Thank you for purchasing Panasonic product.
Please read these instructions carefully before using this
product, and save this manual for future use.
This lens can be attached to a 35 mm digital camera that
complies with the Leica Camera AG L-Mount standard
and that is equipped with a full-frame image sensor.
0 L-Mount is a trademark or registered trademark of
Leica Camera AG.
0 Other names, company names, product names
mentioned in this document are trademarks or
registered trademarks of the companies concerned.
Contents
Information for Your Safety .................................... 18
Limited Warranty (ONLY FOR U.S.A.)................... 26
Limited Warranty (ONLY FOR CANADA) .............. 28
English
DVQX1747
17
Information for Your Safety
Keep the unit as far away as possible from electromagnetic
equipment (such as microwave ovens, TVs, video games,
radio transmitters, high-voltage lines etc.).
0
Do not use the camera near cell phones because doing so may
result in noise adversely affecting the pictures and sound.
0 If the camera is adversely affected by electromagnetic
equipment and stops functioning properly, turn the
camera off and remove the battery and/or the
connected AC adaptor. Then reinsert the battery and/or
reconnect the AC adaptor and turn the camera on.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
DVQX1747
18
0 Reorient or relocate the receiving antenna.
0 Increase the separation between the equipment and
receiver.
0 Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
0 Consult the dealer or an experienced radio/TV
technician for help.
Any unauthorized changes or modifications to this equipment
would void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Supplier’s Declaration of Conformity
Trade Name:Panasonic
Model No.:S-X50
Responsible Party:
Support Contact:http://shop.panasonic.com/support
THE FOLLOWING APPLIES ONLY IN CANADA.
CAN ICES-3(B)/NMB-3(B)
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ
07102-5490
-If you see this symbol-
Disposal of Old Equipment
Only for European Union and countries with recycling
systems
This symbol on the products, packaging,
and/or accompanying documents means
that used electrical and electronic products
must not be mixed with general household
waste.
For proper treatment, recovery and recycling
of old products, please take them to
applicable collection points in accordance with your
national legislation.
By disposing of them correctly, you will help to save
valuable resources and prevent any potential negative
effects on human health and the environment.
For more information about collection and recycling,
please contact your local authority.
Penalties may be applicable for incorrect disposal of
this waste, in accordance with national legislation.
Precautions
∫ Lens care
0
Do not subject to strong vibration, shock, or
pressure. These may cause malfunction or damage.
– Don’t press hard on the lens.
0
Take care not to drop or bump the lens when carrying it.
– When carrying the digital camera with the lens
attached, hold both the lens and the digital camera to
carry them.
– Take care not to drop or bump the bag in which you have put
the lens.
0
When there is dirt (water, oil, and fingerprints, etc.) on the
surface of the lens, the images may be affected. Lightly wipe
the surface of the lens with a soft, dry cloth before and after
recording.
0 When the lens is not in use, be sure to attach the lens
cap and lens rear cap to prevent dust and other
particles from accumulating on or entering the lens.
0 To protect the lens contact
points (A), do not do the
following. These may
cause malfunction.
– Touch the lens contact
points.
– Allow the lens contact
points to become dirty.
– Place the lens with its
mount surface facing
down.
DVQX1747
English
19
∫ Dust and splash resistant
SFC0360
1ZE4SX50Z
2134
1GE1Z276Z
RGE1Z276Z
0 The dust and splash resistant of the camera will
not prevent the entry of dust or water droplets
completely. Take the following precautions to
provide satisfactory dust and splash resistant
performance. If the lens is not working properly,
consult the dealer or your nearest Service Center.
– Attach to a digital camera that is dust and splash
resistant.
– When attaching or removing the lens, be careful so
that foreign objects such as sand, dust, and water
droplets do not adhere to or enter the lens mount
rubber, contact points, digital camera and lens.
– If the lens is exposed to water droplets or other
liquids, wipe them off with a soft, dry cloth.
0 To improve the dust and splash resistant performance
of the lens, a lens mount rubber is used in the mount.
– The lens mount rubber will leave scuff marks on the
digital camera mount, but this does not impact
performance.
– For information on changing the lens mount rubber,
contact your nearest Service Center.
DVQX1747
20
∫ Condensation (when the lens is fogged up)
0 Condensation occurs when the ambient temperature or
humidity changes. Please be careful, as it may cause
lens stains, mold and malfunction.
0 If condensation occurs, turn off the digital camera and
leave it for approx. 2 hours. The fog will disappear
naturally when the temperature of the digital camera
becomes close to the ambient temperature.
0 The appearance and specifications of products
described in this document may differ from the actual
products you have purchased due to later
enhancements.
Supplied Accessories
Product numbers correct as of January 2019. These may
be subject to change.
1 Lens pouch
2 Lens hood
3 Lens cap
4 Lens rear cap
¢ Fitted to the lens at the time of purchase.
¢
¢
Names and Functions of
Components
4
5
6
1 Lens surface
2 Focus ring
Switches between AF (auto focus) and MF (manual
focus) by sliding the focus ring forwards or
backwards. (l 23)
Rotates the focus ring to focus when set to MF.
3 Aperture ring
Adjusts the aperture value when you set the digital
camera to Aperture-Priority AE mode or Manual
Exposure mode.
0 If you set the position of the aperture ring to [A],
set the aperture value of the digital camera.
4 Contact points
5 Lens fitting mark
6 Lens mount rubber
Note
0 If the sound of AF operation bothers you during video
recording, it is recommended to slide the focus ring to
MF.
English
1
23
DVQX1747
21
Attaching the Lens
For information on how to attach the lens, refer to the
operating instructions for your digital camera.
0 Attach the lens after turning off the digital camera.
0 Attach the lens after removing
the lens rear cap.
0 After removing the lens from
the digital camera, be sure to
attach the lens cap and lens
rear cap to prevent dust and
other particles from
accumulating on or entering
the lens.
∫ Attaching the lens hood
Hold the lens hood with your fingers placed as shown in
the picture.
0Do not hold the
lens hood in a
way that twists
or bends it.
1 Align mark A () on
the lens hood with the
mark on the tip of the
lens.
2 Rotate the lens hood in
the direction of the
arrow to align mark B
( ) on the lens hood
with the mark on the tip
of the lens.
0
Attach the lens hood by
rotating it until it clicks.
∫ Removing the lens hood
While pressing the lens
hood button, rotate the
lens hood in the direction
of the arrow and then
remove it.
22
DVQX1747
Note
AFMF
1.5
0.44 0.6 0.9 1.5 4 ĩ m
23513ft
0 When carrying, the lens hood can be attached in the
reverse direction.
1 Remove the lens hood.
2 Align mark C ( ) on the lens hood with the mark
on the tip of the lens.
3 Attach the lens hood by rotating it in the direction of
the arrow until it clicks.
0
It is recommended to remove the lens hood during flash
photography as the lens hood can block the light from the flash.
0 To prevent dropping of the lens, you should never carry
the lens by just holding the lens hood.
∫ Notes on filter use
0
It is possible to attach the lens cap or the lens hood
with the filter already attached.
0 If you use two or more filters at the same time, part of a
recorded image may darken.
0 It is not possible to attach any items other than filters
such as a conversion lens or adaptor to the front of the
lens and use it in combination with this lens.
Lens damage may result if such items are attached.
Switching AF/MF
Switch AF/MF by sliding the
focus ring
backwards (focus clutch
mechanism).
0 When the digital camera is
0 Check the length indication
0 You can set the amount that
A
forwards or
set to MF, the operation will
be MF irrespective of the
position of the focus ring.
B when using MF. Use it as a
guide for focusing.
the focus moves with the
focus ring using menu
settings in compatible digital
cameras. Switch the lens to
AF and set the digital camera to MF. Refer to the
operating instructions for the digital camera for details.
DVQX1747
English
23
Cautions for Use
0 Do not spray the lens with insecticides or volatile
chemicals.
– If such substances get onto the lens they can
damage the exterior case or cause the paint to peel.
0 Do not point the lens at the sun or other strong
light sources.
– This may cause the lens to collect an excessive
amount of light, resulting in fire and malfunction.
0 Do not use while directly touching the lens at low
temperatures for a long period of time.
– In cold places (environments below 0 oC (32 oF), such
as ski slopes), prolonged direct contact with the metal
parts of the lens may cause skin injury. Use gloves or
similar when using the lens for long periods.
0 Use a soft, dry, dust-free cloth to clean the lens.
– Do not use benzine, thinner, alcohol or other similar
cleaning agents to clean the lens. Using solvents
may damage the lens or cause the paint to peel.
– Do not use a household detergent or a chemically
treated cloth.
0 Do not keep products made of rubber, PVC or similar
materials in contact with the lens for a long period of
time.
0 Do not disassemble or alter this product.
0 When the lens is not going to be used for a prolonged
period, we recommend storing with a desiccant (silica
gel).
DVQX1747
24
0 Check all the parts before recording when you have not
used the lens for a long period of time.
0 Avoid using or storing the lens in any of the following
locations as this may cause problems in operation or
malfunctioning:
– In direct sunlight or on a beach in summer
– In locations with high temperatures and humidity
levels or severe changes in temperature and
humidity
– In sandy or dusty locations
– Where there is fire
– Near heaters, air conditioners or humidifiers
– Where water may make the lens wet
– Where there is vibration
– Inside a vehicle
0 Refer also to the operating instructions for the digital
camera.
Troubleshooting
A rattling sound, etc. is heard when the digital
camera is turned on or off or the lens is shaken.
There is a sound from the lens when taking pictures.
0 This is the sound of the lens moving and aperture
operation. It is not a malfunction.
Specifications
The specifications are subject to change for performance enhancement.
INTERCHANGEABLE LENS FOR DIGITAL CAMERA “LUMIX S PRO 50 mm F1.4”
MountLeica Camera AG L-Mount
Focal lengthf=50 mm
Lens construction13 elements in 11 groups (2 aspherical lenses, 3 ED lenses)
Aperture type11 diaphragm blades/Circular aperture diaphragm
Maximum apertureF1.4
Minimum aperture valueF16
Angle of view47o
Recording range0.44 m (1.44 feet) to ¶ (from the focus distance reference line)
Maximum image
magnification
Image stabilizerNo
Filter diameter77 mm
Maximum diameter‰90 mm (3.5q)
Overall length
Mass (Weight)Approx. 955 g (2.105 lb)
Dust and splash resistant Ye s
Recommended operating
temperature
Permissible relative
humidity
0.15k
Approx. 130 mm (5.1q) (from the tip of the lens to the base side of the lens mount)
j10 oC to 40 oC (14 oF to 104 oF)
10%RH to 80%RH
English
DVQX1747
25
Limited Warranty
(ONLY FOR U.S.A.)
Panasonic Products Limited Warranty
Limited Warranty Coverage (For USA Only)
If your product does not work properly because of a
defect in materials or workmanship, Panasonic
Corporation of North America (referred to as “the
warrantor”) will, for the length of the period indicated on
the chart below, which starts with the date of original
purchase (“warranty period”), at its option either (a) repair
your product with new or refurbished parts, (b) replace it
with a new or a refurbished equivalent value product, or
(c) refund your purchase price. The decision to repair,
replace or refund will be made by the warrantor.
Product or part namePartsLabor
Interchangeable Lens for
Digital Camera
All included Accessories
(Except
Non-Rechargeable
Batteries)
Only Non-Rechargeable
Batteries
During the “Labor” warranty period there will be no
charge for labor. During the “Parts” warranty period,
there will be no charge for parts. This Limited Warranty
excludes both parts and labor for non-rechargeable
DVQX1747
26
1 Year1 Year
90 Days
10 Days
Not
Applicable
Not
Applicable
batteries, antennas, and cosmetic parts (cabinet). This
warranty only applies to products purchased and
serviced in the United States. This warranty is extended
only to the original purchaser of a new product which was
not sold “as is”.
Mail-In Service
Online Repair Request
To submit a new repair request and for quick repair status
visit our Web Site at http://shop.panasonic.com/support
When shipping the unit, carefully pack, include all
supplied accessories listed in the Owner’s Manual, and
send it prepaid, adequately insured and packed well in a
carton box. When shipping Lithium Ion batteries please
visit our Web Site at http://shop.panasonic.com/support
as Panasonic is committed to providing the most up to
date information. Include a letter detailing the complaint,
a return address and provide a daytime phone number
where you can be reached. A valid registered receipt is
required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY
PERIOD, THE PURCHASER WILL BE REQUIRED TO
FURNISH A SALES RECEIPT/PROOF OF PURCHASE
INDICATING DATE OF PURCHASE, AMOUNT PAID
AND PLACE OF PURCHASE. CUSTOMER WILL BE
CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED
WITHOUT SUCH PROOF OF PURCHASE.
--Online Repair Request
.
Limited Warranty Limits and Exclusions
This warranty ONLY COVERS failures due to defects in
materials or workmanship, and DOES NOT COVER
normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not
supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling,
misapplication, alteration, faulty installation, set-up
adjustments, misadjustment of consumer controls,
improper maintenance, power line surge, lightning
damage, modification, introduction of sand, humidity or
liquids, commercial use such as hotel, office, restaurant,
or other business or rental use of the product, or service
by anyone other than a Factory Service Center or other
Authorized Servicer, or damage that is attributable to
acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS
LISTED UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF
ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel
to and from the servicer, loss of or damage to media or
images, data or other memory or recorded content. The
items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY,
ARE LIMITED TO THE PERIOD OF THE LIMITED
WARRANTY.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on
how long an implied warranty lasts, so the exclusions
may not apply to you.
This warranty gives you specific legal rights and you may
also have other rights which vary from state to state. If a
problem with this product develops during or after the
warranty period, you may contact your dealer or Service
Center. If the problem is not handled to your satisfaction,
then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
PARTS AND SERVICE, WHICH ARE NOT COVERED BY
THIS LIMITED WARRANTY, ARE YOUR
RESPONSIBILITY.
English
DVQX1747
27
Limited Warranty
(ONLY FOR CANADA)
28
DVQX1747
As of July 2015
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
Panasonic Canada Inc.
PANASONIC PRODUCT – LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free
from defects in material and workmanship under normal
use and for a period as stated below from the date of
original purchase agrees to, at its option either (a) repair
your product with new or refurbished parts, (b) replace it
with a new or a refurbished equivalent value product, or
(c) refund your purchase price. The decision to repair,
replace or refund will be made by Panasonic Canada Inc.
Interchangeable Lens
for Digital Camera
This warranty is given only to the original purchaser, or
the person for whom it was purchased as a gift, of a
Panasonic brand product mentioned above sold by an
authorized Panasonic dealer in Canada and purchased
and used in Canada, which product was not sold “as is”,
and which product was delivered to you in new condition
in the original packaging.
IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY
SERVICE HEREUNDER, A PURCHASE RECEIPT OR
OTHER PROOF OF DATE OF ORIGINAL PURCHASE,
SHOWING AMOUNT PAID AND PLACE OF PURCHASE
IS REQUIRED
One (1) year, parts and
labour
Loading...
+ 64 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.