Panasonic PV-C1322K, PV-C1352WK Operating Instructions

Combination VCR

Operating Instructions

Initial Setup

Models No. PV-C1322-K/PV-C1352W-K

Initial Setup and Connection Procedures are on pages 8 to 13.

Basic Operation

TV Operation

Timer Operation

Advanced Operation

As an ENERGY STAR Partner, Panasonic has determined that this product or product model meets

E

NERGY STAR guidelines for energy efficiency.

the

Please read these instructions carefully before attempting to connect, operate, or adjust this product. Please save this manual.

For Your Information

LSQT0601A

Important Safeguards and Precautions

READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric Utility Service Company or Video Products Dealer verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug. Always hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord. Regularly remove dust, dirt, etc. on the plug.

POLARIZED PLUG CAUTION:

The plug fits into the outlet only one way. If it cannot be fully inserted, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not tamper with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against electrical shock, fire, or personal injury:

- Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type plug (polarized or grounding) and must be securely connected.

- Overloaded wall outlets or extension cords are fire hazards.

- Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during operation. If blocked, heat build-up may result in a fire hazard or heat damage to cassettes. For your protection: a. Never cover ventilation slots while unit is ON,

or operate unit while placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless properly ventilated.

5

AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator, in direct sunlight, etc. If unit is suddenly moved from a cold place to a warm place, moisture may condense in unit and on the tape causing damage.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• Move any appliance and cart combination with care. Quick stops, excessive force, and uneven surfaces may cause objects to overturn.

• Carefully follow all operating instructions.

2

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly grounded to provide some protection against built up static charges and voltage. Part 1 of the Canadian Electrical Code, in U.S.A. Section 810 of the National Electrical Code. ANSI/NFPA 70 provides information regarding proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE

POWER LINES OR CIRCUITS

Locate an outside antenna system well away from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could be fatal.

ELECTRIC SERVICE EQUIPMENT

NEC

- NATIONAL ELECTRICAL CODE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

USING THE UNIT

Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safeguards.

1 KEEP UNIT WELL AWAY FROM WATER OR

MOISTURE,

2 IF EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT,

by a qualified service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises. Immediately unplug unit, and have it inspected by a service technician to avoid potential fire and shock hazards.

•

Never drop or push any object through openings in unit. Touching internal parts may cause electric shock or fire hazard.

• Keep magnetic objects, such as speakers, away from unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into unit and cause electrical shock. Any substance, such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

such as vases, sinks, tubs, etc.

unplug unit and have it inspected

SERVICE

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating instructions, the unit does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug unit and contact a qualified service technician.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts specified by the manufacturer, or have equal safety characteristics as original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a thorough safety check be done as described in the manufacturer’s service literature to ensure video unit is in safe operating condition.

Safety Precautions

Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.

This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS equipment. Only use those tapes with the only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television receiver provides display of television closed captioning.

mark. It is recommended that

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit.

Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No. Model No. Serial No.

Accessories

SLEEP

POWER

EJECT NITE

DISPLAY

1

2

POSITION

TAPE

5

4

COUNTER

8

7

RESET

ADD/DLT

R-TUNE

100

0

MUTE

SEARCH

C H

SELECT

VOL

ACTION

C H

PLAY

REW/

STOP

REC

PAUSE/ SL O

W

CM/ZERO

3

TRACKING

6

9

PROG

FF/

SPEEDFM/TV

Remote Control LSSQ0281

(PV-C1322-K)

LSSQ0282

(PV-C1352W-K)

Batteries 2 “AA”

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Prevent

Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screwdriver

To record again.

Cover the hole with cellophane tape.

3

Location of Controls

Remote Control Buttons

EJECT button:

When EJECT is pressed, the tape is ejected from Cassette Compartment. If EJECT is pressed during recording, the unit will not respond to the command.

EJECT

Ejects tape.

POWER

Turn unit on or off.

DISPLAY

Displays the VCR status and clock.

TAPE POSITION

Finds out present tape position and amount of tape remaining.

COUNTER RESET

Resets to “0:00:00” at the desired position.

RAPID TUNE

Displays the last channel you were watching.

MUTE

Mutes the sound instantly.

VOLUME UP/DOWN

Adjusts volume.

SET/BACK SPACE

Sets a selected menu, or goes back to correct.

ACTION

Displays main menu.

STOP

Stops recording or playback.

REC

Records the program.

REWIND/SEARCH

Rewinds tape, and searches reverse scene.

FM/TV

Receives FM radio signal.

POWER

DISPLAY

TAP E

COUNTER

RESET

R-TUNE

MUTE

ACTION

STOP

REC

POSITION

VOL

EJECT NITE

1

4

7

100

C H

SELECT

C H

REW/

PAUSE/SLO

2

PLAY

5

8

0

VOL

W

SLEEP

3

6

9

ADD/DLT

SEARCH

PROG

FF/

CM/ZERO

SPEEDFM/TV

TRACKING

NITE

Colour and picture intensity level are adjusted during night time use.

SLEEP

Turns off the unit automatically.

TRACKING UP/DOWN

Reduces picture noise during Playback and Slow Motion.

NUMBER keys

Selects a channel directly.

ADD/DELETE

Adds or deletes a channel.

SEARCH

Goes directly to the desired recording. Locates end point of recording.

CHANNEL UP/DOWN

Selects a channel.

SELECT UP/DOWN

Control the navigation around on-screen menu.

PROGRAM

Displays SET PROGRAM screen. You can set Timer Program and On-Timer.

FAST FORWARD/SEARCH

Fast forwards tape, and searches forward scene.

CM/ZERO

In Stop mode, goes to the counter “0:00:00.” In Play mode, skips over 1 to 3 minutes of tape.

SPEED

Selects recording speed.

PLAY

Begins playback.

PAUSE/SLOW

Pauses for slow motion and frame advance picture.

6

Front View of the unit and Indicators on the Front Panel

VIDEO IN AUDIO IN

POWER VOL CH

STOP/EJECT REW/

PLAY/REPEAT

FF/ REC TIMER/FM

ACTION

REC ON TIMER

PROG TIMER

Initial Setup

VIDEO IN AUDIO IN

AUDIO VIDEO IN Jack

For dubbing.

POWER

See previous page.

VOLUME UP/DOWN SET/BACK SPACE

See previous page.

CHANNEL UP/DOWN TRACKING UP/DOWN SELECT UP/DOWN

See previous page.

STOP/EJECT

See previous page.

ACTION

Press together with REW.

Rear View of the Unit

POWER VOL CH

STOP/EJECT REW/

ACTION

PLAY/REPEAT

REWIND/SEARCH

See previous page.

ACTION

together with

Press STOP.

PLAY

See previous page.

REPEAT

Repeats a recording.

FAST FORWARD/ SEARCH

See previous page.

REC

See previous page.

TIMER

Sets a timer alarm up to 60 minutes.

FF/ REC TIMER/FM

REC ON TIMER

PROG TIMER

Built-In Speaker

PHONES Jack

Connect an earphone or headphones.

PROG TIMER Indicator

Lights when the unit is set for Timer Recording.

ON TIMER Indicator

Lights when the On-Timer is set.

REC Indicator

Lights during recording.

Remote Sensor

AC Power Card

When plugged into an AC outlet, the unit consumes 2.5 W of electric power in OFF condition.

Easy Grip-Handle

Use when transporting the unit.

VHF/UHF

VHF/UHF Antenna

Input Terminal

In from your Antenna or Cable.

Page 8

7

Connections/ Initial Setup (Ready to Play)

Please make all cable or antenna connections before powering on.

How to Connect

Connecting

For ANT./Cable Connect the cable from Antenna/Cable to the VHF/UHF terminal on the unit.

VHF/UHF

IN from ANT./CABLE

VHF

/

UHF

For DSS/Cable Box Connect the OUT jack on your cable box to the VHF/UHF terminal on the unit with an

cable.

RF

WARNING:

Overtightening "Nut type" RF coaxial cables may damage jacks. Finger tighten only.

Initial Setup (Ready to Play)

Plug the unit power cord into an

1

AC wall outlet.

Press Power on the remote or unit. The unit comes on and auto

2

channel and clock set starts.

CH AUTO SET PROCEEDING

• If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone. If you use a DSS receiver, it must be turned off.

UNIT

VHF/UHF

Cable TV Converter Box

VHF/UHF

V

H

F

/ U

H

F

Settings are made automatically. When setup is

3

done, this screen appears.

2 / 6 / 2002

SETT I NG : CH 1

A

UTO CLOCK SET

COMPLETED

If AUTO CLOCK SET IS INCOMPLETE screen, MANUAL CLOCK SET procedure as shown on page 9.

set the clock using

IN from ANT./CABLE

WED 12 : 00PM

DST : O

N

0

appears on

SET

CLOC

K

WED

12

DST : O

:

00

PM

N

AUTO CLOCK SET

PROCEEDING

CANCEL : PRESS STOP KEY

2 / 6/

2002

SET

COMPLETED

SET : START

:

ACT I ON

8

1 / /

ay)

VIDEO IN AUDIO IN

POWER VOL CH

STOP/EJECT REW/

PLAY/REPEAT

FF/ REC TIMER/FM

ACTION

REC ON TIMER

PROG TIMER

Manual Clock Set

If AUTO CLOCK SET was incomplete, manually set the clock as follows.

Press ACTION on the Remote to display SET CLOCK Menu screen.

1

SET

CLOC

K

TH

CLOC

WED

DST

K

DST : O

12

:

: ON

00

PM

N

1 / /

T

SELE C

MON

SELECT : SET : END

:

ACT I ON

Press and press

2

manner, select and set the date, year, time, and DST. (Daylight Saving Time)

Press ACTION twice to start CLOCK and exit.

3

to select the month

to set. In the same

SET

2 / 6/

2002

SET

COMPLETED

SET :

START

:

ACT I ON

Reset all unit Memory Functions

When moving unit to a new location, or if a mistake was made in the Initial Setup section.

• Make sure a tape is not inserted in the unit.

POWER VOL CH

STOP/EJECT REW/

FF/ REC TIMER/FM

PLAY/REPEAT

VIDEO IN AUDIO IN

Turn the unit

1

Power on.

Press and hold both PLAY and

2

FF on the unit for more than 5

ACTION

seconds.

• The power will shut off.

• Please ignore “NO CASSETTE” warning.

Do “Initial Setup” on page 8.

3

PROG TIMER

REC ON TIMER

Initial Setup

POWER

ACTION

DISPLAY

TAPE

COUNTER

RESET

ACTION

POWER

POSITION

R-TUNE

MUTE

STOP

REC

EJECT NITE

100

VOL

REW/

SLEEP

3

1

2

TRACKING

5

6

4

8

7

9

ADD/DLT

0

SEARCH

C H

SELECT

C H

PAUSE/SLO

VOL

PLAY

W

PROG

FF/

CM/ZERO

SPEEDFM/TV

SELECT/SET

:CH UP

:CH DOWN :VOL UP :VOL DOWN

Note to CABLE System Installer

This reminder is provided to call the CABLE (Cable TV) System Installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

9

Reset Language, Channels, Clock,

T

:

M A I N MENU

1

SELECT : SET :

VCR

T V

CLOC

C H

ACT

ON

I

Language

2

1) Press to select language icon.

M A I N MENU

T V

VCR

T V

CLOC

C H

SELECT : SET : ACT I ON

2) Press ACTION repeatedly.

MENU

PR I NC I PAL

T V

VCR

T V

CANAL

ELEG I R : F I JAR :

SEL. :

REGLER : ACT I O

SELECT : SET : ACT I ON

3) Press to select “EXIT.” Press ACTION to exit.

REL OJ SAL I R

ACT I O

For Spanish

MEN

ELE

T

MAGNET .

HORLOGECANAL

For French

M A I N MENU

T V

VCR

T V

CLOC

C H

For English

LANGUAGE

K

N

U

N

K

EX I T

LANGUAGE

EX I T

H

O L A

IDIOMA

BONJOUR

LAN

GU

SORT I E

H

ELL

O

LANGUAGE

EX I T

Press ACTION

to display MAIN MENU.

Channels

1) Press select “CH.”

M A I N MENU

VCR

T V

CLOC

:

T

CAPT I

C

ABLE

K

ON

SPLAY : OFF

to set your

C H

SELECT : SET : ACT I ON

2) Press ACTION.

SET UP CHA

ENNA

ANT

A

UTO SE

CHA

NNEL

W

EAK S I GNAL D I

SELECT : SET

: : ACT I ON

END

3) Press “ANTENNA,” then

press

antenna system (“TV” or “CABLE”).

E

4) Press “AUTO SET,” then press .

• After Channel Auto Set is

finished, Clock Auto Set will be performed. (If clock is set manually, Clock Auto Set will not be performed.)

to

LANGUAGE

EX I T

NNE

L

to select

Clock

1) Press to select “CLOCK.”

M A I N MENU

VCR

CLOC

K

CLOC

WED

ACT I ON

to select

start the

LANGUAGE

EX I T

JUS

T :

K

:

12

00

DST : O

0

PM

N

T V

C H

SELECT : SET : ACT I ON

2) Press ACTION.

SET CLOCK

AUTO CLOCK SET

MANU

AL

T I M

E ZONE AD

SELECT : SET

: : ACT I ON

END

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

3) Press to select “MANUAL” or “AUTO CLOCK SET” and press .

• For Auto Clock Set,

select “AUTO CLOCK SET,” then press SET.

SET

2 / 6/

2002

SELE CT

HOUR

SELECT

: SET : START

:

4) Press and press and set the month, date, year, time, and DST (Daylight Saving Time).

5) Press ACTION twice to clock and exit this mode.

10

, Time Zone Adjust

E

JUS

T

E

JUS

T

+1

VOLCHCH

EJECT NITE

100

VOL

REW/

SLEEP

3

1

2

TRACKING

5

6

4

8

7

0

C H

SELECT

VOL

C H

PLAY

W

PAUSE/SLO

9

ADD/DLT

SEARCH

PROG

FF/

CM/ZERO

SPEEDFM/TV

NUMBER Keys

ADD/DLT

SELECT/SET

:CH UP :CH DOWN :VOL UP :VOL DOWN

Basic Operation

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select “CLOCK.”

M A I N MENU

VCR

CLOC

K

LANGUAGE

EX I T

T V

C H

SELECT : SET : ACT I ON

POWER

ACTION

DISPLAY

TAPE

COUNTER

RESET

ACTION

POWER

POSITION

R-TUNE

MUTE

STOP

REC

2) Press ACTION.

SET CLOCK

AUTO CLOCK SET MANU

AL

T I M

E

SELECT : SET

: : ACT I ON

END

ZOZONE ADJUS

ACTION key on

T

: 0

the unit

Using keys

VOL

3) Press to

select TIME ZONE ADJUST and press or to subtract or add hour(s) as necessary.

SET CLOCK

AUTO CLOCK SET MANU

AL

T I M

E

SELECT : SET

:

: ACT I ON

END

ZOZONE ADJUS

T

: +1

On Unit

You can operate the menu screen using unit buttons. To display the menu, press STOP/ EJECT and REW together with no tape inserted. To exit the menu, repeat above with or without tape inserted until normal screen appears.

On Remote

: CH UP

: CH DOWN : VOLUME UP

: VOLUME DOWN

Whenever the menu or program screen is displayed, CHANNEL UP/DOWN function

and VOLUME UP/

as DOWN function as

On Unit

only.

4)Press ACTION

twice to exit.

Add or Delete a Channel

To add channel:

Select channel with number keys and press ADD/DLT.

C

HANNEL

08 ADDED

To delete channel:

Select channel with CH and press ADD/DLT.

or number keys

C

HANNEL

08 DELE T

ED

11

Playback a Tape

Record On a Tape

Ready Check List

All connections are made. Your unit is plugged in.

Insert a cassette.

1

Record tab

To prevent tape jam,

remove loose or peeling labels from tapes.

• The unit power comes on automatically.

Press PLAY.

• Playback begins if cassette has no record

2

tab.

■ Forward/Reverse scene search

=> Press FF or REW => PLAY to release.

■ Still (Freeze) picture

=> Press PAUSE/SLOW => Press PLAY to release.

■ Slow Motion picture

=> Hold down PAUSE/SLOW in

Still mode

=> Press PLAY to release.

■ Frame by Frame picture

=> Press PAUSE/SLOW in Still mode => Press PLAY to release.

Notes

• These features work best in SP or SLP mode (model PV-C1352W-K) and SLP mode (model PV-C1322K).

• After the unit is in Still or Slow mode for 3 minutes, it will switch to Stop mode automatically to protect the tape and the video head.

■ Stop => Press STOP

■ Rewind tape => Press REW in Stop mode

■ Fast forward tape =>

■ Eject tape => Press EJECT on the remote or

STOP/EJECT on the unit

You can operate using the buttons on the unit

Press FF in Stop mode

Insert a cassette with record tab.

• The unit power comes on automatically.

1

Press CH or number keys to Select Channel.

2

• For “LINE” input, see bottom of next page.

Press SPEED to select recording

(see page 4).

speed

3

SP = Standard Play LP = Long Play SLP = Super Long Play

• Selected speed is displayed.

Press REC to start recording.

• To edit out unwanted portions, press

4

PAUSE/SLOW to pause and resume recording.

• You cannot view another channel during recording.

■ Stop => Press STOP

■ One Touch Recording (OTR)

Press REC repeatedly to set the recording

Normal Rec

length (30 min - 4 hours).

• The unit stops recording at a preset time.

• PROG TIMER indicator lights on the unit.

Notes

• After the unit has been in Rec Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head.

• The remaining recording time of an OTR can be displayed by pressing DISPLAY.

EJECT

DISPLAY

NUMBER Keys

PLAY

ACTION

STOP

REC

REW

DISPLAY

TAPE

COUNTER

RESET

ACTION

POWER

POSITION

R-TUNE

MUTE

STOP

REC

EJECT NITE

VOL

REW/

SLEEP

3

1

2

5

4

8

7

100

0

C H

SELECT

VOL

C H

PLAY

W

PAUSE/SLO

ADD/DLT

SEARCH

PROG

FF/

CM/ZERO

SPEEDFM/TV

TRACKING

6

9

TRACKING

ADD/DLT

0:30 1:00

SELECT/SET

:CH UP

:CH DOWN :VOL UP :VOL DOWN

FF

SPEED

1:302:003:004:00

12

PAUSE/ SLOW

Copy Your Tapes (Dubbing)

Connections you’ll need to make.

Playing (Source) VCR

AUDIO

OUT

IN

VIDEO

IN FROM ANT.

OUT TO TV

Playback (Source)

Insert pre-

1

recorded tape.

2

Press PLAY then

3

(Perform operation of steps 4 and 5 on both units at same time.)

PAUSE at starting

point to put in Standby mode.

Recording (Editing) unit

VIDEO IN

AUDIO IN

Recording (Editing) unit

Insert blank tape with record tab.

• Dubbing tapes protected with Copy Guard will have poor quality results.

Select “LINE” mode.

See “Selecting Input Mode” below.

Press REC, then PAUSE/SLOW

immediately to put in Standby mode.

Basic Operation

Press PLAY

4

5

Caution

• Unauthorized exchanging

and/or copying of copyrighted recordings may be copyright infringement.

STOP

to start dubbing.

Press STOP

to stop dubbing.

Press PAUSE/SLOW

to start dubbing.

Press STOP

to stop dubbing.

Selecting Input Mode

Method 1: Press CH

Method 2: a Press ACTION for MAIN MENU. b Press

ACTION for SET UP TV screen.

c Press

then press

d Press ACTION twice to exit this mode.

. The display will change as follows.

to select “TV”, then press

to select “INPUT SELECT,” and

to select “TUNER” or “LINE.”

1

3

2

(CABLE)

(TV)

or

125LINE

69

13

TV Operation

VIDEO IN AUDIO IN

POWER VOL CH

STOP/EJECT REW/

PLAY/REPEAT

FF/ REC TIMER/FM

ACTION

REC ON TIMER

PROG TIMER

Press POWER on the remote or unit.

1

Use CH or

0 8

number keys to

A

2

3

24

NIGHT (NITE) Mode

Colour and picture intensity levels are adjusted so the screen is easier on your eyes during night time use.

N I GHT

BC

select a channel.

Press VOL + or VOL

to adjust volume.

Press NITE to set NIGHT mode.

• NIGHT mode may be selected when watching TV or playing a tape.

Ready Check List

All connections are made. Your unit is plugged in.

-

VOL + / VOL

POWER VOL CH

VIDEO IN AUDIO IN

POWER

CH

STOP/EJECT REW/

-

FF/ REC TIMER/FM

PLAY/REPEAT

ACTION

PROG TIMER

REC ON TIMER

PHONES Jack

Press NITE to cancel.

• Previous settings are restored.

• NIGHT mode is cancelled when power is turned off or power failure occurs.

■ Using the 100 key

When selecting CABLE channels 100 to 125 with the number keys, first press the 100 key, and then enter the remaining two digits.

■ Rapid Tune

Press R-TUNE to display the last channel you were watching.

■ Audio Mute

Press MUTE to instantly mute the sound. Press again to restore the previous sound level.

■ Phones

Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack.

14

CA

Closed Caption System

CA

MODE

:

CAP C1

MODE

:

OFF

Closed Caption is ...

This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes useful information from TV stations available to everyone.

Closed Caption Mode Feature

Press ACTION

to display MAIN MENU.

1

M A I N MENU

2

3

4

TEXT C2

T V

C H

SELECT : SET : ACT I ON

LOCK

CA

PTPT I ON N

I NPUT V I DEO ADJUST F

M ANTENNA : EXT

CT :

SELE SET

:

END

: ACT I ON

CACAPTPT I ON MODE

CC ON MUTE

SELECT : SET : END

: ACT I ON

OFF

CLOC

SET

SELECT

CAPT I ON

CAP C2

LANGUAGE

VCR

K

UP TV

: TUNER

:

CAP C1

Press ACTION three times to return to the normal screen.

5

Recording and Playing Back a Closed Caption/Text Program Record : Record normally. Closed Caption/

Playback : Start playback. Do above steps to

Text signal, if present, is recorded automatically.

select desired caption mode.

1)Press to select “TV.”

2)Press ACTION

EX I T

to display SET UP TV screen.

1) Press select “

2) Press to display CAPTION screen.

1) Press

CAP C1

select CAPTION MODE.

2) Press

repeatedly to select mode.

TEXT C1

(See left.)

to

CAPTION

to

Caption On Mute Feature

Closed Caption narration, if available, is displayed when MUTE button is pressed for silence.

Press ACTION

to display MAIN MENU.

1

M A I N MENU

2

3

”.

4

T V

C H

SELECT : SET : ACT I ON

LOCK

CA

PTPT I ON N

I NPUT V I DEO ADJUST F

M ANTENNA : EXT

CT :

SELE SET

:

END

: ACT I ON

CACAPTPT I ON MODE

CC ON MUTE

SELECT : SET : END

: ACT I ON

CLOC

SET

SELECT

CAPT I ON

VCR

K

UP TV

: TUNER

:

LANGUAGE

5

CAP C1

NO

CAP C2

Press ACTION three times to return to the normal screen.

6

Press MUTE to mute the sound and display closed captioning.

7

• To cancel, press MUTE again.

1) Press to select “TV.”

2) Press ACTION

EX I T

to display SET UP TV screen.

1) Press

2) Press to

1) Press to

OFF

CAP C1

select CAPTION

MODE

2) Press

repeatedly to select “OFF.”

1) Press to

select CC ON MUTE.

2) Press

repeatedly to select desired mode.

• Each press of will

change the display as shown at left.

• The caption may

broadcast over CAP C1 or C2.

select “CAPTION”.

display CAPTION screen.

.

Closed Caption Mode Selections

Caption Mode: CAP C1 or C2

A narration of selected TV programs is displayed. Check TV program listings for CC (Closed Caption) broadcasts.

Caption Mode: TEXT C1 or C2

The lower half of the screen will be blocked out. When the TV station broadcasts information, such as program listings, it will appear in this space.

Caption Mode: OFF

Closed Caption /Text narration will not be displayed. NOTE : The closed caption or text signal may be broadcast over C1, C2, or both.

Also, text contents can vary so you may wish to try different settings.

to

be

15

TV Timer Features

ALARM

AM CH

VIDEO IN

AUDIO IN

POWER

VOLCHCH

REW/

REC

ON TIMER

PROG TIMER

ON-TIMER with Alarm

This unit can be set to automatically power on in one of 3 modes (TV, Playback, or FM radio.) You can also combine the On-Timer with a one minute alarm that gradually increases in volume.

Press PROG

to display SET PROGRAM screen.

1

SET PROGRAM

2

3

T I MER PR

ON TIMER

SELECT : SET : END

: PROG

6

ALARM : O

SESELE CT H

SELECT : SET : END

: PROG

OGRAMMING

O

N T I MER

:--

AM CH

N

OUOUR

--

• ON-TIMER mode selection order

CH02CH

CH01

FM9

4

FM8

O

N T I MER

6:00AM

ALARM : O

N

SELE CT

ALARM

C

ANCEL : ADD / DLT SELECT : SET : END

: PROG

03

CH

CH125

FM1

08

ABC

When “ON” is selected,

an alarm will gradually increase in volume for one minute or until cancelled by pressing any button (including VOL + -).

To Make Corrections,

use

and to move back and correct.

1)Press to select “ON TIMER.”

2)Press to display ON TIMER screen.

1) Press desired settings.

2) Press

to set the ON-TIMER TIME or ON-TIMER mode.

• Make sure a tape is inserted if Playback mode is selected.

• See “FM Radio” on page

PLAY

19 for instructions on how to preset FM stations.

Press to select ALARM “ON” or “OFF.”

to select

Ready Check List

The clock is set to correct time.

TIMER/FM

FF/

REW/

STOP/EJECT

VOL

POWER

VIDEO IN

AUDIO IN

CH

PLAY/REPEAT

ACTION

REC

PROG TIMER

REC

ON TIMER

ON TIMER Indicator

Press PROG

to set ON TIMER.

5

• “ON TIMER SET” is displayed.

• ON TIMER Indicator lights up on the unit.

To Cancel ON-TIMER set,

Repeat steps 1 and 2. Then, press ADD/DLT to clear the time in step 3. Now, press PROG to end. “ON TIMER END” briefly appears on-screen.

Note

If no button on the remote or unit (including a button used to turn off the alarm) is pressed within 60 minutes after unit turns itself on, it will turn itself off.

16

SLEEP TIMER

This unit can be set for auto power off.

Press SLEEP repeatedly to set SLEEP TIMER.

• Pressing DISPLAY with sleep timer set displays remaining time.

Press SLEEP repeatedly until “SLEEP TIMER 00” appears to cancel.

SLEEP TIMER 30

SLEEP TIMER 60

SLEEP TIMER 90

SLEEP TIMER 00

INSTANT ALARM

You can set a timer alarm up to 60 minutes. Useful when you are cooking, etc.

Press TIMER/FM on the unit to display the instant alarm CANCEL/SET screen.

1

1:00

(one minute)

2:00

one-minute

3:00

increase until 10:00

9:00

10:00

15:00

20:00

25:00

30:00

40:00

50:00

60:00 (Max)

five-minute increase until 30:00

ten-minute increase until 60:00

Note

While timer function is in progress, you can change channels on the unit with CH SET” screen is not displayed.

while “CANCEL/

5 : 20

PM

2

CANCEL : ADD SET : CH

• Pressing TIMER/FM repeatedly on the unit

To cancel, press TIMER/FM then press ADD/DLT on

the remote while CANCEL/SET screen is displayed. To increase timer in progress, repeat step 2. Time

will be rounded up to the next 1, 5, or 10 minute interval. (See chart left.)

• If current time remaining is 12:15, countdown will restart from 15:00.

• If current time remaining is 9:15, countdown will restart from 10:00.

/

DLT 02 :

KEY ON UN I T

Remaining Time

will change display as follows.

Press CH on the

unit with CANCEL/SET screen displayed to set alarm.

the order shown left.)

00

(Time changes in

Alarm will sound at 0: 00. Press any button to stop

3

• The volume of the alarm gradually increases for one minute and then continues to beep until any button is pressed.

17

Picture Adjustment

ST

OR

NOR

AL

Press ACTION

to display MAIN MENU.

1

2

3

4

M A I N MENU

VCR

T V

CLOC

SET

UP TV

SELECT

: TUNER

ADJUST

CT :

OR

E

M

AL

: ACT I ON

E

M

AL

:

: ACT I ON

K

C H

SELECT : SET : ACT I ON

LOCK CA

PT I ON I NPUT

V I DEO

F

M ANTENNA : EXT

SELE SET

:

END

: ACT I ON

COCOL

T I NT B

R I GHTNESS P I CTUR SHARPNESS NOR

SELECT : ADJUST : END

COLOR T I NT B

R I GHTNESS P I CTUR SHARPNESS

NOR

SELECT : SET END

LANGUAGE

1)Press to select “TV.”

2)Press ACTION to

EX I T

display SET UP TV screen.

1)Press to select VIDEO ADJUST.

2)Press screen.

1)Press to select an adjustment item. (See below right.)

2)Press

To Reset Picture Controls. Press

select and set “NORMAL.” All controls return to their factory settings.

Press ACTION three times to exit.

5

18

to display

to adjust.

and to

Picture Adjustment

■ COLOUR Control

Adjust colour intensity.

■ TINT Control

Adjust for natural flesh tones.

■ BRIGHTNESS Control

Adjust picture brightness.

■ PICTURE Control

Adjust picture intensity by adjusting both contrast and colour level in the proper balance.

■ SHARPNESS Control

Adjust picture sharpness.

FM Radio

ANTENNA

POWER

VOLCHCH

REW/

FF/

REC

ON TIMER

PROG TIMER

FM Radio is ...

This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz. You can even set the On-Timer (page 16) to wake up to your favourite radio station.

FM Radio Setup

Press FM/TV on the remote or press TIMER/FM twice on the unit

1

to display FM radio mode.

1 2 : 0 0PM

2

3

FM 1 87. 5MHz

1 2 : 0 0PM

FM

1 8 7. 7MHz

MEMORY : PUSH ADD / DLT KEY

1 2 : 0 0PM

FM

1 8 7. 7MHz

MEMOR I ZED

To Make Corrections,

select station with a number key, then do step

3 again. To exit FM mode, press

FM/TV on the remote or TIMER/FM twice on the unit.

Press a number key (1~9) to select

the FM preset number.

1) Press CH to select the desired radio station.

press changes frequency by 200 KHz.)

(Each

2) Press ADD/DLT to set the radio station.

Hold down CH or

for a few seconds, then release to quickly scan for FM stations in your area.

• To cancel, press CH

or while in

search mode.

SET

UP TV

LOCK

PT I ON

CA

3

V I DEO ADJUST

F

M ANTENNA

CT :

SELE SET END

: : ACT I ON

■ For cable TV users ➔ “INT”

■ For antenna users ➔ “EXT”

: I

1) Press to

NT

2) Press to

select FM ANTENNA.

select

“INT (INTERNAL)” or “EXT (EXTERNAL)”

whichever produces better sound quality.

Press ACTION twice to end setup.

4

Using FM Radio

Press FM/TV on the remote or press TIMER/FM twice on the unit

1

to display FM radio mode.

1 2 : 0 0PM

2

FM 1 87. 5MHz

To cancel, press FM/TV on the remote or TIMER/FM twice on the unit.

Press a number key (1~9) to select

a preset FM number

(see steps 2 and

3 on this page).

FM ANTENNA Setup

Make sure FM tuning is done

VOL

POWER

VIDEO IN

AUDIO IN

TIMER/FM

FF/

REW/

STOP/EJECT

REC

PLAY/REPEAT

PROG TIMER

REC

ACTION

ON TIMER

correctly (see FM Radio Setup).

Press ACTION

to display MAIN MENU.

1

M A

I N

M

EN

2

SELECT : SET : ACT I ON

VCR

T V

CLOC

K

C H

U

LANGUAGE

EX I T

1) Press to select “TV.”

2) Press ACTION to display SET UP TV screen.

Notes

• FM radio cannot be recorded on a Video cassette.

• You may get better reception by repositioning the unit.

• You cannot select FM Radio mode during playback or record, or while a blue back screen (PROG, ACTION, MENU) is displayed.

• Once stations are set, the selected station and current time are displayed when FM Radio mode is entered. To remove time, press DISPLAY. If DISPLAY is pressed again, the unit status screen appears.

TIMER/FM

19

Timer Recording

START

F

VIDEO IN AUDIO IN

POWER VOL CH

STOP/EJECT REW/

PLAY/REPEAT

FF/ REC TIMER/FM

ACTION

REC ON TIMER

PROG TIMER

You can set up to 8 programs to be recorded while you are away.

Press PROG to display SET PROGRAM screen.

1

SET PROGRAM

2

3

T I MER PR

OGRAMMING

ON TIMER

SELECT :

: PROG

--:--

START

CT :

OPC

--:-- --

DATE

SET : END

DATE START ST

7

F

R I

TODA

Y

- - - - - - - - -- - - - - - - -- - - - - - -

SELE CT

SELE SET

: : PROG / ACT I ON

END

Example

Today’s Date

SELECT / Selection Order

7

WEEKLY

(SAT)

Repeat step 3 to set:

• start time, stop time

• Channel (or LINE for outside source)

• Speed (SP, LP, SLP)

1) Press

TIMER PROGRAMMING

2) Press to display

.

screen

• If a program is already in memory, press , and

to select an unused

program number.

Press to select

H

and or to set the recording DATE.

SLP

• 1~31 = One time

• DAILY = MON~FRI

• WEEKLY SUN~SAT = Same time once a week

2

31

WEEKLY

(MON)

1

68 9

WEEKLY

(SUN)

to select

DAILY

Ready Check List

All connections are made. Your unit is plugged in. The clock is set to correct time. The tape is long enough. The record tab is in place.

.

POWER VOL CH

STOP/EJECT REW/

FF/ REC TIMER/FM

PLAY/REPEAT

PROG TIMER

VIDEO IN AUDIO IN

ACTION

REC ON TIMER

PROGRAM TIMER indicator

Timer Recording Using

Unit Buttons

You can set a Timer Recording using ACTION key on the unit. (See page 11.)

4

P DT START

1

2 3 -- -- : -4 -- -- : --

STOP CH

day

9 : 00 p 12 : 00a 08 SP

-- -- : --

-- : -- --

CANCEL : ADD / DLT SELECT

1 - 8 E END

:

NTER

:

: PROG / ACT I ON

Press PROG (or

SPD

ACTION) to end the

--

program.

--

To Enter More Programs, press

and

to select

to set a blank program number, and then repeat step 3.

VOL CH

STOP/EJECT REW/

ACTION

Press STOP/EJECT and REW together without a tape inserted to display MAIN MENU.

Press + - to select “VCR” and STOP/EJECT and REW

Press PROG twice (or ACTION) to exit this mode.

5

• If you’re using a cable box, make sure that it is tuned to the desired channel and the power is left on for timer recording.

• PROG TIMER indicator lights on the unit.

together to display SET UP VCR screen.

Press to select “TIMER PROGRAM” and + to display the TIMER PROGRAM screen.

Repeat main steps 3 ~ 5.

20

day

9

SP

SAT

P

08

START

Cancel a Timer Recording:

-- --

--

(Recording is in progress)

Hold down STOP for a few seconds to cancel the Timer Recording.

• Any future daily or weekly recordings will be performed as programmed.

Review, Replace or Clear Program Contents : (Recording is not in progress)

Repeat steps 1 and 2 on page 20.

1 2

P DT START

1 day

2 3 4

STOP CH

9

:

0000p 1212 :

0000a

1 - 8

:

0808

125

L

8 10 : 00a 12 : 00p 10 8 : 00p 9 : 00p 10 SU

9 : 00p 10 : 00p

CANCEL : ADD / DLT SELECT E

NTER

END

: PROG / ACT I ON

S

PD

Press to select

SP

the desired program.

SP

LP

TAPE

RESET

ACTION

POWER

DISPLAY

POSITION

COUNTER

R-TUNE

MUTE

STOP

REC

EJECT NITE

VOL

REW/

SLEEP

3

1

2

TRACKING

5

6

4

8

7

9

ADD/DLT

100

C H

SELECT

C H

PAUSE/SLO

0

SEARCH

VOL

PLAY

W

CM/ZERO

PROG

FF/

SPEEDFM/TV

ADD/DLT

SELECT/SET

:CH UP :CH DOWN :VOL UP :VOL DOWN

PROG

STOP

To Replace program...

3

DATE

S

TART

S

TOP

8

SAT

9:

0000P

TODA

Y

C

ATE

GORY : MOV I

----------------------------------------------

SESELE CT

START

SELECT : SET

:

: PROG /

END

1212: 0000A 08

E

D

ATATE

ACT I ON

CH

ABC

SP

To Clear program...

P DT START

1

2 3 4

Press PROG twice (or ACTION) to exit this mode.

4

STOP CH

-- --

:

----

---- :

1 - 8

:

---- ----

125

L

8 10 : 00p 12 : 00a 10 8 : 00p 9 : 00p 10 SU

9 : 00p 10 : 00p

SELECT E

NTER

END

: PROG / ACT I ON

S

PD

--

SP SP LP

1) Press

2) Press and press

to display.

to select

or to set new program contents.

3) Press PROG (or

ACTION).

Press ADD/DLT.

Notes

• 2 minutes before Timer recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and/ or the PROG TIMER Indicator flashes. Be sure a cassette with record tab is loaded and the unit is in Stop mode.

• If the start times of two programs overlap, the lower numbered program will have priority.

• If the start time for a Timer Recording comes up during a normal recording or One Touch Recording (page 12), the Timer Recording will not be performed.

• If there is a power interruption of more than one minute, the recording may not be performed or continued.

• If “INCOMPLETE” appears after all items have been set, check all entries and make necessary corrections.

21

Tape Operation

Search System is ...

Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are made, program index and information are also included. These index marks can be used to access or scan recordings.

Index Search

Go directly to the desired recording.

I NDEX SEARCH

ENTER I NDEX NUMBER : 1

1

US I

NG 1- 9

KEYS

FOR

W

ARD SEARCH : FF

2

REVERSE SEARCH NEXT

:

SEARCH

EX

I T :

STOP

I NDEX

:

S

EARCH 3

I NDEX

S

EARCH

I NDEX SEARCH

REW

3

FOR

W

ARD SEARCH : FF

REVERSE SEARCH

■ To calculate the Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

:

REW

Press SEARCH

in Playback or Stop mode to display INDEX SEARCH screen.

Press number keys

to select the recording number.

• To calculate number, see below.

Press FF or REW

to start search.

• Play begins at search end. To search forward or back 1 index, press FF or REW while screen left is displayed (10 seconds).

Program End Search

Locates end point of recording for continuity.

Press SEARCH twice in Playback or Stop mode to display PROGRAM END

1

SEARCH screen .

PROGRAM END SEARCH

2

SEARCH START : FF

I T :

SEARCH

EX

Example of Program End Search operation.

Fig.1

Press SEARCH button

Fig.2

Press SEARCH button

Fig.3

Program 1

End Point

Program 1

FF

Program 1

BLANK

If search exceeds a few seconds in BLANK area.

Press SEARCH button

Press FF

to start search.

PLAYBACK DIRECTION

INDEX

Program 2 or BLANK

End Point

INDEX

Program 2

FF

BLANK

FF

INDEX

BLANK

End Point

Program 2

2 34

5

617

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

175

34 62

7

NOTE: indicates start points of each recording.

Notes

• Make each entry within 10 seconds, or the Index Search mode will be cancelled.

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.

22

Upon locating end point...

The unit searches slightly past end point, reverse searches, and plays the last few seconds of the program, then stops.

Press SEARCH button

Notes

• If Program End Search is started very close to an index mark, that mark may be skipped over.

• To cancel, press PLAY or STOP.

Auto Operation Functions

VIDEO IN

AUDIO IN

POWER

VOLCHCH

REW/

REC

ON TIMER

PROG TIMER

■ Auto Shut Off

No broadcast signal in TV, blank tape is Played for 5 minutes ➔ Power turns off

• This feature is cancelled if any button is pressed during above mode.

■ Auto Playback

Insert a tape in Power off mode

➔ Power turns on

• Playback begins if tape has no record tab.

POWER

VIDEO IN

AUDIO IN

REC

PLAY/REPEAT

ACTION

PROG TIMER

REC

ON TIMER

TIMER/FM

FF/

REW/

STOP/EJECT

VOL

REW FF

■ Auto Rewind

Tape reaches its end

➔ Rewind, ➔ Stop

■ Playback Auto Eject

(Repeat Play is “OFF”)

Tape with no record tab reaches its end

➔ Rewind, ➔ Stop, ➔ Eject

Tape Position Display

To find out present tape position and amount of tape remaining.

Tape position cannot be detected for C-Cassettes, tapes under 30 minutes, and some other tapes.

Press TAPE POSITION

to detect current tape position.

1

DETECT I NG TAPE POS I T I ON

BEG I N END

Press TAPE POSITION (or wait 5 seconds) to return to normal screen.

2

• “DETECTING TAPE POSITION” is displayed only when a cassette is first inserted and it takes several seconds for correct tape position to appear.

• The present tape position

SLP

indication and amount of tape

R 120 MIN.

remaining (according to tape speed) is displayed.

• Tape remaining time display may not be precise.

Note

• This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length.

23

Tape Operation (continued)

PLAY

FF

Repeat Play

Set to see a recording over and over.

Press ACTION

to display MAIN MENU.

1

M A I N MENU

2

SELECT : SET : ACT I ON

REPEAT

3

T

I MER

T I ME STAMP

SELECT : SET END

Press ACTION twice to end setup.

4

VCR

T V

CLOC

C H

SET

UP V

PLAY

PROGRAMMING

: ON

:

: ACT I ON

LANGUAGE

K

CR

1)Press to select “VCR.”

2)Press ACTION

EX I T

: OFF

to display SET UP VCR screen.

1)Press to

select “ PLAY

2)Press

REPEAT PLAY “ON” or “OFF.”

REPEAT

.”

to set

Zero Search

To quickly return to a specific tape counter location.

Press DISPLAY during playback to display the Counter.

1

Press COUNTER

0 : 00 : 00

2

BEG I N END

RESET at the desired position to reset to “0:00:00.”

Commercial Skip

By pressing the CM/ZERO button in Playback mode you can skip over 1 to 3 minutes of recorded tape in just a few seconds.

Press CM/ZERO repeatedly to select skip time in Playback mode.

1

• No indication appears.

Repeat Play Notes

• Playback repeats when tape end is reached or unrecorded portion over 30 seconds is detected.

• During playback, you may also press PLAY/REPEAT repeatedly on the unit to select REPEAT “ON” or “OFF.”

Continue playback, rewind, or fast forward.

3

Press STOP.

4

Press CM/ZERO

1 : 23 : 45

5

BEG I N END

• : Present position mark : Zero position mark

• Unit goes into FF or REW mode and

stops at the last point the Counter was set to 0:00:00.

in stop mode to start ZERO SEARCH.

24

Zero Search Note

• If a blank portion exists on the tape, and depending on the position of the mark, the mark display may be out of position.