
Stainless Steel Trefoil Cable Cleat
Cable Cleat for the Protection and Support
of Insulted Power Cables in Trefoil Arrangement
INSTALLATION INSTRUCTIONS
TO REDUCE THE RISK OF INJURY, USER
MUST READ INSTALLATION INSTRUCTIONS
BEFORE ATTEMPTING TO INSTALL
NOTE: In the interest of higher quality and value, Panduit products are
continually being improved and updated. Consequently, pictures
may vary from the enclosed product.
NOTE: Updates to this Installation Instructions may be available. Check
www.panduit.com for the latest version of this manual.

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 2 of 8 Rev 00 [05-2019]
Email:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
Panduit Corp.
USA Technical Support
Tel: 800-777-3300
Panduit Europe • EMEA Service Center
Tel: +31 546 580 452 • Fax: +31 546 580 441
Contact Panduit Sales for
assistance with cleat and
hardware selection.
Measure actual diameter of
the cables. Select a cleat part
number based on the actual
diameter of the cables.
Measure height of the ladder
rung. If using a bracket,
reference chart below. If using
a bolt, procure M8 or 5/16”
carriage bolts, washers, and
nylon locknuts with sufficient
length to pass through the
ladder rung.
15mm (.59”) to 20mm
(.79”)
20mm (.79”) to 25mm
(.98”)
25mm (.98”) to 30mm
(1.16”)

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 3 of 8 Rev 00 [05-2019]
Cable Cleat Nomenclature
Fastening Bolt, Washer, and
Locknut (Included in Package)
Securing Bolt, Washer,
and Locknut
Swing Bolt with
Flanged Nut
Unslotted Ladder Rack/Rung
Cables, Trefoil Configuration

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 4 of 8 Rev 00 [05-2019]
Mounting Method 1: Bracket
Measure the cable diameter.
Remove top plastic spacer
depending on cable
diameter. See table on page
8.
2
Insert bracket into slot in
lower plastic spacer of cable
cleat.
Slide cleat over rung until
centered, with bracket
encompassing the rung.

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 5 of 8 Rev 00 [05-2019]
Rotate swing bolt until the
carriage head rests within
the matching opening in the
top of the bracket. Tighten
flange nut to 60 in-lbs
[6.8Nm].
Open top clamshell and
place trefoil cables in the
opening in a trefoil
configuration. Close top
clamshell around the cables.
Assemble included nut and
washer onto the securing
bolt. Tighten to 15 ft-lbs
[20.3Nm].

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 6 of 8 Rev 00 [05-2019]
Mounting Method 2: Bolt
Remove top plastic spacer
to allow access to the bolt
hole.
Position cleat over the
appropriate hole in the rung.
Assemble securing carriage
bolt through the hole in the
bottom of the cleat.
Tighten securing bolt to 120
in-lbs [13.6Nm].

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 7 of 8 Rev 00 [05-2019]
Measure the cable diameter.
Remove top plastic spacer
depending on cable
diameter. See table on page
8.
Open top clamshell and
place cables in the opening
in a trefoil configuration.
Close top clamshell around
the cables.
Assemble included nut and
washer onto the securing
bolt. Tighten to 15 ft-lbs
[20.3Nm].

INSTALLATION INSTRUCTIONS
DOC#: RW316 Page 8 of 8 Rev 00 [05-2019]
Spacer Decision Table