Panasonic of North America SYNCG3 L User Manual
Ford Motor Company
Re: Certification for Ford SYN C FCC ID: ACJ SYNCG3 L
IC: 216B SY NCG3L
Product Development 20300 Rotun da Drive D earborn, MI 48124
N ovember 26 , 2014
INFORMATION TO BE IN CLUDED IN THE END USER'S MANU AL
The foll wing inform ation must be included in the end p roduct user’s manual to ensure continued FCC and Ind ustry Canada regulatory compliance. The ID numbers must be included i n the manual if the device l abel is not re adily accessible to the end user. Th complianc e paragraph (in blue) be low must be inclu ded in the u ser's manual.
This device contains a transmitt er and anten na that mus t be installed to ensure a 20 cm separation distance is maintained between all passeng rs and the transmitter a nd its anten na.
************************************************************************
The end user’s manu al is currently under preparation. Fo rd Motor Company will include the f ollowing material in the end u ser’s manual for the com mercial product:
F CC ID: ACJ SY NCG3 L IC: 216B SYNCG3L
Federal Communications Commission (FCC) Statement
You are cautioned that changes or m odifications not expressly approved by t he part respo nsible for co mpliance could void the user’s authority to op erate the equ ipment.
This equipment has been tested and found to com ply with the limits for a Cl ass B digital d evice, pursua nt to part 15 of the FCC rules. These limits are designed to p rovide reason able protection against harmful interference in a residenti al installation. This equipm ent generates, uses and can radiate radio frequency e nergy and, if n ot installed and used in accordanc e with the instructions, ma y cause harmful interference to radio co mmunications. However, there is no guarantee that interfere nce will not oc cur in a parti cular installation. If this equ ipment does cause harmful interference t o radio or tele vision recept on, which ca be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving ntenna.
Increase the separati on between t he equipment and receiver.
Connec t the equipme nt into an ou tlet on a circuit different fr om that to which the receiver is connect ed.Consult the dealer or an experienc ed radio/TV t echnician for help.
This device complies with Part 15 of the FCC R ules. Operation is subject to the following two conditions:
1)this device may not cause harmful interference, and
2)this device must accept any interference received, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) Statement
This device complies with Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Loading...