Page 1
Inlet Duct for 9372 Switch
Part Number(s) : CID1RU22-23DB1
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Inlet Duct is designed for Cabinet with
equipment mounting rails spaced at 29.2”.
Equipment
mounting
rail
29.2”
V00029HP
Inlet Duct includes:
Inlet Duct Qty. 1
Front Perforated Plate Qty. 1
Hardware Included
#12-24 Bonding
Cage Nut Kit
4 of each
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 5
#12-24
Cage Nut
2x
#12-24 X 1/2
Round Head Screw
2x
Page 2
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Install Bonding Cage Nuts into the front equipment mounting rails at the desired RU location
#12-24 Bonding Cage Nut 4X
The four #12-24
Bonding Cage Nuts
must be installed in the
top two positions
as shown.
#12-24 Cage Nut 2X
Front View of Cage Nut locations
Note: The Bonding Cage
Nuts have 3 serrations
on either side.
V00029HP
Locations for the #12-24
Bonding Cage Nuts 4X
Locations for the #12-24
Cage Nuts 2X
Install Inlet Duct onto the front equipment mounting rails
#12-24 Grounding Screws 2X
#12-24 Round Head
Screw 2X
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 5
Page 3
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Install 9372 Switch to the Rails and seal the Inlet Duct to the Switch
V00029HP
Remove the Rear Brackets from the Switch (NOT INCLUDED).
1
Route cables from back of the
Switch thru the Brush Seals
Switch to nest inside of tray
light grey areas
Install 9372 Switch (NOT INCLUDED) onto the
2
back Rails and into the back of the Inlet Duct.
Brush Seal
Both sides
Loosen the M5 Nut located inside the Inlet Duct to allow
3
the Sliding Plate to be pushed back against the Switch.
8mm Wrench
M5 Nut
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 5
Page 4
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
V00029HP
4
Slide the Sliding Plate back until
the Bulb Seal and brushes seal
against the Switch.
Re-tighten the M5 Nut that
5
was loosened in Step 2.
Bulb Seal
Cables
M5 Nut
(Inside Duct)
Install Perforated Front Cover to Inlet Duct
1
Cables
2
#12-24 Grounding Screws 2X
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 5
Page 5
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installation of the Inlet Duct directly above previously installed equipment
Use at head screwdriver to prop up switch. This will allow the
1
bottom lip of the Inlet Duct to slide under the switch.
Switch
Pull the screwdriver out thru the Inlet Duct opening after the
2
Inlet Duct has been installed.
V00029HP
Allow the screwdriver to
pass thru the opening in
Inlet Duct as the Inlet
Duct is installed.
Equipment
Installation of a 2nd Inlet Duct directly above another Inlet Duct
Pull the Bulb Seal off of the bottom
Inlet Duct and discard before installing the
2nd Inlet Duct above it .
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 5 of 5
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...