Panduit C2CEOR04CP8B1 Installation Manual

Page 1
Cabinet Supported End of Row Cap
Part Number(s) : C2CEORO*CP*B1
© Panduit Corp. 2015
(1) 900mm Bottom Panel Guide
(1) 900mm Vertical Wall Blanking Panel
(2) End of Row Polycarbonate Panel 900 Wide
(2) Vertical Panel Clamp, Wide
(2) Corner Bracket, Right-Hand
(2) Corner Bracket, Left-Hand
(1) 900mm Roong Blanking Panel
(1) 1200mm Floor Seal Panel
(1) 1200mm Bottom Panel Guide
(1) 1200mm Vertical Wall Blanking Panel
(2) End of Row Polycarbonate Panel 1200 Wide
(2) Vertical Panel Clamp, Wide
(2) Corner Bracket, Right-Hand
(2) Corner Bracket, Left-Hand
(1) 1200mm Roong Blanking Panel
C2CEOR03CP*B1
(2) Vertical Panel Clamp
(4) Horizontal Panel Clamp
(1) Column, Right-Hand
(1) Column, Left-Hand
(1) 900mm Upper Panel
(1) Vertical Panel Support
(1) 900mm End Beam
(1) Hardware Kit
C2CEOR04CP*B1
(2) Vertical Panel Clamp
(4) Horizontal Panel Clamp
(1) Column, Right-Hand
(1) Column, Left-Hand
(1) 1200mm Upper Panel
(1) Vertical Panel Support
(1) 1200mm End Beam
(1) Hardware Kit
INSTALLATION INSTRUCTIONS
V00029HI
C2CEOR06CP*B1
(1) 1800mm Floor Seal Panel
(1) 1800mm Bottom Panel Guide
(3) End of Row Polycarbonate Panel 1200 Wide
(2) Vertical Panel Clamp, Wide
(4) Vertical Panel Clamp
(6) Horizontal Panel Clamp
(2) Corner Bracket, Right-Hand
(2) Corner Bracket, Left-Hand
(1) Column, Right-Hand
(1) Column, Left-Hand
(1) 1800mm Upper Panel
(2) Vertical Panel Support
(1) 1800mm End Beam
(1) Hardware Kit
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 10
Page 2
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installing Left and Right Hand Corner Brackets to S-Type Cabinets
V00029HI
1
Tap the knock-outs out from the top and bottom of
cabinets where the End of Row Cap will be installed.
Make sure the knock-out tab is removed
fully from the opening.
Knock-out
2
Install Cage Nuts in the knock-out
openings and turn 1/4 turn to secure.
1/4
Turn
3
M6 x 10mm
Hex Head Bonding Screw
4 places per side
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 10
Page 3
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installing Left and Right Hand Corner Brackets to N-Type Cabinets
M6 x 10mm
Hex Head
Bonding Screw
4 places per side
V00029HI
M5 x 10mm
Hex Head Bonding Screw
4 places per side
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 10
Page 4
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installing Left and Right Hand Columns to Cabinets
Install 1” x 1” Foam Seal to
1
both Columns
2
V00029HI
1” x 1 ” Foam
M6 Serrated Flange
Hex Nut
2 places per side
M6 Serrated Flange
Hex Nut
2 places per side
Note the height and side stamping. This
stamping is always
located at the top and
contains a ‘R’ or ‘L’
to determine the side
of containment, as
viewed from the inside
of the containment
that it will attach to.
‘R’ for the right side
and ‘L’ for the left side.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 10
Page 5
© Panduit Corp. 2015
Installing Floor Seal to Columns
1
Install 1” x 1” Foam Seal to Floor Seal Panel
2
Attach Floor Seal Panel to Bottom Panel Guide
INSTALLATION INSTRUCTIONS
1” x 1” Foam
V00029HI
M5 x 0.8 Serrated
Flange Hex Nut
2 places
DO NOT
TIGHTEN YET
3
After attaching the Floor
Seal. Push the Foam Seal
tight against the oor and
tighten the 2 M5 x 0.8 Hex
Nuts left loose in Step 2.
M6 Serrated Flange
Hex Nut 2 places
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 10
Page 6
© Panduit Corp. 2015
Installing Upper Panel
M6 Serrated Flange
Hex Nut 2 places
INSTALLATION INSTRUCTIONS
V00029HI
Installing End Beam to Roong Blanking Panel for Roong Application
M5 Serrated Flange
Hex Nut 3 places
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 10
Page 7
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installing Roong Blanking Panel to Upper Panel for Roong Application
1
Foam Seals
Trimmed to t wall Panel
2 places
V00029HI
2
M6 Serrated Flange
Hex Nut 4 places
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 7 of 10
Page 8
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
V00029HI
3
M6 x 12mm
Serrated Flange
Hex Head Screw
2 places
4
This Application is completed
with LCAC Roong Assemblies
purchased separately.
(C2CAC0**FO**R**)
M6 Serrated Flange
Hex Nut 2 places
C2CAC0**FO**R**
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 8 of 10
Page 9
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
V00029HI
Installing Vertical Wall Blanking Panel to Upper Panel for Vertical Wall Application
1
Install 3 sections of 1” x 1” Foam Seal to Vertical Wall Blanking Panel
2
1” x 1” Foam
M6 Serrated
Flange Hex Nut
4 places
3
This Application is completed with
HAC Vertical Wall Assemblies
purchased separately.
HAC Vertical Wall
Assemblies
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 10
Page 10
© Panduit Corp. 2015
INSTALLATION INSTRUCTIONS
Installing the Vertical Panel Support, Panels , and Panel Clamps
1
M5 x 0.8 Serrated
Flange Hex Nut
4 places
V00029HI
2
M5 x 0.8 Serrated
Flange Hex Nut
2 places each
Horizontal Clamp
M5 x 0.8 Serrated
Flange Hex Nut
5 places each
Vertical Clamp
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 10 of 10
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...