Panasonic SA-BT205, SB-HF770, SB-HC300, SB-HS870, SB-HW200 Operating Instructions Manual

RQT9516-R

Operating Instructions

Használati útmutató

Blu-ray Disc Home Theater Sound System

Blu-ray Disc Házimozi Hangrendszer

Model No. SC-BT205

Dear customer

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. To update the firmware of this unit, refer to page 32.

Kedves Vásárló!

Köszönjük, hogy ezt a terméket választotta. A legjobb teljesítmény és biztonság érdekében kérjük, figyelmesen olvassa el a jelen utasításokat. A termék csatlakoztatása, működtetése vagy beállítása előtt kérjük, olvassa végig az utasításokat. Kérjük, őrizze meg ezt a kézikönyvet későbbi használata céljából. Az egység firmware-jének frissítéséhez lásd 32.

Region management information/Régiókezelési tájékoztató

BD-Video This unit plays BD-Video marked with labels containing the region code B.

BD-Video Ez az egység lejátsza az B régiókódot tartalmazó címkével jelölt BD-Video-kat.

Example: Példa:

DVD-Video

This unit plays DVD-Video marked with labels containing the region number “2” or “

ALL”.

DVD-Video

Ez az egység lejátsza az “2” régiószámot vagy “ALL” jelzést tartalmazó címkékkel jelölt DVD-Video-kat.

Example: Példa:

ALL

RQT9516

Accessories

Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts. (Product numbers correct as of March 2009. These may be subject to change.)

(Inside of product)

≥Please note that the actual controls and components, menu

items, etc. of your Blu-ray Disc Home Theater Sound System may look somewhat different from those shown in the illustrations in these Operating Instructions.

≥Operations in these instructions are described mainly with the

remote control, but you can perform the operations on the main unit if the controls are the same.

System SC-BT205 Main unit SA-BT205 Front speakers SB-HF770 Center speaker SB-HC300 Surround speakers SB-HS870 Subwoofer SB-HW200

∏ 1 Remote control

(N2QAKB000073)

∏ 2 Remote control

batteries

∏ 1 Video cable

∏ 1 FM indoor antenna

∏ 1 AC mains lead

≥For use with this unit only.

Do not use it with other equipment. Also, do not use cords from other equipment with this unit.

∏ 1 Speaker cable

(center)

∏ 4 Speaker stands

(with cable)

∏ 4 Bases

∏ 16 Screws

∏ 1 Sheet of speaker

cable stickers

∏ 1 Auto speaker setup

microphone

CAUTION!

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION!

≥DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,

BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.

≥DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS

WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.

≥DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS

LIGHTED CANDLES, ON THE UNIT.

≥DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY

FRIENDLY MANNER.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, ≥DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE,

DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

≥USE ONLY THE RECOMMENDED ACCESSORIES. ≥DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.

This product may receive radio interference caused by mobile telephones during use. If such interference is apparent, please increase separation between the product and the mobile telephone.

The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle.

Getting Started

RQT9516

Safety precautions

Set the unit up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the unit’s service life. Do not place heavy items on the unit.

Do not use high voltage power sources. This can overload the unit and cause a fire. Do not use a DC power source. Check the source carefully when setting the unit up on a ship or other place where DC is used.

Ensure the AC mains lead is connected correctly and not damaged. Poor connection and lead damage can cause fire or electric shock. Do not pull, bend, or place heavy items on the lead. Grasp the plug firmly when unplugging the lead. Pulling the AC mains lead can cause electric shock. Do not handle the plug with wet hands. This can cause electric shock.

Do not let metal objects fall inside the unit. This can cause electric shock or malfunction. Do not let liquids get into the unit. This can cause electric shock or malfunction. If this occurs, immediately disconnect the unit from the power supply and contact your dealer. Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit.

Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons.

Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time.

Unit and media care

Clean discs

Wipe with a damp cloth and then wipe dry.

Disc and card handling precautions

≥Handle discs by the edges to avoid inadvertent scratches or

fingerprints on the disc.

≥Do not attach labels or stickers to discs (This may cause disc

warping, rendering it unusable).

≥Do not write on the label side with a ball-point pen or other writing

instrument.

≥Do not use record cleaning sprays, benzine, thinner, static electricity

prevention liquids or any other solvent.

≥Do not use scratch-proof protectors or covers. ≥Clean any dust, water, or foreign matter from the terminals on the

rear side of the card.

≥Do not use the following discs:

– Discs with exposed adhesive from removed stickers or labels

(rented discs etc). – Discs that are badly warped or cracked. – Irregularly shaped discs, such as heart shapes.

Clean this unit with a soft, dry cloth

≥Never use alcohol, paint thinner or benzine to clean this unit. ≥Before using chemically treated cloth, carefully read the instructions

that came with the cloth.

Observe the following points to ensure continued listening and viewing pleasure.

Dust and dirt may adhere to the unit’s lens over time, making it impossible to play discs. Use the lens cleaner (not included) about once every year, depending on frequency of use and the operating environment. Carefully read the lens cleaner’s instructions before use.

This unit may record information of your operating procedures. If you discard this unit either by disposal or transfer, then follow the procedures to return all the settings to the factory presets to delete the recorded information. (> 48, “To return to the factory preset”) ≥When BD-Video is played back, the operation history may be

recorded in the memory of this unit. The recorded contents differ depending on the disc.

Placement

Voltage

AC mains lead protection

Foreign matter

Service

Disc and card handling

Maintenance

Lens cleaner: RP-CL720E

≥This lens cleaner may not be for sale depending on the region. ≥This lens cleaner is sold as specific for DIGA, but can be used

without problem on this unit as well.

To dispose or transfer this unit

DO NOT

Getting Started

ENGLISH

RQT9516

Table of contents

Accessories........................................................2

Safety precautions.............................................3

Unit and media care...........................................3

Using the remote control ..................................5

Batteries ................................................................. 5

Use .........................................................................5

Control reference guide (remote control)........5

Control reference guide (main unit) .................6

Front panel ............................................................. 6

Rear panel terminals .............................................. 6

Showing START menu.....................................15

Selecting the playback source .......................16

Selecting the source from the START menu ........ 16

Selecting the source by the remote control .......... 16

Enjoying sound from all speakers and

various sound effects....................................17

Enjoying surround sound effects .......................... 17

Changing the sound modes.................................. 17

Adjusting speaker level during play ...................... 17

Basic operation ................................................18

Other operations during play (These functions

may not work depending on the media.) ............ 19

Playing video recorded on a Video Camera or

Video Recorder .................................................. 20

Enjoying BD-LIVE or BONUSVIEW

in BD-Video.....................................................21

Playing secondary video (picture-in-picture) and

secondary audio................................................. 21

Enjoying BD-Live discs with Internet .................... 21

Playing DivX® videos .......................................22

Regarding DivX VOD content............................... 22

Displaying subtitles text........................................ 22

Playing still pictures ........................................23

Useful functions during still picture play ............... 24

Playing music...................................................25

Listening to the Radio .....................................26

Setting up the radio .............................................. 26

Listening/confirming the preset channels ............. 26

RDS broadcasting ................................................ 26

Enjoying TV, etc. with this unit’s speakers ...27

Enjoying TV and other devices sound from

this unit’s speakers............................................. 27

Adjusting the sound .............................................. 27

Making settings for digital audio input ..................27

Linked operations with the TV (VIERA Link

“HDAVI ControlTM”)........................................28

What is VIERA Link “HDAVI Control”? ................. 28

What you can do with “HDAVI Control” ................ 28

Easy control only with VIERA remote control ....... 29

Using the iPod .................................................30

iPod Connection ................................................... 30

iPod Playback....................................................... 31

Enjoying VIERA CASTTM..................................32

Firmware updating........................................... 32

Network settings.............................................. 33

Changing settings with the on-screen menu.... 35

On-screen menu operations ................................. 35

What you can change with the on-screen menu .. 35

Changing the unit’s settings ..........................37

Setup menu operations ........................................ 37

Summary of settings.............................................37

Speaker settings................................................... 41

Wireless connections (optional) ....................42

Connecting the speakers with the optional

wireless system (SH-FX70)................................ 42

Speaker installation option............................. 43

Media (Disc, card and USB device)

information..................................................... 44

Packaged discs .................................................... 44

Recorded discs..................................................... 44

SD cards............................................................... 45

USB device........................................................... 45

Regarding 24p output ........................................... 45

Discs that cannot be played ................................. 45

About MP3/JPEG/DivX files ............................46

Troubleshooting guide.................................... 48

Messages ......................................................... 52

Frequently asked questions ........................... 53

Language code list .......................................... 54

Licenses ........................................................... 54

Glossary ........................................................... 55

Specifications .................................................. 57

Index ............................................................... 118

Getting Started

Assembling the speakers ..............................7

Positioning ......................................................8

Speaker connections......................................9

TV connections .............................................10

Connections with a video cable ...............................10

Connections with a component video cable...........11

Connections with a HDMI cable ...............................11

Connections to a Set Top Box, etc..............12

Radio antenna connections.........................12

Network connection......................................13

AC mains lead connection...........................13

SMART SETUP ..............................................14

Basic setting for the system (SMART SETUP) .......14

Playback

Radio

Other devices

Advanced operations

Optional speaker settings

Reference

Getting Started TV Radio PlaybackOther devices

Advanced operations

Reference Optional speaker

settings

RQT9516

Using the remote control

≥Use alkaline or manganese batteries. ≥Do not mix old and new batteries. ≥Do not use different types at the same time. ≥Do not heat or expose to flame.

≥Do not leave the battery(ies) in an automobile exposed to direct

sunlight for a long period of time with doors and windows closed.

≥Do not take apart or short circuit. ≥Do not attempt to recharge alkaline or manganese batteries. ≥Do not use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire. Remove batteries if the remote control is not going to be used for a long period of time. Store in a cool, dark place.

Aim at the remote control signal sensor (> 6), avoiding obstacles, at a maximum range of 7 m directly in front of the unit. ≥If you cannot operate the unit or other equipment using the remote

control after changing the batteries, please re-enter the codes (> 51).

The distance and the angles are approximate.

Control reference guide (remote control)

1 Turn the unit on and off (> 14) 2 Display Home screen of VIERA CAST (> 32) 3 Select title numbers, etc./Enter numbers or characters (> 19, 34)

(The character buttons may be used when operating VIERA CAST contents.

B 32)

[CANCEL]: Cancel

4 Basic playback control buttons (> 18, 19) 5 Select preset radio stations (> 26) 6 Select surround sound effects (> 17) 7 Show Top menu/Direct Navigator (> 18) 8 [3, 4, 2, 1]: Menu selection

[OK]: Selection [2, 1]: Select preset radio station (> 26) [2] (2;), [1] (;1): Frame-by-frame (> 19)

9 Show OPTION menu (> 19)

[R], [G], [Y], [B] These buttons are used when;

≥

Operating a BD-Video disc that includes JavaTM applications (BD-J). For more information about operating this kind of disc, please read the instructions that came with the disc.

≥

Displaying “Title View”, and “Album View” screens. (Only the [R] and [G] buttons

23)

≥

Operating contents of VIERA CAST (>

32)

;

Show Setup menu (>37)

/Select speaker channel (>

17)

Show status messages (>20)

TV operation buttons You can operate the TV through the unit’s remote control.

[Í] : Turn the television on and off [AV] : Switch the input select [ijVOL]: Adjust the TV volume

> Adjust the volume of the main unit (>

)

? Mute the sound (>

18)

@ Switch on/off Secondary Video (Picture-in-picture) (> 21)

A Select the source

[BD/SD]:Select disc drive or SD card drive (> 16) [iPod]:Select iPod as the source (> 16, 30)

[RADIO/EXT-IN]

:Select FM tuner, USB or external audio as the

source (>

, 26, 27)

B Select radio stations manually (>

26)

C Set the sound mode (>

17)

Show start menu (>15)

Show Pop-up menu (>18)

Return to previous screen

Select audio (>19)

Show on-screen menu (>35)/Set the sleep timer (>20)

Batteries

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

R6/LR6, AA

Insert so the poles ( and ) match those in the remote control.

Press in and lift up.

Replace the lid. When closing the lid, insert it from the  (minus) side.

Use

20˚

30˚

20˚

30˚

Remote control signal sensor

7 m directly in front of the unit

CANCEL

PIP

RETURN

VOL

STOP

1 2 3

4 5 6 7 809

VOL

SKIP

SLOW

SKIP

PLAY

PAU SE

BD/SD

iPod

EXT-IN

MUTE

RADIO

SOUND

SURROUND

OPTION

SLEEP

CH SELECT

SETUP

STATUS

DISPLAY

AUDIO

abc

def

jkl

mno

tuv

ghi

qrs

xyz

Getting Started

RQT9516

Control reference guide (main unit)

Standby/on switch (Í/I) (>14)

Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.

Open or close the disc tray (>18)

SMART SETUP

button

(>14)

Stop (>19)

Start play (>18)

Disc tray (>18)

Connect

iPod (>

30)

SD card slot (>18)

9 Connect Auto speaker setup microphone (> 14)

The indicator lights when there is surround sound effect. (> 17)

;

USB port (>18)

Display

= Select the source

(

16)

BD/DVD )SD )IPOD )FM )USB )AUX )D-IN 1 )D-IN 2

“SD” and “USB” on the unit’s display is not displayed when the SD card or USB device is not in the SD card slot or USB port.

> Skip or slow-search play (> 19)/Select the radio stations (> 26) ? Volume indicator

≥It is possible to set the indicator to turn on/off.

(

38, “FL Display”)

@ Adjust the volume of the main unit (> 18)

≥When pulled hard, the volume knob may come off. ≥To prevent children from swallowing the volume knob, do not pull

off the volume knob.

A Connect headphones (not included) (> 18) B Remote control signal sensor

1 AC IN terminal (> 13) 2 Cooling fan 3 SPEAKERS terminal (> 9) 4 AUX (TV) terminal (> 10, 11)

This terminal can also be used for equipment other than the TV.

5 COMPONENT VIDEO OUT terminal (> 11) 6 OPTICAL DIGITAL IN terminals

Terminal 1(TV) is designated for connection with the TV. (> 10, 11) Terminal 2(STB) can be used for connection with devices other than the STB. (> 12)

7 FM Radio antenna terminal (> 12) 8 Digital transmitter dock (> 42) 9 LAN port (> 13) : HDMI AV OUT terminal (> 11) ; VIDEO OUT terminal (> 10)

Front panel

SMART SETUP

Dock for iPod

OPEN CLOSE

VOLUME

SURROUND OUTPUT

TUNE

SELECTOR

SETUP MIC

SD CARD

Dock for iPod

3 4 5

8 119 10 1412

1817

Pull open.

Rear panel terminals

SPEAKERS

CENTER

3Ω3

FRONT

SURROUND

214

RLR

TRANSMITTER

DIGITAL

AV OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

OPTICAL

2(STB) 1(TV)

DIGITAL IN

FM ANT

75Ω

AUX(TV)

AC IN

WOOFER

SUB-

3 4 5

9 10 11

Getting Started

RQT9516

Assembling the speakers

Front speakers and Surround speakers

Preparation

≥To prevent damage or scratches, lay down a soft cloth and perform

assembly on it.

≥For assembly, use a Phillips-head screwdriver (not included). ≥For wall mount, refer to page 43.

≥You will need to obtain the appropriate screw eyes to match the walls or pillars to which they are going to be fastened. ≥Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have

strong enough support. Improper attachment may result in damage to the wall or speakers.

e.g.

Caution

≥Do not stand on the base. Be cautious when children are near. e.g.

Speaker assembly option

2 Surround speakers

2 Front speakers

4 Stands

(with cables)

4 Bases 16 Screws

Make sure you have all the indicated components before starting assembly, setup, and connection.

Keep the screws out of reach of children to prevent swallowing.

Slide into the groove.

Press into the groove.

Tighten securely.

Position the cable between the ridges.

Leave about 120 mm

Insert the wire fully.

: White : Blue

Push!

Slide into the groove.

Press into the groove.

Tighten securely.

Insert the wire fully.

: White : Blue

Push!

Leave about 120 mm

You can remove and use the cable from the stand. To reattach the cable, refer to page 43.

Thread the speaker cable through the base.

Attach the speaker.

≥Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the

speakers.

NOTE

NOT

Preventing the speakers from falling

Screw eye

(not included)

Wall

Approx. 150 mm

Rear of the speaker

String (not included)

Thread from the wall to the speaker and tie tightly.

DO NOT

Getting Started

RQT9516

Positioning

How you set up your speakers can affect the bass and the sound field.

Setup example

Place the front, center, surround speakers at approximately the same distance from the seating position. Using “SMART SETUP” (>14) is a convenient way to get the ideal surround sound from your speakers when you are unable to place them. The angles in the diagram are approximate.

If irregular colouring occurs on your TV

The center speaker is designed to be used close to a TV, but the picture may be affected with some TVs and setup combinations.

If this occurs, turn the TV off for about 30 minutes.

The demagnetising function of the TV should correct the problem. If it persists, move the speakers further away from the TV.

Caution

Do not touch the front netted area of the speakers. Hold by the sides. e.g. Center speaker

≥This system is a 5.1ch sound system. ≥Place speakers on flat secure bases. ≥Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with thick curtains. ≥For optional wall mount, refer to page 43. ≥Keep your speakers at least 10 mm away from the system for proper ventilation.

NOTE

45º to 60º

120º

Main unit

Surround speakers

Center speaker

Put on a rack or shelf. Vibration caused by the speaker can disrupt the picture if it is placed directly on the TV.

To allow for proper ventilation and to maintain good airflow around the main unit, position it with at least 5 cm of space on all sides.

Subwoofer

Place to the right or left of the TV, on the floor or a sturdy shelf so that it will not cause vibration. Leave about 30 cm from the TV.

Front speakers

Position the speakers as illustrated and place them at the same height or higher than ear level.

Set your surround sound free! Optional Panasonic wireless accessory (SH-FX70)

You can enjoy surround speaker sound wirelessly when you use the optional Panasonic wireless accessory ( SH-FX70). (>42)

For details, please refer to the operating instructions for the optional Panasonic wireless accessory.

≥Use only supplied speakers

Using other speakers can damage the unit, and sound quality will be negatively affected.

≥You can damage your speakers and shorten

their useful life if you play sound at high levels over extended periods.

≥Reduce the volume in the following cases to

avoid damage: – When playing distorted sound. – When the speakers are reverberating due to a

record player, noise from FM broadcasts, or continuous signals from an oscillator, test

disc, or electronic instrument. – When adjusting the sound quality. – When turning the unit on or off.

≥Positioning speakers in front

It is possible to locate all the speakers in front of the listening position. However the optimal surround sound effect may not be obtainable.

NOTE

TIPS

Caution

≥The main unit and supplied speakers are to be used only as

indicated in this setup. Failure to do so may lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance.

≥Do not attempt to attach these speakers to walls using

methods other than those described in this manual.

DO NOT

Getting Started

RQT9516

Speaker connections

Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC mains lead until all other connections are complete.

Setup example

Connect to the terminals of the same colour.

Use of the speaker cable stickers is convenient when making cable connections.

OPTICAL

2(STB) 1(TV)

DIGITAL IN

COMPONENT

VIDEO OUT

VIDEO

OUT

AUX(TV)

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

Main unit

FM ANT

75Ω

WOOFER

SUB-

Sheet of speaker cable stickers

Speaker cable for center speaker (Green)

≥Don’t use a front speaker as a surround speaker or vice versa. Verify the type of speaker with label on the rear label of the speaker

before connecting the appropriate cable.

≥Pay attention to the type of speaker and the connector colour when you place the speakers.

Main unit

Surround speaker (L )

SPEAKERS

CENTER

3Ω3

SUBWOOFER

FRONT

SURROUND

FRONT

Lch

Push!

e.g. Front speaker (L)

e.g.

Speaker cable sticker (included)

: White : Blue

GREY

SURROUND

(Rch)

BLUE

SURROUND

(Lch)

RED

FRONT

(Rch)

WHITE

FRONT

(Lch)

PURPLE

SUBWOOFER

GREEN

CENTER

Insert the wire fully, taking care not to insert beyond the wire insulation.

Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers.

Do not

≥Match the connector colour and the type of speaker as shown above. ≥Extending the speaker cables may damage the speakers and sound quality will negatively be affected.

NOTE

Getting Started

RQT9516

TV connections

For connections with a video cable (> below) For connections with a component video cable (> 11) For connections with a HDMI cable (> 11)

OPTICAL

2(STB) 1(TV)

DIGITAL IN

COMPONENT

VIDEO OUT

VIDEO

OUT

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

Main unit

COMPONENT

VIDEO OUT

VIDEO

OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

OPTICAL

2(STB) 1(TV)

DIGITAL IN

AV OUT

WOOFER

SUB-

AUX(TV)

FM ANT

75Ω

My television has COMPONENT VIDEO IN terminals and HDMI IN terminal. Which should I connect with?

≥The different levels of picture quality input are listed below in order from highest to lowest.

HDMI IN )COMPONENT VIDEO IN )VIDEO IN. However, it will take longer for the picture output to start up when this unit is connected with the HDMI IN terminal. – To enjoy all features of this unit, connect the video cable, even if the component video cable or the HDMI cable is used.

Connections with a video cable

Video cable

If the TV does not have a VIDEO IN terminal, connect using a Scart adapter* (Scart—VIDEO IN). * not included

≥Set “High Clarity Sound” on the on-screen menu to “Off” (> 36).

(Otherwise, the video will not be output.)

Optional connections

≥For those who want to enjoy higher picture quality and have a TV equipped with an HDMI terminal (> 11 ) ≥For those who want to enjoy higher picture quality and have a TV equipped with a COMPONENT VIDEO IN terminal (> 11) ≥For those who have a Set Top Box (Satellite receiver, Cable box, etc.) or video cassette recorder (> 12)

To enjoy TV audio from this home theater system’s speakers

*1You can enjoy the audio from your TV through this home theater system’s speakers by connecting to the “AUX(TV)” terminal or

“OPTICAL 1(TV)” terminal. (> 27)

*2This is the preferred connection for best sound and true surround sound depending on your television.

This unit can decode the surround signals received from your TV. Refer to the operating instructions for the TV for the settings necessary to output its audio from the digital audio output to your home theater system. Only Dolby Digital and PCM can be played with this connection. – After making this connection, make settings to suit the type of audio from your digital equipment (> 27).

COMPONENT

VIDEO OUT

VIDEO

OUT

OPTICAL

2(STB) 1(TV)

DIGITAL IN

OPTICAL

2(STB) 1(T

DIGITAL IN

COMPONENT

VIDEO OUT

YPRPB

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

VIDEO

OUT

WOOFER

SUB-

AUX(TV)

FM ANT

75Ω

AUDIO OUT

VIDEO IN

AUDIO IN

OPTICAL

OUT

VIDEO OUT

AUX(TV)

OPTICAL 1(TV)

Optical digital audio cable*

1,2

(not included)

Audio cable*

(not included) The optical digital audio cable can be used when connecting to televisions with optical out terminals ( right).

Main unit

Video cable

(included)

TIPS

AV1

VIDEO IN

Video cable (included)

Scart adapter (not included)

e.g.

NOTE

TIPS

Getting Started

RQT9516

Do not disconnect the video cable even if the below is connected. Some features may not be displayed.

Connections with a component video cable

≥Connect to terminals of the same colour. ≥Set “High Clarity Sound” on the on-screen menu to “Off” (> 36).

(Otherwise, the video will not be output.)

≥The video output resolution is restricted to “576p/480p” when DVD-Video discs, DivX and BD-Video discs recorded at a rate of 50

field per second are output from the COMPONENT VIDEO OUT terminals.

To enjoy high definition/progressive video

≥Connect to a television that supports 576p/480p or higher. ≥Set “Component Resolution” to “576p/480p”, “720p” or “1080i”. (> 39) ≥Set “HDMI Video Mode” to “Off”. (> 39) Otherwise, the video is output as 480i.

OPTICAL

2(STB) 1(T

DIGITAL IN

COMPONENT

VIDEO OUT

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

VIDEO

OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

OPTICAL

2(STB) 1(TV)

DIGITAL IN

AUX(TV)

WOOFER

SUB-

FM ANT

75Ω

AUDIO OUT

OPTICAL

OUT

COMPONENT

VIDEO IN

AUX(TV)

OPTICAL 1(TV)

COMPONENT VIDEO OUT

Optical digital audio cable*

1,2

(not included)

Audio cable*

(not included) The optical digital audio cable can be used when connecting to televisions with optical out terminals ( right).

Main unit

Component Video cable

(not included)

NOTE

TIPS

Connections with a HDMI cable

≥If there is more than one HDMI terminal, refer to the operating instructions for the TV to determine terminal to connect to. ≥Non-HDMI-compliant cables cannot be utilized. ≥Please use High Speed HDMI Cables that have the HDMI logo (as shown on the cover). It is recommended that you use

Panasonic’s HDMI cable.

Recommended part number: RP-CDHG10 (1.0 m), RP-CDHG15 (1.5 m), RP-CDHG20 (2.0 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m), etc.

≥This unit incorporates HDMI

(V.1.3a with Deep Colour, x.v.ColourTM, High Bit rate Audio) technology. (> 55, 56)

≥When outputting 1080p signal (> 39, “HDMI Video Format”) please use HDMI cables 5.0 meters or less.

NECESSARY SETTINGS

“HDMI Video Mode” : “On”/“HDMI Audio Output” : “Off” (> 39)

With this connection, you can use VIERA Link “HDAVI Control” (> 28).

To enjoy TV audio from this home theater system’s speakers

*1You can enjoy the audio from your TV through this home theater system’s speakers by connecting to the “AUX(TV)” terminal or

“OPTICAL 1(TV)” terminal. (> 27)

*2This is the preferred connection for best sound and true surround sound.

COMPONENT

VIDEO OUT

VIDEO

OUT

OPTICAL

2(STB) 1(TV)

DIGITAL IN

FM ANT

75Ω

OPTICAL

2(STB) 1(T

DIGITAL IN

COMPONENT

VIDEO OUT

SPEAKERS

CENTER

3Ω3

FRONT

SURROUND

AC IN

VIDEO

OUT

AV OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

AUX(TV)

WOOFER

SUB-

OPTICAL

OUT

AV IN

AUDIO OUT

OPTICAL 1(TV)

AUX(TV)

HDMI AV OUT

Optical digital audio cable*

1,2

(not included)

Audio cable*

(not included) The optical digital audio cable can be used when connecting to televisions with optical out terminals ( right).

Main unit

HDMI cable

(not included)

HDMI

compatible

NOTE

TIPS

Getting Started

RQT9516

Connections to a Set Top Box, etc.

Use the following connections when you want to output the original surround audio from your Set Top Box, cable TV, VCR, DVD recorder, etc. through this unit’s speakers.

≥Do not connect through the video cassette recorder.

Due to copy guard protection, the picture may not be displayed properly.

≥Turn off all equipment before connection.

Radio antenna connections

≥This unit can decode the surround signal from the Set Top Box (Satellite receiver, Cable box, etc).

Press [EXT-IN] several times to select

“

D-IN 2” (DIGITAL IN 2*).

* “(CABLE/SAT)” is displayed next to DIGITAL IN 2 when set for CABLE/SAT AUDIO input. (> 28, Setting the TV audio for VIERA

Link “HDAVI Control”)

≥For connections between this unit and the TV, refer to “TV connections” (> 10, 11). ≥If you have various sound sources and this unit’s terminals are not sufficient, connect them to the available inputs on the TV and the

TV output should then be connected to the “AUX(TV)” or “OPTICAL 1(TV)” terminal of the main unit. Refer to the operating instructions of the TV, video cassette recorder, DVD recorder or Set Top Box for settings to output its audio via AUDIO OUT or OPTICAL OUT terminal of the TV. – In some cases the audio signal will only be out as 2ch audio from the TV. In this case, connect the Set Top Box (Satellite receiver,

Cable box, etc.) that will be used most commonly with multi-channel audio to this unit’s “OPTICAL 2(STB)” terminal.

COMPONENT

VIDEO OUT

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

VIDEO

OUT

OPTICAL

2(STB)

1(TV)

DIGITAL IN

AUX(TV)

FM ANT

75Ω

OPTICAL

OUT

OPTICAL 2(STB)

Optical digital audio cable

(not included)

STB, VCR, DVD recorder, etc.

Refer to the operating instructions of the respective devices for the optimal connections.

Main unit

WOOFER

SUB-

TIPS

OPTICAL

2(STB) 1(TV)

DIGITAL IN

COMPONENT

VIDEO OUT

VIDEO

OUT

YPRPB

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

AUX(TV)

WOOFER

SUB-

FM ANT

75Ω

Main unit

Using an indoor antenna

Main unit

FM ANT

75 Ω

Adhesive tape

FM indoor antenna

(included) Affix this end of the antenna where reception is best.

Using an outdoor antenna

Main unit

FM outdoor antenna [Using a TV antenna (not included)]

The antenna should be installed by a competent technician.

75  coaxial cable (not included)

FM ANT

75 Ω

Use outdoor antenna if FM radio reception is poor.

≥Disconnect the antenna when the unit is not in use. ≥Do not use the outdoor antenna during an electrical storm.

Getting Started

RQT9516

Network connection

AC mains lead connection

≥Before turning the power on for the first time, be sure to read the preparations for SMART SETUP. (> 14)

The following services can be used when this unit is connected to the internet via a broadband.

≥Firmware can be updated (> 32) ≥You can enjoy the BD-Live (> 21) ≥You can enjoy the VIERA CAST (> 32)

≥When your communication equipment (modem), etc. has no broadband router functions: Connect a broadband router.

When your communication equipment (modem), etc. has broadband router functions but there are no vacant ports: Connect a hub.

≥Use shielded LAN cables when connecting to peripheral devices. ≥Use a router that supports 10BASE-T/100BASE-TX. ≥When operating the VIERA CAST, use high-speed internet service no less than 1.5 Mbps for SD (Standard Definition) and 6 Mbps

for HD (High Definition) picture quality by your local broadband company. – If using slow Internet connection, the video may not be displayed correctly.

≥After connecting to the Internet, perform necessary settings. (> 33) ≥Inserting any cable other than a LAN cable in the LAN terminal can damage the unit.

Main unit

OPTICAL

2(STB) 1(TV)

DIGITAL IN

COMPONENT VIDEO OUT

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

VIDEO

OUT

VIDEO

OUT

AV OUT

AUX(TV)

WOOFER

SUB-

FM ANT

75Ω

LAN

Straight LAN cable (not included)

Internet

Hub or broadband router

Telecommunications equipment (modem, etc.)

NOTE

AC mains lead

Connect only after all other connections are complete.

Conserving power

This unit consumes a small amount of power even when it is turned off (approx. 0.3 W). To save power when the unit is not to be used for a long time, unplug it from the household mains socket. You will need to reset some memory items after plugging in the main unit.

OPTICAL

2(STB) 1(TV)

DIGITAL IN

COMPONENT

VIDEO OUT

SPEAKERS

AV OUT

CENTER

3Ω3

FRONT

SURROUND

AC IN

TRANSMITTER

DIGITAL

VIDEO

OUT

COMPONENT

VIDEO OUT

VIDEO

OUT

Main unit

FM ANT

75Ω

AC mains lead (included)

To a household mains socket

AUX(TV)

WOOFER

SUB-

NOTE

TIPS

Getting Started

RQT9516

SMART SETUP

The SMART SETUP screen assists you to make necessary settings.

When the system is switched on for the first time, the SMART SETUP screen for the basic settings is displayed automatically. Follow the on-screen prompts to make basic settings for the system.

Preparation

To optimize the surround sound experience we recommend that you setup the speaker output level using the Auto speaker setup function.

≥Place the Auto speaker setup microphone at actual seating position.

(At ear level when seated.)

≥A test signal is output from each speaker during the SMART SETUP.

≥After the SMART SETUP is completed, unplug the Auto speaker setup

microphone and keep it for future use.

Preparation

Turn on your TV and select the appropriate video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this unit. ≥To change your TV’s video input mode, refer to its operating

instructions.

≥This remote control can perform some basic TV operations (> 5).

1 Press [

Í].

≥When the SMART SETUP screen appears automatically, skip

step 2 and 3.

2 Press [BD/SD] to select “BD/DVD”. 3 Press [SMART SETUP] on the main unit.

≥The SMART SETUP screen appears.

4 Follow the on-screen instructions and make the

settings with [3, 4, 2, 1] and [OK].

≥Language (> below)

Select the language used on menu screen.

≥TV Aspect (> below)

Select the aspect to suit your TV and preference.

≥Speakers position

Specify the positioning of the surround speakers.

≥Auto Speaker Setup

Adjust the speaker output level automatically.

≥Speaker Output

Make surround sound setting for speaker output.

≥TV Audio

Select the audio input connection from your TV. For AUX connection (> 10): Select “AUX”. For OPTICAL DIGITAL IN connection (> 10): Select “DIGITAL IN 1”. This will be the TV Audio setting for VIERA Link “HDAVI Control”. (> 28)

To return to the previous screen, press [RETURN].

5 Press [OK] to finish the SMART SETUP.

Keep as quiet as possible during the Auto speaker setup. Excessive background noise may lead to incorrect settings. The speakers output loud test signals during setup.

≥Auto Speaker Setup can be activated through SMART

SETUP only.

≥Audio settings will be restored to default if Auto Speaker

Setup is cancelled.

Basic setting for the system (SMART SETUP)

Auto speaker setup microphone

NOTE

≥If this unit is connected to a “HDAVI Control 3 (or later)”

compatible TV via HDMI cable, the menu language and TV aspect information will be retrieved via VIERA Link.

≥If this unit is connected to a “HDAVI Control 2” compatible

TV via HDMI cable, the menu language information will be retrieved via VIERA Link.

≥Even if this unit is connected to a “HDAVI Control 2 (or

later)” compatible TV via HDMI cable, the menu screen language will not be automatically retrieved if this unit does not support the language. In this case, set the language manually.

≥Settings in the SMART SETUP can also be changed in

the unit settings [e.g. language, TV aspect and speaker level (> 37)].

≥Positioning examples for mounting all speakers in front.

(> 8)

RETURN

BD/SD

RETURN

BD/SD

SMART SETUP

TUNE

SELECTORSETUP MIC

SD CARD

TUNE

SELECTOR

TUNE

SELECTORSETUP MIC

SD CARD

SELECTOR

NOTE

Getting Started

RQT9516

Showing START menu

Some functions of this unit can be operated from the START menu.

1 Press [

Í] to turn on the unit.

2 Press [START].

≥Items displayed vary according to the chosen selector and

media.

3 Press [3, 4] to select

the item and pr

ess [OK].

Items Functions

Playback Disc Playback

Starts playing disc/USB device/SD Card.

Top Menu

Shows a disc top menu.

Shows a media menu.

To play AVCHD (> 20) To play MPEG2 (> 20) To play MP3, CD(> 25) To play JPEG (> 23) To play DivX (> 22)

Shows the iPod menu.

To play “Music” (> 31) To play “Videos” (> 31) To play “Use iPod display (All)” (> 31) For “Play Mode” (> 31)

Network

Displays Home screen of VIERA CAST (> 32)

Input Selection

Select the source.

BD/DVD/CD:

To play BD-Video, DVD-Video, AVCHD (> 18-21) To play JPEG (> 23) To play DivX (> 22) To play MP3, CD (> 25)

SD card:

To play AVCHD (> 20) To play MPEG2 (> 20) To play JPEG (> 23)

iPod:

To play iPod contents (> 30)

FM:

To enjoy the FM radio (> 26)

USB device:

To play MP3 (> 25) To play JPEG (> 23) To play DivX (> 22)

AUX (TV)*1:

To enjoy TV broadcasts with this unit’s speakers (> 27)

DIGITAL IN 1 (TV)*

To enjoy TV broadcasts with this unit’s speakers (> 27)

DIGITAL IN 2 (CABLE/SAT)*2:

To enjoy audio from other devices with this unit’s speakers (> 27)

“(TV)” is displayed next to items set for TV AUDIO input. (B 28, Setting the TV audio for VIERA Link “HDAVI Control”)

“(CABLE/SAT)” is displayed next to DIGITAL IN 2 when set for CABLE/SAT AUDIO input. (> 28, Setting the TV audio for VIERA Link “HDAVI Control”)

Sound(Equalizer) Select the equalizer function (> 17) To Others Setup:

You can change the unit’s settings using Setup menu (> 37).

Card Management:

Formatting SD cards/Deleting data (> 21)

Playlists:

You can play playlists created on DVD-VR. Press [3, 4, 2, 1] to select the playlist and press [OK].

START

RETURN

To Others

Playback D isc

Top Men u

Home Cinema

START

BD-Video

Input Selection

Sound(Equalizer)

Network

e.g., [BD-V]

RETURN

DIGITAL IN 1

BD/DVD/CD

SD card

Home Cinema

START

Input Selection

BD-Video

DIGITAL IN 2

iPod

USB device

AUX (TV)

e.g., [BD-V]

Getting Started

RQT9516

Selecting the playback source

Selecting the source from the START menu

You can select sound modes, desired source, or access playback/menus by using the START menu.

1 Press [

Í] to turn on the unit.

2 Press [START] to show the START menu. 3 Press [3, 4] to select the item and then

press [OK].

≥To exit, press [START].

4 Press [3, 4] to make the setting.

When “Input Selection” is selected

You can select a desired source from the menu. ≥BD/DVD/CD, SD card, iPod, FM, USB device, AUX*1,

DIGITAL IN 1

, DIGITAL IN 2*2 (> 15)

“(TV)” is displayed next to items set for TV AUDIO input. (> 28, Setting the TV audio for VIERA Link “HDAVI Control”)

“(CABLE/SAT)” is displayed next to DIGITAL IN 2 when set for CABLE/SAT AUDIO input. (> 28, Setting the TV audio for VIERA Link “HDAVI Control”)

When a disc is loaded, an USB device is connected or a SD card is inserted, you can also access playback or menus from the START menu.

e.g. [BD-V]

Selecting the source by the remote control

Press To select

BD/DVD/CD or SD (> 18)

IPOD (iPod) (> 30)

Each time you press the button:

FM (> 26) USB (> 18) AUX*

: For audio input through the AUX terminal.(> 27)

D-IN1 (DIGITAL IN 1*

): (> 27)

D-IN2 (DIGITAL IN 2*

): (> 27)

*1“(TV)” is displayed next to items set for TV AUDIO input. (> 28,

Setting the TV audio for VIERA Link “HDAVI Control”)

*2“(CABLE/SAT)” is displayed next to DIGITAL IN 2 when set for

CABLE/SAT AUDIO input. (> 28, Setting the TV audio for VIERA Link “HDAVI Control”)

Press [SELECTOR] on the main unit to select source from the main unit.

≥Confirm the audio connection to the AUX or OPTICAL DIGITAL IN

terminals on the main unit when you select the corresponding sources (> 10 to 12).

≥Reduce the volume on the TV to its minimum, and then adjust the

volume of the main unit.

BD/SD

iPod

EXT-IN

RADIO

SELECTOR

RADIO/EXT-INBD/SD

iPod

START

TUNE

SELECTORSETUP MIC

SD CARD

TUNE

SELECTOR

TUNE

SELECTORSETUP MIC

SD CARD

SELECTOR

RETURN

Home Cinema

START

No Disc

Input Selection

Network

To Others

Sound(Equalizer)

RETURN

To Others

Playback D isc

Top Men u

Home Cinema

START

BD-Video

Input Selection

Sound(Equalizer)

Network

Playback/menu access

BD/SD

iPod

EXT-IN

RADIO

NOTE

Getting Started

RQT9516

Enjoying sound from all speakers and various sound effects

≥The following sound effects/modes may not be available or have no effect with some sources, or when headphones are used (> 18). ≥You may experience a reduction in sound quality when these sound effects/modes are used with some sources. If this occurs, turn the sound

effects/modes off.

Press [SURROUND] several times to select the effect.

≥You can also press [SURROUND] and then [3, 4] to select the

mode.

≥The selected effect will only be displayed on the main unit.

When selecting the MANUAL effects.

While “MANUAL” is displayed

Press [

2, 1] and select the desired effect.

≥“NOT CONDITIONAL” is displayed on the main unit if the setting is

not active.

≥“DOLBY PL II MOVIE” and “DOLBY PL II MUSIC” do not work when

audio is output from the HDMI AV OUT terminal.

1 Press [SOUND] several times to select the mode.

≥You can also press [SOUND] and then [3, 4] to select the

mode.

≥The selected effect will only be displayed on the main unit.

2 While the selected mode is displayed

Press [2, 1] and select the desired setting.

1 Press and hold [-CH SELECT] for 3 seconds to

activate the speaker setting mode.

2 Press [-CH SELECT] several times to select the

speaker.

Each time you press the button: LR—) C_) RS_) LS_) SW

^""""""""""""""""""b

L R: Front speaker (left and right) C: Centre speaker RS: Surround speaker (right) LS: Surround speaker (left) SW: Subwoofer

≥The channels not included in the playing audio will not be

displayed (subwoofer is displayed even if it is not included).

(When “L R” selected)

3 Press [2, 1] to adjust the balance of the front

speakers.

(When other speakers are selected)

4 Press [3] (increase) or [4] (decrease) to adjust

the speaker level for each speaker.

s6 dB to r6 dB

Enjoying surround sound effects

Available surround sound effects

Effect Setting

STANDARD: Sound is output as it was recorded/encoded.

Speaker output varies depending on the source.

MULTI-CH: You can enjoy sound from the front speakers, as well

as the surround speakers even when playing a 2-channel sound or non-surround sound.

MANUAL: –DOLBY PL II MOVIE:

Suitable for movie software, or the one recorded in Dolby Surround. (except [DivX])

– DOLBY PL II MUSIC:

Adds 5.1-channel effects to stereo sources. (except [DivX])

– S.SURROUND:

You can enjoy sound from all speakers with stereo sources.

– 2CH STEREO:

You can play any source in stereo. Sound will be output to the front speakers and the subwoofer only.

SOUND

SURROUND

CH SELECT

SURROUND

SOUND

Changing the sound modes

Available sound modes

Mode Setting

EQ: (Equalizer)

You can select sound quality settings. – FLAT(Flat):Cancel (no effect is added). – HEAVY(Heavy):Adds punch to rock. – CLEAR(Clear):Clarifies higher sounds. – SOFT(Soft):For background music.

SUB W: (Subwoofer level)

This unit will change the settings for the amount of bass depending on the source. However you can also adjust the amount of bass for the source being played.

– 1 (Weakest effect) –2 –3 – 4 (Strongest effect)

≥The setting you make is retained, and recalled

every time you play the same type of source.

CF: (Center Focus)

(Effective when playing audio containing center channel sound.)

You can make the sound of the center speaker seem like it is coming from within the TV.

–ON –OFF

W.S.: (Whispermode Surround)

(Effective when playing video with 5.1ch audio.)

You can enhance the surround effect for low volume

5.1-channel sound. (Convenient for late night viewing.)

–ON –OFF

Adjusting speaker level during play

Adjusting the balance of the front speakers

Adjusting the speaker level

Getting Started

RQT9516

Basic operation

∫ To adjust the volume.

It is also possible to adjust the volume with the volume knob on the main unit.

∫ To mute the sound.

Instructions for operations are generally described using the remote control in these operating instructions.

Preparation

Turn on the television and select the appropriate video input on the television.

VOLUME

SURROUND OUTPUT

TUNE

SELECTORSETUP MIC

SD CARD

Stop Play

,VOLUME

Skip/Search/Slow-motion

SD CARD

Headphones (not included) Headphone plug type: ‰3.5 mm stereo mini plug

≥Reduce the volume before connecting. ≥Audio is automatically switched to 2ch

stereo.

≥To prevent hearing damage, avoid

listening for prolonged periods of time. Excessive sound pressure from earphones and headphones can cause hearing loss.

Label facing up

1 Press [< OPEN/CLOSE] to open the disc tray. 2 Insert or remove the disc.

Inserting or removing an SD card

1 Pull to flip down the front panel. 2 Insert the SD card into the SD card slot.

≥To remove the card, press on the center of the card

and pull it straight out.

≥Press [< OPEN/CLOSE] again to close the disc tray. ≥DVD-RAM: Remove discs from their cartridges before use. ≥Insert double-sided discs so the label for the side you want to play is

facing up.

Insert the card label up with the cut-off corner on the right. ≥Press on the

center of the card until it clicks into place.

Inserting or removing a disc

Inserting or removing a USB device

1 Pull to flip down the front panel. 2 Insert the USB device into the USB port.

≥

Before inserting any USB device to this unit, ensure that the data stored therein has been backed up.

≥Check the orientation of the USB connector and insert it straight in. ≥Some USB devices inserted into this unit may cause this unit to stop operating.

Such USB devices cannot be used on this unit.

To remove the USB device, complete all USB device-related operations and pull the USB device straight out.

About the use of USB device

Since the physical size of USB device can vary, please consider its width when connecting any USB device to this unit. It is possible that some devices may accidentally activate the playback button and cause this unit to not operate properly. ≥In such cases we recommend using a USB extension cable (not included).

1 Press [Í] to turn on the unit. 2 Insert the media (D above).

Play start.

≥If play does not start, press [1PLAY]. ≥If

the media with data in different file formats is inserted, the file

selection menu is displayed. Press [3, 4] to select the desired file format and press [OK].

≥If the menu is displayed, press [3, 4, 2, 1] to select the item and

press [OK].

≥If the screen prompting you to use the colour buttons appears,

continue to operate with the colour buttons on the remote control.

Press to adjust the volume

Press to mute the sound

“MUTE” flashes on the unit’s display. ≥To cancel, press [MUTE] again or

adjust the volume.

≥Muting is cancelled if the unit is

turned off.

e.g., Display

VOL

MUTE

≥Signal from PAL discs is output as PAL. Signal from

NTSC discs is output as “NTSC” or “PAL60”. You can select “NTSC” or “PAL60” in “NTSC Contents Output” for NTSC discs. (> 37)

≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE

DISPLAYED. Press [∫STOP] when you finish to preserve the unit’s motor and your television screen.

≥If a media is inserted while the unit is stopped, the drive

switches automatically depending on the inserted media.

≥The producers of the disc can control how discs are

played. So you may not always be able to control play as described in these operating instructions. Read the disc’s instructions carefully.

≥When playing a set of two or more BD-Video discs, the

menu screen may continue to display even if the disc has been ejected.

To display menus

[BD-V] [AVCHD] [DVD-VR] [DVD-V] [DivX]

Press [TOP MENU/DIRECT NAVIGATOR].

To show Pop-up menu [BD-V]

The Pop-up menu is a special feature available with some BD-Video discs. This menu may vary with discs. For the operating method, refer to the instructions for the disc.

1) Press [POP-UP MENU].

2) Press [3, 4, 2, 1] to select the item and press [OK]. ≥Pop-up menu also appears by pressing [OPTION] and

selecting “Pop-up Menu”.

≥Press [POP-UP MENU] to exit the screen. ≥It may take time to read BD-Video discs that include BD-J

(> 55).

NOTE

TIPS

Playback

RQT9516

Other operations during play (These functions may not work depending on the media.)

Stop

The stopped position is memorized.

Resume play function

Press [1PLAY] to restart from this position. ≥The position is cleared if the tray is opened or you press [∫STOP]

several times to display “STOP” on unit’s display.

≥[BD-V]: On BD-Video discs including BD-J (> 55), the resume

play function does not work.

≥[CD] [MP3] [DivX] [MPEG2]: The position is cleared if the unit is turned

off.

Pause

Press [;PAUSE] again or [1PLAY] to restart play.

Search/Slow-motion

The speed increases up to 5 steps.

≥Press [1PLAY] to revert to normal playback speed. ≥For some discs, the speed may not change.

While playing, press [SEARCH6] or [SEARCH5]. ≥[BD-V] [AVCHD] [DVD-VR] [DVD-V]:

Audio is heard during first level of forward search.

≥[DivX] [MPEG2]: Audio is not heard during all levels of search. ≥[CD] [MP3]: The speed is fixed to a single step.

Slow-motion

While paused, press [SEARCH6] or [SEARCH5]. ≥[BD-V] [AVCHD]: Forward direction [SEARCH5] only. ≥[DVD-VR]

If continued for approx. 5 minutes, slow-motion play

pauses automatically.

Skip

Skip to the title, chapter or track you want to play.

≥Each press increases the number of skips. ≥[DivX]: Backward direction [SKIP:] only.

AUDIO

VOL

STOP

123 4 56 7809

SKIP

SLOW

SKIP

PLAY

PAUS E

MUTE

OPTION

abc

def

jkl

mno

tuv

ghi

qrs

xyz

SLEEP

STATUS

RETURN

STOP

PAU SE

SLOW

SKIP SKIP

Direct Play

During playback, you can access specific recordings or scenes through direct entry of the numbered buttons. Play starts from the selected title or chapter.

[BD-V] [AVCHD] e.g., 5: [0]

B [0] B [5]

15: [0] B [1] B [5]

[DVD-V]

e.g., 5: [0] B [5]

15: [1] B [5]

≥While stopped (the image on the right is

displayed on the screen), the title is designated. While playing, the chapter is designated.

Frame-by-frame

While paused, press [2] (2;) or [1] (;1). Each press shows the next frame.

≥Press and hold to change in succession forward or backward. ≥Press [1PLAY] to revert to normal playback speed. ≥[BD-V] [AVCHD]: Forward direction [1] (;1) only.

Changing audio during play

[BD-V] [AVCHD] [DVD-V]

You can change the audio channel number each time you press the button. This allows you to change the soundtrack language (> 35, Soundtrack), etc. ≥[BD-V] When “BD-Video Secondary Audio” (> 38) is set to “On”,

Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio and DTS-HD High Resolution Audio are output as Dolby Digital or DTS Digital Surround regardless of this setting.

[DVD-VR] [DivX] [MPEG2]

AudioLR>AudioL>Audio R

^------------------------------------------}

Chapter playback

[DVD-VR]

1 Insert a disc (> 18). 2 While “Title View” screen is displayed

Press [3, 4] to select the title and press [OPTION].

3 Press [3, 4] to select “Chapter View” and

press [OK].

4 Press [2, 1] to select the chapter and press

[OK].

123 4 56 7809

abc

def

jkl

mno

tuv

ghi

qrs

xyz

AUDIO

Soundtrack

1 ENG Digital 3/2.1ch

English is selected.

e.g. [DVD-V]

PLAY

DVD-RAM(VR)

AudioLR

“AudioLR” is selected

Properties

Chapter View

To Picture

To display the title properties (recording date, etc.)

Playing still pictures (> 23)

To select the chapter

Playback

RQT9516

Basic operation

[AVCHD] [MPEG2] It is possible to playback the High Definition (AVCHD format) video

recorded on a Panasonic High definition Video Camera on a DVD-RAM/R/RW/R DL/+R/+RW/+R DL, or SD card and Standard Definition (MPEG2 format) Video recorded on the Panasonic SD Video Camera on a SD card.

1 Insert a disc or SD card. (

> 18)

≥“Title View” or “Video (MPEG-2)” screen is displayed. ≥If a media containing data in different file formats is inserted, the

file selection menu may be displayed. Press [3, 4] to select “Play Video (AVCHD)” or “Play Video (MPEG-2)” and press [OK].

2 Press [3, 4, 2, 1] to select the title and press

[OK].

Status messages

The status messages give you information about what is currently being played. Each time you press [STATUS], the information displayed will change.

Screen Aspect

When black bars are shown at the top, bottom, left, and right sides of the screen, you can enlarge the image to fill the screen.

1 Press [OPTION]. 2 Press [3, 4] to select “Screen Aspect” and press [OK]. 3 Press [2, 1] to select “Side cut” or “Zoom” and press [OK].

Normal: Normal output Side cut: The black bars on the right and left sides of the 16:9

image disappear and the image is enlarged. Please note that the right and left sides of the image are cut off when the black bar is not displayed.

Zoom: The black bars on the top and bottom sides of the 4:3

image disappear and the image is enlarged. Please note that the top and bottom sides of the image are cut off when the black bar is not displayed.

≥[BD-V] [DVD-V]: “Side cut” does not have any effect. ≥When “TV Aspect” (> 39) is set to “4:3” or “4:3 Letterbox”, the

“Zoom” effect is disabled.

Setting the sleep timer

1 Press and hold [—SLEEP] for 3 seconds. 2 While “SLEEP ££” is displayed,

Press [—SLEEP] several times to select the time (in minutes).

SLEEP 30 ) SLEEP 60 ) SLEEP 90 )SLEEP 120 )OFF

^""""""""""""""""""""""""""""""""b

e.g., Display

To confirm the remaining time

Press and hold [—SLEEP] for 3 seconds.

≥The sleep timer cannot be set while the Setup menu is displayed. ≥The sleep timer will be cancelled in the following cases.

– When the sleep timer is set to “OFF”. – When this unit is turned off from the remote control, main unit or via

the VIERA Link.

STATUS

PLAY

BD-Video

 T1 C1 0:05.14

0:20.52

T: Title C: Chapter

PL: Playlist

Items change depending on the disc played.

No display

Current position

Type of disc

Play status

Elapsed time in the title

e.g. [BD-V]

Depending on the kind of disc or the playback status, this display may not appear.

Tota l t im e

SLEEP

DISPLA

SLP

Playing video recorded on a Video Camera or Video Recorder

≥It may pause for a few seconds between images when

editing such as partial deletion is performed.

≥High definition video (transfer rate of 18 Mbps or faster)

cannot be played back correctly if it was recorded on a DVD compatible to double speed or slower.

To return to the previous screen

Press [RETURN].

To exit the screen

Press [TOP MENU/DIRECT NAVIGATOR].

To switch from other menus to AVCHD or MPEG2 menu

(If the media contains data in different file formats)

1) Press [START].

2) Press [3, 4] to select “Menu” and press [OK].

3) Press [3, 4] to select “Play Video (AVCHD)” or “Play Video (MPEG-2)” and press [OK].

SD CARD

Play Video (AVCHD)

Select an action or press RETURN.

Play Pictures (JPEG)

OK RETURN

OPTION

Play Video (MPEG-2)

e.g. [SD]

NOTE

TIPS

Playback

RQT9516

Enjoying BD-LIVE or BONUSVIEW in BD-Video

[BD-V]

What is BONUSVIEW?

BONUSVIEW allows you to enjoy functions such as picture-in-picture or secondary audio etc., with BD-Video supporting BD-ROM Profile 1 version 1.1/ Final Standard Profile.

What is BD-Live?

In addition to the BONUSVIEW function, BD-Video supporting BD-ROM Profile 2 that has a network extension function allows you to enjoy more functions such as subtitles, exclusive images and online games by connecting this unit to the Internet. In order to use the Internet feature, you must have this unit connected to a broadband network (> 13).

≥These discs may not be on sale in certain regions. ≥The usable functions and the operating method may vary with each disc, please refer to the instructions on the disc and/or visit their website.

Playing secondary video (picture-in-picture) and secondary audio

Secondary video can be played from a disc compatible with the picture-in-picture function. For the playback method, refer to the instructions for the disc.

To turn on/off secondary video

Press [PIP].

Secondary video is played. ≥Press the button to turn it ON and OFF.

To turn on/off secondary audio

Set “Soundtrack” in “Secondary Video” to “On” or “Off”

(> 35, “Signal Type”).

≥Discs may not always be played back

according to the settings on this unit, as certain playback formats are prioritized on certain discs.

≥Only the primary video is played during

search/slow-motion or frame-by-frame.

≥When “BD-Video Secondary Audio” in

“Digital Audio Output” is set to “Off”, secondary audio will not be played. Please check that “BD-Video Secondary Audio” is set to “On” (> 38).

≥When the secondary video is turned off, the

secondary audio is not be played.

Secondary video

Primary video

NOTE

Enjoying BD-Live discs with Internet

Many BD-Live compatible discs require content to be downloaded onto an SD card (> 56, Local storage) in order to access the available BD-Live features.

≥An SD card with 1 GB or more of free space (SD Speed Class Rating 2 or higher) needs

to be inserted prior to inserting the BD-Live compatible disc.

Some BD-Live content available on the Blu-ray discs may require an Internet account to be created in order to access the BD-Live content. Follow the screen display or instruction manual of the disc for information on acquiring an account.

Preparation

≥Connect to the network. (> 13)

1 Insert an SD card (> 18).

≥If the SD card menu screen is displayed, press [BD/SD], select “BD/DVD”.

2 Insert the disc (> 18).

≥For operation method, refer to the instructions on the disc.

To use the above functions, it is recommended that you format the card on this unit. Format the card using the following procedures.

Formatting SD cards/Deleting data

It is impossible to restore data after formatting the card or erasing the data. Once a card is formatted, all data including those recorded on the PC is erased as well, even if the data were protected with other equipment.

Confirm whether the card can be formatted.

1) Insert an SD card (> 18).

2) Press [START].

3) Press [3, 4] to select “To Others” and press [OK].

4) Press [3, 4] to select “Card Management” and press [OK].

5) Press [3, 4] to select “BD-Video Data Erase” or “Format SD Card” and press [OK].

6) Press [2, 1] to select “Yes” and press [OK].

7) Press [2, 1] to select “Start” and press [OK].

≥While using this feature, do not remove the

SD card. Doing so will cause playback to stop.

≥A message may be displayed when SD

card doesn't have enough storage capacity for BD-Live content. Please make space available on the current SD card, or insert another SD card.

≥For details about usable cards, refer to

“Media (Disc, card and USB device) information” (> 44)

≥The unit must be connected to the Internet

and set up (> 33) to use the BD-Live functions. “BD-Live Internet Access” may need to be changed for certain discs (> 37).

≥When discs supporting BD-Live are played

back, the player or disc IDs may be sent to the content provider via the Internet. You can restrict Internet access (> 37, “BD-Live Internet Access” ).

≥The unit is connected to the Internet when

BD-Live functions are used, generating communication charges.

≥The playback may be paused depending on

the communication environment. Some functions may be disabled to prevent skipping to sections that have not been downloaded, etc.

Card Management No. of Files 6

Free space 300 MB

SD CARD

Format this SD Card.

OK RETURN

BD-Video Data Erase

Format SD Card

NOTE

Playback

RQT9516

Playing DivX® videos

[DivX]

ABOUT DIVX VIDEO-ON-DEMAND:

This DivX

Certified device must be registered in order to play DivX Video-on-Demand (VOD) content. First generate the DivX VOD registration code for your device and submit it during the registration process. [Important: DivX VOD content is protected by a DivX DRM (Digital Rights Management) system that restricts playback to registered DivX Certified devices. If you try to play DivX VOD content not authorized for your device, the message “

Authorisation Error.

” will be displayed and your content will not play.]

Learn more at www.divx.com/vod.

Display the unit’s registration code.

(> 40, “DivX Registration” in “General”)

≥After playing DivX VOD content for the first time, another registration

code is then displayed in “DivX Registration”. Do not use this registration code to purchase DivX VOD content. If you use this code to purchase DivX VOD content, and then play the content on this unit, you will no longer be able to play any content that you purchased using the previous code.

≥

If you purchase

DivX VOD

content using a registration code different from this unit’s code, you will not be able to play this content. (“Authorisation Error.” is displayed.)

Regarding DivX VOD content that can only be played a set number of times

Some DivX VOD content can only be played a set number of times. When you play this content, the remaining number of plays is displayed. You cannot play this content when the number of remaining plays is zero. (“Rental Expired.” is displayed.)

When playing this content

≥The number of remaining plays is reduced by one if

– you play the content to the end. – you press [Í]. – you press [∫STOP] and play others. – you press [∫STOP] twice. (except for content of USB device) – you press [< OPEN/CLOSE] or remove the USB device.

You can display subtitles text onto the DivX video disc on this unit. This function has no relation to the subtitles specified in DivX standard specifications and has no clear standard. The operation might be different or it may not operate properly depending on the way the file was made or the state of this unit (playing, stopped, etc.).

1 While playing, press [DISPLAY]. 2 Press [3, 4] to select “Disc” and press [1]. 3 Press [3, 4] to select “Subtitle” and press [1]. 4 Press [3, 4] to select “On” and press [1]. 5 Press [3, 4] to select “Text”.

≥DivX video files that do not display “Text” do not contain subtitles

text. Subtitles text cannot be displayed.

≥If the subtitles text are not displayed correctly, try changing the

language settings. (> 37)

To exit the screen

Press [DISPLAY].

ABOUT DIVX VIDEO:

DivX

is a digital video format created by DivX, Inc. This is an official DivX Certified device that plays DivX video. You can play DVD-R/R DL, CD-R/RW discs and USB device which contain DivX video contents that have been recorded on a personal computer. (About structure of folders

D 47, “Structure of folders that can play back on this unit”)

≥Because DivX format can use many different codecs, there is no guarantee that all DivX files will play. (> 46, “About MP3/JPEG/

DivX files”)

1 Insert a disc or a USB device. (> 18)

≥If the disc containing data in different file

formats is inserted, the file selection menu may be displayed. Press [3, 4] to select “Play Video (DivX)” and press [OK].

2 Press [3, 4] to select the title

and press [OK].

Play starts on the selected title.

≥The picture sizes set for recording

may prevent the unit from showing pictures in the proper aspect. You may be able to adjust the aspect through the TV.

≥Successive play is not possible.

≥You can use search and skip

functions. (> 19)

≥Press [SKIP:, SKIP9] to

show other pages.

DVD-R/R DL, CD-R/RW, USB device To switch from other menus to DivX menu

(If the media contains data in different file formats)

1) Press [START].

2) Press [3, 4] to select “Menu” and press [OK].

3) Press [3, 4] to select “Play Video (DivX)” and press [OK].

e.g., Display

Play Pictures (JPEG)

Select an action or press RETURN.

Play Music (MP3)

Play Video (DivX)

OK RETURN

OPTION

e.g.,

CD (DivX)

Play

RETURN

OPTION

DIRECT NAVIGATOR

No.

Name of Title

Folders can be selected from OPTION.

Page 01/01

001 ABC.divx

DivX

e.g.,

NOTE

TIPS

Playing a title in another folder

1 While the “DIRECT NAVIGATOR” is displayed

Press [OPTION], press [3, 4] to select “Folder” and press [OK].

2 Press [3, 4] to select a folder and press [OK].

The “DIRECT NAVIGATOR” for the folder appears.

≥You cannot select folders that

contain no compatible files.

To return to the previous screen

Press [RETURN].

Selected folder No. /Total folders

If the folder has no title, “– –” is displayed as folder number.

CD (DivX)

DIRECT NAVIGATOR

Folder selection

Page 01/01

F 1/21

RETURN

Image001

Image002 Image003 Image004 Image005 Image006 Image007 Image008 Image009 Image010

12_02_2004

e.g.,

NOTE

TIPS

Regarding DivX VOD content

DivX Registration

DivX® Video On Demand

Your registration code is : XXXXXXXX

To learn more visit www.divx.com/vod

8 alphanumeric characters

Displaying subtitles text

Playback

RQT9516

Playing still pictures

[JPEG]

Playback of the BD-RE, DVD-RAM/R/R DL or CD-R/RW with still pictures recorded. This unit can also play still pictures recorded on the SD card or USB memory. In addition, you can also connect Panasonic digital camera by USB connection. (About structure of folders

D 47, “Structure of folders that can play back on this unit”)

Connecting a USB device

≥Setup screen may be displayed on

equipment connected with the USB. Set it to the mode for connecting to a PC.

≥Also read the operating instructions of the

connected equipment for details of connection and setup.

≥Do not disconnect the USB connection

cable while recognizing.

TUNE

SETUP MIC

SD CARD

TUNE

SETUP MIC

SD CARD

Connect to USB terminal

Panasonic digital camera, etc.

USB connection cable

Specified cable such as accessory of the USB equipment

NOTE

1 Insert a disc, SD card or USB device. (> 18)

BD-RE, DVD-RAM

“Album View” screen is displayed ≥When the “Title View” screen is displayed, press the [G] button to switch to the

“Album View” screen.

≥If the DVD-RAM containing both JPEG and AVCHD format is inserted, the file

selection menu may be displayed.

DVD-R/R DL, CD-R/RW, SD card, USB device

≥If the media containing data in different file formats is

inserted, the file selection menu may be displayed.

Press [3, 4] to select “Play Pictures (JPEG)” and press [OK].

“Picture View” screen is displayed

B Go to step 3

2 Press [3, 4, 2, 1] to select the album and press [OK].

3 Press [3, 4, 2, 1] to select the still picture and press [OK].

≥Press [2, 1] to display the previous or

next still picture.

≥Press [SKIP:, SKIP9] to show other

pages.

To return to the previous screen

Press [RETURN].

To exit the screen

Press [TOP MENU/DIRECT NAVIGATOR].

DVD-RAM/R/R DL, CD-R/RW, SD card, USB device To switch from other menus to JPEG menu

(If the media contains data in different file formats)

1) Press [START].

2) Press [3, 4] to select “Menu” and press [OK].

3) Press [3, 4] to select “Play Pictures (JPEG)” and press [OK].

≥Small-sized still pictures are displayed with

a frame.

e.g., Display

SD CARD

Play Video (AVCHD)

Select an action or press RETURN.

Play Pictures (JPEG)

OK RETURN

OPTION

Play Video (MPEG-2)

e.g., [SD]

R G

 

DIRECT NAVIGATOR

Album View

DVD-RAM(VR)

Video

Picture

Press OK to go to Picture View

Previous Next Slide Show

RETURN

Video Picture

Page 02/02

Total 8

106_DVD

Total 13

12/9/2006

OPTION

e.g.,

TIPS

NOTE

Playback

RQT9516

Playing still pictures

Useful functions during still picture play

Start Slide Show

You can display still pictures one by one at a constant interval.

BD-RE, DVD-RAM

1 While the “Album View” screen is displayed

Press [3, 4, 2, 1] to select the album and press [OPTION].

2 Press [3, 4] to select “Start Slide Show” and press [OK]. ≥You can also start slideshow by pressing [1PLAY] after selecting

the album.

DVD-R/R DL, CD-R/RW, SD card, USB device

1 While the “Picture View” screen is displayed

Press [OPTION].

2 Press [3, 4] to select “Start Slide Show” and press [OK].

To stop slideshow

Press [∫STOP].

Slide Show Setting

After performing step 1 in Start Slide Show above, 2 Press [3, 4] to select “Slide Show Setting” and press [OK].

3 To change the display interval

Press [3, 4] to select “Display interval” and press [2, 1] to select the interval (“Long”, “Normal” or “Short”). ≥When a still picture with large number of pixels is played, the

display interval may become longer. Even if the setting is changed, the display interval may not become shorter.

To set display method

Press [3, 4] to select “Transition Effect” and press [2, 1] to select “Fade”, “Motion” or “Random”. “Fade”: Pictures are changed by fading out and fading in.

This setting is factory preset.

“Motion”: Pictures are changed by fading out and fading in,

while it is enlarged, reduced, or moved up or down.

“Random”: In addition to the “Motion”, pictures are changed by

various methods.

To repeat Slide Show

Press [3, 4] to select “Repeat Play” and press [2, 1] to select “On” or “Off”.

To listen to a Background Music

Music files on an iPod, a USB device or a music CD can be played back as Background music during the slideshow. Press [3, 4] to select “

Soundtrack

” and press [2, 1] to select

“On” or “Off”.

≥You cannot search or skip on a music. ≥When the slideshow stops, the playback of the music also

stops.

≥Playback of the music files will be in the following order:

[CD] : Order of “Music list” display in repeat mode. iPod: The music files will be played back in repeat mode.

≥When a music CD, a USB device with MP3 recorded and an

iPod is inserted/connected to this unit, the iPod has first priority to be played back as Background. To playback MP3 recorded on a USB device as Background music, remove the iPod and music CD from the main unit.

To select a folder

A folder to playback can be selected when a USB device with MP3 recorded is connected to this unit. Press [3, 4] to select “Soundtrack Folder” and press [OK], and press [2, 1] to select folder and press [OK].

4 Press [3, 4, 2, 1] to select “Set” and press [OK].

Rotate

1 While playing (except for slideshows)

Press [OPTION].

2 Press [3, 4] to select “Rotate RIGHT” or “Rotate LEFT” and

press [OK].

≥The rotation information will be stored until the unit is turned off or

the media is removed.

Zoom out

This function is only available for small-sized still pictures. 1 While playing (except for slideshows)

Press [OPTION].

2 Press [3, 4] to select “Zoom out” and press [OK]. ≥To cancel “Zoom out”, press [3, 4] to select “Zoom in” in step 2

and press [OK].

≥The zoom-out information will not be stored.

To select the still pictures in another folder

BD-RE, DVD-RAM

To switch to another higher folder

(Only if there is a multiple number of higher folders recognizable) 1 While the “Album View” screen is displayed

Press [OPTION].

2 Press [3, 4] to select “Select Folder” and press [OK].

3 Press [2, 1] to select the higher folder and press [OK].

DVD-R/R DL, CD-R/RW

1 While the “Picture View” screen is displayed

Press [OPTION].

2 Press [3, 4] to select “Folder” and press [OK].

3 Press [3, 4] to select a folder and press [OK].

The “Picture View” screen for the folder appears.

To show the picture properties

While playing Press [STATUS] twice.

To exit, press [STATUS].

\JPEG\DCIM001

RETURN

Select Folder

Change the Album folder to be accessed.

Press [OK] to set

DIRECT NAVIGATOR

Folder selection

CD(JPEG)

001 002 003 004 005 006 007

008 009 010

103 104 105

021216_0026

F 2/25

RETURN

e.g.,

Date 11.12.2009 Total 3/9

Shooting date

e.g., JPEG on DVD-RAM

Playback

RQT9516

Playing music

[CD] [MP3]

You can play generally available music CD or MP3 files recorded onto a DVD-R/R DL, CD-R/RW and USB device. (About structure of folders

D 47, “Structure of folders that can play back on this unit”)

1 Insert a disc or USB device. (> 18)

≥If the media containing data in

different file formats is inserted, the file selection menu may be displayed. Press [3, 4] to select “Play Music (MP3)” and press [OK].

2 Press [3, 4] to select the track and press [OK].

Play starts on the selected track.

To switch from other menus to MP3 menu

(If the media contains data in different file formats)

1) Press [START].

2) Press [3, 4] to select “Menu” and press [OK].

3) Press [3, 4] to select “Play Music (MP3)” and press [OK].

≥You can use search and skip functions.

(> 19)

≥When the “Screen Saver Function” is set to

“On” (> 38), the screen switches to Screen Saver mode if there is no operation for 5 minutes after starting playback. (Playback continues.)

e.g. Display

Play Pictures (JPEG)

Select an action or press [RETURN].

Play Music (MP3)

Play Video (DivX)

OK RETURN

OPTION

e.g.

0.09 4.30

01 02 03 04 05

DIRECT NAVIGATOR

Music list

No.

Track Name Play Time

Track1

4min30sec 3min41sec 4min30sec 3min11sec 5min 2sec

Track2

5 Tracks / Total Play Time 20min54sec

Track3 Track4 Track5

Play

RETURN

“ ” indicates the track currently

playing.

e.g. [CD]

TIPS

[MP3] Playing a track in another folder

1 While the “Music list” is displayed

Press [OPTION], press [3, 4] to select “Select Folder” and press [OK].

2 Press [3, 4] to select a folder and press

[OK]. The “Music list” for the folder appears.

≥You cannot select folders that contain no

compatible tracks.

To return to the previous screen

Press [RETURN].

Playing music continuously even after turning off power to the television

When the unit is connected to a Panasonic TV (VIERA) that supports HDAVI Control 2 or later and other device supports VIERA Link, the unit is turned off if the power to the television is turned off, since “Power off link” (> 29) operates. The following operations make it possible to keep the power of the unit ON and to play music continuously.

Set “Power Off Link” to “Video” (> 39).

≥Sound may be discontinued for several

seconds when the power to the television is turned off.

DIRECT NAVIGATOR

Select Folder

CD(MP3)

001 My favorite 002 Brazilian pops 003 Chinese pops 004 Czech pops 005 Hungarian pops 006 Liner notes 007 Japanese pops

008 Mexican pops 009 Philippine pops 010 Swedish pops 011 Momoko 012 Standard number 013 Piano solo 014Vocal

MP3 music

F 8/25

OK RETURN

Selected folder No. /Total folders

If the folder has no track, “– –” is displayed as folder number.

e.g.

NOTE

TIPS

NOTE

Playback

RQT9516

Listening to the Radio

Up to 30 stations can be set.

1 Press [RADIO] to select “FM”.

This unit: Press [SELECTOR].

2 Press [STATUS] to select the position to start the

auto preset search.

Each time you press the button:

LOWEST (factory preset):

To begin auto preset with the lowest frequency (FM 87.50).

CURRENT:

To begin auto preset with the current frequency.* * To change the frequency, refer “Manual tuning” (B right).

3 Press and hold [OK].

Release the button when “AUTO” is displayed.

The tuner starts to preset all the stations it can receive into the channels in ascending order.

≥“SET OK” is displayed when the stations are set, and the radio tunes

to the last preset station.

≥“ERROR” is displayed when automatic presetting is unsuccessful.

Preset the stations manually (B right).

1 Press [RADIO] to select “FM”. 2

Press the numbered buttons to select the channel.

To select a 1-digit number e.g., 1: [1] > [OK]. To select a 2-digit number e.g., 12: [1] B [2] Alternatively, press [W, X] or [2, 1].

When a stereo FM broadcast is being received, “ST” lights in the display.

≥The FM setting is also shown on the TV display.

∫ If noise is excessive

When FM is selected Press [AUDIO] to display “MONO”.

Press the button again to cancel the mode.

≥The mode is also cancelled when you

change the frequency.

≥This setting can be preset for each broadcasting station. When

“MONO” appears follow procedures 1 and 2 in “Presetting stations manually” (> below).

1 Press [RADIO] to select “FM”. 2 Press [SEARCH6] or [SEARCH5] to select

the frequency.

≥Main unit:

Press [X TUNE W] to select the frequency.

≥When a radio broadcast is being

received, “T” lights in the display.

≥To start automatic tuning, press

and hold [SEARCH6, SEARCH5] (main unit: [X TUNE W]) until the frequency starts scrolling. Tuning stops when a station is found.

∫ Presetting stations manually

Up to 30 stations can be set. 1 While listening to the radio broadcast

Press [OK].

2 While “P” is flashing on the display

Press the numbered buttons to select a channel.

To select a 1-digit number e.g., 1: [1] > [OK]. To select a 2-digit number e.g., 12: [1] B [2]

A station previously stored is overwritten when another station is stored in the same channel preset.

The unit can display the text data transmitted by the radio data system (RDS) available in some areas. If the station you are listening to is transmitting RDS signals, “RDS” will light up on the display.

While listening to the radio broadcast

Press [DISPLAY] to display the text data.

Each time you press the button:

PS: Program service PTY: Program type OFF: Frequency display

* M.O.R. M”=Middle of the road music

Setting up the radio

Presetting stations automatically

EXT-IN

RADIO

STATUS

AUDIO

SEARCH SEARCH

123

7809

DISPLAY

abc

def

jkl

mno

tuv

ghi

qrs

xyz

SEARCH SEARCH

Numbered

buttons

RADIO

AUDIO DISPLAY

STATUS

, OK

TUNE

SELECTORSETUP MIC

SD CARD

TUNE

SELECTOR

TUNE

Listening/confirming the preset channels

Manual tuning

RDS broadcasting

PTY displays

NEWS VARIED FINANCE COUNTRY

AFFAIRS POP M CHILDREN NATIONAL

INFO ROCK M SOCIAL A OLDIES

SPORT M.O.R. M* RELIGION FOLK M

EDUCATE LIGHT M PHONE IN DOCUMENT

DRAMA CLASSICS TRAVEL TEST CULTURE OTHER M LEISURE ALARM SCIENCE WEATHER JAZZ

RDS displays may not be available if reception is poor.

MONO

NOTE

Radio

RQT9516

Enjoying TV, etc. with this unit’s speakers

You can enjoy TV broadcasts with this unit’s speakers.

Preparation

Confirm the audio connection to the OPTICAL IN or AUX terminal on this unit (> 10 to 12). Turn on the TV.

1 Press [EXT-IN] several times to select

“

D-IN 1”

(DIGITAL IN 1)*1,

“

D-IN 2” (DIGITAL IN 2)*2 or

“AUX”*1.

This unit: Press [SELECTOR].

≥D-IN 1 (DIGITAL IN 1)

When connecting using OPTICAL 1(TV) terminal.

≥D-IN 2 (DIGITAL IN 2)

When connecting using OPTICAL 2(STB) terminal.

≥AUX

When connecting using AUX terminal.

For connections with the TV. (> 10, 11)

*2For connections with other devices. (> 12) ≥When the system is connected to an HDAVI Control 2 or

later-compatible TV via an HDMI cable, TV broadcast audio is output through the system speakers if the TV input is switched to TV tuner mode. See “Setting the TV audio for VIERA Link “HDAVI Control”” on page 28 for setting method.

≥Reduce the volume on the TV to its minimum, and then adjust the

volume of this unit.

You can enhance stereo sources with surround sound effect.

Press [SURROUND] several times to select the mode.

≥You can also press [SURROUND] and then [3, 4] to select the

mode.

≥The selected effect will only be displayed on the main unit. While “MANUAL” is displayed

Press [

2, 1] and select the desired effect.

For more detailed information on this operation, please refer to the “Enjoying surround sound effects” section on page 17.

You can adjust the mode depending on the source or situation.

1 Press [SOUND] several times to select the mode.

≥You can also press [SOUND] and then [3, 4] to select the

mode.

≥The selected effect will only be displayed on the main unit.

2 While the selected mode is displayed

Press [2, 1] and select the desired setting.

For more detailed information on this operation, please refer to the “Changing the sound modes” section on page 17.

Select to suit the type of audio from the OPTICAL IN terminals on the main unit. ≥Underlined items are the factory presets.

1 Press [EXT-IN] several times to select “D-IN 1”

(DIGITAL IN 1) or “D-IN 2” (DIGITAL IN 2).

Main unit: Press [SELECTOR].

2 Press [STATUS] several times to select the

mode.

≥You can also press [STATUS] and then [3, 4] to select the

mode.

≥The digital audio input settings are to be set separately to each

source, “D-IN 1” and “D-IN 2”.

≥The selected effect will only be displayed on the main unit.

3 While the selected mode is displayed

Press [2, 1] and select the desired setting.

*3When “D-IN 1” is selected. *4 When “D-IN 2” is selected. *5The device connected to the OPTICAL 2(STB) terminal must be

connected to the TV via an HDMI cable. If it is not connected via an HDMI cable, “NOT CONDITIONAL” is displayed on the main unit.

Enjoying TV and other devices sound from this unit’s speakers

Recommended modes to enjoy TV audio:

≥DOLBY PL II MOVIE ≥DOLBY PL II MUSIC ≥S.SURROUND

EXT-IN

SOUND

SURROUND

STATUS

EXT-IN

STATUS

SURROUND

SOUND

TUNE

SELECTORSETUP MIC

SD CARD

SELECTOR

Adjusting the sound

Making settings for digital audio input

Available settings

Mode Setting

DUAL: (Only works with Dolby Dual Mono)

– M1 – M2 – M1+M2

(stereo audio)

≥If this is set to “M1” or to “M2”, the “PCM FIX” will

automatically be set to “OFF”(> below).

DRC: (Dynamic Range Compression)

–ON

Adjust for clarity even when the volume is low by compressing the range of the lowest sound level and the highest sound level. Convenient for late night viewing. (Only works with Dolby Digital)

–OFF

The full dynamic range of the signal is reproduced.

PCM FIX: – ON

Select when receiving only PCM signals.

–OFF

Select when receiving Dolby Digital and PCM signals.

≥When receiving true 5.1-channel surround sound,

select “OFF”.

TV AUDIO

– AUX

Select when receiving analogue sound from the TV to the AUX terminal.

–D-IN 1

Select when receiving digital sound from the TV to the OPTICAL 1(TV) terminal.

CABLE/SAT AUDIO

4,5

–SET

Select when setting the main unit to switch to “D-IN 2” when the input channel of a HDMI connected STB is selected on the TV (B 28, Setting the TV audio for VIERA Link “HDAVI Control”).

–OFF

Select to cancel this setting.

≥Audio that is input through the OPTICAL DIGITAL IN or

AUX terminals are not output from the HDMI terminal.

NOTE

RQT9516

Linked operations with the TV

(VIERA Link “HDAVI ControlTM”)

When switching between this unit’s speakers and TV speakers, the TV screen may be blank for several seconds.

What is VIERA Link “HDAVI Control”?

VIERA Link “HDAVI Control” is a convenient function that offers linked operations of this unit, and a Panasonic TV (VIERA) under “HDAVI Control”. You can use this function by connecting the equipment with an HDMI cable. See the operating instructions for connected equipment for operational details.

Preparation

1 Connect this unit to your TV with an HDMI cable (> 11). 2 Set “VIERA Link” to “On” (> 39).

(The default setting is “On”.)

3 Set the “HDAVI Control” operations on the connected equipment (e.g., TV). 4 Turn on all “HDAVI Control” compatible equipment and select this unit’s input

channel on the connected TV so that the “HDAVI Control” function works properly.

Also when the connection or settings are changed, repeat this procedure.

≥VIERA Link “HDAVI Control”, based on the

control functions provided by HDMI which is an industry standard known as HDMI CEC (Consumer Electronics Control), is a unique function that we have developed and added. As such, its operation with other manufacturers’ equipment that supports HDMI CEC cannot be guaranteed.

≥This unit supports “HDAVI Control 4”

function.

“HDAVI Control 4” is the newest standard (current as of December, 2008) for Panasonic’s HDAVI Control compatible equipment. This standard is compatible with Panasonic’s conventional HDAVI equipment.

≥Please refer to individual manuals for other

manufacturers’ equipment supporting VIERA Link function.

≥It is recommended that you use

Panasonic’s HDMI cable. Recommended part number:

RP-CDHG10 (1.0 m), RP-CDHG15 (1.5 m), RP-CDHG20 (2.0 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m), etc.

≥Non-HDMI-compliant cables cannot be

utilized.

Setting the TV audio for VIERA Link “HDAVI Control”

You can set the main unit to link audio operations with the TV.

∫ Setting the audio from the TV

Preparation ≥Select between “AUX” and “D-IN 1” (DIGITAL IN 1) to work with the linked

operations for the TV audio. – Confirm the audio connection to the AUX(TV) terminal (for “AUX”) or OPTICAL

1(TV) terminal (for “D-IN 1”) (> 11) .

With the remote control of the main unit;

1 Press [EXT-IN] to select “AUX” or “D-IN 1” (DIGITAL IN 1). 2 Press [STATUS]. 3 Press [3, 4] to select “TV AUDIO”. 4 Press [2, 1] to switch “AUX” or “D-IN 1” (DIGITAL IN 1) and press [OK].

Whenever the connection or settings are changed, reconfirm the points above.

∫ Setting the audio from the STB

This unit can be set to link operations with the TV so as to output audio from the connected STB, etc. when the TV input is set to the input channel designated for the STB, etc. Preparation

≥Select the STB input channel on the TV. ≥Confirm the audio connection to the OPTICAL 2(STB) terminal (for “D-IN 2”)

(> 12).

With the remote control of this unit;

1 Press [EXT-IN] to select “D-IN 2” (DIGITAL IN 2). 2 Press [STATUS]. 3 Press [3, 4] to select “CABLE/SAT AUDIO”. 4 Press [2, 1] to select

“SET” and press [OK].

≥If the input channel of the STB on the TV is changed or if you want to change

the device allocated for the linked operations, select

“OFF” in step 4 above and

then repeat steps 1 to 4.

≥The connected STB must also be connected

to the TV via an HDMI cable.

Refer to the operating instructions of the respective device for details.

≥It is also possible to connect an HDMI and

optical output compatible Panasonic DVD, Blu-ray recorder in the place of the STB.

What you can do with “HDAVI Control”

Speaker Selection

You can select whether audio is output from the unit’s speakers or the TV speakers by using the TV menu settings. For details, refer to the operating instructions of your TV.

Home Cinema

This unit’s speakers are active. ≥When this unit is in standby mode, changing the TV speakers to this unit’s speakers in the TV menu will automatically turn the unit on and

select “AUX”*

, “D-IN 1” (DIGITAL IN 1)*1 or “D-IN 2” (DIGITAL IN 2)*2 as the source.

≥The TV speakers are automatically muted. ≥You can control the volume setting using the volume or mute button on the TV’s remote control. (The volume level is displayed on the main

unit’s FL display.)

≥To cancel muting, you can also use the home theater remote control (> 18). ≥If you turn off this unit, TV speakers will be automatically activated.

TV speakers are active. ≥The volume of this unit is set to “0”.

– This function works when “BD/DVD”, “SD”, “USB”, “AUX”*

, “D-IN 1” (DIGITAL IN 1)*1 or “D-IN 2” (DIGITAL IN 2)*2 is selected as the source

on the home theater system.

≥Audio output is 2-channel audio.

NOTE

TIPS

≥When “TV” is selected in “Speaker Selection”, the audio from an iPod will not be output from the TV’s speakers during slideshow

background music playback. (> 24)

NOTE

RQT9516

If you connect this unit to a TV that has “HDAVI Control 2” or later with an HDMI cable, you can operate this unit using buttons on the TV remote control. The buttons that you can use for this unit vary depending on the TV. For details, refer to the operating instructions of the TV. Use the remote control supplied with this unit if you cannot operate this unit using buttons on the TV remote control. ≥The operation of this unit may be interrupted when you press

incompatible buttons on the TV remote control.

∫ Using the Control Panel

You can operate the playback with the indicated controls.

∫ When you want to leave the TV on and set only this unit to standby mode

Press [Í] on this unit’s remote control and set to standby mode.

∫ When not using “HDAVI Control”

Set “VIERA Link” in the Setup menu to “Off”. (> 39)

Automatic input switching

When the following operations are performed, the television will automatically switch the input channel and display the corresponding action. – When play starts on the unit – When an action that uses the display screen is performed

(e.g., Direct Navigator screen)

≥[BD-V] [DVD-V] When playback stops, the TV will automatically

return to TV tuner mode.

≥When you switch the TV input to TV tuner mode, this unit will

automatically switch to “AUX”

, “D-IN 1” (DIGITAL IN 1)*1 or “D-IN

2” (DIGITAL IN 2)

≥This function does not work when the iPod selector (SIMPLE

mode) or iPod Video menu (EXTENDED mode) is chosen. (> 31)

≥When [1PLAY] is pressed, the playback image is not

immediately displayed on the screen and it may not be possible to watch the contents from where playback started. In this case, press [SKIP:] or [SEARCH6] to go back to where playback started.

Automatic lip-sync function (for HDAVI Control 3 or later)

Delay between audio and video is automatically adjusted, enabling you to enjoy smooth audio for the picture (> 39, Time Delay). ≥This function works only when “BD/DVD”, “SD”, “USB”, “AUX”

“D-IN 1” (DIGITAL IN 1)

or “D-IN 2” (DIGITAL IN 2)*2 is selected as

the source on this unit.

Power off link

All connected equipment compatible with “HDAVI Control”, including this unit, automatically turns off when you switch the television off. ≥This unit automatically turns off even during playback or any other

operation.

To continue audio playback even when the TV is turned off, select “Video” in “Power Off Link” (> 39).

∫ Intelligent Auto Standby

Intelligent Auto Standby responsibly manages your power consumption. This function is available with the TV that supports “HDAVI Control 4”.

≥If connected with a TV (VIERA) with the “Intelligent Auto Standby”

setting activated on the TV, when switching the TV input, the unit will be automatically turned to standby. For details please read the operating instructions of the TV. – When “Speaker Selection” is set to “Home Cinema”, the main unit

will not automatically turn to standby.

One touch play

You can turn on this unit and the TV, and start play with a single press of a button. While the unit and the TV are in standby mode;

Press [1PLAY].

≥This unit’s speakers will automatically be activated. (> 28)

≥When [1PLAY] is pressed, the playback image is not

immediately displayed on the screen and it may not be possible to watch the contents from where playback started. In this case, press [SKIP:] or [SEARCH6] to go back to where playback started.

*1 “AUX” or “D-IN 1” works depending on the “TV AUDIO” setting

(B 28, Setting the TV audio for VIERA Link “HDAVI Control”).

*2 “D-IN 2” works depending on the “CABLE/SAT AUDIO” setting

(B 28, Setting the TV audio for VIERA Link “HDAVI Control”).

NOTE

Easy control only with VIERA remote control

Using the START menu to operate this unit

By using the TV remote control, you can play media using the START menu.

1 Press the button for VIERA Link

on the TV remote control.

2 Select the home theater.

≥The START menu is displayed

3 Select the desired items on the

START menu (

> 15).

Using the option menu to operate this unit

By using the TV remote control, you can play discs using the “Control Panel” and display the Top Menu (for BD-Video and DVD-Video) or Pop-up Menu (for BD-Video).

≥This works only during “BD/DVD” or “SD” playback and resume

modes.

1 Press [OPTION].

≥You cannot use the option menu while the

Top Menu for BD-Video or DVD-Video is displayed.

≥This can also be displayed by using the

VIERA menu screen.

2 Select an item, then press [OK].

Control Panel Control Panel is displayed. Follow

the indications on the screen (> below).

Screen Aspect (> 20) Top M enu [BD-V] [AVCHD] [DVD-V] Top menu is displayed. Menu [DVD-V] Menu is displayed. Pop-up Menu [BD-V] Pop-up menu is displayed. Rotate RIGHT [JPEG] Rotate the still picture. Rotate LEFT [JPEG] Zoom in [JPEG] Enlarge or shrink the still picture. Zoom out [JPEG]

≥Depending on the menu, some button operations cannot

be performed from the TV’s remote control.

≥You cannot input numbers with the numbered buttons on

the TV’s remote control ([0] to [9]). Use this unit’s remote control to select the playlist etc.

e.g., [BD-V]

RETURN

To Others

Playback Di sc

Top Menu

Home Cinema

START

BD-Video

Input Selection

Sound(Equalizer)

Network

RETURN

OPTION

Control Panel

Screen Aspect

Top Menu

Pop-up Menu

e.g., [BD-V]

e.g.,

NOTE

RQT9516

Using the iPod

You can enjoy iPod music through this unit’s speakers or view iPod videos/photos on the TV.

Preparation

≥To view photos/videos from the iPod

– Ensure the video connection to the VIDEO OUT terminal on this unit (> 10). – Operate the iPod menu to make the appropriate photo/video output settings for your TV. (Refer to operating instructions of your iPod.)

≥To display the picture, turn on the TV and select the appropriate video input mode. ≥Before connecting/disconnecting the iPod, turn the main unit off or reduce the volume of the main unit to its minimum.

While an iPod is connected

≥Do not push the Dock for iPod. ≥Do not push or pull your iPod back and forth with great force.

Compatible iPod

iPod Connection

1 Open the Dock for iPod.

≥Hold the dock when connecting/disconnecting the iPod.

About dock adapter

≥Attach the dock adapter which should be

supplied with your iPod to the dock for the stable use of the iPod. If you need an adapter, consult your iPod dealer.

About recharging the battery

≥iPod will start recharging regardless of whether

this unit is on or off.

≥“IPOD ¢” will be shown on the main unit’s

display during iPod charging in main unit standby mode.

≥Check iPod to see if the battery is fully

recharged.

≥If you are not using iPod for an extended period

of time after recharging has completed, disconnect it from main unit, as the battery will be depleted naturally. (Once fully recharged, additional recharging will not occur.)

2 Connect the iPod (not included) firmly.

Recharging starts when the iPod is inserted.

Main unit

iPod

Pull out

Main unit

Dock for iPod

Dock adapter (not included)

NOTE

DO NOT

Name Memory size ≥Compatibility depends on the software

version of your iPod.

≥Audio/video cannot be recorded or

transmitted to iPods via this system.

≥Panasonic makes no warranty for iPod data

management.

≥For more information, refer to the

operating instructions for iPod.

≥The contents of the operating instructions

and those displayed on iPod may differ partially, but this will not fundamentally affect use of playback.

∫ To use the iPod touch features

1 Press the Home button on the iPod touch. 2 Select the iPod touch features on the touch

screen to operate.

iPod touch 2nd generation 8 GB, 16 GB, 32 GB iPod nano 4th generation (video) 8 GB, 16 GB iPod classic 120 GB iPod touch 1st generation 8 GB, 16 GB, 32 GB iPod nano 3rd generation (video) 4 GB, 8 GB iPod classic 80 GB, 160 GB iPod nano 2nd generation (aluminum) 2 GB, 4 GB, 8 GB iPod 5th generation (video) 60 GB, 80 GB iPod 5th generation (video) 30 GB iPod nano 1st generation 1 GB, 2 GB, 4 GB iPod 4th generation (colour display) 40 GB, 60 GB iPod 4th generation (colour display) 20 GB, 30 GB iPod 4th generation 40 GB iPod 4th generation 20 GB iPod mini 4GB, 6GB

NOTE

TIPS

Other devices

+ 90 hidden pages

Panasonic SA-BT205, SB-HF770, SB-HC300, SB-HS870, SB-HW200 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual