45° Up/Down UTP TG Modular Jacks & Wire Caps
Jack
45° Up/Down
Wire Cap
Category 6A
(CJUDCAPBU-^)
Category 6
(CJUDCAPIW-^)
Category 5e
(CJUDCAPRD-^)
IMPORTANT!: Determine the desired direction of cable before wiring the cap. The cap, in relation to the
jack, must be kept consistent throughout the entire termination.
Understanding the Label
Down Orientation
Up Orientation
Follow solid line
instructions for
Up Orientation.
(pages 2-3)
Follow dotted line
instructions for
Down Orientation.
(pages 4-5)
STANDARD
CJ%%88TG**
SPRING SHUTTERED
CJH%%88TG**
KEYED
CJK%%88TG**
CORROSION RESISTANT
CJE%%88TG**
Compatible Jack Modules
45° ANGLED JACK
CJUD%%88TG**
(CAT 6 & 6A ONLY)
Part Numbers: CJUDCAPBU-^, CJUDCAPIW-^, CJUDCAPRD-^, CJUD%%88TG**
© Panduit Corp. 2018
INSTALLATION INSTRUCTIONS
PN610C
%% Denotes Category. ** Denotes color.
^ Denotes package quantity (X=10, C=100)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 6
© Panduit Corp. 2018
1
IMPORTANT!:
Be sure that
strain relief is fully
retracted before
inserting cable.
Up Orientation
1.5”
(38.1mm)
0.5”
(12.7mm)
1.5”
(38.1mm)
0.5”
(12.7mm)
Cable End 1
2
Cable End 2
1
2
Bend wires to
ease inserting
them into the
cap.
Be sure cable is fully
inserted into wire cap
TGSJT
6
Cable End 1 Shown
INSTALLATION INSTRUCTIONS
PN610C
Do not pre-arrange
conductors.
3
4
5
Cable End 1 Shown
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 6
Cable
End
(1)
Cable
End
(2)
© Panduit Corp. 2018
A
A
A
A
B
B
7
T568B Wiring
T568A Wiring
Termination side Label side
1.
1. 2.
1.
1. 2.
2.
AAA
A
Termination side
Label side
BBB
B
Cable End 1
Cable End 2
Cable End 1
Cable End 2
T568A not shown on wire map label
9
Important!
Maintain orientation of
cap in relation to jack
from previous steps.
8
INSTALLATION INSTRUCTIONS
Up Orientation
PN610C
10
11
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 6
© Panduit Corp. 2018
Be sure cable is fully
inserted into wire cap
TGSJT
6
Cable End 1 Shown
1
2
1.5”
(38.1mm)
0.5”
(12.7mm)
1.5”
(38.1mm)
0.5”
(12.7mm)
2
Cable End 2
Cable End 1
INSTALLATION INSTRUCTIONS
Down Orientation
PN610C
IMPORTANT!:
Be sure that
strain relief is fully
retracted before
inserting cable.
Do not pre-arrange
conductors.
3
Bend wires to
ease inserting
them into the
cap.
4
5
Cable End 1 Shown
For Technical Support: www.panduit.com/resources/install_maintain.asp
Cable
End
(1)
Cable
End
(2)
Page 4 of 6
© Panduit Corp. 2018
A
A
A
A
B
B
B
B
A
A
B
B
A
A
B
B
1.
1. 2.
7
T568B Wiring
T568A Wiring
1.
1.
2.
2.
Termination side
Label side
Termination side
Label side
T568A not shown on wire map label
Cable End 1
Cable End 2
Cable End 1
Cable End 2
8
Important!
Maintain orientation of
cap in relation to jack
from previous steps.
9
INSTALLATION INSTRUCTIONS
Down Orientation
PN610C
10
11
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 6
© Panduit Corp. 2018
3
2
1
INSTALLATION INSTRUCTIONS
REMOVAL STEPS
Notes:
1. For specified performance, follow TIA/EIA 568-C installation guidelines.
2. Jack Modules can terminate 22-26 AWG solid data cable with 0.062" (1.57mm) maximum insulated conductor outside diameter.
3. Jack Modules may be re-terminated at least 20 times.
4. For technical and performance information, consult Panduit Technical Support.
As with all Wiring Accessories, the following statements apply:
1. Never install communications wiring during a lightning storm.
2. Never install communications wiring in wet locations unless the jack is specifically designed for use in wet locations.
3. Never touch uninsulated communications wiring or terminals unless the communication line has been disconnected at the network interface.
4. Use caution when installing or modifying communication wiring.
PN610C
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Page 6 of 6
Loading...