Panasonic SAPT-350-E, SAPT-350-EB, SAPT-350-EG Service manual

ORDER NO. MD0704027CE

DVD Home Theater Sound System

SA-PT350E SA-PT350EB SA-PT350EG

Colour

(S).......................Silver Type

Specifications

lGENERAL

Power Supply:

E/EG areas:

EB area:

Power Consumption: 90 W

Power Consumption in Standby Mode:

approx. 0.8 W

Dimensions (W×H×D): 430×64.7×364.4 mm

Mass: Main unit 3.5 kg

Operating Temperature Range: +5°C to +35°C

Operating Humidity Range: 5% to 90% RH (no

condensation)

lAMPLIFIER SECTION

RMS Output Power: Dolby Digital Mode

lTotal RMS Dolby Digital mode power:

500 W

At 1 kHz and total harmonic of 10%

lFront Ch: 85 W / Channel (4 Ω)

lCenter Ch: 85 W / Channel (4 Ω)

lSurround Ch*: 80 W / Channel (4 Ω)

At 100 Hz and total harmonic of 10%

lSubwoofer Ch: 85 W / Channel (4 Ω)

AC 230 V, 50 Hz

AC 230-240 V, 50 Hz

DIN Output Power: Dolby Digital Mode

lTotal DIN Dolby Digital mode power:

280 W

At 1 kHz and total harmonic of 1%

lFront Ch: 50 W / Channel (4 Ω )

lCenter Ch: 50 W / Channel (4 Ω )

lSurround Ch*: 40 W / Channel (4 Ω )

At 100 Hz and total harmonic of 1%

lSubwoofer Ch: 50 W / Channel (4 Ω )

* Power output of the wireless receiver amplifier SE-FX65.

lFM TUNER, TERMINALS SECTION

Preset Memory: FM 30 stations

Frequency Modulation (FM)

Frequency range: 87.50-108.00 MHz

(50-kHz step)

Sensitivity: 1.8 µV (IHF)

S/N 26 dB: 1.4 µV

Antenna terminals: 75 Ω (unbalanced)

Digital Audio Input:

Optical digital input: Optical terminal

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Phone Jack:

SA-PT350E / SA-PT350EB / SA-PT350EG

Terminal: Stereo, 3.5 mm jack

Front Music Port:

Sensitivity: 100 mV, 1.4 kΩ

Terminal: Stereo, 3.5 mm jack

USB Port:

USB standard: USB 2.0 full speed

Media file format support: MP3 (*.mp3)

WMA (*.wma)

JPEG (*.Jpg, *.JPEG)

MPEG4 (*.asf) (For E/EG only)

USB device file system:

USB Port power:

(FAT12) (FAT16) (FAT32)

Max. 500 mA

lDISC SECTION (E/EG areas)

Discs played (8 cm or 12 cm):

(1) DVD [DVD-Video, DivX (*6, *7)]

(2) DVD-RAM [DVD-VR, MP3 (*2, *7), JPEG (*4, *7), MPEG4

(*5, *7), DivX (*6, *7)]

(3) DVD-R [DVD-Video, DVD-VR, MP3 (*2, *7), JPEG (*4, *7),

MPEG4 (*5, *7), DivX (*6, *7)]

(4) DVD-R DL [DVD-Video, DVD-VR]

(5) DVD-RW [DVD-Video, DVD-VR, MP3 (*2, *7), JPEG (*4, *7),

MPEG4 (*5, *7), DivX (*6, *7)]

(6) +R/+RW [Video]

(7) +R DL [Video]

(8) CD, CD-R/RW [CD-DA, Video CD, SVCD (*1), MP3 (*2, *7),

WMA (*3, *7), JPEG (*4, *7), MPEG4 (*5, *7), DivX (*6, *7), HighMAT Level 2 (Audio and Image)]

*1 Conforming to IEC62107

*2 MPEG-1 Layer 3, MPEG-2 Layer 3

*3 Windows Media Audio Ver.9.0 L3

lNot compatible with Multiple Bit Rate (MBR)

*4 Exif Ver 2.1 JPEG Baseline files

lPicture resolution: between 160 x 120 and 6144 x 4096 pixels (Sub sampling is 4:0:0, 4:2:0, 4:2:2, or 4:4:4). Extremely long and narrow pictures may not be displayed.

*5 MPEG4 data recorded with the Panasonic SD multi cameras

or DVD video recorders.

lConforming to SD VIDEO specifications (ASF standard)/ MPEG4 (Simple Profile) video system/G.726 audio system.

*6 Plays all versions of DivX® video (including DivX®6) with

standard playback of DivX® media files. Certified to the DivX Home Theater Profile.

*7 The total combined maximum number of recognizable audio,

picture and video contents and groups: 4000 audio, picture and video contents and 400 groups.

lDISC SECTION (EB area)

Discs played (8 cm or 12 cm):

(1) DVD [DVD-Video]

(2) DVD-RAM [DVD-VR, MP3 (*2, 5), JPEG (*4,5)]

(3) DVD-R [DVD-Video, DVD-VR, MP3 (*2, 5), JPEG (*4,5)]

(4) DVD-R DL [DVD-Video, DVD-VR]

(5) DVD-RW [DVD-Video, DVD-VR, MP3 (*2, 5), JPEG (*4, 5)]

(6) +R/+RW [Video]

(7) +R DL [Video]

(8) CD, CD-R/RW [CD-DA, Video CD, SVCD (*1), MP3 (*2, 5),

WMA (*3, 5), JPEG (*4, 5), HighMAT Level 2 (Audio and Image)]

*1 Conforming to IEC62107

*2 MPEG-1 Layer 3, MPEG-2 Layer 3

*3 Windows Media Audio Ver.9.0 L3

lNot compatible with Multiple Bit Rate (MBR)

*4 Exif Ver 2.1 JPEG Baseline files

lPicture resolution: between 160 x 120 and 6144 x 4096 pixels (Sub sampling is 4:0:0, 4:2:0, 4:2:2, or 4:4:4). Extremely long and narrow pictures may not be displayed.

*5 The total combined maximum number of recognizable audio

and picture contents and groups: 4000 audio and picture contents and 400 groups.

Pick Up:

Wavelength:

lCD: 785 nm

lDVD: 662 nm

Laser power:

lCD: CLASS 1M

lDVD: CLASS 1

Audio Output (Disc):

Number of channels: 5.1 ch (FL, FR, C, SL, SR,

SW)

lVIDEO SECTION

ideo System:

PAL 625/50, PAL 525/60, NTSC

Composite Video Output:

lOutput level: 1 Vp-p (75 Ω)

lTerminal: Scart jack (1 system)

S-video Output:

lY output level: 1 Vp-p (75 Ω)

lC output level: PAL; 0.3 Vp-p (75 Ω)

NTSC; 0.286 Vp-p (75 Ω)

lTerminal Scart jack (1 system)

Component Video Output: (NTSC: 480p/480i, PAL: 576p/576i)

lY output level: 1 Vp-p (75 Ω)

lPBoutput level: 0.7 Vp-p (75 Ω)

lPRoutput level: 0.7 Vp-p (75 Ω)

lTerminal: Pin jack (Y: green, PB: blue,

: red) (1 system)

RGB Video Output:

lR output level: 0.7 Vp-p (75 Ω)

lG output level: 0.7 Vp-p (75 Ω)

lB output level: 0.7 Vp-p (75 Ω)

lTerminal: Scart jack (1 system)

HDMI AV Output:

lTerminal: Type A connector (19 pin)

This unit supports “HDAVI Control 2” function.

Note:

1. Specifications are subject to change without notice.

Mass and dimensions are approximate.

2. Total harmonic distortion is measured by the digital spectrum analyzer.

Solder:

This model uses lead free solder (PbF).

Mechanism:

This model uses DL2S (Single tray) mechanism.

Refer to their respective original service manuals for *1, *2, *3, *4, *5, *6, *7.

SA-PT350E / SA-PT350EB / SA-PT350EG

CONTENTS

Page Page

1 Safety Precautions 6

1.1. GENERAL GUIDELINES

1.2. Before Repair and Adjustment

1.3. Protection Circuitry

1.4. Safety Parts Information

1.5. Caution for AC Cord

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

3 Precaution of Laser Diode

4 About Lead Free Solder (PbF)

4.1. Service caution based on legal restrictions

5 Handling Precautions for Traverse Unit

5.1. Cautions to Be Taken in Handling the Optical Pickup Unit

5.2. Grounding for electrostati c breakdown prevention

6 Accessories

7 Operation Procedures

7.1. Remote Control Key Buttons Operations

7.2. Main Unit Key Buttons Operations

7.3. Wireless Surround

7.4. Using the VIERA Link "HDAVI Control™"

7.5. Music Port Connection and Operation

7.6. USB Connection and Operation

7.7. Audio & Video Connections

7.8. Disc Information

8 New Features

8.1. About HDMI

8.2. Wireless Features

9 Self-Diagnosis and Special Mode Setting

9.1. Service Mode Summary Table

9.2. Service Mode Table

9.3. Wireless Service Mode Summary Table

9.4. Service Mode Table (Wireless)

9.5. DVD Self Diagnostic Function-Error Code

9.6. Sales Demonstration Lock Function

9.7. Service Precautions

10 Assembling and Disassembling

10.1. Disassembly Flow Chart

10.2. Main Components and P.C.B. Locations

10.3. Disassembly of Top Cabinet

10.4. Disassembly of the DVD Lid (When taking out disc

manually)

10.5. Disassembly of Front Panel

10.6. Disassembly of Volume P.C.B.

10.7. Disassembly of Panel P.C.B.

10.8. Disassembly of USB P.C.B.

10.9. Disassembly of Scart P.C.B.

10.10. Disassembly of Rear Panel

10.11. Disassembly of DVD Mechanism Unit

10.12. Disassembly of Relay P.C.B.

10.13. Disassembly of DVD Module P.C.B.

10.14. Disassembly of Main P.C.B.

10.15. Replacement of Regulator IC (IC2903)

10.16. Disassembly of Wi reless Adapter P.C.B.

10.17. Disassembly of D-Amp P.C.B.

10.18. Replacement of Digital Amp IC (IC5000)

10.19. Disassembly of SMPS & AC-Inlet P.C.B.

10.20. Replacement of Switch Regulator IC/Diode

(IC5701/D5702)

10.21. Replacement of Regulator Diode (D5801/D5802)

10.22. Replacement of Regulator Diode (D5803)

11 Assembly and Disassembly of DVD Mechanism Unit

11.1. Disassembly Procedure

12 Service Position

12.1. Checking & Repairing Scart P.C.B.

12.2. Checking & Repairing Panel P.C.B.

12.3. Checking & Repairing Main P.C.B.

12.4. Checking & Repairing D-Amp P.C.B.

12.5. Checking & Repairing DVD Module P.C.B.

12.6. Checking & Repairing SMPS P.C.B.

13 Measurements and Adjustments

13.1. Service Tools and Equipment

13.2. Important points in adjustment

13.3. Storing and handling of test discs

13.4. Optical adjustment

14 Abbreviati ons

15 Voltage and Waveform Chart

15.1. DVD Module P.C.B.

15.2. Main P.C.B.

15.3. D-Amp P.C.B.

15.4. SMPS P.C.B.

15.5. Panel & Tray Loading P.C.B.

15.6. Scart P.C.B.

15.7. Waveform Chart

16 Illustration of IC's, Transistors and Diodes

17 Wiring Connection Diagram

18 Block Diagram

18.1. System Control

18.2. DVD (Servo)

18.3. DVD (Audio)

SA-PT350E / SA-PT350EB / SA-PT350EG

18.4. DVD (Video) 88

18.5. DVD (HDMI)

18.6. Audio

18.7. Audio Digital Amp

18.8. Power

19 Schematic Diagram Notes

20 Schematic Diagram

20.1. DVD Module (DV5/HDMI) Circuit

20.2. Main & Panel Circuit

20.3. D-Amp & SMPS Circuit

20.4. Scart Circuit

20.5. Volume, USB, Wireless Adapter, AC-Inlet, Relay, Tray

Loading & Optical Pickup Unit Circuit

21 Printed Circuit Board

21.1. DVD Module P.C.B.

21.2. Main P.C.B.

21.3. Panel, Volume & USB P.C.B.

21.4. D-Amp P.C.B.

100

105

109

110

113

114

115

116

21.5. SMPS & Wireless Adapter P.C.B.

21.6. AC-Inlet, Scart, Relay, Tray Loading P.C.B.

22 Basic Troubleshooting Guide

22.1. Basic Troubleshooting Guide for Traverse Unit (DVD

Module P.C.B)

22.2. Basic Troubleshooting Guide for HDMI AV output

23 Overall Block Diagram for PT350W

23.1. SC-PT350W Simplified Block

23.2. SC-PT350W Power Block

23.3. SC-PT350W SMPS Block

24 Terminal Function of ICs

24.1. IC2001 (C2CBYY000418): System Control IC

25 Exploded Views

25.1. Cabinet Parts Location

25.2. Packaging (For SC-PT350WE)

26 Replacement Parts List

26.1. Component Parts List

117

118

119

120

122

123

124

125

126

127

129

130

131

SA-PT350E / SA-PT350EB / SA-PT350EG

1 Safety Precautions

1.1. GENERAL GUIDELINES

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

3. After servicing, carry out the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.1.1. LEAKAGE CURRENT COLD CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MΩ and 5.2MΩ. When the exposed metal does not have a return path to the chassis, the reading must be

1.1.2. LEAKAGE CURRENT HOT CHECK

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

Figure 1

1.2. Before Repair and Adjustment

Disconnect AC power to discharge unit AC Capacitors as such C5700, C5701 , C5703, C5704, C5705 through a 10 Ω,10W resistor to ground.

Caution:

DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.

After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

Current consumption at AC 230 V, 50 Hz in NO SIGNAL mode volume minimal should be ~ 600 mA. (For E/EG)

Current consumption at AC 240 V, 50 Hz in NO SIGNAL mode volume minimal should be ~ 600 mA. (For EB)

1.3. Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed:

· No sound is heard when the power is turned on.

· Sound stops during a performance.

SA-PT350E / SA-PT350EB / SA-PT350EG

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are

“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.

If this occurs, follow the procedure outlines below:

1. Turn off the power.

2. Determine the cause of the problem and correct it.

3. Turn on the power once again after one minute.

Note:

When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

1.4. Safety Parts Information

Safety Parts List:

There are special components used in this equipment which are important for safety. These parts are marked by should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.

Reference No. Part No. Part Name & Description Remarks

340 RAE2024Z-S TRAVERSE UNIT [M] PC5701 B3PBA0000402 PHOTO COUPLER [M] PC5702 B3PBA0000402 PHOTO COUPLER [M] PC5720 B3PBA0000402 PHOTO COUPLER [M] PC5799 B3PBA0000402 PHOTO COUPLER [M]

D5701 B0FBAR000041 DIODE [M] DZ5701 ERZV10V511CS ZENER [M] TH5701 D4CAC8R00002 THERMISTOR [M] TH5860 D4CC11040013 THERMISTOR [M]

L2101 J0JBC0000015 CHIP INDUCTOR [M] L2201 J0JBC0000015 CHIP INDUCTOR [M] L2802 J0JBC0000015 CHIP INDUCTOR [M] L2803 J0JBC0000015 CHIP INDUCTOR [M] L2804 J0JBC0000015 CHIP INDUCTOR [M] L5001 G0B9R5K00003 LINE CHOKE COIL [M] L5002 G0B9R5K00003 LINE CHOKE COIL [M] L5201 G0B9R5K00003 LINE CHOKE COIL [M] L5301 G0B9R5K00003 LINE CHOKE COIL [M] L5701 ELF15N035AN LINE FILTER [M] L5702 ELF22V035B COIL [M] L6101 J0JBC0000019 CHIP INDUCTOR [M] L6201 J0JBC0000019 CHIP INDUCTOR [M] L6801 J0JBC0000019 CHIP INDUCTOR [M] L6904 J0JBC0000019 CHIP INDUCTOR [M] L6905 J0JBC0000019 CHIP INDUCTOR [M] L6906 J0JBC0000019 CHIP INDUCTOR [M] L6907 J0JBC0000019 CHIP INDUCTOR [M] L6908 J0JBC0000019 CHIP INDUCTOR [M]

L6909 J0JBC0000019 CHIP INDUCTOR [M] T2900 G4D1A0000117 SWITCHING TRANSFORMER [M] T5701 ETS42BN1A6AD MAIN TRANSFORMER [M] T5751 ETS19AB236AG BACK-UP TRANSFORMER [M]

F1 K5D502BNA005 FUSE [M]

FP2900 K5G401A00008 FUSE PROTECTOR [M]

P5701 K2AA2B000015 JACK AC INLET [M]

A2 K2CQ2CA00007 AC CORD [M] EG/E

A2 K2CT3CA00004 AC CORD [M] EB C5700 F1BAF1020020 1000P [M] C5701 ECQU2A334MLA 0.33 [M] C5703 ECQU2A104MLC 0.1 [M] C5704 F1BAF1020020 1000P [M] C5705 F1BAF1020020 1000P [M]

in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts

Table 1

SA-PT350E / SA-PT350EB / SA-PT350EG

1.5. Caution for AC Cord

(For United Kingdom)

("EB" area code model only)

For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer.

CAUTION!

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE SOCKET.

If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red.

A A

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF KEEP DRY.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

Figure A Figure B

Fuse cover

2. Replace the fuse and close or attach the fuse cover.

Figure A Figure B

Fuse (5 ampere)

SA-PT350E / SA-PT350EB / SA-PT350EG

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applyin g power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution:

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

SA-PT350E / SA-PT350EB / SA-PT350EG

3 Precaution of Laser Diode

SA-PT350E / SA-PT350EB / SA-PT350EG

4 About Lead Free Solder (PbF)

4.1. Service caution based on legal restrictions

4.1.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that of the normal solder.

Definition of PCB Lead Free Solder being used

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder. (See right figure)

Service caution for repair work using Lead Free Solder (PbF)

· The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

· To put lead free solder, it should be well molten and mixed with the original lead free solder.

· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt

the lead free solder.

· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30

degrees C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

· The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K-----------(0.3mm 100g Reel)

RFKZ06D01K-----------(0.6mm 100g Reel)

RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

SA-PT350E / SA-PT350EB / SA-PT350EG

5 Handling Precautions for Traverse Unit

The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid caution to electrostatic breakdown when servicing and handlin g the laser diode in the Traverse unit.

5.1. Cautions to Be Taken in Handling the Optical Pickup Unit

The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body. Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.

1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.

2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed should be short-circuited with a short pin or a clip.

3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.

4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexible cable, cut off the antistatic FPC.

5.2. Grounding for electrostatic breakdown prevention

Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity in the working environment. Proceed servicing works under the working environment where grounding works is completed.

5.2.1. Worktable grounding

1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.

5.2.2. Human body grounding

1. Use the anti-static wrist strap to discharge the static electricity form your body.

SA-PT350E / SA-PT350EB / SA-PT350EG

6 Accessories

· Note: Refer to “Replacement Parts List” (Section 26) for the part number.

Remote control

AC cord

(For EB area only)

Antenna wire

AC cord

(For E, EG areas)

AC clamp filter *1 (For E, EG areas)

AC clamp filter *1

(For EB area only)

Din adaptor

(For EB area

only)

Speaker label

· Special Note: *1 AC clamp filter is to be attached to the AC cord used for the wireless receiver unit (SE-FX65).

7 Operation Procedures

7.1. Remote Control Key Buttons Operations

SA-PT350E / SA-PT350EB / SA-PT350EG

Telev i s i o n o p e r a t i o n s

Switch the main unit on or off

Change the television’s video input mode

Select disc’s title numbers and etc.,

Enter numbers

Select preset radio stations

or program list

Show on-screen menu

Show the display on the main unit,

Set the sleep timer

This function enables you to turn off the unit

automatically after the set time

SLEEP 30 SLEEP 60 SLEEP 90

OFF SLEEP 120

To cancel the timer

Press and hold [ SLEEP] to select "OFF".

To confi rm the remaining time

Press and hold [ SLEEP] again.

Adjust the television volume

Select the source

DVD: DVD/CD FM EXT-IN: USB , AV

D-IN, MUSIC P.

Start up and play a disc automatically, Control both the home theater system and the television

Adjust the volume of the main unit

Basic operations for play

Show a disc top menu

Show a disc menu or play list

Select or confirm menu items on the television screen , Frame-by-frame

Return to previous screen Show the Setup menu

To mute the sound

To cancel

Press [MUTING] again or adjust the volume. Muting is cancelled when you switch the unit to standby.

, AUX,

"AV" works only when the scart cable is connected.

SA-PT350E / SA-PT350EB / SA-PT350EG

7.2. Main Unit Key Buttons Operations

Standby/on switch [ /I]

Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.

MUSIC PORT jack

Connect an external device

/ TUNE MODE / FM MODE

Stop playback, Select the tuning mode, Adjust the FM reception condition

/MEMORY

Disc playback, Memorise the receiving radio stations

AC supply indicator [AC IN]

This indicator lights when the unit is connected to the AC mains supply.

OPEN/CLOSE

Open or close the disc tray

Display

Remote control signal sensor

Skipping or slow-search play,

/ TUNE

Select the radio stations

SELECTOR

DVD/CD USB FM AV

MUSIC P. D-IN (Digital In) AUX

VOLUME , +

Turn the volume up or down

USB jack

Connect a USB device

"AV" works only when the scart cable is connected.

Headphones

(not included)

Headphone plug type:

3.5 mm stereo mini plug Reduce the volume before connecting. Audio is automatically switched to 2-channel stereo. To prevent hearing damage, avoid listening for prolonged periods of time.

7.3. Wireless Surround

7.3.1. Wireless System Key Buttons Operations

The illustration shows the wireless system for SH-FX65.

AUTO OPERATION ON/OFF indicator

The indicator lights red when the wireless system is turned on and lights green when the wireless link is activated. When the wireless link is inactive for a long time, it turns red.

7.3.2. Digital Transmitter Connection (SH-FX65T)

Digital

Transmitter

Front panel of this unit

COMPONENT VIDEO OUT

SA-PT350E / SA-PT350EB / SA-PT350EG

Unit on/off button [ , ]

Use this button to turn the wireless system on and off.

: The unit is on.

: The unit is off.

Digital transmitter

Insert fully until you hear a click.

ANT

Digital

Transmitter

Insert the digital transmitter into the slot.

Do not insert or remove while the main unit is on.

Rear panel of this main unit

SA-PT350E / SA-PT350EB / SA-PT350EG

7.4. Using the VIERA Link “HDAVI Control™”

What is VIERA Link "HDAVI Control"?

VIERA Link "HDAVI Control" is a convenient function that offers linked operation of this unit, and a Panasonic television (VIERA) under "HDAVI Control". You can use this function by connecting the equipment with the HDMI cable. See the operating instructions for connected equipment for operational details. This unit supports "HDAVI Control 2" function. The TV with "HDAVI Control 2" function enables the following operation: VIERA Link Control only with TV’s remote control (for "HDAVI Control 2") ( see right)

Preparation

Confirm that the HDMI connection ( O/I page 13)

has been made. Confirm that the scart cable is not connected. Set "VIERA Link" to "On" ( , "HDMI" tab).

O/I page 27 To complete and activate the connection correctly, turn on all VIERA Link "HDAVI Control" compatible equipment and set the television to the corresponding HDMI input mode for the home theater system.

Whenever the connection or settings are changed, reconfi rm the points above.

One Touch Play

You can turn on the home theater system and television, and start playing the disc in the play position with a single press of a button.

Theater speakers will be automatically activated ( see below).

This function also works if you press [ , PLAY] on the home theater remote control during home theater standby mode.

Note

Playback may not be immediately displaye d on the television. If you miss the beginning portion of playback, press [ to go back to where playback started.

] or [ ]

Auto input switching

When you switch the television input to:

TV tuner mode, the home theater system will automatically switch to "AUX " or "D-IN ". HDMI input mode for the home theater system, the home theater system will automatically switch to "DVD/CD" if it is in "AUX

" or "D-IN " mode. When you start disc play, the television will automatically switch to the HDMI input mode for the home theater system. To toggle the mode that this function works with, press [ SETUP] while the main unit is in "AUX " or "D-IN" mode.

The default setting is "AUX ".

Speaker control

You can select whether audio is output from the home theater system or the television speakers by using the television menu settings. For details, refer to the operating instructions of your television.

Home Cinema

Theater speakers are active.

When the home theater system is in standby mode, changing the television speakers to theater speakers in the television menu will automatically turn the home theater system on and select "AUX The television speakers are automatically muted. You can control the volume setting using the volume or mute button on the TV’s remote control. (The volume level is displayed on the main unit’s FL display.) To cancel muting, you can also use the home theater control.

(O/I page 17) If you turn off the home theater system, television will be automatically activated.

" or "D-IN " as the source.

speakers

remote

Television speakers are active.

The volume of the home theater system is set to "0".

This function works only when "DVD/CD", "USB", "AUX " or "D-IN " is selected as the source on the home theater system.

Audio output is 2-channel audio.

When switching between the theater and television speakers, the TV screen may be blank for several seconds. To toggle which input source the main unit will automatically switch to, press [ SETUP] while the main unit is in "AUX " or "D-IN" mode.

The default setting is "AUX".

Power off link

When the television is turned off, the home theater system goes into standby mode automatically.

This function works only when "DVD/CD", "USB", "AUX " or "D-IN " is selec ted as the source on the home theater system. When the television is turned on, the home theater system does not turn on automatically. (Power on link is not available.) For "AUX" or "D-IN" mode, power off link can be set to work with one or the other. To toggle the mode that this function works with, press [ SETUP] while the main unit is in "AUX" or "D-IN" mode.

The default setting is "AUX".

Note

Only the home theater system turns off when you press [ ] for shutting it down. Other c onnec ted equipment compatible with VIERA Link "HDAVI Control" stay on.

VIERA Link Control only with TV’s remote control (for "HDAVI Control 2")

You can control the disc menus of the home theater system with the TV s remote control when using the "DVD/CD" or "USB" source. When operating the TV’s remote control, refer to the below illustration for operation buttons.

the television menu settings. (For details, refer to the operating instructions of your television.)

The home theater system will

automatically switch to "DVD/CD" if it

is in "AUX

To toggle the mode that this function works with, press

" or "D-IN ".

[ SETUP] while the main unit is in "AUX" or "D-IN" mode.

The default setting is "AUX".

2. Select the desired item.

"TOP MENU"

: Shows a disc

top menu (O/I page 19, 21) or program list (O/I page 22).

"MENU"

: Shows a disc menu

(O/I page 19, 22) or play list (O/I page 22).

"Control Panel"

: The basic operations

for discs are available.

Note

Depending on the menu, some button operations cannot be performed from the TV’s remote control. "Control Panel" can be selected directly by using a button on the TV s remote control (e.g. [OPTION] ).

1. Select the theater operation menu by using

ENTER/ PLAY

RETURN

7.5. Music Port Connection and Operation

SA-PT350E / SA-PT350EB / SA-PT350EG

The Music Por t allows you to connect and enjoy music from an external device (example: MP3 player) through your home theater system.

Preparation

To avoid distorted sound, make sure that any equalizer function of your external device is turned off.

1 Reduce the volume and connect the external device

(not included).

Plug type

3.5 mm stereo mini plug

External device

(not included) Reduce the volume

before connecting.

2 To select "MUSIC P.".

USB AUX D-IN (Digital In)

MUSIC P.

3 Adjust the external device volume to a normal listening

level, and then adjust the volume of the main unit.

You can enjoy surround sound when you turn on Super Surround (MOVIE, MUSIC) (O/I page 32).

SA-PT350E / SA-PT350EB / SA-PT350EG

7.6. USB Connection and Operation

The USB connectivity enables you to connect and play tracks or files from USB mass storage class devices. Typically, USB memory devices. (Bulk only transfer)

Preparation

Before connecting any USB mass storage device to the unit, ensure that the data stored therein has been backed up.

It is not recommended to use a USB extension cable. The USB device is not recognised by this unit.

1 Connect the USB mass storage device (not included).

USB enabled device

(not included) It is not recommended to use a

USB extension cable. The device connected via the cable will not be recognised by this unit.

2 To select "USB" as the source, press several times.

3 Adjust the volume of the main unit.

4 Begin playback by selecting the track from the USB

mass storage device.

To return to the previous screen

Press [ RETURN]

For other operating functions, they are similar as those described in "DISC OPERATIONS" ( O/I page 18 to 30).

USB AV AUX D-IN (Digital In)

MUSIC P.

Compatible Devices

Devices which are defined as USB mass storage class:

USB devices that support bulk only transfer. USB devices that support USB 2.0 full speed.

Supported Formats

File name tFile ex ension

Still pictures JPG .jpg .jpeg

Music MP3

WMA

Video MPEG4 .asf

For Panasonic D-Snap/DIGA

.mp3 .wma

Note

CBI (Control/Bulk/Interrupt) is not supported. Digital Cameras that use PTP protoc ol or which require additional program installation when connected to a PC are not supported. A device using NTFS file system is not suppor ted. [Only FAT 12/16/32 (File Allocation Table 12/16/ 32) file system is supported]. Depending on the sector size, some files may not work. It will not operate with Janus enabled MTP (Media Transfer Protocol) devices. Maximum folder: 400 fo Maximum : 4000 Maximum name: 44 charac ters Maximum folder name: 44 characters Only one memory card will be selected when connecting a multiport USB card reader. Typically the first memory card inserted.

file

lders

files

7.7. Audio & Video Connections

7.7.1. Television with an HDMI Terminal

Television with an HDMI terminal

HDMI-compatible

television

(not included)

SA-PT350E / SA-PT350EB / SA-PT350EG

AV IN

HDMI cable (not included)

AV OUT

Use the HDMI connection to enjoy higher quality audio and video with a single cable.

Set "Video Mode" to "On" and "Audio Output" to "On"

(O/I page 27,

Set "Video Output Mode" ( Picture Menu).

"HDMI" tab)..

O/I page 24,

VIERA Link ("HDAVI Control")

If your Panasonic television is a VIERA Link compatible television, you can operate your television synchronising with home theater operations or vice versa (O/I page 36).

Note

Make the ex tra audio connection (O/I page 34) when you use "HDAVI

Control" function. It is recommended that you use Panasonic’s HDMI cable. [Recommended par t number: RP-CDHG15 (1.5 m), RP-CDHG30 (3.0 m),

RP-CDHG50 ( 5.0 m), etc.] Non-HDMI-compliant cables cannot be utilised.

7.7.2. Optional Connection for Set Top Box, Cable TV, or Video Cassette Recorder

Set top box

(not included)

Television

(not included)

Rear panel of this main unit

SCART cable (not included)

SCART cable

(not included)

To listen to the sound from the television, select the appropriate audio out (example: Monitor) on the television.

Sound from the television

Press [EXT-IN] (O/I page 37) to select the "AV" audio input on the remote control.

7.7.3. Optional Audio Connection for Video Cassette Recorder or Television

Press [EXT-IN] (O/I page 17) to select "AUX" as the source to operate the audio input.

This audio connection will enable you to play audio from your video cassette recorder or television through your home theater system.

Video cassette

recorder/ TV

(not included)

Rear panel of this main unit

Audio cable

(not included)

SA-PT350E / SA-PT350EB / SA-PT350EG

7.8. Disc Information

7.8.1. Disc Playability (Media)

Commercial discs

Disc Logo

Indicated in

these

instructions by

Remarks

DVD-Video

Video CD

Recorded discs

( : Playable, : Not playable)

Recorded on a DVD

Disc Logo

video recorder, etc.

DVD- RAM

DVD- R/ RW

DVD- R DL

+R/+RW Necessary

+R DL Necessary

CD-R/RW Necessary

High quality movie and music disc s.

Music discs with video. Including SVCD (Conforming to IEC62107).

Music discs.

Recorded on a personal computer, etc.

()

9, 10

Finalizing

Not

necessary

Necessary

It may not be possible to play all the above-mentioned discs in some cases due to the type of disc, the condition of the recording, the recording method, or how the files were created [Item 7.8.2 File Extension Type Support (WMA/MP3/JPEG/

MPEG4/DivX]

This unit can play CD-R/RW recorded with CD-DA or Video CD format.

This unit also plays HighMAT discs.

Discs recorded on DVD video recorders or DVD video cameras, etc. using Version 1.1 of the Video Recording Format (a uni ed video

recording standard).

Discs rec orded on DVD video re corders or DVD video cameras using Version 1.2 o f the Video Recording Format (a uni efi d video

recording standard).

Discs recorded on DVD video recorders or DVD video cameras using DVD-Video Format.

Recorded using a format dif ferent from DVD-Video Format, therefore, some func tions cannot be used.

A process that allows play on compatible equipment. To play a disc that is displa yed as "Necessary" on this unit, the disc must rfi st be

nfi alized on the device it was recorded on.

Closing the session will also work.

MPEG4 data recorded with the Panasonic SD multi cameras or DVD video recorders [conforming to SD VIDEO specifications (ASF

standard)/ MPEG4 (Simple Profile) video system /G.726 audio system].

Functions added with DivX ultra are not supported.

Plays all versions of DivX

video (including DivX 6 ) with standard playback of DivX media lfi fies. Certi ed to the DivX Home Theater

Profile.

Note about using a DualDisc

The digital audio content side of a DualDisc does not meet the technical specifi cations of the Compac t Disc Digital Audio (CD-DA) format so playback may not be possible.

Discs that cannot be played

DVD-RW version 1.0, DVD-Audio, DVD-ROM, CD-ROM, CDV, CD-G, SACD, Photo CD, DVD-RAM that cannot be

Video systems

This unit can play PAL and NTSC, but your television must match the system used on the disc. PAL discs cannot be correctly viewed on an NTSC television. This unit can convert NTSC signals to PAL 60 for viewing on a PAL television (O/I page 27, "NTSC Disc Output" in "Video" tab).

removed from their cartridge, 2.6-GB and 5.2-GB DVDRAM, and Chaoji VCD available on the market including CVD, DVCD and SVCD that do not conform to IEC62107.

7.8.2. File Extension Type Support (WMA/MP3/JPEG/*MPEG4/*DivX)

When there are more than eight groups, the eighth group onwards will be displayed on one vertical line in the menu screen. There may be differences in the display order on the menu screen and computer screen. This unit cannot play lfi es recorded using packet write.

DVD-RAM

Discs must conform to UDF 2.0.

DVD-R/RW

Discs must conform to UDF bridge (UDF 1.02/ISO9660). This unit does not support multi-session. Only the default session is played.

CD-R/RW

Discs must conform to ISO9660 level 1 or 2 (except for extended formats). This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the number of sessions to a minimum to avoid this.

Naming folders and files

SA-PT350E / SA-PT350EB / SA-PT350EG

Files are treated as contents and folders are treated as groups on this unit.

At the time of recording, prefi fix folder and le names. This should be with numbers that have an equal number of digits, and should be done in the order you want to play them (this may not work at times). Files must have the extension ( see below).

(Extension: ".WMA" or ".wma")

Compatible compression rate: bet ween 48 kbps and 320 kbps. You cannot play WMA files that are copy-protected. This unit does not support Multiple Bit Rate (MBR).

(Extension: ".MP3" or ".mp3")

Compatible compression rate: bet ween 32 kbps and 320 kbps. This unit does not support ID3 tags. Compatible sampling rates:

DVD-RAM, DVD-R/RW: 11.02, 12, 22.05, 24, 44.1 and 48 kHz

CD-R/RW: 8, 11.02, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz

(Extension: ".JPG", ".jpg", ".JPEG" or ".jpeg")

JPEG lfi es taken on a digital camera that conform to DCF Standard (Design rule for Camera F ile system) Version 1.0 are displayed. Files that have been altered, edited or saved with computer picture edi ting software may not be displayed. This unit cannot display moving pictures, MOTION JPEG and other such formats, and still pictures other than JPEG (Example: TIFF), or play pictures with attached audio.

(Extension: ".ASF" or ".asf")

You can play MPEG4 data [conforming to SD VIDEO speci cfi ations (ASF standard)/MPEG4 (Simple Pro le) video system/G.726 audio system] recorded with Panasonic SD multi cameras or DVD video rec orders with this unit. The recording date may differ from that of the actual date.

(E xtens ion: ".DIVX", ".divx", ".AVI" or ".av i")

You can play all versions of DivX system] with standard playback of DivX

DivX les greater than 2 GB or have no index may not be played properly on this unit.

fi This unit supports all resolutions up to maximum of 720 x 480 (NTSC)/720 x 576 (PAL). You can select up to eight types of audio and subtitles on this unit.

video (including DivX 6) [DivX video system/MP3, Dolby Digital or MPEG audio

media lfi es. Functions added with DivX Ultra are not supported.

Example:

root

For E/EG only

SA-PT350E / SA-PT350EB / SA-PT350EG

8 New Features

8.1. About HDMI

8.1.1. What is HDMI?

8.1.2. Advanced Digital Pictures

8.1.3. Advanced Digital Sound

SA-PT350E / SA-PT350EB / SA-PT350EG

8.1.4. Easy to Use

8.1.5. HDMI Compatible Products

SA-PT350E / SA-PT350EB / SA-PT350EG

8.2. Wireless Features

8.2.1. Function Overview

Year 2007 PT models support wireless which includes FX65/FX66, wireless subwoofer and FX85 as described below:-

8.2.1.1. FX65/FX66

· The FX65/FX66 supports one-way wireless transmission only, that is, it will only transmit wireless audio signal to the rear

surround speakers. The FX65/FX66 receiver module includes a D-AMP and SMPS. The transmitter interfaces with the main unit using serial communications to communicate information such as mute command request, link detection and ID setting request. Maximum range attainable is 15 meters.

8.2.1.2. Wireless Subwoofer (For PT1050 Only)

· The wireless subwoofer receiver module is similar in operation with FX65/FX66 in such a way that it only supports one-way

wireless transmission. It also includes a D-AMP and SMPS. The differe nce in the wireless subwoofer receiver module is the way its hardware interprets the audio it receives from the transmitter since it is the same audio received by the FX65/FX66 receiver. Maximum range attainable is 30 meters.

8.2.1.3. FX85

· The FX85 supports the multi-room function wherein it operates as a second room wireless receiver (up to a maximum of two).

Maximum range attainable is 30 meters. It can send commands to the main unit to control functions such as Play, Stop, Forward Skip/Channel Up, Reverse Skip/Channel Down. It also has a built-in DAP pocket for stand-alone operation by inserting a DAP device (e.g. iPod) in the DAP pocket to play the device only via the device’s own control button s, FX85 cannot control the device using its own buttons. The transmitter interfaces with the main unit using serial communications to communicate information such as mute command request, link detection, ID setting request and button commands from the FX85 buttons (Play, Stop, Forward Skip/Channel Up, Reverse Skip/Channe l Down). The FX85 receiver module has the following functions/terminals/buttons:

FX85 BUTTONS FX85 FUNCTIONS FX 85 Power Button D-Amp Selector Button SMPS Play Button D-Port Connector Stop Button ID Set Switch Forward Skip/Channel Up MPort Reverse Skip/Channel Down Volume Control

SA-PT350E / SA-PT350EB / SA-PT350EG

8.2.2. Block Diagram

· There are two types of transmitter cards, Type A and Type B, and two types of receiver modules, Type 1 and Type 2 for the

wireless configuration. The block diagrams below describe the differe nces of each of the types.

8.2.2.1. TX-TYPE A / RX-TYPE 1

Note:

EEPROM

- One way only

- FX65/FX66 signal flow

- FX65/FX66 only

MCU

ADC

CH2 IN

TX Type A

· Type A transmitter uses one ADC (Analog to Digital Converter) and transmits audio through Chann el 2. Type 1 receiver (Rx)

uses one DAC and output audio through Channel 2. The firmware (that is downloaded to EEPROM IC) multiplexes which channel to listen to (in this case Channel 2 since type A is transmitting from channel 2 In) by setting the baseband accordingly.

DAC

CH2 OUT

RX Type 1

MCU

SA-PT350E / SA-PT350EB / SA-PT350EG

8.2.2.2. TX-TYPE B / RX-TYPE 2

EEPROM

MCU

ADC

DAC

EEPROM

MCU

Note:

- FX65/FX66 SIGNAL FLOW

- FX85 S

- ONE WAY AND SIMULTANEOUS

- FX65/FX66 + FX85

- FX65/FX66 TRANSMITTER NOT USED, NEED TO IDSET FX65/FX66

- TX TYPE B BUT RX CHANGED FROM TYPE 2 TO TYPE 1, CH1 SIGNAL REDIRECTED TO DAC

IGNAL FFLOW

CH2 IN

CH1 IN

TX Type B

CH2 OUT

RX Type 2

· Type B transmitter uses two ADC (Analog to Digital Converter) to send audio streams from Channel 1 and Chann el 2 for the

FX65/FX66 surround sound and FX85 second room audio, respectively. Type 2 receiver outputs audio through Channel 2. The software multiplexes which channel to listen to by setting the baseband accordingly. For example, if the receiver is configured as an FX85 receiver (Type 2), the baseband is configu red to accept Channel 1 audio transmission and redirect it to Chann el 2 Out. If the receiver is set as an FX65/FX66 or wireless subwoofer, the baseband is configu red to accept channel 2 audio transmission and redirect it to the same Channel 2 Out.

8.2.3. Activation

· FX65/FX66 can be activated in the main unit by using either transmitter Type A or Type B and enabling surround sound by

selecting Surround Music, DPL or Super Surround (Music/Movie).

· FX85 Wireless feature is enabled by default when the user uses transmitter type B.

8.2.4. LED Indication

· For FX65/FX66, there will be two-color LED that will be used to indicate Power On and Link. If link, the two-color LED will be

green, else, it will be red.

For FX85, the front panel will have LED indicators for Standby,, Wireless Link, Charge, Option and Music Port. During Power On, Standby LED will be OFF. Only during power OFF will this LED be ON (Red). Wireless Link indicator will be ON (Green) when link is established between TX and RX and OFF when link is lost. Pressing the selector button will toggle from any of the selector modes Wireless, Option and Music port. Only the currently selected mode will be ON (Green), the other two will be OFF. Charge LED will be ON (Red) once iPod charging is initiated.

8.2.5. Key Operation (FX85)

· Selector Button

This button will be used to select Wireless, Option or M.Port and enabling the corresponding LED indicators for each mode. During Power On, by default, selector mode is set to Wireless when power is initially supplied to the system. But during Power On/OFF button, it will remember the last selector mode setting.

· Play Button

SA-PT350E / SA-PT350EB / SA-PT350EG

This button will send command to the main unit to play CD/DVD as well as the iPod. This function is therefore meaningful only if the second room selector is in Main Source (with the first room user in CD/DVD or iPod) and iPod.

· Stop Button

This button will send command to the main unit to stop CD/DVD as well as the iPod. This function is therefore meaningful only if the second room selector is in Main Source (if the first room user is in CD/DVD mode or iPod) and iPod.

· Forward Skip/Channel Up

This button depends on the second room source currently selected. It will be interpreted as a Forward Skip by the main unit if the second room source is in Main Source (with the first room user is in CD/DVD or iPod mode) and iPod. It will be interpreted as a Channel Up (preset channels only) if the second room source is in FM, AM, or XM.

· Reverse Skip/Channel Down

This button depends on the second room source currently selected. It will be interpreted as a Reverse Skip by the main unit if the second room source is in Main Source (if the first room user is in CD/DVD or mode) and iPod. It will be interpreted as a Channel Down (preset channels only) if the second room source is in FM, AM, or XM.

· Volume Control

Volume control will be local to the FX85 module only. Default volume (TBD) will be set every time power is first supplie d to the system or during exit from stand by mode.

· ID-setting Operation

ID setting operation can be invoked by pressing fast-forward key in the main unit and three [3] key in the remocon. Once IDsetting is triggered, the receiver must press its ID-setting button within 60 seconds. During this period, the transmitter will be in open connect mechanism whereby any receiver can pair with the transmitter. After this period elapsed, the transmitter will revert back to using close connect code whereby only those receivers which have the same ID as the transmitter will be able to link. The user also has the option to exit the ID setting operation by pressing the same keys.

· iPod Detection and Charging

iPod is detected once inserted on the FX85 and battery charging automatically starts.

−

− The iPod Charging in Standby Mode:

− −

lUpon iPod insertion detection and FX85 is in Power OFF (stand by), FX85 set will enter iPod charging Standby Mode.

lThe FX85’s CHARGE LED will light up whenever the iPod is charging.

lFX85 will charge the battery up to five hours. After this period, FX85 will not try to recharge the iPod.

lAfter battery full condition, even if the iPod is operated such as play, FX85 will not retry to recharge the iPod (timer will start

immediately once iPod is inserted).

lRe - charging of the battery in iPod Charging Standby Mode can be done only by removing and reinserting the iPod to the dock.

−

− The iPod charging in Power On Mode:

− −

lThe iPod automatically charges its battery whenever it is connected during Power ON.

lThe FX85’s CHARGE LED will light up whenever the iPod is charging.

lFX85 will continue charging the iPod as long as it is inserted (no charging time limit of five hours).

SA-PT350E / SA-PT350EB / SA-PT350EG

8.2.6. FX Configurations

There are four types of configurations for the FX series. This is explained by the following illustrations below:

Case 1: FX65/FX66

· This is the basic configuration of FX65/FX66 whereby it is only receiving wireless surround audio signal from the main set. This

uses a Type A transmitter which is only able to send audio in one direction. Audio is sent using streams AB through Ch 2.

FX65/FX66

CH2/AB

Case 2 A: FX65/FX66 + FX85

· In this configuration, a second receiver, an FX85, in another room is listening to another audio source from the main set. The

FX85 also is able to send command to the main set such as Play, Stop, Skip, and Preset Tuner Chann el Up/Down. This configuration uses Type B transmitter which is an upgrade of the Type A and can be used on Type 1 (FX65/FX66). This transmitter is able to send audio signal for second room via Ch 1 and first room via Ch 2.

In this configuration, streams AB is used to transmit the audio from main unit to the first room Type 1 receiver (FX65/FX66) via Ch 2. While the second room audio is transmitted through stream CD via Ch 1.

Multi-room + Multi source

CH1/CD

CH2/AB

FX65/FX66

Case 3 A: Wireless Subwoofer

· This configuration, Type A transmitter send signals to subwoofer and Type 1 receiver (FX65/FX66) via channel 2, which is the

same audio signals sent to FX65/FX66 as well. The subwoofer only decodes the low frequency signal.

FX85

+ 114 hidden pages