Panduit ABM1M-A-C Application Guide

PANDUIT® oers high performance adhesive backed mounts and devices for a quick, dependable method
of securing, routing and protecting wires or cables. The adhesive backing provides easy installation and is an alternative to mechanical fasteners. When properly installed, PANDUIT® Adhesive Backed Mounts and devices oer the advantage of lower installed cost and high reliability.
PANDUIT® Adhesive Backed Mounts and Devices
Features and Benets
Superior adhesive for long term reliability
2-up mount conguration speeds liner removal and installation
4-way cable tie entry makes part orientation fast and easy
Adhesive backing allows routing of wires and cables where mounting
holes cannot be drilled
Mount sizes range from .50" x .50" to 2.00" x 2.00" for space limited or
heavy load applications
UL Recognized
Used with PANDUIT® cable ties for a complete wire routing solution
One piece solutions lower inventory costs and speed installation
Cable tie entry ramps guide the cable tie into the mount
Bevel entry on wire clips speeds installation
Releasable latches allow addition or removal of cables
Selection of Adhesive
Choose from three types of adhesive systems designed for specic application environments and temperatures: Rubber-based Adhesive Foam Tape, Acrylic-based Adhesive Foam Tape, or Two-part Epoxy Adhesive. Carefully choosing the correct adhesive and closely following the recommended installation steps will provide a reliable, long-term bond.
Rubber-Based Adhesive Foam Tape
Rubber-based Adhesive Foam Tape is the best choice for the vast majority of adhesive mount applications, including applica- tions where powder coated surfaces are being used. This pressure sensitive tape develops its strength extremely fast and can be used in indoor environments with temperatures ranging from -20°F to 120°F (-29°C to 49°C). Rubber-based Adhesive Foam Tape is the most widely used and generally recommended foam tape for wire routing applications.
Acrylic-Based Adhesive Foam Tape
Acrylic-based Adhesive Foam Tape is a good choice in applications with prolonged exposure to UV rays or heavy moisture. It is designed to be used in indoor or outdoor environments where temperatures can vary from -20°F to 180°F (-29°C to 82°C). The acrylic-based adhesive develops its maximum strength over a longer period of time compared to the rubber-based adhesive. It is recommended that the mounts dwell eight (8) hours after installation and prior to loading.
Two-Part Epoxy Adhesive
Two-part Epoxy Adhesive is for use in applications where excessive loading is required or where the mounting surface is porous rather than smooth. This adhesive is formulated specically for use on PANDUIT ® EMS and ASMS mounts in either indoor or outdoor applications. It is packaged in convenient pre-measured cups to insure the proper ratio of resin and hardener, as well as eliminate waste.
Adhesive Backed Mounts and Devices Selection and Application Guide
Quick — Dependable — Secure
2
PANDUIT® oers high performance adhesive backed mounts and devices for a quick, dependable method
of securing, routing and protecting wires or cables. The adhesive backing provides easy installation and is an alternative to mechanical fasteners. When properly installed, PANDUIT® Adhesive Backed Mounts and devices oer the advantage of lower installed cost and high reliability.
PANDUIT® Adhesive Backed Mounts and Devices
Features and Benets
Superior adhesive for long term reliability
2-up mount conguration speeds liner removal and installation
4-way cable tie entry makes part orientation fast and easy
Adhesive backing allows routing of wires and cables where mounting
holes cannot be drilled
Mount sizes range from .50" x .50" to 2.00" x 2.00" for space limited
or heavy load applications
Select Mounts, Clamps and Clips are UL Recognized
Used with PANDUIT® cable ties for a complete wire routing solution
One piece solutions lower inventory costs and speed installation
Cable tie entry ramps guide the cable tie into the mount
Bevel entry on wire clips speeds installation
Releasable latches allow addition or removal of cables
Guideline for Adhesive
The following chart should be used as a guideline for choosing the best adhesive for common surfaces and chemical resistance. Since each application has specific requirements, recommends that further testing be conducted to determine the suitability of the adhesive in a specific environment or application.
PANDUIT
Selection of Adhesive
Choose from four types of adhesive systems designed for specic application environments and temperatures: Rubber-based, Acrylic­based, and High Bond Acrylic-based Adhesive Foam Tape, or Two-part Epoxy Adhesive. Carefully choosing the correct adhesive and closely following the recommended installation steps will provide a reliable, long-term bond.
Rubber-Based Adhesive Foam Tape
Rubber-based Adhesive Foam Tape is the best choice for the vast majority of adhesive mount applications, including applications where powder coated surfaces are being used. It has a static load rating of 1/2 pound per square inch. This adhesive tape is suitable only for indoor use application, but the tape has a temperature performance tolerance range of -20° F to 120° F (-29° C to 49° C). It is recommended that rubber-based adhesive mounts dwell two (2) hours after installation, prior to loading. Rubber-based Adhesive Foam Tape is the most widely used and generally recommended foam tape for wire routing applications.
Acrylic-Based Adhesive Foam Tape
Acrylic-based Adhesive Foam Tape is a good choice in applications with prolonged exposure to UV rays or heavy moisture. It has a static load rating of 1/2 pound per square inch, and is suitable for both indoor and outdoor applications. This tape has a temperature performance tolerance range of -20° F to 180° F (-29° C to 82° C). The acrylic-based adhesive develops its maximum strength over a longer period of time compared to the rubber-based adhesive. It is recommended that the mounts dwell eight (8) hours after installation and prior to loading.
High Bond Acrylic-Based Adhesive Foam Tape
High bond Acrylic-Based Adhesive Foam Tape is a good choice in applications with prolonged exposure to UV rays or heavy moisture and where additional tack strength is needed. It has a static load rating of 1 pound per square inch, and is suitable for both indoor and outdoor applications. This tape has a temperature performance tolerance range of -31 F to 200 F (-35 C to 93 C). As it is acrylic-based, it develops its maximum strength over a longer period of time compared to the rubber-based adhesive. It is recommended that the mounts dwell eight (8) hours after installation prior to loading. This is a good choice for applications where wire routing is subjected to higher dynamic loads, such as those routed inside control panel access doors.
Surfaces
Plastics Good Good Good
Wood Good Good Good
Glass Fair Good Good
Painted Surfaces Good Good Fair
Powder Coating Good Fair Good
Metal Good
Paper Good Good Fair
Concrete, Stone, Masonry Not Recommended Not Recommended Good
Chemical Resistance
Water Good Poor Poor
Oil Poor Fair
Gasoline Poor Fair
Dilute Acids Poor Fair
Dilute Alkalis Good Fair
Organic Solvents Poor Fair
Outdoor Exposure Not Recommended Good
1. Not recommended for use on copper or brass.
2. Mounts manufactured from outdoor material only. For specific applications, individual testing prior to extensive use is suggested.
3. Depends on concentration, exposure time and chemical composition.
Rubber Based Foam
Tape Mounts
1
Acrylic Based Foam
Tape Mounts
1
Good
3
3
3
3
3
2
Epoxy Applied
Adhesive Mounts
Good
Good
Fair
Fair
Fair
Not Recommended
2
Good
Two-Part Epoxy Adhesive
Two-part Epoxy Adhesive is for use in applications where excessive loading is required or where the mounting surface is porous rather than smooth. This adhesive is formulated specically for use on PANDUIT applications. It is packaged in convenient pre-measured cups to insure the proper ratio of resin and hardener, as well as eliminate waste.
2
®
EMS and ASMS mounts in either indoor or outdoor
3
Proper Installation Steps
Surface Preparation
For best results, mounts should be applied to a clean, dry, and grease-free surface. It is recommended that for each individual application, a solvent or cleanser be used to thoroughly prepare the surface for mount installation. The following are recommended cleaning guidelines:
1. For Rubber and Acrylic-based Adhesive Foam Tape, a mixture of water and isopropyl alcohol may be used on
Alcohol
most surfaces. For Two-part Epoxy Adhesive, especially on masonry surfaces, be sure to clean all loose particles away before
mount installation. Some surface abrasion is recommended on smooth surfaces to achieve maximum strength. A light rubbing with medium grit emery cloth or sandpaper is best. Wash the surface after abrading.
Mount Spacing
To determine the number of mounts to use in a given application, the following formula can be used as a guideline:
Cable bundle weight in lbs/foot
Maximum static load rating of the mount*
For example, to determine the mount spacing using part number ABM2S-A-C for an application with a bundle of wires that weigh one pound per foot, the formula would be:
1 pound per foot
=
0.5 lbs load rating
2 mounts per foot
Minimum number of
=
mounts per foot
2. Allow the surface to dry completely before applying the mount.
Installing the Mount
1. For proper installation of adhesive backed mounts with foam tape, remove the release liner from the foam adhesive. Without touching the adhesive, place the mount in the desired location.
For Two-part Epoxy Adhesive Mounts, apply 1/3 of the mixed adhesive to the bottom of the ASMS mount. Without touching the adhesive, place the mount in the desired location.
2. Apply firm pressure for five (5) seconds to the foam tape mounts to insure proper adhesion. Two-part Epoxy Adhesive Mounts should be twisted in place to ensure the adhesive is forced into the
porous surface.
3. Allow the mount to remain in place for the recommended dwell time for the specific adhesive being used.
12
3
9
6
The dwell time for Rubber-based Adhesive Foam Tape is two (2) hours and for Acrylic-based Adhesive Foam Tape it is eight (8) hours.
Two-part Epoxy Adhesive Mounts can support about 5 lbs. after first fifteen (15) minutes. The adhesive fully cures after twenty-four (24) hours and bonding strength will exceed 50 lbs.
4. The mount is now ready to be used.
PANDUIT
®
EMS or
* See pages 6-7 for static load ratings.
Proper Storage Conditions
Mounts and adhesives should be kept in the original packaging until they are ready to be applied. Store at room temperature 70°F (21°C) with 45% or less relative humidity. Avoid storing adhesive products near heating vents or other heating sources.
Using the guidelines above, the average shelf life of adhesive foam tape is three (3) years from the date of manufacture. The shelf life of Two-part Epoxy Adhesive is one (1) year from the date of manufacture. Failing to follow the recommended storage conditions may reduce the shelf life or adhesive strength of the foam tape and Two-part Epoxy Adhesive.
Adhesive Technical Information
Adhesive foam tape properties are developed with thorough laboratory research and testing. The double-coated adhesive foam tape used on
PANDUIT
performance for use on adhesive mounts. Each package of mounts has an expiration date and a Quality Control number printed on the label, which permit traceability.
Double Coated Foam Tape Properties
Backing Material
Nominal Backing Density (pcf)
Thickness (PSTC-33)
Static Shear MIL-T-60394A (Hours)
®
Adhesive Backed Mounts is manufactured under strict quality requirements, which provide consistent, high quality
(In.) Total
Less Liner
72°F/17.6 psi
72°F/8.8 psi
158°F/2.s psi
Rubber Adhesive
Polyethylene
6
.040
.035
500+
1000+
100+
Acrylic Adhesive
Polyethylene
6
.039
.034
N/A N/A
200+
4
5
Adhesive Backed Mounts and Clips
Part Number Material
Length Width Max. Static Load
Adhesive Type
Std.
Pkg.
Qty.‡In. mm In. mm Lbs. g
4-Way Adhesive Backed Mounts
ABM1M-A-C Nylon 6.6 .50 12.7 .50 12.7 .13 59 Rubber 100
ABMM-A-C ABS .75 19.1 .75 19.1 .30 136 Rubber 100
ABM2S-A-C ABS 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM100-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM112-A-C Nylon 6.6 1.12 28.6 1.12 28.6 .63 286 Rubber 100
ABM3H-A-L Nylon 6.6 1.50 38.1 1.50 38.1
1.13 513
Rubber 50
ABM4H-A-L Nylon 6.6 2.00 50.8 2.00 50.8
1.13 513
Rubber 50
T
AK-TY
®
Hook & Loop Cable Tie Mounts
ABMT-A-C Nylon 6.6 1.10 28.7 1.10 28.6 .38 174 Rubber 100
ABMT-A-C20 Nylon 6.6
1.12 28.5 1.12 28.5
.38 174 Rubber 100
Adhesive Backed Cable Tie Mounts
Adhesive Backed Cable Clips and Clamps
Max. Static
Part Number
Material
(see notes
below table)
Length Width
Load
Adhesive Type
4-Way Adhesive Backed Cable Tie Mounts
ABM
NEW
NEW
NEW
NEW
SGA
ABM1M-A-C Nylon 6.6
ABM1M-AT-M0 WR Nylon 6.6 Acrylic
ABMM-A-C ABS
ABMM-AT-C0 WR ABS Acrylic
ABMM-AV-C ABS
ABMM-AV-C0 WR ABS
ABM2S-A-C ABS
ABM2S-AT-C0 WR ABS Acrylic
ABM100-A-C Nylon 6.6
Snap-In Cable Tie Mount
ABM100-AT-C0 WR Nylon 6.6 Acrylic
SMS-A-C ABS 2.00 50.8 1.00 25.4 1.00 454 Rubber 100
ABM100-AV-C Nylon 6.6
C
LINCHER
ARC.68-A-Q Polypropylene 1.00 25.4 1.00 25.4 .50 227 Rubber 25
ABM100-AV-C0 WR Nylon 6.6
Adhesive Backed Cord Clips
ABM112-A-C Nylon 6.6
ACC19-A-C Nylon 6.6 .63 16.0 .76 19.3 .20 91 Rubber 100
ABM112-AT-C0 WR Nylon 6.6 Acrylic
ACC38-A-C Nylon 6.6 1.00 25.4 1.00 25.4 .50 227 Rubber 100
ABM112-AV-C Nylon 6.6
ACC62-A-C Nylon 6.6 1.25 31.7 1.12 28.6 .70 318 Rubber 100
ABM112-AV-C0 WR Nylon 6.6
“J” Clips
ABM3H-A-L Nylon 6.6
AJC12-A-C PVC 1.00 25.4 .86 21.8 .40 182 Rubber 100
AJC19-A-C PVC 1.25 31.8
ABM3H-AT-L0 WR Nylon 6.6 Acrylic
AJC31-A-C PVC 1.75 44.5
ABM3H-AV-L Nylon 6.6
AJC38-A-C PVC 2.00 50.8
ABM3H-AV-L0 WR Nylon 6.6
A1C Type Clips
ABM4H-A-L Nylon 6.6
A1C12-A-C8 PVC .77 19.6 .63 16.0 .14 64 Rubber 100
ABM4H-AT-T0 WR Nylon 6.6 Acrylic
A1C25-A-C8 PVC .91 23.1 .63 16.0 .14 64 Rubber 100
A1C38-A-C8 PVC 1.04 26.4 .63 16.0 .14 64 Rubber 100
Super-Grip
A1C50-A-C8 PVC 1.17 29.7 .63 16.0 .14 64 Rubber 100
SGABM20-A-C Nylon 6.6 0.75 19.1 0.75 19.1 0.28 127 Rubber
A2C Type Clips
SGABM20-AV-C300 HS WR Nylon 6.6 0.75 19.1 0.75 19.1 0.56 254 High Bond
A2C12-A-C8 PVC 1.30 33.0 .63 16.0 .14 64 Rubber 100
A2C25-A-C8 PVC 1.43 36.3 .63 16.0 .14 64 Rubber 100
SGABM25-A-C Nylon 6.6 1.00 25.4 1.00 25.4 0.50 227 Rubber
A2C38-A-C8 PVC 1.56 39.6 .63 16.0 .14 64 Rubber 100
SGABM25-AT-C0 WR Nylon 6.6 1.00 25.4 1.00 25.4 0.50 227 Acrylic
A2C50-A-C8 PVC 1.68 42.7 .63 16.0 .14 64 Rubber 100
SGABM25-AV-C300 HS WR Nylon 6.6 1.00 25.4 1.00 25.4 1.00 454 High Bond
Metal Adhesive Backed Cord Clips
MACC25-A-C Zinc Plated Steel
SGABM30-A-C Nylon 6.6 1.12 28.4 1.12 28.4 0.63 287 Rubber
MACC62-A-C Zinc Plated Steel 1.18 30.0
Latching Wire Clips
SGABM30-AT-C0 WR Nylon 6.6 1.12 28.4 1.12 28.4 0.63 287 Acrylic
LWC19-A-C Nylon 6.6 .85 21.6 .61 15.5 .25 113 Rubber 100
SGABM30-AV-C300 HS WR Nylon 6.6 1.12 28.4 1.12 28.4 1.25 567 High Bond
LWC25-A-C Nylon 6.6 .88
LWC38-A-C Nylon 6.6
SGABM40-A-L Nylon 6.6 1.50 38.1 1.50 38.1 1.12 500 Rubber SGM, SGI, SGS,
LWC50-A-L Nylon 6.6 1.26 32.0 1.00 25.4 .63 272 Rubber 50
LWC75-A-L Nylon 6.6 1.48 37.6 1.24 31.5 .93 417 Rubber 50
SGABM50-A-L Nylon 6.6 2.00 50.8 2.00 50.8 2.00 907 Rubber SGM, SGI, SGS,
LWC100-A-L Nylon 6.6 2.21 56.1 1.97 50.0 2.25 1020 Rubber 50
Contact customer service (800-777-3300) for additional sizes, materials, and acrylic tape availability or visit www.panduit.com.
Tak-Ty
‡ Order the number of pieces required, in multiples of Standard Package Quantity.
Adjustable Releasable Clamp
Adhesive Backed Cable Tie Mounts
®
Hook & Loop Cable Tie Mounts
0.50 12.7 0.50 12.7 0.13 59
0.30 136
0.75 19.1 0.75 19.1
0.56 254
1.00 25.4 1.00 25.4 0.50 227
1.00 25.4 1.00 25.4
0.50 227
1.00 454
0.63 266
1.12 28.6 1.12 28.6
1.25 567
1.50 38.1 1.50 38.1
.87 22.1
1.22 31.0
1.27 32.3
1.13 513
2.25 1021
2.00 50.8 2.00 50.8 2.00 907
.77 19.6 .54 13.7
.78 19.8
22.4
.88 22.4
1.00 25.4 .45 204 Rubber 100
1.00 25.4 .50 227 Rubber 100
.50 227 Rubber 100
.90 408 Rubber 100
1.00 454 Rubber 100
.21 95 Rubber 100
.44 200 Rubber 100
Rubber
Rubber
High Bond
Acrylic
Rubber
Rubber
High Bond
Acrylic
Rubber
High Bond
Acrylic
Rubber
High Bond
Acrylic
Rubber
Acrylic
Acrylic
Acrylic
ABMT-A-C Nylon 6.6 1.12 28.5 1.12 28.5 0.38 174 Rubber HLT, HLS, TTS, UCT
Snap-In Cable Te Mount
ABMT
SMS
SMS-A-C ABS 2.00 50.8 1.00 25.4 1.00 454 Rubber S
Material Notes: WR = Weather Resistant, HS = Heat Stabilized ^ Visit www.panduit.com for additional packaging and material/color availability. ^^ Cable Tie Cross Section Designation: M = miniature, I = intermediate, S = standard, LH = light heavy, H = heavy SG = Super-Grip, HLT = Tak-Ty
Hook & Loop Ties, HLS = Tak-Ty™ Hook & Loop Ties, TTS = Tak-Tape™ Roll, UCT = Ultra-Cinch™ Tie
Used with Cable
Ties ^^In. mm In. mm Lbs. g
M
M, I
M, I, S
M, I, S
M, I, S
M, I, S, LH, H
M, I, S, LH, H
SGM, SGI
SGM, SGI, SGS
SGM, SGI, SGS
SGLH, SGH
SGLH, SGH
ARC
ACC
AJC
A1C
A2C
MACC
LWC
Max. Static
Part Number^
Clincher
Adjustable Releasable Clamp
Material
(see notes
below table)
Length Width
Load
Adhesive Type
Max. Cable
Dia. In. (mm)In. mm In. mm Lbs. g
ARC.68-A-Q Polypropylene 1.00 25.4 1.00 25.4 0.50 227 Rubber 0.68 (17.3)
Adhesive Backed Cord Clips
ACC19-A-C Nylon 6.6 0.63 16.0 0.76 19.3 0.24 109 Rubber 0.19 (4.8)
ACC19-AT-C0 WR Nylon 6.6 0.63 16.0 0.76 19.3 0.24 109 Acrylic 0.19 (4.8)
ACC19-AV-M300 HS WR Nylon 6.6 0.63 16.0 0.76 19.3 0.48 218 High Bond
Acrylic
0.19 (4.8)
ACC38-A-C Nylon 6.6 1.00 25.4 1.00 25.4 0.50 227 Rubber 0.38 (9.6)
ACC38-AT-C0 WR Nylon 6.6 1.00 25.4 1.00 25.4 0.50 227 Acrylic 0.38 (9.6)
ACC38-AV-M300 HS WR Nylon 6.6 1.00 25.4 1.00 25.4 1.00 454 High Bond
Acrylic
0.38 (9.6)
ACC62-A-C Nylon 6.6 1.24 31.4 1.12 28.5 0.69 315 Rubber 0.62 (15.7)
ACC62-AT-C0 WR Nylon 6.6 1.24 31.4 1.12 28.5 0.69 315 Acrylic 0.62 (15.7)
ACC62-AV-D300 HS WR Nylon 6.6 1.24 31.4 1.12 28.5 1.39 631 High Bond
Acrylic
0.62 (15.7)
“J” Clips
AJC12-A-C PVC 1.00 25.4 0.86 21.8 0.40 181 Rubber 0.12 (3.0)
AJC19-A PVC 1.25 31.8 0.87 22.1 0.50 227 Rubber 0.19 (4.8)
AJC25-A PVC 1.50 38.1 0.97 24.6 0.58 263 Rubber 0.25 (6.4)
AJC31-A PVC 1.75 44.5 1.22 31 0.90 408 Rubber 0.31 (7.9)
AJC38-A PVC 2.00 50.8 1.27 32.3 1.00 454 Rubber 0.38 (9.6)
A1C Type Clips
A1C12-A-C8 PVC 0.77 19.6 0.63 16.0 0.14 64 Rubber 0.12 (3.0)
A1C25-A-C8 PVC 0.91 23.1 0.63 16.0 0.14 64 Rubber 0.25 (6.4)
A1C38-A-C8 PVC 1.04 26.4 0.63 16.0 0.14 64 Rubber 0.38 (9.6)
A1C50-A-C8 PVC 1.17 29.7 0.63 16.0 0.14 64 Rubber 0.50 (12.7)
A2C Type Clips
A2C12-A-C8 PVC 1.30 33.0 0.63 16.0 0.28 128 Rubber 0.12 (3.0)
A1C25-A-C8 PVC 1.43 36.3 0.63 16.0 0.28 128 Rubber 0.25 (6.4)
A1C38-A-C8 PVC 1.56 39.6 0.63 16.0 0.28 128 Rubber 0.38 (9.6)
A1C50-A-C8 PVC 1.72 43.7 0.63 16.0 0.28 128 Rubber 0.50 (12.7)
Metal Adhesive Backed Cord Clips
MACC25-A-C Zinc-Plated Steel 0.77 19.6 0.54 13.7 0.21 95 Rubber 0.25 (6.4)
MACC25-AV-D Zinc-Plated Steel 0.77 19.6 0.54 13.7 0.42 191 High Bond
0.25 (6.4)
Acrylic
MACC62-A-C Zinc-Plated Steel 1.18 30.0 0.78 19.8 0.46 209 Rubber 0.62 (15.7)
MACC62-AV-C Zinc-Plated Steel 1.43 36.3 0.63 16.0 0.92 418 High Bond
0.62 (15.7)
Acrylic
Latching Wire Clips
LWC19-A-C Nylon 6.6 0.85 21.6 0.61 15.5 0.25 113 Rubber 0.19 (4.8)
LWC25-A-C Nylon 6.6 0.88 22.4 1.00 25.4 0.45 204 Rubber 0.25 (6.4)
LWC38-A-C Nylon 6.6 1.00 25.4 1.00 25.4 0.50 227 Rubber 0.38 (9.6)
LWC50-A-L Nylon 6.6 1.26 32 1.00 25.4 0.63 272 Rubber 0.50 (12.7)
LWC75-A-L Nylon 6.6 1.48 37.6 1.24 31.5 0.92 417 Rubber 0.75 (19.1)
LWC100-A-L Nylon 6.6 2.21 56.1 1.97 50.0 2.18 988 Rubber 1.0 (25.4)
Material Notes: WR = Weather Resistant, HS = Heat Stabilized ^ Visit www.panduit.com for additional packaging and material/color availability.
Continued on next page
6
7
Adhesive Backed Cable Clips and Clamps (continued)
Epoxy Applied Mounts
BEC
VCC
LC
CH
LPFCM
FCM
FCC
Max. Static
Part Number^
Material
(see notes
below table)
Length Width
Load
Adhesive Type
Max. Cable
Dia. In. (mm)In. mm In. mm Lbs. g
Bevel Entry Clips
BEC38-A-L Nylon 6.6 1.46 37.1 1.24 31.5 0.91 411 Rubber 0.38 (9.6)
BEC62-A-T Nylon 6.6 1.46 37.1 1.24 31.5 0.91 411 Rubber 0.62 (15.7)
BEC75-A-L Nylon 6.6 1.46 37.1 1.49 37.8 1.09 494 Rubber 0.75 (19.1)
Vertical Cord Clip
VCC25-A-C Nylon 6.6 1.00 25.4 0.50 12.7 0.25 113 Rubber 0.25 (6.4)
Adhesive Backed Latching Clips
LC3-A-C8 PVC 0.75 19.0 0.78 19.8 0.24 110 Rubber 0.25 (6.4)
LC5-A-C8 PVC 1.00 25.4 1.01 25.7 0.44 200 Rubber 0.36 (9.1)
LC10-A-L8 PVC 1.00 25.4 1.51 38.4 0.60 272 Rubber 0.93 (23.6)
Cable Holder
CH105-A-C14 Nylon 6.6 2.48 63.0 1.03 26.2 1.28 581 Rubber 5 X .39 (10)
Material Notes: WR = Weather Resistant, HS = Heat Stabilized ^ Visit www.panduit.com for additional packaging and material/color availability.
Flat Cable Mounts
Max. Static
Load
Adhesive Type
Flat Cable
Width In. (mm)In. mm In. mm Lbs. g
Part Number^
Material
(see notes
below table)
Length Width
Low Prole Flat Cable Mounts
LPFCM14-A-C14 Nylon 6.6 2.56 65.0 0.50 12.7 0.25 113 Rubber 1.44 (36.6)
LPFCM22-A-C14 Nylon 6.6 3.31 84.1 0.50 12.7 0.25 113 Rubber 2.19 (55.6)
LPFCM34-A-C14 Nylon 6.6 4.56 115.8 0.50 12.7 0.25 113 Rubber 3.44 (87.4)
Latching Flat Cable Mounts
FCM1-A-C14 Nylon 6.6 1.21 30.7 1.00 25.4 0.50 227 Rubber 1.05 (26.7)
FCM1.2-A-C14 Nylon 6.6 1.37 34.8 1.00 25.4 0.68 311 Rubber 1.20 (30.5)
FCM2-A-C14 Nylon 6.6 2.22 56.4 1.00 25.4 1.00 454 Rubber 2.05 (52.1)
FCM3.25-A-L14 Nylon 6.6 3.38 85.9 1.00 25.4 1.50 680 Rubber 3.23 (62.0)
Latching Flat Cable Holder
FCH2-A-T14 Nylon 6.6 2.48 63.0 1.03 26.2 1.28 581 Rubber 2.06 (52.2)
Flat Cable Clips
FCC-A-C8 Nylon 6.6 1.00 25.4 1.09 27.7 0.50 227 Rubber
FCC5-A-C8 Nylon 6.6 1.00 25.4 0.56 14.2 0.25 117 Rubber
Material Notes: WR = Weather Resistant, HS = Heat Stabilized ^ Visit www.panduit.com for additional packaging and material/color availability.
ASMS
EMS
EMS KITS
Material
Part Number^
(see notes
below table)
ASMS-A-X Aluminum Base,
Max. Static
Length Width
Load
In. mm In. mm Lbs. g
1.13 28.5 1.13 28.5 10.00 4540 EMA Epoxy M, I, S
Adhesive Type
(not included,
purchase EMA-X)
Campatible Ties
(Cross-Section)
Nylon 6.6 Mount
EMS-A-C Nylon 6.6 0.98 24.9 0.98 24.9 10.00 4540 EMA Epoxy M, I, S
EMS-A-C0 WR Nylon 6.6 0.98 24.9 0.98 24.9 10.00 4540 EMA Epoxy M, I, S
Material Notes: WR = Weather Resistant, HS = Heat Stabilized ^ Visit www.panduit.com for additional packaging and material/color availability.
Epoxy Applied Mount Kits
Used with
Part Number^ Color Environment
Cable Ties
Epoxy Adhesive Only
EMA-X Gray Indoor/
10 10 10
Outdoor
Epoxy Mounting Kit with EMS Mounts
EMSK3-1-X0 Black Indoor/
M, I, S 3 1 1 10
Outdoor
Epoxy Mounting Kit with EMS Mounts and Cable Ties
EMSK3-1-3-0 Black Indoor/
M, I, S (3) PLT2S-0 3 1 1 1
Outdoor
EMSK12-4-12-X0 Black Indoor/
M, I, S (3) PLT2S-0 12 4 4 10
Outdoor
^ Visit www.panduit.com for additional packaging and material/color availability. ‡Order the number of pieces required, in multiples of Standard Package Quantity.
Number of Cable Ties
Number of
EMS Mounts
Number of
Epoxy Cups
Number of
Mixer Sticks
Std. Pkg.
Qty.
8
9
PANDUIT CANADA Markham, Ontario cs-cdn@panduit.com Phone: 800.777.3300
PANDUIT EUROPE LTD. London, UK cs-emea@panduit.com Phone: 44.20.8601.7200
For a copy of Panduit product warranties, log on to www.panduit.com/warranty
WORLDWIDE SUBSIDIARIES AND SALES OFFICES
PANDUIT SINGAPORE PTE. LTD. Republic of Singapore cs-ap@panduit.com Phone: 65.6305.7575
PANDUIT JAPAN Tokyo, Japan cs-japan@panduit.com Phone: 81.3.6863.6000
For more information
Visit us at www.panduit.com
Contact Customer Service by email: cs@panduit.com
or by phone: 800.777.3300
PANDUIT LATIN AMERICA Guadalajara, Mexico cs-la@panduit.com Phone: 52.33.3777.6000
PANDUIT AUSTRALIA PTY. LTD. Victoria, Australia cs-aus@panduit.com Phone: 61.3.9794.9020
©2021 Panduit Corp.
ALL RIGHTS RESERVED.
SA-WACB06
04/2021
Loading...