit
Note: Mount the racks to the floor (with the appropriate space between racks indicated in Table 2.)
Table 2
1
3/8 Bolt, Lock
Washer & Nut
Location pin(s)
2
* FOR USE WITH R2P6S
3
3/8 Bolt, Lock
Washer & Nut
Installation Instructions Required mounting for R2P6S using WMPVSMK side mounting kit
Note: Mount the racks to the floor (with the appropriate space between racks indicated in Table 2.)
3
1
3/8 Bolt, Lock
Washer & Nut
Location pin(s)
3/8 Bolt, Lock
Washer & Nut
2
Installing Front Only Managers for
Front and Back cable management.
Use a front only manager for additional
cable management on the back of the
rack (see Table 2 for all compatible
managers for this rack)
Front Only
Manager
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 2 of 3
Front Only
Manager
INSTRUCTIONS CM308F
Installation Instructions R4P using WMPVSMK side mounting kit
Note: Mount the racks to the floor (with the appropriate space between racks indicated in Table 2.)
1
3/8 Bolt, Lock
Washer & Nut
Location pin(s)
2
3/8 Bolt, Lock
Washer & Nut
3
Opening and Closing Cover for WMPV managers
Opening
Open
Opening and Closing Cover for NRV managers
Door Latches
Door
Finger
Tab s
Closing
Wire Retainer Installation
(WR5E) SOLD SEPERATELY
Use thumb to release
wire retainer for removal
Removal
Top Latch
Buttons
Installation
Line up finger tabs with door latches.
Then squeeze door and fingers
together to engage (4 places).
For instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
To o p e n , grasp back of
door and push top button
with thumb. Repeat with
bottom button.
To close, grasp cable
retainers and door until
latched
www.panduit.com
Page 3 of 3
Bottom Latch
Buttons
Removal
To remove door, press bottom
latches first, then press top latch
bottons while holding door
E-mail:
techsupport@panduit.com
Fax:
(866)405-6654
Loading...