Page 1
(Lens : option)
Before attempting to connect or operate this product,
please read these instructions completely.
CCTV Cameras
WV-BP330/WV-BP332/WV-BP334
ENGLISHDEUTSCH
FRANÇAISESPAÑOL
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK), NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
ENGLISH VERSION
Wij verklaren als enige aansprakelijke, dat het product waarop
deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de
bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med den
følgende standarder eller andre normative dokumenter i følge
bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som
framstölls i Direktiv 73/23/EEC och 89/336/EEC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita
ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC
ia 89/336/EEC. säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som fælger
bestemmelsene i direktiven 73/23/EEC og 89/336/EEC.
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the standards or other normative documents following the provisions of
Directives EEC/73/23 and EEC/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi
alle disposizioni delle direttive CEE/73/23 e CEE/89/336.
Page 3
ENGLISH
-1-
The serial number of this product may be found on the top
of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of
your purchase to aid identification in the event of theft.
Model No.
Serial No.
For U.K.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement
fuse has a rating of 5 amp and that it is approved by ASTA or BSI to
BS1362.
Check for the ASTA mark
H or the BSI mark G on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement
cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic
Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET
OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED
AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT
OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following
code.
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to
the terminal in the plug which is marked with the letter E or by the earth
symbol
I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in
the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
in the plug which is marked with the letter L or coloured red.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
Page 4
CONTENTS
PREFACE ........................................................................................................................................................................ 3
FEATURES ...................................................................................................................................................................... 3
PRECAUTIONS ............................................................................................................................................................... 4
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ......................................................................................... 5
CONNECTIONS .............................................................................................................................................................. 9
FOCUS OR BACK-FOCAL ADJUSTMENT .................................................................................................................... 14
INSTALLATION OF CAMERA ........................................................................................................................................ 15
PREVENTION OF BLOOMING AND SMEAR ................................................................................................................ 16
SPECIFICATIONS .......................................................................................................................................................... 17
STANDARD ACCESSORIES ......................................................................................................................................... 18
-2-
Page 5
-3-
1. The following functions are built-in.
(1) Auto Light Control (ALC)/Electronic Light
Control (ELC)
(2) Back Light Compensation (ON: Photometric
weight is given to the centre of the
screen/OFF: Effective if the object is not in the
centre of the screen)
(3) Various External Sync Functions, including
Gen-Lock
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.08 lx (0.008 foot-candle)
with F1.4 lenses
4. Horizontal resolution of 570 lines
5. Shooting of indoor scenes with fixed iris lens by
use of Electronic Light Control (ELC) function
ture elements), and digital signal processing LSI’s. This
model offers cutting-edge technology for advanced
video surveillance.
PREF ACE
Panasonic’s WV-BP330 series digital cameras introduce a new level of high picture quality and high resolution through the use of a 1/3-inch interline transfer
CCD image sensor having 752 horizontal pixels (pic-
FEATURES
6. Selectable auto iris control signal for the lens from
a video signal or DC control signal
Page 6
-4-
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws
or covers.
There are no user serviceable parts inside. Ask a
qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking,
etc. The camera could be damaged by improper
handling or storage.
3. Do not expose the camera to rain or moisture,
or try to operate it in wet areas.
Turn the power off immediately and ask a qualified
service person for servicing. Moisture can damage
the camera and also create the danger of electric
shock.
4. Do not use strong or abrasive detergents when
cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether
the camera is in use or not, never aim it at the sun
or other extremely bright objects. Otherwise,
blooming or smear may be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where temperature is between –10°C - +50°C (14°F - 122°F), and
humidity is below 90%. The input power source is
220-240V AC 50Hz for WV-BP330, 12V DC for WVBP332, and 24V AC 50Hz for WV-BP334.
PRECAUTIONS
Page 7
-5-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
WV-
BP330
VIDEO OUT
GEN-LOCK
L
INT
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVEL
V. PHASE
H
Ω
LL
OFF
ELC
OFF
DC
Hi-Z
GND
AC 24V IN
12
VIDEO OUT
GEN-LOCK
L
INT
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVEL
V. PHASE
H
Ω
LL
OFF
ELC
OFF
DC
Hi-Z
DC 12V IN
VIDEO OUT
GEN-LOCK
L
AGC ON
ALC
BLC ON
VIDEO
G/L 75
VIDEO
LEVEL
H
Ω
OFF
ELC
OFF
DC
Hi-Z
<WV-BP330>
<WV-BP332>
<WV-BP334>
Page 8
-6-
q Auto Iris lens Connector
This connector is for connecting auto iris lens by a
4-pin male connector supplied as a standard
accessory (Part No. YFE4191J100).
w Back-focal Adjusting Ring
This ring is adjusts the back-focal length or picture
focus. Rotate this ring clockwise for a C-mount
lens or counterclockwise for a CS-mount lens.
e Lens (option)
r Camera Mounting Screw Hole
This hole is for mounting the camera onto a mounting bracket.
t Power Cord (only WV-BP330)
Connect this power cord to an electrical outlet of
220-240V AC 50Hz.
y DC 12 V Input Terminal
(DC 12V IN (only WV-BP332))
This terminal is for connecting the 12V DC power
supply cord.
u AC 24V Input Terminal
(AC 24V IN (only WV-BP334))
This terminal is for connecting the 24V AC 50Hz
power supply cord.
i Synchronization Mode Selector
(INT, LL (only WV-BP330 and WV-BP334))
Selects the camera synchronization mode from
internal sync mode (INT) or line-lock mode (LL).
INT: When no signal is supplied to the GEN-LOCK
connector, the camera synchronization mode
is set to internal 2:1 interlace. Whenever the
gen-lock video signal is supplied to the GENLOCK connector, the camera synchronization
mode is automatically set to external synchronization.
LL: The camera synchronization mode is set to
line-lock even if the gen-lock video signal is
supplied to the GEN-LOCK connector.
Note: Set this selector to INT for gen-lock opera-
tion.
o AGC ON/OFF Selector (AGC ON, OFF)
Selects the gain of the video amplifier as follows:
AGC ON: When the lens iris is fully open under
low light condition, a clear picture is obtained
by automatic increase of the gain.
OFF: A natural and low-noise picture is obtained
under low light conditions.
Page 9
-7-
!0 Automatic Light Control / Electronic Light
Control Selector (ALC , ELC)
Lets you select the mode according to the lens
type that is used with this camera.
ALC: Select this mode when an auto iris lens (ALC
lens) is used with this camera.
ELC: Select this mode when a fixed iris lens or
manual iris lens is used with this camera.
!1 Back Light Compensation Mode Selector (BLC
ON, OFF)
Lets you select the mode according to the position
of the object and light conditions on the screen.
BLC ON: More photometric weight is given to the
centre of the screen than to the edge of the
screen. Select this mode if the background
light is strong such as a spotlight.
OFF: Lets you this mode if the main object is not
located in the centre of the screen and a
source of bright light is located near the cen-
tre of the screen.
!2 Lens Drive Signal Selector (VIDEO, DC)
Lets you select the mode according to the type of
auto iris lens drive signal to be supplied to the lens
from the auto iris lens connector.
VIDEO: Select this mode if you are using the auto
iris lens that requires a video drive signal.
DC: Select this mode if you are using the auto iris
lens that requires a DC drive signal.
!3 Gen-lock Termination Selector (Hi-Z, G/L75Ω)
Set this selector to Hi-Z when a gen-lock video
input signal is looped through. In all other cases,
set this selector to 75Ω.
!4 Vertical Phase Control
(V. PHASE (only WV-BP330 and WV-BP334))
Allows you to adjust the vertical phase of the camera signal to match the vertical phase of the line
power.
!5 Video Level Control (VIDEO LEVEL, H(High)-
L(Low))
Allows you to adjust the video level when the Lens
Drive Signal Selector is set to DC and the auto iris
lens requiring the DC drive signal is mounted on
the camera.
Note: The video level should be adjusted by the
lens when the auto iris lens requiring the video
drive signal is mounted on the camera.
!6 Video Output Connector (VIDEO OUT)
This connector is for connecting with the VIDEO IN
connector of the monitor.
Page 10
-8-
Caution:
Connect to 12V DC (10.5V-16V) or 24V AC
(19.5V-28V) class 2 power supply only.
Make sure to connect the grounding lead
to the GND terminal when the power is
supplied from a 24V AC power source.
!7 Gen-lock Input Connector (GEN-LOCK)
This connector is for connecting an external system for synchronization.
Page 11
-9-
CONNECTIONS
A. WV-BP330 (220-240V AC 50Hz)
Connect the power cord to an electrical outlet of
220-240V AC 50Hz.
B. WV-BP332 (12V DC)
Connect the power cord to the DC 12V IN terminal
on the rear panel of the WV-BP332.
12 V DC
(10.5 V - 16 V)
Copper wire #24 #22 #20 #18
size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
Resistance 0.078 0.050 0.030 0.018
Ω/m
Resistance 0.026 0.017 0.010 0.006
Ω/ft
Resistance of copper wire [at 20°C (68°F)]
• Calculation of maximum cable length between
camera and power supply :
10.5V DC ≤ V
A − (R x 0.42 x L) ≤ 16V DC
L : Cable length (meters)
R : Resistance of copper wire (Ω/meters)
V
A : DC output voltage of power supply unit
V
A − 12
L standard = (meters)
0.42 x R
V
A − 16
L minimum = (meters)
0.42 x R
V
A − 10.5
L maximum = (meters)
0.42 x R
@
!
Page 12
-10-
C. The maximum extensible coaxial cable
length between the camera and the monitor is
shown below.
Video Cable
1. It is recommended to use a monitor whose resolution is at least equal to that of the camera.
2. Set the termination switch to the 75Ω position on
the last monitor.
A. Use a 75Ω coaxial cable.
B. Set the termination switch to the 75Ω posi-
tion on the last monitor and to the Hi-Z position on the other monitors. Do not change the
positions after setting.
OUTIN 75
¶
Hi-Z
VIDEO
OUTIN 75
¶
Hi-Z
VIDEO
Monitor
Monitor
24 V AC, 50 Hz
(19.5 V - 28 V)
1
2
C. WV-BP334 (24V AC 50Hz)
Connect the power cable to the AC 24V IN terminal on the rear panel of the WV-BP334.
Copper wire #24 #22 #20 #18
size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
Length (m) 95 150 255 425
of Cable
(Approx.) (ft) 314 495 842 1 403
Recommended wire gauge sizes for 24V AC line
Page 13
3. Wiring precautions:
• Do not bend the coaxial cable into a curve whose
radius is smaller than 10 times the cable’s diameter.
• Never staple the cable, not even with circular staples. Impedance mismatching will occur.
• Never crush or pinch the cable.
All of the above will change the impedance of the
cable and cause poor picture quality.
-11-
Type of RG-59/U RG-6/U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800
maximum
cable length (ft) 825 1 650 1 980 2 640
Page 14
-12-
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a
video drive ALC lens.
The installation should be made by qualified service personnel or system installers.
(1) Cut the iris control cable at the edge of the lens
connector to remove the existing lens connector
and then remove the outer cable cover as shown
in the diagram below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9V DC, 50mA max.
Pin 2: Not used
Pin 3: Video signal; 1.3 V[p-p]/40 kΩ
Pin 4: Shield, ground
Pin 3
Pin 4
Pin 2
Rib
Pin 1
Note: When the iris control cable is too thick to
lock the connector cover with the connector
base, cut off the rib on the connector.
(Set the Lens Drive Signal Selector to the
VIDEO position.)
(2) After connection, assemble the lens connector as
follows.
Automatic
Iris Lens
Iris Control
Cable
Connector
Heat
Shrinkable
Tubes
Connector
Cover
Page 15
-13-
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount (1”32UN) and the lens weight should be less than 450g
(0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter.
The protrusion at the rear of the lens should be as
shown below:
C-mount: Less than 11.5 mm (7/16”)
CS-mount: Less than 7.2 mm (1/4”)
1
2
Screws
Back-focal
Adjusting Ring
Mounting the Lens
Caution:
Before you mount the lens, loosen the two screws
on the ring, and rotate this ring clockwise until it
stops. If the ring is not at the end, the inner glass
or CCD image sensor may be damaged.
1. Mount the lens by turning it clockwise on the lens
mount of the camera.
2. Connect the lens cable to the auto iris lens connector on the side of the camera.
Page 16
-14-
The following adjustment should be made by qualified
service personnel or system installers.
1. Loosen the screws on the back-focal adjusting
ring.
2. Turn the back-focal adjusting ring to the desired
position.
Caution: When the C-mount lens is mounted, do
not rotate the ring counterclockwise by force
after it stops. If the ring is rotated by force, the
inner lens or CCD image sensor may be damaged.
3. Tighten the screws on the back-focal adjusting
ring.
Note: If the camera is connected to the Quad
System, glare may appear at the edge of the
camera picture on the monitor.
If this bothers you, adjust the lens focus to
reduce the glare.
Focus adjustment for
C-mount lens
Focus adjustment for
CS-mount lens
Screws
Back-focal
Adjusting Ring
FOCUS OR BACK-FOCAL ADJUSTMENT
Page 17
-15-
• Mounting from the bottom
This camera is designed to be mounted from the
bottom, as shown below. The mounting hole is a
standard photographic pan-head screw size (1/4”
- 20).
• Mounting from the top
Remove the mount adapter from the bottom of the
camera by removing the two fixing screws. Attach
the mount adapter to the top as shown in the diagram, then mount the camera on the mounting
bracket.
Make sure that the two original fixing screws are
used when mounting the mount adapter as longer
length screws may damage inner components.
Fixing Screws
Mount Adapter
<Mounting at top>
<Mounting at bottom>
INSTALLATION OF CAMERA
Page 18
-16-
When the camera is aimed at a bright light, such as a
spot light, or a surface that reflects bright light, smear
or blooming may appear. Therefore, the camera
should be operated carefully in the vicinity of extremely
bright objects to avoid smear or blooming.
Bright object
Smear
PREVENTION OF BLOOMING AND SMEAR
Page 19
Pick-up Device: 752 (H) x 582 (V) pixels, Interline Transfer CCD
Scanning Area: 4.9 (H) x 3.7 (V) mm (Equivalent to scanning area of 1/3” pick-up tube)
Synchronization: Internal, External, Line-locked or Multiplexed vertical drive (VD2) selectable
Scanning System: 2 : 1 interlace
Scanning: 625 lines / 50 fields / 25 frames
Horizontal: 15.625 kHz
Vertical: 50.00 Hz
Horizontal Resolution: 570 lines
Video Output: 1.0 V[p-p] CCIR composite 75 Ω / BNC connector
Signal-to-Noise Ratio: 50 dB (AGC OFF)
Electronic Light Control: Equivalent to continuous variable shutter speed between 1/50 s
and 1/10 000 s
Minimum Illumination: 0.08 lx (0.008 footcandle) at F1.4, AGC ON
Gain Control: AGC ON (+18 dB) or OFF selectable
Lens Mount: C-mount or CS-mount selectable
Ambient Operating Temperature: −10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity: Less than 90%
Power Source and WV-BP330: 220-240V AC 50 Hz, 4.5W
Power Consumption: WV-BP332: 12V DC, 250 mA
WV-BP334: 24V AC 50 Hz, 3.5W
-17-
SPECIFICATIONS
Page 20
Dimensions (without lens): 67 (W) x 55 (H) x 123 (D) mm
[2-5/8” (W) x 2-3/16” (H) x 4-13/16” (D)]
Weights (without lens): WV-BP330: 0.635kg (1.40lbs)
WV-BP332: 0.445kg (0.98lbs)
WV-BP334: 0.470kg (1.04lbs)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
-18-
STANDARD ACCESSORIES
Body Cap .....................................................................................1 pc.
ALC Lens Connector (YFE4191J100) ..........................................1 pc.
Page 21
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
N0398-1048 YWV8QA4917BN Printed in Japan
N 30 Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Loading...