PANDUIT® oers high performance adhesive backed mounts and devices for a quick, dependable method
of securing, routing and protecting wires or cables. The adhesive backing provides easy installation and is
an alternative to mechanical fasteners. When properly installed, PANDUIT® Adhesive Backed Mounts and
devices oer the advantage of lower installed cost and high reliability.
PANDUIT® Adhesive Backed
Mounts and Devices
Features and Benets
■
Superior adhesive for long term reliability
■
2-up mount conguration speeds liner removal and installation
■
4-way cable tie entry makes part orientation fast and easy
■
Adhesive backing allows routing of wires and cables where mounting
holes cannot be drilled
■
Mount sizes range from .50" x .50" to 2.00" x 2.00" for space limited or
heavy load applications
■
UL Recognized
■
Used with PANDUIT® cable ties for a complete wire routing solution
■
One piece solutions lower inventory costs and speed installation
■
Cable tie entry ramps guide the cable tie into the mount
■
Bevel entry on wire clips speeds installation
■
Releasable latches allow addition or removal of cables
Selection of Adhesive
Choose from three types of adhesive systems designed for specic application environments and temperatures: Rubber-based
Adhesive Foam Tape, Acrylic-based Adhesive Foam Tape, or Two-part Epoxy Adhesive. Carefully choosing the correct adhesive
and closely following the recommended installation steps will provide a reliable, long-term bond.
Rubber-Based Adhesive Foam Tape
Rubber-based Adhesive Foam Tape is the best choice for the vast majority of adhesive mount applications, including applica-
tions where powder coated surfaces are being used. This pressure sensitive tape develops its strength extremely fast and can be
used in indoor environments with temperatures ranging from -20°F to 120°F (-29°C to 49°C). Rubber-based Adhesive Foam Tape
is the most widely used and generally recommended foam tape for wire routing applications.
Acrylic-Based Adhesive Foam Tape
Acrylic-based Adhesive Foam Tape is a good choice in applications with prolonged exposure to UV rays or heavy moisture. It is
designed to be used in indoor or outdoor environments where temperatures can vary from -20°F to 180°F (-29°C to 82°C). The
acrylic-based adhesive develops its maximum strength over a longer period of time compared to the rubber-based adhesive. It is
recommended that the mounts dwell eight (8) hours after installation and prior to loading.
Two-Part Epoxy Adhesive
Two-part Epoxy Adhesive is for use in applications where excessive loading is required or where the mounting surface is porous
rather than smooth. This adhesive is formulated specically for use on PANDUIT ® EMS and ASMS mounts in either indoor or
outdoor applications. It is packaged in convenient pre-measured cups to insure the proper ratio of resin and hardener, as well as
eliminate waste.
Adhesive Backed Mounts and Devices
Selection and Application Guide
Quick — Dependable — Secure
2
PANDUIT® oers high performance adhesive backed mounts and devices for a quick, dependable method
of securing, routing and protecting wires or cables. The adhesive backing provides easy installation and is
an alternative to mechanical fasteners. When properly installed, PANDUIT® Adhesive Backed Mounts and
devices oer the advantage of lower installed cost and high reliability.
PANDUIT® Adhesive Backed
Mounts and Devices
Features and Benets
■
Superior adhesive for long term reliability
■
2-up mount conguration speeds liner removal and installation
■
4-way cable tie entry makes part orientation fast and easy
■
Adhesive backing allows routing of wires and cables where mounting
holes cannot be drilled
■
Mount sizes range from .50" x .50" to 2.00" x 2.00" for space limited
or heavy load applications
■
UL Recognized
■
Used with PANDUIT® cable ties for a complete wire routing solution
■
One piece solutions lower inventory costs and speed installation
■
Cable tie entry ramps guide the cable tie into the mount
■
Bevel entry on wire clips speeds installation
■
Releasable latches allow addition or removal of cables
Selection of Adhesive
Choose from three types of adhesive systems designed for specic application environments and temperatures: Rubber-based
Adhesive Foam Tape, Acrylic-based Adhesive Foam Tape, or Two-part Epoxy Adhesive. Carefully choosing the correct adhesive
and closely following the recommended installation steps will provide a reliable, long-term bond.
Rubber-Based Adhesive Foam Tape
Rubber-based Adhesive Foam Tape is the best choice for the vast majority of adhesive mount applications, including
applications where powder coated surfaces are being used. This pressure sensitive tape develops its strength extremely fast and
can be used in indoor environments with temperatures ranging from -20°F to 120°F (-29°C to 49°C). Rubber-based Adhesive
Foam Tape is the most widely used and generally recommended foam tape for wire routing applications.
Acrylic-Based Adhesive Foam Tape
Acrylic-based Adhesive Foam Tape is a good choice in applications with prolonged exposure to UV rays or heavy moisture. It is
designed to be used in indoor or outdoor environments where temperatures can vary from -20°F to 180°F (-29°C to 82°C). The
acrylic-based adhesive develops its maximum strength over a longer period of time compared to the rubber-based adhesive.
It is recommended that the mounts dwell eight (8) hours after installation and prior to loading.
Two-Part Epoxy Adhesive
Two-part Epoxy Adhesive is for use in applications where excessive loading is required or where the mounting surface is porous
rather than smooth. This adhesive is formulated specically for use on PANDUIT ® EMS and ASMS mounts in either indoor or
outdoor applications. It is packaged in convenient pre-measured cups to insure the proper ratio of resin and hardener, as well
as eliminate waste.
2
Guideline for Adhesive
The following chart should be used as a guideline for choosing
the best adhesive for common surfaces and chemical resistance.
Since each application has specific requirements,
recommends that further testing be conducted to determine the
suitability of the adhesive in a specific environment or application.
PANDUIT
Surfaces
Rubber Based Foam
Tape Mounts
Acrylic Based Foam
Tape Mounts
Epoxy Applied
Adhesive Mounts
Plastics Good Good Good
Wood Good Good Good
Glass Fair Good Good
Painted Surfaces Good Good Fair
Powder Coating Good Fair Good
Metal Good
1
Good
1
Good
Paper Good Good Fair
Concrete, Stone, Masonry Not Recommended Not Recommended Good
Chemical Resistance
Water Good Poor Poor
Oil Poor Fair
Gasoline Poor Fair
Dilute Acids Poor Fair
Dilute Alkalis Good Fair
Organic Solvents Poor Fair
Outdoor Exposure Not Recommended Good
1. Not recommended for use on copper or brass.
2. Mounts manufactured from outdoor material only. For specific applications, individual testing prior to extensive use is suggested.
3. Depends on concentration, exposure time and chemical composition.
3
3
3
3
3
2
Good
Fair
Fair
Fair
Not Recommended
2
Good
3
Proper Installation Steps
Surface Preparation
For best results, mounts should be applied to a clean, dry, and grease-free surface. It is recommended that for each individual application,
a solvent or cleanser be used to thoroughly prepare the surface for mount installation. The following are recommended cleaning guidelines:
1. For Rubber and Acrylic-based Adhesive Foam Tape, a mixture of water and isopropyl alcohol may be used on
Alcohol
Installing the Mount
most surfaces.
For Two-part Epoxy Adhesive, especially on masonry surfaces, be sure to clean all loose particles away before
mount installation. Some surface abrasion is recommended on smooth surfaces to achieve maximum strength.
A light rubbing with medium grit emery cloth or sandpaper is best. Wash the surface after abrading.
2. Allow the surface to dry completely before applying the mount.
1. For proper installation of adhesive backed mounts with foam tape, remove the release liner from the foam
adhesive. Without touching the adhesive, place the mount in the desired location.
For Two-part Epoxy Adhesive Mounts, apply 1/3 of the mixed adhesive to the bottom of the
PANDUIT
®
EMS or
ASMS mount. Without touching the adhesive, place the mount in the desired location.
2. Apply firm pressure for five (5) seconds to the foam tape mounts to insure proper adhesion.
Two-part Epoxy Adhesive Mounts should be twisted in place to ensure the adhesive is forced into the
porous surface.
3. Allow the mount to remain in place for the recommended dwell time for the specific adhesive being used.
12
3
9
6
The dwell time for Rubber-based Adhesive Foam Tape is two (2) hours and for Acrylic-based Adhesive Foam
Tape it is eight (8) hours.
Two-part Epoxy Adhesive Mounts can support about 5 lbs. after first fifteen (15) minutes. The adhesive fully
cures after twenty-four (24) hours and bonding strength will exceed 50 lbs.
4. The mount is now ready to be used.
4
Mount Spacing
To determine the number of mounts to use in a given application, the following formula can be used as a guideline:
Cable bundle weight in lbs/foot
Maximum static load rating of the mount*
Minimum number of
=
mounts per foot
For example, to determine the mount spacing using part number ABM2S-A-C for an application with a bundle of wires that weigh one
pound per foot, the formula would be:
1 pound per foot
=
0.5 lbs load rating
* See pages 6-7 for static load ratings.
2 mounts per foot
Proper Storage Conditions
Mounts and adhesives should be kept in the original packaging until they are ready to be applied. Store at room temperature 70°F (21°C)
with 45% or less relative humidity. Avoid storing adhesive products near heating vents or other heating sources.
Using the guidelines above, the average shelf life of adhesive foam tape is three (3) years from the date of manufacture. The shelf life of
Two-part Epoxy Adhesive is one (1) year from the date of manufacture. Failing to follow the recommended storage conditions may reduce
the shelf life or adhesive strength of the foam tape and Two-part Epoxy Adhesive.
Adhesive Technical Information
Adhesive foam tape properties are developed with thorough laboratory research and testing. The double-coated adhesive foam tape used
on
PANDUIT
performance for use on adhesive mounts. Each package of mounts has an expiration date and a Quality Control number printed on the
label, which permit traceability.
Double Coated Foam Tape Properties
Backing Material
Nominal Backing Density (pcf)
Thickness (PSTC-33)
Static Shear MIL-T-60394A (Hours)
®
Adhesive Backed Mounts is manufactured under strict quality requirements, which provide consistent, high quality
(In.) Total
Less Liner
72°F/17.6 psi
72°F/8.8 psi
158°F/2.s psi
Rubber Adhesive
Polyethylene
6
.040
.035
500+
1000+
100+
Acrylic Adhesive
Polyethylene
6
.039
.034
N/A
N/A
200+
5
Adhesive Backed Mounts and Clips
Adhesive Backed Mounts and Clips
Part Number Material
Length Width Max. Static Load
Adhesive Type
Std.
Pkg.
Qty.‡In. mm In. mm Lbs. g
4-Way Adhesive Backed Mounts
ABM1M-A-C Nylon 6.6 .50 12.7 .50 12.7 .13 59 Rubber 100
ABMM-A-C ABS .75 19.1 .75 19.1 .30 136 Rubber 100
ABM2S-A-C ABS 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM100-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM112-A-C Nylon 6.6 1.12 28.6 1.12 28.6 .63 286 Rubber 100
ABM3H-A-L Nylon 6.6 1.50 38.1 1.50 38.1
1.13 513
Rubber 50
ABM4H-A-L Nylon 6.6 2.00 50.8 2.00 50.8
1.13 513
Rubber 50
T
AK-TY
®
Hook & Loop Cable Tie Mounts
ABMT-A-C Nylon 6.6 1.10 28.7 1.10 28.6 .38 174 Rubber 100
ABMT-A-C20 Nylon 6.6
1.12 28.5 1.12 28.5
.38 174 Rubber 100
Length Width Max. Static Load
Part Number Material
4-Way Adhesive Backed Mounts
ABM
ABMT
SMS
ARC
ABM1M-A-C
ABMM-A-C
ABM2S-A-C
ABM100-A-C
ABM112-A-C Nylon
ABM3H-A-L
ABM4H-A-L
ABMT-A-C
ABMT-A-C20
T
AK-TY
®
Hook & Loop Cable Tie Mounts
Snap-In Cable Tie Mount
SMS-A-C
C
LINCHER
ARC.68-A-Q
™
Adjustable Releasable Clamp
Adhesive Backed Cord Clips
ACC19-A-C Nylon
ACC38-A-C
ACC62-A-C Nylon
Nylon 6.6 .50 12.7 .50 12.7 .13 59 Rubber 100
ABS .75 19.1 .75 19.1 .30 136 Rubber 100
ABS 1.00 25.4 1.00 25.4 .50 227 Rubber 100
Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
6.6 1.1
Nylon 6.6 1.50 38.1 1.50 38.1
Nylon 6.6 2.00 50.8 2.00 50.8
Nylon 6.6 1.10 28.7 1.10 28.6 .38 174 Rubber 100
Nylon 6.6
ABS 2.00 50.8 1.00 25.4 1.00 454 Rubber 100
Polypropylene 1.00 25.4 1.00 25.4 .50 227 Rubber 25
6.6 .63
Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
6 1.25 31.7 1.12 28.6 .70 318 Rubber 100
6.
2 28.6 1.12 28.6 .63 286 Rubber 100
1.12 28.5 1.12 28.5
16.0 .76 19.3 .20 91 Rubber 100
1.13 513
1.13 513
.38 174 Rubber 100
“J” Clips
ACC
AJC
A1C
A2C
AJC12-A-C
AJC19-A-C
AJC31-A-C
AJC38-A-C
A1C Type Clips
A1C12-A-C8
A1C25-A-C8
A1C38-A-C8
A1C50-A-C8
A2C Type Clips
A2C12-A-C8
A2C25-A-C8
A2C38-A-C8
A2C50-A-C8
PVC 1.00 25.4 .86 21.8 .40 182 Rubber 100
PVC 1.25 31.8
PVC 1.75 44.5
PVC 2.00 50.8
PVC .77 19.6 .63 16.0 .14 64 Rubber 100
PVC .91 23.1 .63 16.0 .14 64 Rubber 100
PVC 1.04 26.4 .63 16.0 .14 64 Rubber 100
PVC 1.17 29.7 .63 16.0 .14 64 Rubber 100
PVC 1.30 33.0 .63 16.0 .14 64 Rubber 100
PVC 1.43 36.3 .63 16.0 .14 64 Rubber 100
PVC 1.56 39.6 .63 16.0 .14 64 Rubber 100
PVC 1.68 42.7 .63 16.0 .14 64 Rubber 100
.87 22.1
1.22 31.0
1.27 32.3
.50 227 Rubber 100
.90 408 Rubber 100
1.00 454 Rubber 100
Metal Adhesive Backed Cord Clips
MACC25-A-C
MACC62-A-C
Zinc Plated Steel
Zinc Plated Steel 1.18 30.0
.77 19.6 .54 13.7
.78 19.8
.21 95 Rubber 100
.44 200 Rubber 100
Latching Wire Clips
MACC
LWC
LWC19-A-C
LWC25-A-C
LWC38-A-C
LWC50-A-L
LWC75-A-L
LWC100-A-L
Contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com.
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
Nylon 6.6 .85 21.6 .61 15.5 .25 113 Rubber 100
Nylon 6.6 .88
Nylon 6.6
Nylon 6.6 1.26 32.0 1.00 25.4 .63 272 Rubber 50
Nylon 6.6 1.48 37.6 1.24 31.5 .93 417 Rubber 50
Nylon 6.6 2.21 56.1 1.97 50.0 2.25 1020 Rubber 50
.88 22.4
22.4
1.00 25.4 .45 204 Rubber 100
1.00 25.4 .50 227 Rubber 100
Adhesive Type
Rubber 50
Rubber 50
Std.
Pkg.
Qty.‡In. mm In. mm Lbs. g
6
Adhesive Backed Mounts and Clips (continued)
Adhesive Backed Mounts and Clips (continued)
gLbs.mmIn.mmIn.
Std.
Pkg.
Qty.‡
Adhesive Type
Max. Static Load Width Length
MaterialPart Number
Bevel Entry Clips
BEC38-A-L Nylon 6.6 1.46 37.1 1.24 31.5 .91 411 Rubber 50
Max. Static Load Width Length
BEC
VCC
LC
Bevel Entry Clips
BEC38-A-L
BEC75-A-L
Vertical Cord Clip
VCC25-A-C
Adhesive Backed Latching Clips
LC3-A-C8 PVC
LC5-A-C8
LC10-A-L8
MaterialPart Number
Nylon 6.6 1.46 37.1 1.24 31.5 .91 411 Rubber 50
38.4
.78 19.8
1.00 25.4 .60 272 Rubber 50
.28 127 Rubber 100
Nylon 6.6 1.46 37.1 1.49 37.8 1.09 493 Rubber 50
Nylon 6.6 1.00 25.4 .50 12.7 .25 113 Rubber 100
.75 19.0
PVC 1.01 25.7 1.00 25.4 .50 227 Rubber 100
PVC 1.51
gLbs.mmIn.mmIn.
Low Profile Flat Cable Mounts
2.56 65.0 .50 12.7 .25 113 Rubber 100
LPFCM
LPFCM14-A-C14 Nylon
LPFCM22-A-C14
LPFCM34-A-C14
Nylon 6.6 3.31 84.0 .50 12.7 .25 113 Rubber 100
Nylon 6.6 4.56 115.8 .50 12.7 .25 113 Rubber 100
6.6
Latching Flat Cable Mounts
.6 1.21 30.7 1.00 25.4 .50 227 Rubber 100
6
Nylon 6.6 1.37 34.8 1.00 25.4
Nylon 6.6 2.22 56.3 1.00 25.4 1.00 454 Rubber 100
Nylon 6.6 3.38 85.9 1.00 25.4 1.50 681 Rubber 50
.685 311
FCM
FCM1-A-C14 Nylon
FCM1.2-A-C14
FCM2-A-C14
FCM3.25-A-L14
Cable Holder – Adhesive Backed
CH105-A-C14 Nylon
6.6
2.50 63.0 2.06 52.0 1.28 581 Rubber 100
Latching Flat Cable Holder
CH
FCH2-A-C14 Nylon
6.6 2.50 63.5 1.03 26.2
1.07 486
Flat Cable Clips
FCH2
FCC-A-C8
FCC5-A-C8
Contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com.
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
PVC 1.00 25.4 1.09 27.7 .50 227 Rubber 100
PVC 1.00 25.4
.59 14.8
.25
117
Adhesive Type
Rubber 100
Rubber 100
Rubber 100
Std.
Pkg.
Qty.‡
FCC
ASMS
EMS
EMS KITS
Epoxy Applied Mounts
Length Width Max. Static Load
Part Number Material
ASMS-A-X
EMS-A-C
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
Aluminum Base/Nylon Mount 1.13 28.6 1.13 28.6 10.00 4540 EMA Epoxy 10
Nylon 6.6 1.00 25.4 1.00 25.4 10.00 4540 EMA Epoxy 100
Adhesive Type
Std.
Pkg.
Qty.‡In. mm In. mm Lbs. g
Epoxy Applied Mount Kits
Std.
Pkg.
Qty.‡
Part Number Color Environment
Used With
Cable Ties
Number of
Cable Ties
Number of
EMS Mounts
Number of
Epoxy Cups
Number of
Mixer Sticks
Epoxy Adhesive Only
EMA-X Gra
y Indoors/Outdoors –– — — 10 10 10
Epoxy Mounting Kit with EMS Mounts
EMSK3-1-X0 Black Indoors/Out
doors M, I, S — 3 1 1 10
Epoxy Mounting Kit with EMS Mounts and Cable Ties
EMSK3-1-3-0 Black Indoors/Outdoors M, I, S
EMSK12-4-12-X0 Black Indoors/Outdoors M, I, S 3 PLT2S-0 12 4 4 10
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
3 PLT2S-0 3 1 1 1
7
Loading...