Page 1
Vertical Exhaust Duct for N-Type
and S-Type Cabinets
Part Number(s): C2VED06I1626**, C2VED06I2638**, C2VED06I3866**, C2VED07I1626**,
C2VED07I2638**, C2VED07I3866**, C2VED08I1626**, C2VED08I2638**, C2VED08I3866**
© Panduit Corp. 2012
Vertical Exhaust
Duct for N-Type
and S-Type
Cabinet
INSTALLATION INSTRUCTIONS
COMPONENT GUIDE
Note: Top Flange Length is
Longer than on Top Rear
Panel.
CM595
Vertical Exhaust
Duct for N-Type
and S-Type
Cabinet
Extended
Note: Top Flange
Length is Shorter
than on Top Front
Panel.
(2) Bottom Front
and Rear Panel
(2) Bottom Side
Panels
(1) Top Front
Panel
(1) Top Rear
Panel
(2) Horizontal
Adjustment
Brackets
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 14
(2) Top Side
Panels
(1) Hardware kit
(Not Shown)
Page 2
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 1
Connecting Top Front and Top Rear Panels to Top Side Panels
• Align clips on top rear panel with slots in top side panel. (View A)
• Insert clips on top rear panel with slots in top side panel. (View B)
• Slide side panel down locking top rear panel and top side panel together. (View C)
• Repeat steps to connect second top side panel and top front panel.
Top Side
Panel
Top Rear
Panel
CM595
Top Rear
Panel
Clip
CAUTION:
Possible Pinch
Point
Top Side
Panel
Slot
View B
View A
View C
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 14
Page 3
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 2
Attaching Horizontal Adjustment Brackets
• Using (4) M5 x 12mm button head screws, attach (2) horizontal adjustment brackets to the top of the top
front and rear panels. (Leave screws loose.)
(2) Horizontal
Adjustment
Brackets
CM595
(4) M5 x 12mm
button head
screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 14
Page 4
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM595
Step 3
Securing Top Panels Together
• Secure 4 panels making up the top half of the vertical exhaust duct with (8) M5 x 12mm button head screws.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 14
(8) M5 x 12mm
button head
screws
Page 5
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 4
Set Width of Horizontal Adjustment Brackets (For Single Vertical
Exhaust Duct Installation)
• Measure required side to side opening needed for the top of the vertical exhaust duct.
• Adjust horizontal adjustment brackets to match opening.
• Tighten horizontal adjustment bracket screws.
• NOTE: For more than one vertical exhaust duct, ganging bracket installation is required. (Ref. page 14)
Width of Opening
in Ceiling
CM595
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 14
Page 6
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 5
Connecting Bottom Front and Bottom Rear Panels to Bottom Side
Panels
• Align clips on bottom rear panel with slots in bottom side panel. (View D)
• Insert clips on bottom rear panel with slots in bottom side panel. (View E)
• Slide bottom rear panel down locking bottom rear panel and bottom side panel together. (View F)
• Repeat steps to connect second bottom side panel and bottom front panel.
Bottom Rear
Panel
Bottom Side
Panel Slot
CM595
Bottom Rear
Panel Clip
Bottom Side
Panel
View E
CAUTION:
Possible Pinch
Point
View D
View F
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 14
Page 7
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 6
Securing Bottom Panels Together
• Secure 4 panels making up the bottom half of the vertical exhaust duct with (4) M5 x 12mm button head
screws.
CM595
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 7 of 14
(4) M5 x 12mm
button head
screws
Page 8
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM595
Step 7
Assembling Top and Bottom Halves of Vertical Exhaust Duct
• Place bottom half of vertical exhaust duct on the floor.
• Align the top half of the vertical exhaust duct over the bottom half and slide the top half over the bottom half.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 8 of 14
Page 9
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 8
Inserting Adjustment Nuts
• Insert (4) adjustment nuts into the slots on the inside of the bottom half of the vertical exhaust duct making
sure that the barbs on the adjustment nuts are facing outward.
(4) Adjustment
Nuts
(4) Slots on
Inside of Bottom
Half of Vertical
Exhaust Duct
CM595
Note: Barbs on
Adjustment Nuts
Must Face Outward
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 14
Page 10
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 9
Securing Top and Bottom Halves of Vertical Exhaust Duct
• Fasten (4) M8 x 12mm button head screws with (4) M8 lock washers through the top half of the vertical
exhaust duct into the (4) adjustment nuts.
CM595
(4) M8 x 12mm Button
Head Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
(4) M8 Lock Washers
(Required for
Electrical Bonding)
Page 10 of 14
Page 11
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 10
Applying Foam Seal to Top of Vertical Exhaust Duct
• Measure and cut (2) pieces of 12.7mm x 25.4mm (0.5" x 1.0") and (2) pieces of 25.4mm x 25.4mm
(1.0" x 1.0") foam seal to match the length and width of the vertical exhaust duct.
• Attach foam seal to the top border of the vertical exhaust duct.
(2) 25.4mm x 25.4mm
(1.0" x 1.0") Foam Seals
CM595
(2) 12.7mm x 25.4mm
(0.5" x 1.0") Foam Seals
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 11 of 14
Page 12
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 11
Attaching Vertical Exhaust Duct to Cabinet
(For ease of installation a minimum of (2) persons are suggested for this assembly step)
• Determine front and rear of the vertical exhaust duct and cabinet.
• Carefully lift vertical exhaust duct and place over opening in the top of the cabinet.
• Secure vertical exhaust duct to cabinet with M5 x 10mm hex head screws.
• Note: Number of M5 x 10mm hex head screws required will vary depending on the width of the vertical
exhaust duct. Extra screws may remain.
CM595
Top Front Panel
M5 x 10mm Hex
Head Screws
Front of Cabinet
Note: Shorter Top
Flange is to the Rear of
the Cabinet.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 12 of 14
Page 13
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 12
Adjust Height of Vertical Exhaust Duct
(For ease of installation a minimum of (2) persons are suggested for this assembly step)
• Loosen the (4) M8 x 12mm screws on the front and rear of the vertical exhaust duct.
• Slide the top half of the vertical exhaust duct up to required height.
• Tighten the (4) M8 x 12mm screws on the front and rear of vertical exhaust duct.
• Torque screws to 3.1 N/m (27 in/lbs) minimum.
(4) M8 x 12mm Button
Head Screws
CM595
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 13 of 14
Page 14
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
Step 13
Attaching Ganging Brackets
• Remove (4) M5 x 12mm button head screws from the front and rear of the (2) vertical exhaust ducts you
will be ganging.
• Use these screws to attach the (2) ganging brackets to the (2) vertical exhaust ducts.
• Loosen horizontal adjustment brackets screws and adjust the horizontal adjustment brackets to close
any gaps between vertical exhaust ducts.
• Tighten screws.
(2) Ganging Brackets
CM595
(4) M5 x 12mm Button
Head Screws
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 14 of 14
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...