Atlona has made every eort to make sure that all switches listed in this document, meet or exceed functionality
with OmniStream products, identifying them as OmniStream Certied Switches. Atlona will continue to update this
document as more switches are tested. However, due to the vast number of manufacturers and switch models
on the market today, it is not possible to test each one. Before purchasing a switch that is not included in this
document, make sure that it supports the following features.
IGMP
• IGMP Snooping
• IGMP Querier
• IGMP Immediate Leave
• Unregistered Multicast Flooding
• Static Multicast Groups (optional)
IMPORTANT: Failing to meet all of the above requirements (except for Static Multicast Groups) may
lead to performance issues.
PoE Budget
In addition to the above requirements, the power budget of the PoE switch must be identied. To determine the
maximum number of PoE devices that can be connected to a switch, two factors need to be considered:
1) The PoE budget of the switch.
2) The power requirements of each device.
When purchasing a switch, identify the PoE budget or power dedicated to PoE, in the switch specications.
This number is the total power that the switch can provide when PoE devices are connected. For example, a 24-port
370-watt PoE switch can supply up to 15.4 W of power on all 24 ports. In this case, you can connect 24 OmniStream
units.
NOTE: If connecting OmniStream devices to a non-PoE switch or if using the analog audio
capabilities, then OmniStream units must be connected to the external power supply (Atlona part no.
AT-PS-48083-C). The power supply is not included and sold separately.
OmniStream Certied Switches
4
Page 5
Features of Congurations
• Connect OmniStream devices plug and play.
• Connect management ports to an external network, such as a home router.
NOTE: Devices that are connected to either OmniStream ports (VLAN 10) or management ports
(VLAN 1) on the OmniStream switch will be able to communicate with both the OmniStream units as
well as the Internet (using a connected home router). Devices that are connected to the home router
will only be able to connect to OmniStream devices if a static route is congured on the home router.
Refer to Home Router Static Routing (page 6) on the next page.
Home Router
ID
INPUT
DISPLAY
VOLUME
LINK
HDMI
1 2 1 2
PWR
Encoder
TM
TREAM
S
MNI
Switch
O
Introduction
AMS VM
ID
INPUT
DISPLAY
VOLUME
LINK
HDMI
1 2 1 2
PWR
TM
Encoder
TREAM
S
MNI
O
Legend
ID
LINK
Decoder
1 2
PWR
TM
TREAM
S
MNI
O
ID
LINK
1 2
PWR
Decoder
TM
TREAM
S
MNI
O
VLAN 10
VLAN 1
Known Limitations
• The network conguration le is applicable only to one standalone switch.
• If planning to connect multiple switches together, then a custom conguration will be required.
• Management network must use IP addresses from 192.168.1.1 through 192.168.1.253. If a dierent range is
used, then a custom conguration will be needed.
• The management ports have DHCP disabled, as a typical home router will handle this task. If the system will not
be connected to another network using the management ports, one of the OmniStream ports should be used for
management.
• Without a static route congured on the home router, any devices connected to the home router will not be able
to connect to the OmniStream devices.
• The home router must be set to 192.168.1.x in order for the Internet to be accessible from the OmniStream VLAN
(VLAN 10).
OmniStream Certied Switches
5
Page 6
Introduction
Home Router Static Routing
In order for devices that are connected to the home router, to be able to connect to OmniStream devices on VLAN
10, a static route must be congured on the home router. This static route is required to send the network trac to
the proper destination. Conguring static routing will vary by manufacturer, but most home routers have this ability.
Essentially, the router must be instructed to route any trac bound for the 10.1.0.0/23 range (also referred to as the
range starting with 10.1.0.0 with a subnet mask of 255.255.254.0) will use the gateway 192.168.1.254. However, if
the home router is using the same gateway, then the IP address of the switch must be changed to 192.168.1.253.
NOTE: Without dening a static route on the home router, the system will still function properly but
without connectivity to the OmniStream devices (VLAN 10) from the home router.
A static route for the OmniStream ports (VLAN 10) has been dened assuming that the home router is set to
192.168.1.1. If this is not the case, then the static route will need to be modied to enable Internet access to the
OmniStream VLAN.
NOTE: If the home router is not set to 192.168.1.1, then the conguration le may still be used as is,
but VLAN 10 will not have Internet access.
Ports 1 through 8 can be used to connect OmniStream devices.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 10
* Default gateway: 10.1.1.1
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
Ports 1 through 16 can be used to connect OmniStream devices.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 18
* Default gateway: 10.1.1.1
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
Ports 1 through 24 can be used to connect OmniStream devices.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 26
* Default gateway: 10.1.1.1
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
physical port on the switch.
• Spanning tree mode: RSTP
• IGMP
* Snooping: Enabled
* Immediate leave: Enabled
* Querier: Enabled
OmniStream Certied Switches
9
Page 10
Default Congurations
Instructions for uploading the conguration le for Araknis switches
1. Download the required conguration le.
2. Open a web browser and enter the IP address of the switch in the address bar: 192.168.20.254
3. Enter the login credentials to access the user interface. The default credentials are listed below:
Username: araknis
Password: araknis
4. Click MAINTENANCE > FILE MANAGEMENT.
5. Under the Conguration File section, click the Choose File button and select the conguration le which was
downloaded in Step 1.
Choose File button
OmniStream Certied Switches
10
Page 11
6. Click the From PC button to begin uploading the conguration le to the switch.
Default Congurations
From PC button
7. A Conrmation message box will be displayed. Click OK to dismiss the message box and continue with the
upload procedure.
8. Enter the new IP address of the switch in a web browser window: 10.1.1.254.
9. Conguration is complete. Login to the switch using the following credentials:
Ports 1 through 23 are to be used only for OmniStream.
Ports 24 through 28 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 24 through 28
* Default gateway: 192.168.1.1 (home router for Internet trac)
IMPORTANT: Ports 25 - 28 are SFP interfaces and intended for 1G transceivers.
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used,
then the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 23
* DHCP range: 10.1.0.1 through 10.1.0.255
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.253 range with a
subnet mask of 255.255.254.0.
• DHCP lease time: 7 days
• Spanning tree mode: RPVST
• BPDU guard: Enabled
• Loop protection: Enabled
• SSH: Enabled
OmniStream Certied Switches
• IGMP (VLAN 10 only)
* Snooping: Enabled
* Unregistered ooding: Disabled
* Immediate leave: Enabled
* Querier: Enabled
12
Page 13
Default Congurations
Instructions for uploading the conguration le for Aruba switches
1. Download the required conguration le.
2. Connect a PC to the console port of the Aruba 2930F, using a rollover cable (not provided with switch). If the PC
only has USB ports, a DB9-to-USB serial adapter will be required.
3. Open a terminal session on the PC. The Aruba switch will auto-detect the baud rate and the switch will be
placed in privileged mode, which is idened by the “#” prompt. Switch to global cong mode by typing the
following at the command prompt, then press [ENTER]: cong t
4. Type the following at the global cong mode prompt and press [ENTER]: vlan 1
5. Enter an IP address and subnet mask for the switch, allowing access to the web interface, then press [ENTER]:
ip address 10.1.1.254 255.255.254.0
Refer to the illustration below for reference:
6. Connect the PC to any Ethernet port on the switch, from
1 through 23.
7. Assign the PC Network Interface Controller (NIC) to
an IP address within the range of 10.1.0.0/23. For
example: 10.1.1.200 255.255.254.0. In the
Default gateway eld, enter 10.1.1.254. Refer to the
illustration on the right.
OmniStream Certied Switches
13
Page 14
Default Congurations
8. Open a web browser and enter the gateway IP address of 10.1.1.254.
9. Login to the switch web interface and enter the following credentials, if required:
user: admin
password: (leave blank)
10. Click Conguration > Management and load the Atlona provide Aruba switch conguration.
11. Under the Update section, locate the Select switch conguration le to update: drop-down list and select
cong1 to overwrite this conguration le. By default, this is the start-up conguration lename.
Select “config1”
OmniStream Certied Switches
14
Page 15
12. Click Yes when prompted to overwrite the conguration le.
Default Congurations
13. Switch conguration is complete and will take eect immediately, without the need for a reboot.
Ports 1 through 8 are to be used only for OmniStream.
Ports 9 and 10 are to be used for management and can be connected to another network, such as a router that has
Internet access.
NOTE: Before uploading the conguration, change the System Mode to L3 (router mode).
The System Mode can be changed under Administration > System Settings > System Mode.
Refer to the image on page 5 for more information.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 9 and 10
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 8
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 24 are to be used only for OmniStream.
Ports 25 through 28 are to be used for management and can be connected to another network, such as a router that
has Internet access.
NOTE: Before uploading the conguration, change the System Mode to L3 (router mode).
The System Mode can be changed under Administration > System Settings > System Mode.
Refer to the image on page 5 for more information.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 25 through 28
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 24
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 48 are to be used only for OmniStream.
Ports 49 through 52 are to be used for management and can be connected to another network, such as a router that
has Internet access.
NOTE: Before uploading the conguration, change the System Mode to L3 (router mode).
The System Mode can be changed under Administration > System Settings > System Mode.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
OmniStream Certied Switches
18
Page 19
• VLAN 1
* Ports: 49 through 52
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 48
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
• DHCP lease time: 7 days
• Spanning tree mode: RSTP
• BPDU guard: Enabled
• Green Ethernet: Disabled
• Loop protection: Enabled
• SSH: Enabled
• IGMP (VLAN 10 only)
* Snooping: Enabled
* Unregistered ooding: Disabled
* Immediate leave: Enabled
* Querier: Enabled
* Custom multicast address for AT-OMNI-232 management added
Ports 1 through 8 are to be used only for OmniStream.
Ports 9 and 10 are to be used for management and can be connected to another network, such as a router that has
Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 9 and 10
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 8
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 24 are to be used only for OmniStream.
Ports 25 through 28 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 25 through 28
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 24
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 48 are to be used only for OmniStream.
Ports 49 through 52 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 49 through 52
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 48
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 24 (Gigabit) are to be used only for OmniStream.
Ports 1 through 4 (Ten Gigabit) are to be used for management and can be connected to another network, such as a
router that has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 4
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports (Gigabit): 1 through 24
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 48 (Gigabit) are to be used only for OmniStream.
Ports 1 through 4 (Ten Gigabit) are to be used for management and can be connected to another network, such as a
router that has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 4
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports (Gigabit): 1 through 48
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
NOTE: The same conguration can be used for the Cisco SG550X-24MPP.
Summary
Version: 2.3.5.63
Ports 1 through 24 (Gigabit) are to be used only for OmniStream.
Ports 1 through 4 (Ten Gigabit) are to be used for management and can be connected to another network, such as a
router that has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports (Ten Gigabit): 1 through 4
* Static routing (Ten Gigabit): 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports (Gigabit): 1 through 24
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 48 (Gigabit) are to be used only for OmniStream.
Ports 1 through 4 (Ten Gigabit) are to be used for management and can be connected to another network, such as a
router that has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports (Ten Gigabit): 1 through 4
* Static routing (Gigabit): 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports (Gigabit): 1 through 48
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 24 are to be used only for OmniStream.
Ports 25 through 32 are to be used for management and can be connected to another network, such as a router that
has Internet access. Refer to the technical specications of the switch for usage.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 25 through 32
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 24
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
Ports 1 through 26 are to be used only for OmniStream.
Conguration Details
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 26
* Static routing: 192.168.1.1
NOTE: The Luminex GigaCore26i switch cannot act as a DHCP server. For installations that require
DHCP, connect an external DHCP server to the switch. The Luminex GigaCore26i switch is a L2
switch and can accommodate multiple L2 VLANs or networks, but cannot route between those
networks. In order to route trac between multiple VLANs, a user has to connect a router that will
handle the routing between multiple networks.
• VLAN 1
* Ports: 1 through 26
* DHCP range: N/A
• DHCP lease time: N/A
• Spanning tree mode: RSTP
• BPDU guard: Enabled
• Green Ethernet: Disabled
• Loop Protection: Enabled
• SSH: Enabled
• IGMP
* Snooping: Enabled
* Unregistered ooding: Disabled
* Immediate leave: Enabled
* Querier: Enabled
OmniStream Certied Switches
28
Page 29
Instructions for uploading the conguration le for the Luminex GigaCore 26i
NOTE: The default IP address of the switch is 192.168.13.53 (255.255.0.0).
1. Download the Luminex GigaCore 26i conguration le from the link on page 5.
2. Open a web browser and enter the IP address of the switch in the address bar.
3. Enter the login credentials. The following are the default login credentials:
Username: admin
Password: (no password)
4. Click Proles in the side menu bar to access the Prole Manager.
Default Congurations
5. In the Prole Manager window group, click the Import button and select the Luminex GigaCore 26i Conguration for Atlona OmniStream.txt le.
OmniStream Certied Switches
29
Page 30
Default Congurations
Once the le has been uploaded, a message box will be displayed indicating that the import procedure was
successful. Click the “X” in the upper-right corner of the message box to dismiss it.
6. Click the Recall button. The Recall Prole dialog box will be displayed. Click Recall all, as shown on the next
page.
NOTE: After the Recall all button is clicked, the switch will reboot and load the Atlona conguration
le. The IP address of the switch will change from 192.168.13.53 (255.255.0.0) to 192.168.1.254
(255.255.255.0).
7. Change the IP address of the laptop to match the IP address range of the switch.
8. Login to the switch with the following credentials:
Username: admin
Password: Atlona
NOTE: This conguration is based on VLAN 1. If a user requires conguration for a specic VLAN,
then it will need to be a custom conguration.
Ports 1 through 24 can be used to connect OmniStream devices.
Ports 25 through 28 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://192.168.1.254
VLAN 10: http://10.1.1.254
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 25 through 28
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 24
* DHCP range: 10.1.0.1 through 10.1.1.0
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.253 range with a
subnet mask of 255.255.254.0.
IMPORTANT: The GSM4352PA model provides a 480 W PoE budget with a single power supply.
Depending on the number of connected PoE receivers, two power supplies may be required. Refer to
the following datasheet: https://www.downloads.netgear.com/les/GDC/datasheet/en/M4300.pdf
Summary
Version: 12.0.7.15
Ports 1 through 48 can be used to connect OmniStream devices.
Ports 49 through 52 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://192.168.1.254
VLAN 10: http://10.1.1.254
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 49 through 52
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 48
* DHCP range: 10.1.0.1 through 10.1.1.0
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.253 range with a
subnet mask of 255.255.254.0.
• DHCP lease time: 7 days
• Spanning tree mode: RSTP
• BPDU guard: Enabled
• IGMP (VLAN 10 only)
* Snooping: Enabled
OmniStream Certied Switches
* Immediate leave: Enabled
* Querier: Enabled
32
Page 33
Default Congurations
Instructions for uploading the conguration le for Netgear switches
1. Connect a computer directly to the switch using the out-of-band (OOB) interface.
2. In Windows, go to the command prompt, type ncpa.cpl, and press [ENTER]. This will display the network
properties for Windows.
3. Right-click on the adapter for the network switch and select Properties from the context menu.
4. Under the Ethernet Properties dialog box, click Internet Protocol Version 4 and then click the Properties
button.
5. Click the Use the following IP address radio button and enter an IP range between 192.168.0.1 through
192.168.0.254.
6. Set the Subnet mask eld to 255.255.255.0.
7. Click the OK button, then minimize the Network Connections window. This window will be used again, later in
the procedure.
8. Download the conguration le from the link on page 36 (M4300-28G-PoE+) or page 37 (M4300-52G-PoE+).
9. Open a web browser and enter the IP address of 192.168.0.239 to display the login screen.
10. Login using the default credentials:
Username: admin
Password: (leave blank)
OmniStream Certied Switches
33
Page 34
11. Click the Maintenance tab, at the top of the screen, then click the Upgrade tab.
Default Congurations
12. Click HTTP File Upgrade in the menu bar on the left side of the screen.
13. Click the File Type drop-down list and select Text Conguration.
OmniStream Certied Switches
34
Page 35
14. Click the Browse... button and select the conguration le to be uploaded.
Default Congurations
15. After the conguration le has been successfully uploaded, a message box will be displayed indicating that the
web interface redirect to the login page. Click OK to dismiss the message box.
16. Maximize the Network Connections window from Step 7, and click the Obtain an IP address automatically
radio button, then click OK to apply changes.
17. Disconnect the computer from the OOB interface of the switch and reconnect it to any interface on VLAN10.
18. Login to the network switch using the following credentials:
Ports 1 through 23 are to be used only for OmniStream.
Ports 24 through 28 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 24 through 28
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 23
* DHCP range: 10.1.0.1 through 10.1.0.254
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
• DHCP lease time: 7 days
• Spanning tree mode: Point-to-Point
• BPDU guard: Enabled
• IGMP (VLAN 10 only)
* Snooping: Enabled
* Immediate leave: Enabled
* Querier: Enabled
OmniStream Certied Switches
36
Page 37
Instructions for uploading the conguration le for the Pakedge S3L-24P
1. Download the Pakedge S3L-24P conguration le from the link on page 5.
2. Open a web browser and enter the IP address of the switch in the address bar.
3. Enter the login credentials. The following are the default login credentials:
Username: pakedge
Password: pakedges
4. Click Maintenance > Conguration at the top of the page.
Default Congurations
4. Select HTTP Restore from the Conguration drop-down list.
5. Click Choose File and select the Pakedge S3L-24P.conf le.
Ports 1 through 48 are to be used only for OmniStream.
Conguration Details
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 48
* Static routing: 10.10.8.1
NOTE: Ruckus switches use two types of images: 1. Switch Image 2. Router Image.
This conguration is based on the Switch image. Before applying this conguration, make sure that
the switch is running the Switch image.
Assumptions: This conguration is a at Layer 2 conguration. To route across multiple networks, a
router will be required. This conguration also assumes that there is an external DHCP server (home
router).
• VLAN 1
* Ports: 1 through 48
* DHCP range: N/A
• DHCP lease time: N/A
• Spanning tree mode: RSTP
• BPDU guard: Enabled
• Green Ethernet: Disabled
• Loop Protection: Enabled
• SSH: Enabled
• Telnet: Enabled
• IGMP
* Snooping: Enabled
* Unregistered ooding: Disabled
* Immediate leave: Enabled
* Querier: Enabled
OmniStream Certied Switches
38
Page 39
Instructions for uploading the conguration le for the Ruckus ICX 7150-48ZP
NOTE: By default, Ruckus switches do not have a static IP address, but can act as a DHCP client.
1. Download the Ruckus ICX 7150-48ZP conguration le from the link on page 5.
2. Open a console session to the switch.
3. Enter the en command at the command prompt.
4. Press [ENTER] then type conf t at the command prompt.
Default Congurations
5. Press [ENTER].
6. Open the conguration le in a text editor and copy-and-paste the contents of the conguration le into the
console window.
7. Type the wr mem command at the command prompt and press [ENTER].
OmniStream Certied Switches
39
Page 40
Default Congurations
8. Conguration is complete.
To access the switch, use the IP address 10.10.8.254 and login using the following credentials:
It should be noted that the only dierence between the ES-24-500W and ES-24-250W switch is the power
consumption. The conguration information for both switches is identical. Refer to the next page for instructions on
how to upload the conguration le to the switch.
Summary
Version: 1.8.1
Ports 1 through 22 are to be used only for OmniStream.
Ports 23 through 26 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 23 through 26
* Static routing: 192.168.1.1 (home router for Internet trac)
IMPORTANT: Ports 25 - 26, are SFP interfaces and intended for 1G transceivers.
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 22
* DHCP range: 10.1.0.1 through
10.1.1.0
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
It should be noted that the only dierence between the ES-48-500W and ES-48-750W switch is the power
consumption. The conguration information for both switches is identical. Refer to the next page for instructions on
how to upload the conguration le to the switch.
Summary
Version: 1.8.0
Ports 1 through 46 are to be used only for OmniStream.
Ports 47 through 52 are to be used for management and can be connected to another network, such as a router that
has Internet access.
Conguration Details
Once the conguration le has been uploaded, access the switch GUI using the following IP addresses:
VLAN1: http://192.168.1.254
VLAN10: http://10.1.1.254.
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 47 through 52
* Static routing: 192.168.1.1 (home router for Internet trac)
NOTE: DHCP is not enabled on VLAN 1. It is expected that these ports would be connected
to an external network with its own DHCP server, which must be using the 192.168.1.1 through
192.168.1.254 range to function properly with this conguration. If a dierent IP range is used, then
the switch conguration must be modied, accordingly.
• VLAN 10
* Ports: 1 through 46
* DHCP range: 10.1.0.1 through 10.1.1.0
NOTE: Static address assignments may be made in the 10.1.1.1 through 10.1.1.254 range with a
subnet mask of 255.255.254.0.
• DHCP lease time: 7 days
• Spanning tree mode: RSTP
• BPDU guard: Enabled
• IGMP (VLAN 10 only)
* Snooping: Enabled
OmniStream Certied Switches
* Immediate leave: Enabled
* Querier: Enabled
42
Page 43
Default Congurations
Instructions for uploading the conguration le for Ubiquiti switches
1. In Windows, go to the command prompt, type ncpa.cpl, and press [ENTER]. This will display the network
properties for Windows.
2. Right-click on the adapter for the network switch and select Properties from the context menu.
3. Under the Ethernet Properties dialog box, click Internet Protocol Version 4 and then click the Properties
button.
4. Click the Use the following IP address radio button and enter an IP address that is within the range of the
network switch. For example, if the switch is 192.168.1.2, then enter an IP address of 192.168.1.10.
5. Set the Subnet mask eld to 255.255.255.0.
6. Click the OK button, then minimize the Network Connections window. This window will be used again, later in
the procedure.
7. Download the conguration le from the link on page 25. Note that the conguration le is the same for both the
ES-48-500W and ES-48-750W.
8. Power on the switch. Once the switch is powered, it will attempt to locate a DHCP server to assign an
IP address. However, by default, if no DHCP server is found, it will be assigned the static IP address of
192.168.1.2.
9. Open a web browser and enter the IP address of the switch in the address bar and display the login screen.
10. Click the Go to the legacy interface link, under the SIGN IN button.
IMPORTANT: Do not enter login credentials on this screen. Switch to the legacy interface before
entering login credentials.
Click here
OmniStream Certied Switches
43
Page 44
Default Congurations
11. Enter the login credentials to access the user interface.
12. Enter the IP address of the switch in a web browser, login, and click System > Utilities > Transfer.
13. In the Transfer tab, click the Upload button in the HTTP row, highlighted below. Once this button is clicked,
the HTTP File Upload dialog will be displayed.
Upload button
OmniStream Certied Switches
44
Page 45
14. Click the File Type drop-down list and select Setup Conguration.
Default Congurations
15. Click the Choose File button to display the
Open File dialog box. Select the conguration
le that was downloaded in step 7.
16. Click the Open button to select the
conguration le.
17. Click the Begin Transfer button on the HTTP File Upload dialog. The upload sequence should only take a few
seconds.
18. Click Close to dismiss the HTTP File Upload dialog box.
19. Click System > Utilities > Restart Switch.
20. Click the Restart Without Core Dump button.
OmniStream Certied Switches
45
Page 46
Default Congurations
21. In Windows, return to the Network Connections window, which was minimized in step 9. If the window was
closed, go to the command prompt, type cpna.cpl, and press [ENTER] to restore the window.
22. Right-click on the adapter for the network switch and select Properties from the context menu.
23. Under the Ethernet Properties dialog box, click Internet Protocol Version 4 and then click the Properties
button.
24. Restore DHCP by clicking the Obtain an IP address automatically radio button.
25. Click OK to commit changes, then click OK on the Ethernet Properties dialog to dismiss it.
26. Go to the windows command prompt and check the IP of the network switch by executing the ipcong
command. Note that it may take a minute or so for the switch to complete the reboot procedure. Once the
switch is up and running, the DHCP IP address will be displayed.
Switch IP address
27. Enter the new IP address of the switch in a web browser window. In the example above, the IP address is
10.1.0.5.
28. Conguration is complete. Login to the switch using the following credentials:
Username: admin
Password: Atlona
OmniStream Certied Switches
46
Page 47
Network Switch Conguration
Before working with the OmniStream devices, the network switch must be set up. This section will provide
instructions for manually conguring two dierent switches: Araknis AN-310-SW-24-POE and Cisco SG350X-24MP.
Araknis AN-310-SW-24-POE
NOTE: Although this section specically shows images of the AN-310-SW-24-POE web interface,
the following instructions are applicable to all Araknis 8/16/24-port network switches with both front
and rear-facing ports. These switches default to an IP address of 192.168.20.254.
1. Connect the PC directly to any of the switch interfaces and congure the PC network adapter with a static IP
address within the same subnet. For example, if the default IP address of the switch is 192.168.20.254, then
assign the PC a static IP address in the range of 192.168.20.x (where x ≠ 254).
2. Launch the desired web browser and enter the IP address of the network switch into the address eld, then
press [ENTER].
3. Enter the username and password. The default login credentials are as follows:
Username: araknis
Password: araknis
4. The System Status page will be displayed.
5. Click Settings > System in the menu bar on the left. In the System Name eld, optionally change the default
hostname. Refer to the next page for illustration.
OmniStream Certied Switches
47
Page 48
Network Switch Conguration
Hostname
6. Enter the new administrator user name and password in the Admin Username and New Admin Password
elds, respectively. When changing the password, conrm the new password in the Conrm New Admin Password eld.
Username and Password fields
7. Click Settings > Access Management in the menu on the left side of the screen.
8. Click toggle switch, next to IP Address Settings, and set it to IPv4.
IP Address Settings toggle
9. Click the Static radio button, next to Auto Conguration.
10. Enter the following information in the IPv4 Address, Subnet Mask, and Default Gateway elds. This IP address
is used for management and the IGMP querier.
• IPv4 Address: 10.1.1.254
• Subnet Mask: 255.255.255.0
• Default Gateway: 10.1.1.1
11. Click Apply to commit changes. The switch will prompt to be set to the new IP address.
12. Update the network settings of the computer to use an IP address of 10.1.1.x (where x ≠ 254) and a subnet of
255.255.255.0.
OmniStream Certied Switches
48
Page 49
Network Switch Conguration
13. Click Settings > VLAN, in the menu on the left side of the screen.
14. Change the name of VLAN 1. By default, all interfaces are part of VLAN 1. Create additional VLANs as required.
15. Click Advanced > Multicast > IGMP Snooping.
16. Click the following radio buttons, under IGMP Snooping.
• Status: Enabled
• Report Supression: Enabled
• Unregistered IPMC Forward Action: Drop
17. Under VLAN Settings, click the IGMP Snooping Status drop-down list and select Enabled.
18. Click the Fast Leave drop-down list and select Enabled.
19. Under Querier Settings, click the Querier State drop-down list and select Enabled for VLAN1, then click Apply
to commit changes.
20. Locate the Querier Settings section and conrm that for VLAN ID 1, the following is true:
• Querier Status: Querier
• Querier IP: IP address should match the IPv4 address of the switch.
22. Click Advanced > STP > Global Settings.
23. Under Basic Settings, click the Priority drop-down list and select 4096.
24. Click Apply to commit changes.
25. Conguration is complete.
OmniStream Certied Switches
Priority drop-down list
49
Page 50
Network Switch Conguration
Cisco SG350X-24MP
IMPORTANT: The following is divided into ve sections. Each section must be followed in the order
listed below. Deviating from this order, or skipping steps within a section, may result in unpredictable
switch operation.
• Getting Started
• VLAN Setup
• IPv4 Interface Setup
• Setting IP Multicast
• Setting up User Accounts
Getting Started
1. Connect a PC or laptop to the network switch. It is best to you whichever port will remain on VLAN1 of the switch
to avoid the PC losing connection when settings are changed on the switch.
2. Go into the computer settings and change the IP of the PC to be on the same range as the switch.
NOTE: If the IP address of the network switch is 192.168.1.254, then the computer should be set
to 192.168.1.xx, where xx represents values from 1 to 253, as long as that IP address is not already
assigned on that network. The default IP address for all Cisco switches is 192.168.1.254/24.
3. Launch the desired web browser and enter the IP address of the network switch into the address eld, then
press [ENTER].
4. Enter the username and password. The default login credentials are as follows:
Username: cisco
Password: cisco
OmniStream Certied Switches
50
Page 51
Network Switch Conguration
5. Click the Login button.
The switch will most likely require a new password to be assigned, before going further. This step may vary
depending on the network switch. Enter the desired password, as required.
6. Click the Apply button to commit changes.
7. The Getting Started page will be displayed.
OmniStream Certied Switches
51
Page 52
Network Switch Conguration
VLAN Setup
8. Click the Display Mode drop-down list, near the upper-right hand corner of the screen, and select Advanced.
9. Select VLAN Management from the menu on the left side of the screen. The VLAN Management menu will
expand and the VLAN Settings page will be displayed. If the VLAN Setting page is not displayed, click VLAN Management > VLAN Setting to display the page.
By Default, VLAN 1 is active. If the network is self-contained, skip to 15. Otherwise, continue with the next step.
10. Click the Add... button. The Add VLAN dialog will be displayed. The purpose of creating a VLAN is to separate
a network into separate logical areas / broadcast domains. In this case, the VLAN is created to isolate AV-overIP trac from normal network trac.
OmniStream Certied Switches
52
Page 53
Network Switch Conguration
11. Enter the numerical ID of the VLAN in the VLAN ID eld. This value is required and must be within the range of 2
to 4094.
NOTE: VLAN 1 is the Cisco default VLAN. This VLAN can be used, but it cannot be modied or
deleted.
12. OPTIONAL: Enter a name for the VLAN in the VLAN Name eld. For example, the name of the VLAN could
be used to identify a department, within a company, which uses that broadcast domain. In this example,
“OmniStream” has been assigned as the name of VLAN 5.
13. Click the Apply button to commit changes. If the VLAN was successfully created, the dialog box will display a
“Success” message.
OmniStream Certied Switches
53
Page 54
Network Switch Conguration
14. Repeat steps 11 through 13 to create as many VLANs as needed. If no additional VLANs are required, click the
Close button to dismiss the Add VLAN dialog box.
15. Click Administration, in the left-hand menu bar and select File Operations. The File Operations page will be
displayed.
16. Click the Duplicate radio button, next to Operation Type.
17. Click the Apply button to commit changes.
OmniStream Certied Switches
54
Page 55
Network Switch Conguration
IPv4 Interface Setup
18. Click IP Conguration in the left-hand menu bar and select IPv4 Interface. The IPv4 Interface page will be
displayed.
19. Click the check box next to VLAN 1 (DHCP) and then click the Delete button.
OmniStream Certied Switches
55
Page 56
Network Switch Conguration
20. Check the IP settings for VLAN 1. If no changes are required, continue with Step 4. However, if a dierent IP
address or subnet mask need to be specied, then follow the steps below:
a. Click the check box next to VLAN 1.
b. Click the Edit button.
c. The Edit IP Interface dialog will be displayed.
d. Make make the required changes, then click the Apply button to commit changes.
e. Click the Close button to dismiss the Edit IP Interface dialog box.
OmniStream Certied Switches
56
Page 57
Network Switch Conguration
21. Click the Add... button. The Add IP Interface dialog box will be displayed.
22. Click the VLAN radio button, then click the drop-down list to select the VLAN that was created under VLAN
Setup (page 52).
23. Click the Static IP Address radio button.
NOTE: It is recommended that a static IP address be assigned to a VLAN, to avoid IP changes.
24. Enter the IP address of the VLAN, in the IP Address eld. In the example below, 10.1.1.254 is used. However,
any available IP address in the pool may be used.
25. Click the Network Mask radio button and enter the subnet mask. In this example, 255.255.254.0 is used.
However, depending upon the requirements, any valid network mask may be used.
26. Click the Apply button to commit changes. Repeat Steps 4 through 9 for each additional VLAN, as necessary.
27. After all VLANs have been set up, click the Close button to dismiss the Add IP Interface dialog box.
28. Click Administration > File Operations in the menu bar on the left side of the screen. The File Operations
page will be displayed.
29. Click the Duplicate radio button, next to Operation Type. Refer to the next page for more information.
OmniStream Certied Switches
57
Page 58
Network Switch Conguration
30. Click the Apply button to commit changes.
OmniStream Certied Switches
58
Page 59
Network Switch Conguration
Conguring IP Multicast
31. Click Port to VLAN from the VLAN Management menu. By default, the Membership Type, for each physical
port (interface), is assigned as Untagged.
32. Click the VLAN ID equals to drop-down list and select the VLAN ID that was created under VLAN Setup (page
52).
33. Leave the AND Interface Type equals to drop-down list as Port of Unit 1. Click the Go button.
OmniStream Certied Switches
59
Page 60
Network Switch Conguration
34. The Membership Type, for the VLAN, will automatically be assigned as Excluded for each physical port on the
switch.
35. Determine which physical ports will use the selected VLAN. Click the Membership Type drop-down list for each
physical port that will use the VLAN, and set its value to Untagged. For example, if physical ports 6 and 7 will be
used for VLAN 5, then set the Membership Type for these two ports to Untagged.
36. Scroll to the bottom of the list of ports and click the Apply button. Success messages will appear at the top and
bottom right of the screen.
NOTE: If the port the PC is connect to is move o VLAN1, then it will need to be set to the IP settings of the
new VLAN to continue.
OmniStream Certied Switches
60
Page 61
Network Switch Conguration
37. Click Multicast from the menu bar on the left side of the screen. The Properties window will automatically be
displayed.
38. Click the Enable box, next to Bridge Multicast Filtering Status, to enable this feature.
39. Click the IP Group Address radio button, under both Forwarding Method for IPv6 and Forwarding Method for IPv4.
40. Click the Apply button to commit changes.
41. Repeat steps 38 and 39 for each VLAN.
42. Click IGMP Snooping, under IPv4 Multicast Conguration, from the menu bar on the left side of the screen.
OmniStream Certied Switches
61
Page 62
Network Switch Conguration
43. Click the check box next to IGMP Snooping, to enable this feature.
44. Click the Apply button to commit changes.
45. Click the radio button next to VLAN 1, as shown below, in the IGMP Snooping Table.
46. Click the Edit... button to display the Edit IGMP Snooping Settings dialog box.
OmniStream Certied Switches
62
Page 63
Network Switch Conguration
47. Click the Enable checkboxes next to IGMP Snooping Status, Immediate Leave, and IGMP Querier Status.
Make sure each of these checkboxes display a checkmark. Leave the rest of the settings as they are.
48. Click the Apply button to commit changes.
49. Click the VLAN ID drop-down list, and select the next VLAN ID number. Repeat steps 17 and 18 for each VLAN
that was created.
50. Click the Close button to dismiss the Edit IGMP Snooping Settings dialog.
51. Click Administration > File Operations in the menu bar on the left side of the screen. The File Operations
page will be displayed.
52. Click the Duplicate radio button, next to Operation Type, then click the Apply button to commit changes.
OmniStream Certied Switches
63
Page 64
Network Switch Conguration
53. Click Unregistered Multicast from the Multicast menu on the left side of the screen. By default, all physical
ports will have port forwarding enabled, as shown below.
54. Click the Filtering radio button to assign port ltering to each port.
55. Click the Apply button to commit changes.
56. Click Administration > File Operations in the menu bar on the left side of the screen. The File Operations
page will be displayed.
57. Click the Duplicate radio button, next to Operation Type, then click the Apply button to commit changes.
OmniStream Certied Switches
64
Page 65
Network Switch Conguration
Creating User Accounts
This next section is optional, and provides instructions on creating user accounts. This is only required if multiple
users will need access to the network switch.
1. Click User Accounts from the Administration menu.
2. Click the Add... button to display the Add User Account dialog box.
3. Enter the desired username and password in the User Name and Password elds, respectively. Conrm the
password by re-entering it in the Conrm Password eld.
4. Click the Read/Write Management Access radio button, then click the Apply button to commit changes.
5. Repeat steps 2 through 4, as required, for each user.
6. Click the Close button to dismiss the Add User Account dialog box and click Yes when prompted to save
changes.
OmniStream Certied Switches
65
Page 66
Network Switch Conguration
7. Click Administration > File Operations in the menu bar on the left side of the screen. The File Operations
page will be displayed.
8. Click the Duplicate radio button, next to Operation Type.
9. Click the Apply button to commit changes.
10. Switch conguration is complete.
OmniStream Certied Switches
66
Page 67
Appendix
Troubleshooting
S3L-24P Pakedge Switch Isn’t Passing Multicast
SKU: S3L-24P
Challenge: The loaded Atlona default conguration le for the S3L-24P Package switch does not pass
OmniStream multicast as expected.
Details: The switch is not accepting the VLAN 10 IP interface using the provided conguration. The IGMP
Snooping mechanism won’t work as expected without the VLAN 10 IP address. The VLAN 10
default IP address (in case you are loading the Atlona default conguration le) is 10.1.1.254 with
a subnet mask of 255.255.254.0. To complete the switch conguration and begin using
OmniStream, follow the procedure below: