Panduit C2CAC06ABWPAB1 Installation Manual

Net-Contain Row Base Cooler
Blanking Panels
Part Number(s): C2CAC06ABWPA**, C2CAC04ABWPA**, C2CAC03ABWPA**
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM640A
Cover
(2) Top Bracket
(1) Blanking Panel
Extension
(1) Floor Seal
(1) Blanking Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 1
Cabinet Alignment and Set Up
Reference CM596 for cabinet alignment and set up.
STEP 2
Initial Wall Panel Installation
Reference CM596 for initial wall panel installation.
CM640A
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 3
Attaching Foam Seal to Wall Panel
Trim foam seal to required lengths to cover one side of the wall panel.
Note: Do not apply foam to the side of the row base cooler wall panel that will be against the cold aisle containment wall panel that already has foam on it.
Wall Panel
CM640A
(1) .75 x .5 Foam
Seal
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM640A
STEP 4
Attaching First Top Bracket
Insert (1) top bracket into a wall panel adjacent to the row base cooler unit.
Align (2) of the holes in the top bracket with the slots in the wall panel having half of the top bracket sticking out of the side of the wall panel.
Secure the top bracket to the wall panel with (2) M5 x 12mm button head screws. (Leave screws loose.)
(2) M5 x 12mm
Button Head
Screws
Top Bracket
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 4 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 5
Sliding Wall Panel into Place
Slide wall panel onto the top bracket.
Position the front of the wall panel to be in line with the front of the adjacent wall panels.
Top Bracket
CM640A
Wall Panel
In Line with
Adjacent Wall
Panels
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 5 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 6
Attaching Second Top Bracket
Insert top bracket into the front of the wall panel.
Position the holes in the top of the top bracket with the slots in the wall panel and the adjacent wall panel.
Secure the top bracket to the adjacent wall panel with (2) M5 x 12mm button head screws. (Leave screws loose.)
CM640A
Wall Panel
Top Bracket
(2) M5 x 12mm
Button Head
Screws
Adjacent
Wall Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 6 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 7
Securing Wall Panel to Top Brackets
Secure the wall panel to the (2) top brackets with (4) M5 x 12mm button head screws.
Tighten screws that were previously left loose.
CM640A
Wall Panel
(4) M5 x 12mm
Button Head
Screws
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 7 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM640A
STEP 8
Checking Distance From Wall Panel to Row Base Cooler Unit
Measure the distance from the bottom of the wall straight down to the top of the row base cooler unit.
If distance in less than 89mm (3.5") only the blanking panel is needed.
If distance is greater than 89mm (3.5") blanking panel with blanking panel extension will be needed. (Skip to page 11)
Measure to see if
distance is less than
or greater than
89mm (3.5").
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 8 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM640A
STEP 9
Attaching Foam to Blanking Panel (Only if Blanking Panel Extension is not needed.)
Note: If blanking panel extension is needed skip to page 10.
Cut (2) strips of foam seal to the length of the sides of the blanking panel.
Cut (1) strip of foam seal to the length of the bottom of the blanking panel.
Attach all (3) strips of foam seal to the blanking panel.
(2) .75 x .5 Foam
Seals
(1) .75 x .5 Foam
Seal
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 9 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 10
Attaching Blanking Panel (With no Blanking Panel Extension)
Slide blanking panel into place behind wall panel.
Attach blanking panel to wall panel with (2) M5 x 12mm button head screws.
Any unused screw holes that are exposed can be plugged using the screws provided.
Note: Skip to page 15 to install floor seal.
CM640A
(2) M5 x 12mm
Button Head
Screws
Blanking
Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 10 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
CM640A
STEP 11
Attaching Blanking Panel to Blanking Panel Extension
Slide the blanking panel into place behind the blanking panel extension.
Secure the blanking panel to the blanking panel extension with (2) M5 x 12mm button head screws. (Leave screws loose.)
Blanking Panel
Extension
(2) M5 x 12mm
Button Head
Screws
Blanking
Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 11 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 12
Attaching Blanking Panel Assembly to Wall Panel
Insert the studs on the front of the blanking panel assembly into the slots in the rear of the wall panel.
Loosely attach blanking panel assembly to the wall panel with (2) M5 hex nuts.
CM640A
(2) M5 Hex
Nuts
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 12 of 18
Blanking
Panel Assembly
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 13
Adjusting Height of Blanking Panels
With the (2) M5 hex nuts on the blanking panel extension and the (4) M5 x 12mm button head screws on the blanking panel loose, adjust the height of the blanking panels to form a complete and tight seal with the top on the row base cooler unit.
Tighten the (2) M5 x 12mm button head screws on the blanking panel.
Remove the (2) M5 hex nuts from the blanking panel assembly.
Remove blanking panel assembly from the wall panel.
(2) M5 Hex
Nuts
Blanking Panel
CM640A
Extension
(2) M5 x 12mm
Button Head
Screws
Adjust Height of
Blanking Panel and
Blanking Panel
Extension to Form
a Tight Seal.
Blanking
Panel
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 13 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 14
Attaching Foam Seal to Blanking Panel Assembly
Cut (2) strips of foam seal to the full length of the sides of the blanking panel assembly.
Cut (1) strip of foam seal to the length of the bottom of the blanking panel assembly.
Attach all (3) strips of foam seal to the blanking panel assembly.
CM640A
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 14 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 15
Attaching Blanking Panel Assembly to Wall Panel
From under the wall panel, slide the blanking panel assembly into place with the studs on the blanking panel assembly into the slots in the wall panel.
Pressing the blanking panel assembly down against the row base cooler unit fasten the blanking panel assembly to the wall panel with (2) M5 hex nuts.
Any unused screw holes that are exposed can be plugged using the screws provided.
CM640A
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 15 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 16
Setting Up Floor Seal
Measure the distance from the bottom of the row base cooler unit to the floor.
Apply the appropriate amount of either .5" x .75" or 1" x 1" foam seal to the top and/or bottom of the floor seal bracket to make a tight fit between the row base cooler unit and the floor.
CM640A
Distance from the
Bottom of the In-Row
Cooling Unit and the
Floor
Foam Seal
(As Needed)
Floor Seal
Bracket
Foam Seal
(As Needed)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 16 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 17
Inserting Floor Seal Assembly
Slide floor seal assembly in between the floor and the row base cooler unit making sure that the floor seal assembly forms a tight and complete seal to prevent air loss.
Row Base
Cooler
Unit
CM640A
Floor Seal
Assembly
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 17 of 18
© Panduit Corp. 2012
INSTALLATION INSTRUCTIONS
STEP 18
Attaching Ceiling Structure
Reference CM596 to finish installing the ceiling structure for the POD.
CM640A
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 18 of 18
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
Loading...