Panasonic TX-32LX70F, TX-32LX70L, TX-32LX70P, TX-26LX70F, TX-26LX70L Service manual

ORDER No. PCZ0702011CE

ISSUE 2

Service Manual

Colour LCD Television

TX-32LX70F TX-32LX70L

TX-32LX70P

TX-26LX70F TX-26LX70L

TX-26LX70P

LH64 Chassis

Specifications

(Informations in brackets [ ] refers to model 26”)

Power Source: 220-240V AC, 50/60Hz

Power Consumption 134W [100W]

Stand-by Power Consumption: 0.4W Aerial Impedance: 75Ω unbalanced, Coaxial Type

Receiving System: LX70L LX70F, LX70P PAL-I, PAL-I/H, B/G, D/K,

PAL-525/60 (AV only) SECAM B/G, D/K, L/L’ M.NTSC (AV only) PAL-525/60 (A V only) NTSC (AV only) M.NTSC (AV only) NTSC (AV only)

Receiving Channels: LX70L LX70F, LX70P UHF E21-E68 VHF E2-E12 VHF H1-H2 (ITALY)

VHF A-H (ITALY) VHF R1-R2 VHF R3-R5 VHF R6-R12 UHF E21-E69 CATV (S01-S05) CATV S1-S10 (M1-M10) CATV S11-S20 (U1-U10) CATV S21-S41 (Hyperband)

Operating Conditions: Temperature: 0°C ÷ 35°C Humidity: 20% ÷ 80% RH (non condensing)

Scanning format: 480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(60Hz), 720p(50Hz), 1.080i(60Hz),

1.080i(50Hz), 1.080p(60Hz), 1.080p(50Hz) PC signals: VGA, SVGA, XGA, SXGA(compressed)

Horizontal scanning frequency 31 – 69 kHz Vertical scanning frequency 59 – 86 Hz

Intermediate Frequency:

Video/Audio LX70L LX70F, LX70P

Video 38,9MHz 38,9MHz, 33,9MHz

Audio 32.90MHz 33,4MHz (B/G), 33,16MHz (A2)

32.35MHz(NICAM) 33,05MHz (NICAM B/G, D/K, L)

32,4MHz (D/K), 32,66MHz (CZ STEREO) 40,4MHz (L

Colour 34,47MHz 34,47MHz (PAL)

’), 39,75MHz (L’NICAM)

34,5MHz, 34,65MHz (SECAM) 38,3MHz, 38,15MHz (SECAM L

Terminals:

’)

AV1 IN Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 10kΩ RGB (21 pin) 0,7V p-p 75Ω

AV1 OUT Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 1kΩ

AV2 IN Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 10kΩ RGB (21 pin) 0,7V p-p 75Ω S-video IN (21-pin) Y: 1V p-p 75Ω C:0,3V p-p 75Ω

AV2 OUT Video (21 pin) 1V p-p 75Ω Audio (21 pin) 500mV rms 1kΩ

AV3 IN S-Video IN (4-pin) Y: 1V p-p 75Ω C:0,3V p-p 75Ω

Audio (RCAx2) 500mV rms 10kΩ

Video (RCAx1) 1V p-p 75Ω HDMI1, HDMI2 Type A Connector COMPONENT Video (RCAx3) Y:1V p-p 75Ω (including synchronization)

Pb, Pr: ±0,35V p-p 75Ω AUDIO IN Audio (RCAx2) 500mV rms 10kΩ (for YUV, HDMI1)

AUDIO OUT Audio (RCAx2) 500mV rms 1kΩ (high impedance) PC HIGH-DENSITY D_SUB 15PIN R,G,B: 700mV p-p 75Ω

HD,VD/TTL Level 2-5V p-p (high impedance)

LCD screen: L5EDD8Q00030 [L5EDD6Q00024] 1366 x 768 XGA, 16:9 Visible Diagonal 800mm [660mm]

Audio Output: 20W (2x10W) Headphones: 3,5mm, 8Ω Impedance Accessories supplied : Remote Control 2 x R6 (UM3) Batteries Dimensions:

Height: Width: Depth: Including TV stand 615mm 791mm 248mm [525mm] [657mm] [216mm]

TV set only 563mm 791mm 117mm [473mm] [657mm] [117mm]

Net weight: 17,5kg [14kg] Specifications are subject to change without notice.

Weights and dimensions shown are approximate.

Warning

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products deal within this service information by anyone else could result in serious injury or death.

2

Safety Precautions

Ω

General Guide Lines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such a s insulation barriers, insulation papers shields are properly installed.

3. After servicing, make the following touch current checks to prevent the customer from being exposed to shock hazards.

4. Always ensure panel TKP0E16001 is correctly replaced before returning to customer (see Fig.1).

Touch-Current Check

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transfor mer for this check.

2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Fig. 2.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reserve the AC plug in the AC outlet and repeat each of the above measure.

6. The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values: For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak); For d. c.: U1 = 1.0 V,

Note:

The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and

2.0 mA d. c. The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.

7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

COLD WATER PIPE (EARTH GROUND)

TO APPLIANCES EXPOSED

METAL PARTS Resistance values in ohms (Ω) V: Voltmetr or oscilloscope

(r.m.s. or peak reading)

NOTE – Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms

Measuring network for TOUCH CURRENTS

Input resistance: ≥ 1MΩ Input capacitance: ≤ 200pF Frequency range: 15Hz to 1MHz and d.c.respectively

R

=1500Ω

S

Fig. 1

R0=500Ω

Fig. 2

C

=0.22µF

S

U

10k

1

0.022µF

V

U2 (V)

4

Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build up or exposure of the assembly.

3. Use only a grounded-tip s oldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelle d chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by cond uctive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protectiv e material from the le ads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

There are special components used in this equipment which are important for safety. These parts are marked by in schematic diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

5

About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d suggest the use of Pb free solder as well, although Pb solder may be used. PCBs manufactured using lead free solder will have the PbF within a leaf Symbol

stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40°C)

higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too hi gh (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may

flow onto the opposite side. (see Fig.3)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used. (see Fig.4)

Fig.3

Fig.4

6

Applicable signals

Component (Y, Pb, Pr), HDMI

Signal name COMPONENT HDMI

525 (480) / 60i * * 525 (480) / 60p * *

625 (576) / 50i * * 625 (576) / 50p * * 750 (720) / 60p * * 750 (720) / 50p * * 1,125 (1,080) / 60i * * 1,125 (1,080) / 50i * * 1,125 (1,080) / 60p * 1,125 (1,080) / 50p *

PC (D-sub 15P)

Signal name Horizontal frequency (kHz) Vertical frequency (Hz)

640 × 400 @70 Hz 640 × 480 @60 Hz 640 × 480 @75 Hz 800 × 600 @60 Hz 800 × 600 @75 Hz 800 × 600 @85 Hz 852 × 480 @60Hz 1,024 × 768 @60Hz 1,024 × 768 @70Hz 1,024 × 768 @75Hz 1,024 × 768 @85Hz 1,280 × 1,024 @60Hz 1,366 × 768 @60Hz Macintosh 13“ (640 × 480) Macintosh 16“ (832 × 624) Macintosh 21“ (1,152 × 870)

Note:

• Signals other than above may not be displayed properly.

• The above signals are reform atted for optimal viewing on your display.

• Applicable input signal for PC is basicall y com patible to VESA standard timing.

• PC signal is magnified or compresse d for display, so that it may not be possible to show fine detail

with sufficient clarity.

31.47 70.07

31.47 59.94

37.50 75.00

37.88 60.32

46.88 75.00

53.67 85.06

31.44 59.89

48.36 60.00

56.48 70.07

60.02 75.03

68.68 85.00

63.98 60.02

48.39 60.04

35.00 66.67

49.73 74.55

68.68 75.06

7

Service Hints

How to remove the backcover

Remove the 18 [16] fixing screws. (see Fig.5)

SCREWS

How to remove the Pedestal assembly

Lay the main unit face down. (see Fig.6)

Remove the 4 fixing screws and the pedestal assembly. (see Fig.7)

Fig.5

Fig.6

Fig.7

SCREWS

8

Chassis Board Layout

AP-BOARD

DG-BOARD

H-BOARD

G-BOARD

Board Name Function

AP-Board Power Supply Regulator

DG-Board Global Core, HDMI, IDTV Processor, D/A Converter

G-Board Side AV Connector H-Board AV Connector, TV tuner, AV Switch K-Board Main Switch P-Board Main Input, Power Supply V-Board Remote Receiver, LED IR, Cats

Setting Inspection

Voltage Confirmation

AP board

Description Test point Position Normal mode Stand by mode

Sound_Vcc T P7302 AP3, pin 2,3 15V +/- 0,8V Max 5V DTV_9V TP7502 AP3, pin 17,18 9,1V +/- 0,45V Max 3V Sub_5V TP7402 AP3, pin 21,22 5,1V +/- 0,25V Max 2V Main_9V AP3, pin 23 9,1V +/- 0,45V Max 3V LCD_3.3V TP7602 AP4, pin 16,17 3,3V +/- 0,16V Max 2V STB_5V TP7103 AP4, pin 3 5,1V +/- 0,25V 5,1V +/- 0,25V Panel 12V TP7702 AP4, pin 11,12 12,2V +/- 0,6V Max 4V

P board

5Vs TP823 P8, pin 1 5,1V +/- 0,25V 5,1V +/- 0,25V 24V TP825 P5, pin 1-3 24V +/- 2V Max 4V

DG board

Sub1,2V TP5601 1,17V - 1,32V Sub1,8V TP5602 1,7V - 1,9V Sub3,3V TP5600 3,14V - 3,46V MHQ1,2V TP4209 1,1V - 1,3V

K-BOARD

P-BOARD

V-BOARD

Confirm the following voltages:

9

Self Check

p

Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button.

TX-26LX70F

TX-26LX70L

TX-26LX70P

TX-32LX70F

26 Panasonic 2007LCD 26lxd70.dat:00004f

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

26 Panasonic 2007LCD 26lxd70.dat:00004f

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

26 Panasonic 2007LCD 26lxd70.dat:00004f

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

32 Panasonic 2007LCD 32lxd70.dat:000054

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0010 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0017 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0011 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0006 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

lete

SUM 186d OPTION 1 0c

OPTION 2 ea OPTION 3 7f CHECK 75

MODEL ID 04 030e0000 00000002

lete

SUM 1891 OPTION 1 2c

OPTION 2 ea OPTION 3 7f CHECK 95

MODEL ID 04 030e0000 00000002

lete

SUM 188e OPTION 1 2c

OPTION 2 ea OPTION 3 7f CHECK 95

MODEL ID 04 030e0000 00000002

lete

SUM 1863 OPTION 1 0c

OPTION 2 ea OPTION 3 7f CHECK 75

MODEL ID 04 030e0000 00000004

TX-32LX70L

32 Panasonic 2007LCD 32lxd70.dat:000054

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0016 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

lete

SUM 1891 OPTION 1 2c

OPTION 2 ea OPTION 3 7f CHECK 95

MODEL ID 04 030e0000 00000004

10

p

TX-32LX70P

32 Panasonic 2007LCD 32lxd70.dat:000054

Self Check Com

ADV O.K. VSW O.K. ADAV O.K. ASW O.K. GENX O.K. MEM1 O.K. MEM2 O.K. TUN1 O.K. HQ1L O.K.

PEAKS-SOFT 2.020 PEAKS-EEP 02.00.0007 GenX-SOFT 1.00.00 GenX-EEP 1.02.00 GenX-ROMCORR 1.01.00 HQ1L-EEP 20

lete

SUM 1884 OPTION 1 2c

OPTION 2 ea OPTION 3 7f CHECK 75

MODEL ID 04 030e0000 00000004

Display Ref. No. Description P.C.B.

ADV IC4510 A/D CONVERTER DG-Board

VSW IC3001 VIDEO SWITCH H-Board

ADAV IC2106 AUDIO PROCESSOR H-Board

ASW IC3101 AUDIO SWITCH H-Board

GENX IC1100 MICROPROCESSOR DG-Board MEM1 IC1101 EEPROM DG-Board MEM2 IC8601 EEPROM DG-Board

TUN1 TU3200 ANALOG TUNER H-Board

HQ1L IC4200 HQ1L DG-Board

If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".

11

Power LED blinking timing chart

1. Subject Information of LED Flashing timing chart.

2. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.

Blinking

times

Once

1 INVERTER_SOS

Blinking timing Contents Check p oint

4 sec

Light No Light

DG BOARD

LCD PANEL

2 FAN_SOS

3

4 DTV_9V

5 MAIN_9V

6 SUB_5V

7 MAIN_5V DG BOARD

8 MAIN_3.3V DG BOARD

9 SOUND_SOS

BT_30V,SOUND 15V

PANEL 12V, HQ_ 3.3V

H BOARD

DG BOARD

H BOARD

AP BOARD,DG BOARD

AP BOARD

H BOARD, DG BOARD

AP BOARD

H BOARD, DG BOARD

AP BOARD

H BOARD, DG BOARD

H BOARD

DG BOARD

10 HQ1L_SOS DG BOARD

12

Service Mode Function

MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu

How to enter SERVICE

While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds. Note:

To exit from Service mode, press the exit button on remote control.

0

13

SERVICE

A

SERVICE ADJUST WB-ADJ OPTION SRV-TOOL

Peaks SOFT 2.020 OPTION 1 0c Peaks EEP 02.00.0006 OPTION 2 ea

S e r v i c e 1

LSI DATA 0.00.54 OPTION 3 7f GenX SOFT 1.00.00 Model ID 04 GenX SOFT 1.02.00 030e0000 GenX ROMCOR 0.01.00 00000004 HQ1L EEP 20 Time 00016:00

Count 0000045

1

ADJUST DYNAMIC CONTRAST YMAX

1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT YELLOW:AUTO ADJUST VOL:ADJUST OK :WRITE

1

WB-ADJ DYNAMIC R-GAIN

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

1

OPTION DYNAMIC Boot

1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST

1

SRV-TOOL DYNAMIC

1,2:MAIN SELECT 9 :PICTURE MENU SELECT OK :ENTER

22C

FA

ROM

00

2

3

4

2

3

4

2

3

4

2

ADJUST DYNAMIC COLOR

1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

WB-ADJ DYNAMIC G-GAIN

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC STBY-SET

1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT OK :POWER OFF

3C

FF

00

216

DJUST DYNAMIC

3

TINT

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

WB-ADJ DYNAMIC B-GAIN

3

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT

4

7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC Emergency

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST

Key Command

• Press the 3/4 button to change the adjustment values or function.

• Press the 1/2 button to step up/down through the functions and adjustments

• Press the numerical button VOLUME (+/-) to change of e ach option item.

• Press the OK button after each adjustment has been made to store the required values.

ON

00

F1

ADJUST DYNAMIC

3

SUB-BRT

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

WB-ADJ DYNAMIC R-CENT

3

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT

4

7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC Y/C Delay

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

808

CD

DJUST DYNAMIC

3

BACKLIGHT

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

WB-ADJ DYNAMIC G-CENT

3

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC OPT 1

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

276

80

00001100

DJUST DYNAMIC

H-POS

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

WB-ADJ DYNAMIC B-CENT

3

COLOR TEMP COOL

1,2:MAIN SELECT 3,4:SUB SELECT

4 4

7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC OPT 2

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

11101010

6A

DJUST DYNAMIC

0

H-AMP

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

OPTION DYNAMIC OPT 3

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

0

01111111

ADJUST DYNAMIC V-POS

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

DJUST DYNAMIC

0

V-AMP

3

1,2:MAIN SELECT

4

3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE

0

14

Option Bytes Description

OPTION1

0 Speed ATP Slow (1) / Fast (0) 1 TXT Ch ON (1) / OFF (0) 2 ID-1 ON (1) / OFF (0) 3 Macrovision Auto evaluate ON (1) / OFF (0) 4 SRS Surround ON (1) / OFF (0) 5 Teletext Top OFF (1) / ON (0) 6 Not use 7 Not use

OPTION2

0 Not use 1 A2 Stereo (5,5MHz) ON (1) / OFF (0) 2 A2 Stereo (6,0MHz) ON (1) / OFF (0) 3 A2 Stereo (6,5MHz) ON (1) / OFF (0) 4 Not use 5 NICAM (5,5MHz) ON (1) / OFF (0) 6 NICAM (6,0MHz) ON (1) / OFF (0) 7 NICAM (6,5MHz) ON (1) / OFF (0)

OPTION3

0 NICAM priority (ASIA/M.E) ON (1) / OFF (0) 1 NICAM priority (K/UK) ON (1) / OFF (0) 2 NICAM priority (China) ON (1) / OFF (0) 3 NICAM priority (NZ/INDN) ON (1) / OFF (0) 4 NICAM priority (AUS) ON (1) / OFF (0) 5 NICAM priority (E.Evropa) ON (1) / OFF (0) 6 NICAM priority (Special) ON (1) / OFF (0) 7 Not use

15

Adjustment Method

Sub-Contrast/White Balance Adjustment

Instrument Name Connect to Remarks

1. Remote controller

2. LCD WB meter (Minolta CA-210 or eq uivalent)

3. Comunication jig

4. Computer for external control

Procedure Remarks

Subcontrast adjustment

1. Receive PAL colour bar (10 0% white) RF signal.

2. Enter “Contrast” adj. In SERVICE mode.

3. Start adjusting by using Yellow Key.

4. If the adjustment finished normally, the letter of Contrast will change from red to black.

White Balance adjustment

1. Procedure basically performs checking using the production software and make automatic adjustment using external computer.

2. It adjusts in the mode of: Colour balance Normal

Viewing Mode Dynamic LX70L LX70F, LX70P WHITE Normal WHITE Normal

x: 0,2850 ± 0,010 x: 0,2850 ± 0,010 y: 0,3020 ± 0,010 y: 0,2930 ± 0,010

GRAY Normal GRAY Normal x: 0,2890 ± 0,010 x: 0,2850 ± 0,010 y: 0,3150 ± 0,010 y: 0,2930 ± 0,010

Correlation can be also taken by CS-1000A or equivalent

Let the panel standfor more than 3 hours at more than 20 °C. Basically perform adjustment in the ambient environment of room temperature more than 20 °C. The aging time is more than20 min at above room temperature.

Applied signal 100% full colour bar

0,7V p-p white peak

87.5% modulation

100% WHITE

50% GRAY

16

Wiring diagram

S

O

MAINS IN

P11

K-BOARD

K8

P8

P-BOARD

P5

P10

P9

LCD PANEL

HDMI2

HDMI1

DG27

T L

D

JK8801

SERVICE

DG25

JK4500

JK4501

DG-BOARD

DG33

SERVICE

DG1

V1

V-BOARD

DG6

DG2

H6

H2

AP5

AP7

AP4

H4A

H-BOARD

AP-BOARD

AP6

KEY

AP3

H3A

AV1

AV2

H12

SP

JK2002

UDIO OUT

JK3001

PC AUDIO IN

H51

G51

G-BOARD

V3

JK3005

YPBPR, AUDIO IN

JK3700

17

Video & Stereo Audio Block Diagram

V

Y

V

A

36

A

K

THIS IS EXCHANGE UNIT

JK3002B

JK3003B

H-BOARD

AV1_V 20

AV1_VOUT 19

AV1_RED 15

AV1_GREEN 11

AV1_BLUE 7

AV1_L 6

AV1_LOUT

AV1_R 2

AV1 21PIN SCART

AV1_ROUT 1

AV2_V 20

AV2_VOUT 19

AV2_C 15

AV2 GREEN 11

AV2 BLUE 7

AV2_L 6

AV2_LOUT

AV2_R 2

AV2 21PIN SCART

AV2_ROUT 1

PC

JK3001

2 3 1

1 AV1_V 33 AV1_VO

79 AV1_RED 77 AV1_GREEN 81 AV1_BLUE 8,10 AV2_V

3

31 AV2_VO 12 AV2_C

53 AV3_RED/C 51 AV3_GREEN 55 AV3_BLUE

VIDEO SWITCH

MAIN_RGB_CVBS_OUT 44

IC3001

PC_R 75 PC_G 71 PC_B

PC_H_IN 60 PC_V_IN 58

MAIN_Y_OUT 40

MAIN_PB_OUT 39 MAIN_PR_OUT

PC_H 42

PC_V 41

MAIN_RF_CVBS 91

73

38

13

14

Q3200

TUNER

TU3200

21

10

11

AM

SIF_OUT

VIDEO_OUT

MAIN_RGB_CVBS_OUT

MAIN_Y_OUT MAIN_PB_OUT MAIN_PR_OUT

DTV_BCLK

DTV_SDIN DTV_LRCK DTV2_SDIN

HDMI_BCLK

HDMI_SDIN

HDMI_LRCK

SPDF_IN

H6

3 5 7

10

PC_H

14

PC_V PC_V

16

58 60 62

64 66

68

70 72

DG6

3 5 7

10 14 16

58 60

62 64 66 68 70

72

DG-BOARD

MAIN_Y/CVBS MAIN_PB/C MAIN_PR RGB_CVBS PC_H

DTV_BCKL DTV_SDIN DTV_LRCK DTV2_SDIN

HDMI_BCLK HDMI_SDIN HDMI_LRCK SPDIF_IN

Q4516 Q4515 Q4514

Q4519 Q4517

99 Y_IN 78 PB/C 94 PR 80 RGB_CVBS 97 SOY

63 PC_HS 62 PC_VS

8 HDMI_BCLK 3 HDMI_SDIN 7 HDMI_LRCK

16,17,18,24-33, 38-48,51-53,55,58

IC4510

ADV7493BBSTZ

IC8554

NOR FLASH

3

63 YPBPR_Y

65 YPBPR_PB

67 YPBPR_PR

95 AV4_

97 AV4_

99 AV4_C

AUDIOOUT_L

AUDIOOUT_R

Q2015

Q2021

7 6 1

IC2011

AUDIO

AMPLIFIER

112,113,115,116,

118,119,121,122

L

DTV_BCKL DTV_SDIN

JK2002

R

AUDIO OUT

Q2017

DTV_LRCK DTV2_SDIN

SPDIF_IN

Q2016

D13 A13 F14 D15 A10

A15,A16,B15,B16,C15,C16, D3,D5,D6,E4,E7-E11,E16, F4,F5,F7-F10,F16

CLK,CLKOA,VSYNC,HSYNC,ENB

VI1P2-VI1P9,VI1P12-VI1P19,VI1P22-VI1P29

A2-A9,B1,B3-B10,C1,C2, C4-C10,D1,D2,E2,E3

IC8001-PeaksLite2

MN2WS0039A

17-A23,C17-C22 E17-E20,B17-B22 F17-F19,D20

2

Y PB PR

JK3005

L R

YPBPR, AUDIO IN

R

L

JK3700

AV4_R AV4_L

AV4_V

AV4_Y

Y

AV4_C

C

YPBPR_Y

YPBPR_PB

YPBPR_PR PC_LIN

PC_RIN

PC_LIN 10

PC_RIN 11

H51

G51

7 AV4_R

15

AV2_RO 26

IC3101

AUDIO SWITCH

6 AV4_L

10 8 15

19

7

13

11

AV2_R 15

AV2_L 14

AV2_LO 25

AV_R 33

17

5

AV1_R 17

AV1_LO 23

AV1_RO 24

TV_L 41

TV_R 42

AV_L 32

9

7

3

1

AUXOUTL1 72

76 AINL2 77 AINR2

AV1_L 16

5

3

IC2012

HP

AMPLIFIER

7

HP_ROUT

HP_LOUT

58 HPOUTR1

57 HPOUTL1 74 AUXOUTL2 75 AUXOUTR2

79 AV_R 78 AV_L

8

SIF_IN1

DTV_SDIN 24

DTV_LRCK 18

43

H12

DTV_BCLK 19

IC2106

AUDIO

PROCESSOR

43 SQ_L-

42 SQ_L+

IC2301

AUDIO

AMPLIFIER

36

1

2

DTV2_SDIN 23

AUXOUTR1 73

SPDIF_IN 39

HDMI_SDIN 22

HDMI_BCLK 27

HDMI_LRCK 26

45 SQ_R-

44 SQ_R+

81618

6

31

24

3

4

HDMI 1

JK4501

HDMI 2

JK4500

27,28,30,31 33,34,39,40

IC4503

C1AB00002641

HDMI SWITCH

3,4,6,7,9,10, 45,46

13,14,16,17

RXA_CN,CP,0N,0P,1N,1P,2N,2P

20,21,23,24

SP_R SP_L

IC8002

DDR2-0 SDRAM

IC8003

DDR2-1 SDRAM

IC4201

DDR

SDRAM

LOSD0-LOSD15

LOSD_HP,YS,YM,CLK,

C25,C26,D24-D26,E24-E26, F24-F26,G24-G26,H25,H26, J26,K25,K26,L24-L26,M26

A3-A6,A8-A11,B2-B6,B8-B10,C1-C9

7,8,9,10,51,52,53,54,57,58, 59,60,61,62,63,64,65,66,67, 68,69,70,73,74,75,76,77,78,

LVDS TRANSMITTER

29 30

28 4927

34

32

31

IC4200

MB87Q1431PB

HQ1L

RGB

LVDS_HS,VS,ENB,CLK

IC4207

37 39

35

RIN0-RIN7,GIN0-GIN7,BIN0-BIN7

16-A24,B17-B21,

B23-B25,C16-C24

40 414243

44

VS,HS,CL

4847

46

L

R

HP_LOUT HP_ROUT

G-BOARD

18

TD2+

13

DG25

TD1+

TCLK1-

TD2-

14

TC2-

TCLK2-

TC2+

TCLK2+

17

16

19

TA2-

TB2-

TA2+

TD1-

TB2+

20

24

23

22

21

TC1+

TCLK1+

29

32

33

30

35

TB1-

36

TA1-

TA1+

TB1+

37

40

38

39

TC1-

TO LCD PANEL

Power Supply Block Diagram

V

A

_

V

8

V

8

V

8

V

A

5

P11

1

MAINS IN

2

D801

P - BOARD

+

F801

LF801

Line

Filter

LF802

2

Line

Filter

3

RL802

D802

1

4

-

4

+

3

2

-

1

8,7

4

5

RL801

Q801

4 6

8

3

RELAY_5V

STB_5V

9

12

T801

24V

1

IC801

3

2

24V

STB_5

2

3

2

IC7301

IC7401

Q7212

24V_DET

Q7203

8

STB_5

5

2

SOUND_Vcc

Q7551

MAIN_9V

Q7214

Q7206

SUB5V AUD3.3V

SUB5V

SIF3.3V MAIN9V

5V

SUB3.3V DVDD1.8

SOUND15V SOUND12V

DTV9V

BT30V

SOS

1

P5

1

AP5

24V

8

REGULATOR

8

REGULATOR

IC7501

8

REGULATOR

IC7601

1

REGULATOR

IC7701

1

REGULATOR

Q7205 Q7208

DC-DC ON/OFF

CONTROL

ALL_OFF_DET

Q7211

Q7202

SUB_ON

AP - BOARD

Q7213

7 Vin

IC2008

REGULATOR

1 Vout

1 Vin

IC2010

REGULATOR

5 Vout

4 Vin

IC2013

3

REGULATOR

5 Vout

7,5 Vin

IC2107

REGULATOR

1 Vout

3 Vin

IC2303

REGULATOR

1 Vout

BT30V_SUPPLY

IC2610

PC801

SUB_5V

Q2639

+15V_S

DTV_9V

MAIN_9V

STB_5V

LCD_3.3V

PANEL_12V

PANEL

12V

DTV9V

DTV9V STB5V

MAIN9V

IC802

P3

2

3 17 18 21 22 23

P4

3

17 16

12

11

8

MUTE SW

Q2033

Q2041

H3A

1,2

3

17

18

21

22

23

H4A

3 17 16

12 11

IC2011

AUD AMP

+15V_S +15V_S

DTV9V DTV9V SUB5V SUB5V

MAIN9V

STB5V LCD3.3V LCD3.3V

P12V P12V

5VS

V+

V-

P10

1

3

P8

4 3 1

P9

5 6

7 8

+15V_S SOUND15V

SOUND15V

SOUND12V

SUB5V

BT30V

5V

DTV9V

DVDD1.8V SIF3.3V SUB3.3V

UD3.3V

TO INVERTER

K8

4 3 1

TO INVERTER

LCF

26,27,32,35,40,41

1,21,22,23,44

6,25, 45,69

14,21,31,40,51 12

29 4,53,59,68,71

K - BOARD

RELAY_5 STB_5V

5VS

IC2301

AUD AMP

5,9,16

TU3200

18

IC2012

8

HP AMP

IC3101

5

AUD SWITCH

IC3001

VIDEO SWITCH

IC2106

AUDIO PROCESSOR

SW7000

H - BOARD

PHOTO COUPLER

Q1002 Q1004

REMOTE CONTROL

LED RECEIVER

LCD3.3V LCD3.3V

P12V P12V

DTV9V DTV9V

SUB5V SUB5V

SUB5V SUB3.3V SUB3.3V

MAIN9V

STB5V

CATS-AI

PC1001

R&G LED

RM1001

H2

1 2 5 6 8

9

12

13

14 17 18 21 23

V - BOARD

SUB5V

DG2

1 2 5 6 8

9

12 13 14 17 18 21 23

V1

2 4

MAIN5V

MHQLV3.3V

MAIN5V

MAIN3.3V

MAIN5V MAIN3.3

MAIN5V

MAIN3.3

DTV9V SUB3.3V

SUB5V MAIN5 V

SUB5V

DVDDIO3.3V

HQ3.3V MHQDDR2.5V

SUB5V MHQPL3.3V

HQ3.3 MHQPL1.2

HQ3.3V MHQDDR1.2V

LCD3.3V

HQ3.3V

DG1

12

4

8

1

17

DC/DC CONVER

23

3,8

COMPARATOR

1 Vin

5 Vout

2 Vin 4 Vout

1 Vin 5 Vout

1 Vin

5 Vout

1 Vin 5 Vout

LCF

SUB5V

STB3.3V

IC4500

EEPROM

IC4209

EEPROM

IC4501

EEPROM

IC4504

EEPROM

IC4513

BUS REP

IC4514

BUS REP

IC5600

IC4515

IC4507

REGULATOR

IC4203

REGULATOR

IC4204

REGULATOR

IC4205

REGULATOR

IC4206

REGULATOR

SUB3.3V

3.3V

1.8V

MHQ1.2V

MHQDDR2.5V MHQLV3.3V MHQPL1.2V

MHQPL3.3V MHQDDR1.2V

1.8V_DDRI/F

SUB3.3V SUB1.2V

SUB1.8V

DTV9V SUB1.8V SUB1.2V

DTV9V SUB3.3V

SUB3.3

STB3.3

MAIN3.3

SUB5V

MHQLV3.3

SUB5V

3.3V SUB3.3V

1.8V STB5 SUB5V

STB3.3V

SUB3.3V DVDD1.8V

DTV9V

MHQ1.2V

DVDDIO_3.3V AVDD_3.3V

TVDD_3.3V

CVDD_1.8V PVDD_1.8V DVDD_1.8V

IC8001-PeksLite2

23

IC5601

3

DC/DC CONVER

12

2

IC5660

RESET IC

1

IC8004

5,13,15

IC8601

8

EEPROM

IC1101

IC4503

HDMI RECEIVER

2,11,18,19,26,35, 37,38,42,43,47,48

4 Vin

IC4208

REGULATOR

5 Vout

7 Vin

IC4506

REGULATOR

1 Vout

8 Vin

IC4508

REGULATOR

1 Vout

1 Vin

IC5670

REGULATOR

5 Vout

8 Vin

IC4509

REGULATOR

1 Vout

1,8 Vin

IC4202

REGULATOR

2 Vout

15,35,50,67 84,88

111,123,127,139

104,109,125,141 68,71,101 23,57,142

VDD/1.2V

DDE25/2.5V

VDDE33/3.3V

PLL_SYS ,PLL_OUT

PLL_OUT

PLL_DDR

MN2WS0039A

CLK GEN

EEPROM

IC4510

ADV7493BBSTZ

IC4200

MB87Q1431PB

HQ1L

STB3.3

SUB3.3V

MAIN3.3V

SUB5V MAIN5V

SUB1.8V

1.8V_DDRI/F

STB5V

SUB3.3V

31,50,74,78 81,85,94,108,

Q5693

Q5692

L8003

2

20

53,43,29

SERVICE

JK8801

4

SUB3.3V

IC4201

DDR

D7,D8,E4,E11,L4,L7,L8, L11,C3-C5,C7,C8,C10-C12, E3,E12,F4,F11,G4,G11,J4, J11,K4,K11,H4,H11

IC8003

DDR2-1

A1,E1,M9,J9,R1,J1,J2,A9,C1, C3,C7,C9,E9,G1,G3,G7,G9

IC8002

DDR2-0

A1,E1,M9,J9,R1,J1,J2A9,C1, C3,C7,C9,E9,G1,G3,G7,G9

3,24,55,71,87

IC5671

IC RESET

IC8621

LVO

IC8622

LVO

IC8554

FLASH

IC4207

IC1100

GENX4

LVDS

DG - BOARD

THIS IS EXCHANGE

MHQDDR2.5

1.8V_DDRI/F

MHQLV_3.3

UNIT

+5V

STB5V

P12V P12V

P12V

JK4501

18

JK4500

18

DG33

1

DG25

1

2 3 4

DG27

1

HDMI 1

HDMI 2

SERVICE

TO LCD PANEL

19

Control Block Diagram

A

AV1_SLOW 8

AV1_QLINK 10

JK3002B

AV1 21PIN SCART

AV2_SLOW 8

AV2_QLINK 10

JK3003B

AV2 21PIN SCART

JK3001

PC AUDIO IN

AUDIO OUT

H - BOARD

AV1_FB 16

AV2_FB 16

13

14

MONITOROUT_MUTE

R

JK2002

L

Q2002 Q2003

PC_H_IN

PC_V_IN

AV2_SLOW

PC_V

PC_H FB AV3_FB AV1_FB PC_V_IN PC_H_IN AV1_SLOW SDA0B_5V SCL0B_5V VIDEO_STATUS

SCL0B_5V SDA0B_5V

AUDIO_MUTE

Q2102

Q2101

SOUND_SOS SDA0B

SCL0B AUDIO_XRST

TV_SUB_ON_DELAY

SDA0B_5V

SDA0B SCL0B_5V SCL0B

MUTE

Q2641

Q2640

4 41 42

46,74 48 49

IC3001

58

VIDEO SWITCH

60 80

83 84 85

IC3101

35

AUDIO SWITCH

36

15

IC2106

PROCESSOR

16 17 50

Q2635

AUDIO

DG - BOARD

FB

H6

PC_H

AMUTE

SOUND_SOS

AMUTE

SOS

MONITOROUT_MUTE

AUDIO_MUTE

SP_MUTE

HDMI_INT2

MONITOROUT_MUTE

AMUTE

SCL0B_5V SDA0B_5V AFC1

Q2301

7 17

5

2

D2637

V1-2 OUT MUTE

Q2004 Q2006

13 14 20

IC2301

AUDIO AMP

IC2012

HP AMP

Q2005 Q2007

MUTE SW

D2028

D2031 D2032 Q2031

Q2040

TUNER

Q2034

Q2039

PC_V SCL0B SDA0B AUDIO_XRST AUDIO_MUTE

TV_SUB_ON_DELAY SP_MUTE SOS SOUND_SOS

AFC1 QLINK_AV2 QLINK_AV3

TUNER_MAIN_ON

TUNER_SUB_ON KEY PANEL_STBY_ON 24V_DET

HDMI_INT2 VIDEO_STATUS

16

54

12 14

28 30 32 33 34 35 38

39

41 44 46 48 49

55 56 74 79

DG6

12 14 16 28

30

32 33 34 35 38

39 41

44 46 48 49 54 55 56 74 79

IC4510

ADV7493B

IC5671

RESET IC

IC8554

NOR FLASH

IC8002

DDR2-0 SDRAM

IC8003

DDR2-1 SDRAM

IC8601

EEPROM

IC4504

EEPROM

IC4513

LEVEL

TRANSLATING

IC4514

LEVEL

TRANSLATING

IC8001

PeaksLite2

IC4503

HDMI SW

IC4501

EEPROM

IC4500

EEPROM

JK4501

HDMI1

JK4500

HDMI2

JK8801

SD CARD

SERVICE

Q2003

AP - BOARD

TV_SOS

TV_MAIN_ON

TV_SUB_ON

PAN_VCC_ON

24V_DET

D7206

ALL_OFF

SOS

TUNER_MAIN_ON

1

H4A

1 6 8

AP4

TV_SOS

TV_MAIN_ON

SOS

Q7206

Q7208

Q7209

DC-DC ON/OFF

CONTROL

SUB_ON

Q7201

PANEL VCC

Q7703

24V_DET

Q7211

ALL_OFF_DET

Q7212

6

TUNER_SUB_ON

8

TV_SUB_ON

KEY

14

KEYSCAN

PAN_VCC_ON

PANEL_STBY_ON

15

KEY

ALL_OFF TV_SUB_ON

24V_DET

H3A

AP3

IC8004

CLK GENERATOR

6

V - BOARD

DG1

24V_DET

RM1001

Q1004 Q1002

PC1001

REMOTE

CATS

OUT

Q1006 Q1007

4

REMOTE

G_LED_ON

R_LED_ON

AI_SENSOR

V1

5

8

7

1

QLINK

D1100 D1102

IC1101

EEPROM

IC5660

RESET IC

IC1100

MICROPROCESOR

IC4200

C1AB00002727

HQ1L

IC4207

LVDS

TRANSMITTER

IC4201

DDR SDRAM

IC4209

EEPROM

DG33

SCL SD

SCL3 SDA3 SCL1 SDA1

SCL2 SDA2

6

10 11

4 5

7 8

SERVICE

9

THIS IS EXCHANGE UNIT

AP6

1

LCD PANEL

AP5

7

9

P - BOARD

P5

7

9

Q802

RL802

P8

2

K - BOARD

K8

2

SW7000

20

Parts Location

The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.

28 21

NOTE:

(UK)

(CONTINENTAL)

20

22

6

4

19 14

18

2

12

3

29 17

23

26

11 27 24

9

15

5

7

25

13

1

16

10

8

21

Replacement Parts List

Components Identified by mark have special characteristics important for safety.

In case of ordering these spare parts, please always add the complete Model-Type number to your order.

RTL (Retention Time Limited) Note:

* When replacing any of these components, use only manufacturers specified parts.

The marking (RTL) indicates that the Retention Time is Limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.

Important Safety Notice

X

The marking (X) indicates that board should be exchanged for service.

DescriptionCct Ref Parts Number DescriptionCct Ref Parts Number

COMMON PARTS

EXPLODED VIEW

SPEAKER 1 EAS12S11F TUNER 2 ENGF7701GF REMOTE CONTROL 3 EUR7651120 CONTROL PANEL ASSY 4 K0RB00500006 80P CONNECTOR COVER 5 K1ZZ00001424 PANASONIC BADGE 6 TBMA216 CLAMPER BRACKET 7 TKK0E9522 CONNECTOR COVER 8 TKP0E16001 AV3 BRACKET 9 TKP0E17101 HDMI COVER 10 TKP0E21601 VESA METAL 11 TKZ0E9420 TUNER BRACKET 12 TMW0E109 P P.C.B. RTL 13 TNPA4116AA AP P.C.B. RTL 14 TNPA4117AA G P.C.B. RTL 15 TNPA4118AA V P.C.B. RTL 16 TNPA4127AD K P.C.B. RTL 17 TNPA4128AA H P.C.B. RTL 18 TNPA4291DD POWER BUTTON ASSY 19 TTP0E0015

MISCELLANEOUS COMPONENTS

BATTERY . R6RC/2P AV3 LABEL . TBM0E0771 REAR AV LABEL . TBM0E0821 REAR AV LABEL/HDMI. TBM0E0834 IR WINDOW . TKP0E17904 HDMI COVER BARRIER. TMK0E940 SCREW . XSN3+6FJ SCREW . XTB4+18JFJK SCREW . XTV3+10JFJK SCREW . XTV3+12JFJK SCREW . XTW3+12TFJ SCREW . XTWT4+Z15DFJ SCREW . XYN4+F6FJ SCREW PEDESTAL . XYN4+J10FJK FERRITE CORE FC01 J0KG00000011

I.C.s

MAIN PS CONTROL IC801 C0DABYY00008 REGULATOR IC802 C0DAAMA00003 MICRO_GENX4 IC1100 MNZSFD7GP42 EEPROM BR24L08F-WE2IC1101 C3EBFC000042 REGULATOR IC2008 C0CBCBE00001

REGULATOR IC2010 C0CBCBC00190 OPERATIONAL AMPLIFIERIC2011 C0ABBB000230 AUDIO AMPLIFIER IC2012 C1BB00000947 REGULATOR IC2013 C0DBGYY00281 AUDIO PROCESSOR IC2106 C1AB00002746

1.8V REGULATOR IC2107 C0DBFFD00003 AUDIO AMPLIFIER IC2301 C1AB00002730 REGULATOR IC2303 C0DBGYY00202 REGULATOR IC2610 C0DBAJB00004 VIDEO SWITCH IC3001 AN15876A-VT AUDIO SWITCH IC3101 AN15862A-VT HQ1L_IC IC4200 C1AB00002727 DDR SDRAM IC4201 C3ABQJ000055 REGULATOR IC4202 C0DBAMH00018

2.5V REGULATOR IC4203 C0DBEHG00006 REGULATOR IC4204 C0CBCBC00190 REGULATOR IC4205 C0CBCAC00269 REGULATOR IC4206 C0CBCAC00269 DUAL LVDS DRIVER IC4207 C0JBCZ000556 REGULATOR IC4208 C0CBCBD00043 EEPROM M24C64-WMN6TPIC4209 C3EBJC000055 2KBIT EEPROM IC4500 C3EBDC000067 2KBIT EEPROM IC4501 C3EBDC000067 HDMI SWITCH IC4503 C1AB00002641 EEPROM M24C04-RMN6TPIC4504 C3EBEY000009 REGULATOR IC4506 C0DBGGF00001 REGULATOR IC4507 C0CBCBC00190 REGULATOR IC4508 C0CBCAD00082 REGULATOR IC4509 C0CBCAD00082 VIDEO DECODER IC4510 C1AB00002753 LEVEL SHIFTER IC4513 C0JBAU000034 LEVEL SHIFTER IC4514 C0JBAU000034 COMPARATOR IC4515 C0BBBA000024 DC/DC CONVERTER IC5600 C0DBAYY00273 DC/DC CONVERTER IC5601 C0DBAYY00274 RESET IC IC5660 C0EBM0000026 REGULATOR IC5670 C0CBCBC00190 RESET IC IC5671 C0EBF0000376 REGULATOR IC7301 C0DAAZH00025 REGULATOR IC7401 C0DAAZH00026 REGULATOR IC7501 C0DAAZH00026 REGULATOR IC7601 C0DAAZG00014 REGULATOR IC7701 C0DAAZG00014 PEAKS LITE 2 IC8001 MN2WS0039A DDR SDRAM IC8002 C3ABRG000080 DDR SDRAM IC8003 C3ABRG000080 CLK GEN IC8004 C0ZBZ0001030 16MB FLASH IC8554 TVRP526-1 LOGIC IC IC8621 C0JBAZ002845

22

FUSES

DIODES

DescriptionCct Ref Parts Number DescriptionCct Ref Parts Number

LOGIC IC IC8622 C0JBAZ002845 PHOTO COUP LER PC801 CNC1S171R PHOTO COUP LER PC1001 B3JB00000026 LED RECEIVER RM1001 PNA4701M05TV

FUSE HOLDER F801-1 K3GE1ZA00010 FUSE HOLDER F801-2 K3GE1ZA00010 AC FUSE F801 K5D502BNA007 FUSE R2856 K5H1622A0023

BRIDGE DIODE D801 B0FBAT000008 BRIDGE DIODE D802 B0EBKT000007 VARISTOR D803 ERZV10V621T2 VARISTOR D804 ERZV10V621T2 DIODE D811 B0HCMM000014 DIODE D812 B0HCMM000014 DIODE D813 MA2J11100L ZENER DIODE D814 MAZ82400ML ZENER DIODE D815 MAZ83600ML ZENER DIODE D816 MAZ83600ML DIODE D817 MAZ80560ML ZENER DIODE D818 MAZ41000MF ZENER DIODE D819 B0BA42500001 DIODE D820 B0ZAZ0000045 DIODE D821 B0JCNG000003 DIODE D822 MA2J11100L DIODE D823 MA2J11100L DIODE D824 B0BA03600021 DIODE D825 B0BA03600021 DIODE D1001 B3CKE0000007 DIODE MA704ATX D1100 MA3X704A0L DIODE MA704ATX D1102 MA3X704A0L DIODE MA704ATX D1107 MA3X704A0L DIODE D1112 MA2J72800L DIODE D1113 MA2J72800L DIODE D2026 MA2J11100L DIODE D2028 MA2J11100L DIODE D2029 MA2J11100L DIODE D2031 MA2J11100L DIODE D2032 MA2J11100L DIODE D2033 MA2J11100L DIODE D2034 MA2J11100L ZENER DIODE D2119 B0BC01100001 DIODE D2189 MA2J11100L DIODE D2301 MA2J11100L DIODE D2302 MA2J11100L ZENER DIODE D2303 MAZ30560HL DIODE D2304 MA2J11100L DIODE D2632 MA2J11100L DIODE D2633 MA2J11100L DIODE D2634 MA3X78900L DIODE D2635 MA2J11100L DIODE D2636 MAZ30470HL DIODE D2637 MA2J11100L ZENER DIODE D2638 B0BC03900015 DIODE D3003 MAZ81400ML DIODE D3004 MAZ81400ML DIODE D3005 MAZ81400ML DIODE D3007 MAZ81400ML DIODE D3008 MAZ81400ML DIODE D3009 MAZ81400ML DIODE D3010 MAZ81400ML DIODE D3011 MAZ81400ML DIODE D3012 MAZ81400ML DIODE D3025 MAZ81400ML DIODE D3027 MAZ81400ML DIODE D3028 MAZ81400ML

DIODE D3030 MAZ81400ML DIODE D3031 MAZ81400ML DIODE D3032 MAZ81400ML DIODE D3038 MAZ81400ML DIODE D3039 MAZ81400ML DIODE D3041 MAZ81400ML DIODE D3042 MAZ81400ML DIODE D3043 MAZ81400ML ZENER DIODE D3044 B0BC01100001 DIODE D3100 MAZ81400ML DIODE D3102 MA2J11100L DIODE D3334 MA2J11100L DIODE D3335 MA2J11100L DIODE D3336 MA2J11100L DIODE D3337 MA2J11100L DIODE D3338 MA2J11100L DIODE D4201 B0JCPD000026 DIODE D4202 MAZ80390LL DIODE D4204 MA3X152K0L DIODE D4208 MA2J11100L DIODE D4450 MAZ30560ML ESD SUPPRESSOR D4500 EZAEG2A50AX ESD SUPPRESSOR D4501 EZAEG2A50AX ESD SUPPRESSOR D4502 EZAEG2A50AX ESD SUPPRESSOR D4503 EZAEG2A50AX ESD SUPPRESSOR D4504 EZAEG2A50AX ESD SUPPRESSOR D4505 EZAEG2A50AX ESD SUPPRESSOR D4506 EZAEG2A50AX ESD SUPPRESSOR D4507 EZAEG2A50AX ESD SUPPRESSOR D4508 EZAEG2A50AX ESD SUPPRESSOR D4509 EZAEG2A50AX ESD SUPPRESSOR D4510 EZAEG2A50AX ESD SUPPRESSOR D4511 EZAEG2A50AX ESD SUPPRESSOR D4512 EZAEG2A50AX DIODE D4513 MAZ30560ML ESD SUPPRESSOR D4514 EZAEG2A50AX DIODE D4515 MAZ30560ML ESD SUPPRESSOR D4516 EZAEG2A50AX ESD SUPPRESSOR D4517 EZAEG2A50AX ESD SUPPRESSOR D4518 EZAEG2A50AX ESD SUPPRESSOR D4519 EZAEG2A50AX ESD SUPPRESSOR D4520 EZAEG2A50AX ESD SUPPRESSOR D4521 EZAEG2A50AX ESD SUPPRESSOR D4522 EZAEG2A50AX ESD SUPPRESSOR D4523 EZAEG2A50AX DIODE D4524 B0HCMM000014 DIODE D4525 B0HCMM000014 DIODE D4526 B0HCMM000014 DIODE D4527 B0HCMM000014 ESD SUPPRESSOR D4528 EZAEG2A50AX DIODE D4532 B0HCMM000014 DIODE D5601 MA22D3900L DIODE D5602 MA22D3900L DIODE D5603 B0JCDD000002 DIODE D5604 B0JCDD000002 DIODE D5605 MA22D3900L DIODE D5606 B0JCDD000002 DIODE D5607 MAZ802400L DIODE D5608 MAZ802400L ZENER DIODE D5609 MAZ80560LL DIODE D5670 MA2J11100L DIODE D5671 B0HCMM000014 DIODE D5673 B0HCMM000014 ZENER DIODE D5690 B0BC6R600005 ZENER DIODE D5691 B0BC6R600005 ZENER DIODE D5692 MAZ80390HL DIODE D7101 MAZ82700ML DIODE D7102 MA2J11100L

23

Panasonic TX-32LX70F, TX-32LX70L, TX-32LX70P, TX-26LX70F, TX-26LX70L Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Specifications

CONTENTS

Safety Precautions

Applicable signals

Service Hints

Chassis Board Layout

Setting Inspection

Self Check

Adjustment Method

Wiring diagram

Parts Location

Replacement Parts List