Panasonic PV-27DF5 User Manual

TV / DVD Combination

Operating Instructions

Model No.

PV-27DF5

• Connection and Initial Setup Procedures are on pages 10 and 13.

MULTI FORMAT PLAYBACK

*Ability to play back may depend on recording conditions.

As an ENERGY STAR® Partner, Panasonic Corporation of North America has determined that this product or product model meets the ENERGY

STAR

Please read these instructions carefully before attempting to connect, operate, or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

guidelines for energy efficiency.

LSQT0942 A

InformationGetting Started TV Operation Disc Operation Information

Before Using

Congratulations

On your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit.

Date of Purchase _____________________

Dealer Purchased From ________________

Dealer Address _______________________

Dealer Phone No. _____________________

Model No. __________________________

Serial No. ___________________________

U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

This television receiver provides display of television closed captioning.

Accessories

Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.

To order accessories, call toll free 1-800-332-5368.

1 Remote Control (EUR7724010 or EUR7724010R)

2 Batteries “AA”

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Safety Precautions/Mesures de sécurité

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOIS TURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT IN WALL SOCKET. FULLY INSERT.

AVERTISSEMENT :

AFIN DE PRÉVENIR TOUT RISQUE D’INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À UNE HUMIDITÉ EXCESSIVE.

Attention :

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

FCC WARNING :

ANY UNAUTHORIZED CHANGES OR MODIFICATIONS TO THIS EQUIPMENT WOULD VOID THE USER’S AUTHORITY TO OPERATE IT.

Getting Started

FCC NOTICE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, “Something About Interference”, available from FCC local regional offices, helpful.

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER, THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

(Inside of product)

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and main te nance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

IMPORTANT SAFEGUARDS AND PRE CAU TIONS

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.

 INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit or in this manual. If uncertain, have

your Electric Utility Service Company or Video Products Dealer verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one wide blade), or a three-wire

grounding type plug. Always hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord. Regularly remove dust, dirt, etc.

on the plug. POLARIZED PLUG CAUTION: The plug fits into outlet only one way. If it cannot be fully inserted, try reversing it. If it

still will not fit, have an electrician install the proper wall outlet. Do not tamper with the

plug. GROUNDING PLUG CAUTION: The plug requires a three-hole grounding outlet. If necessary, have an electrician

install the proper outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against electrical shock, fire or personal

 USING THE UNIT

Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safe guards.

1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,

such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,

unplug unit and have it inspected by a qualified service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for extended periods of

time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises. Immediately unplug unit, and have it

• Never drop or push any object through openings in unit. Touching internal

injury:

• Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord.

• Keep magnetic objects, such as speakers, away from unit to avoid electrical

• Do not tamper with the cord in any way.

• An extension cord should have the same type plug (polarized or grounding) and must be securely connected.

• Overloaded wall outlets or extension cords are fire hazards.

• Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during operation. If

blocked, heat build-up may result in a fire hazard or heat damage to cassettes or discs.

For your protection:

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire,

shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to gently remove dust

or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could overspray, or seep into unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

a. Never cover ventilation slots while unit is ON, or operate unit while placed on a

bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case or rack, unless properly ventilated.

5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator, in direct sunlight, inside closed

vehicles, in high temperature locations [over 95 °F (35 °C)], or in over 75 % humidity. If unit is suddenly moved from a cold place to a warm one, moisture may con dense in unit and on the disc causing damage. Never subject unit to vibration, impact, or place it so that the surface is tilted as internal parts may be seriously dam aged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• Move any appliance and cart combination with care. Quick stops, excessive force, and uneven surfaces may cause objects to overturn.

• Carefully follow all operating instructions.

 OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly grounded to provide

some protection against built up static charges and voltage. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information regarding proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, con nec tion to grounding electrodes, and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

Locate an outside antenna system well away

from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could

 SERVICE

be fatal.

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating in struc tions, the unit does not operate

properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug unit and contact a qualified service tech ni cian.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts specified by the manufacturer,

or that have equal safety char ac ter is tics as original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a thorough safety check be done as

described in the manufacturer’s service literature to ensure video unit is in safe operating condition.

inspected by a service technician to avoid potential fire and shock hazards.

parts may cause electric shock or fire hazard. Do not put any foreign object on the tray.

interference.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING C ONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

ELECTRIC SERVICE EQUIPMENT

NEC

- NATIONAL ELECTRICAL CODE

GROUND CLAMP

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Getting Started

TV Operation

Getting Started

Before Using ............................................................................................................................ 2

Safety Precautions/Mesures de sécurité .............................................................................. 3

IMPORTANT SAFEGUARDS AND PRECAUTIONS ............................................................... 4

Information ............................................................................................................................... 6

Location of Controls ............................................................................................................... 8

Connections ........................................................................................................................... 10

Tuning TV ............................................................................................................................... 13

TV Operation .......................................................................................................................... 16

MTS Broadcast / TV Stereo System ..................................................................................... 18

TV Timer Features ................................................................................................................. 19

Closed Caption System ........................................................................................................ 20

Video / Audio Setting ............................................................................................................ 22

V-Chip Control Features ....................................................................................................... 24

Display Features .................................................................................................................... 28

Disc Operation

Information

Basic Disc Operation ............................................................................................................ 29

DVD-RAM Operation .............................................................................................................. 33

Disc Operation -Using Information Screen- ........................................................................ 35

Special Disc Operation .........................................................................................................38

Settings for DVD Operation .................................................................................................. 41

Warning and Instruction Displays ....................................................................................... 45

Glossary ................................................................................................................................. 45

Before Requesting Service ................................................................................................... 46

Guía rápida de uso en español ............................................................................................ 47

Limited Warranty ................................................................................................................... 52

Customer Services Directory ............................................................................................... 53

Specifications ........................................................................................................................ 54

Index ....................................................................................................................................... 55

InformationGetting Started TV Operation Disc Operation Information

Information

Information (Unit)

Safety Precaution

The unit may tip or fall if not situated on a stable surface, if pushed, or during an earthquake. Use a strong rope or chain (not included) to fasten the unit firmly to a strong wall support.

Loading the Batteries

1 Open the cover.

2 Insert batteries as marked.

Information (Disc)

Discs that can be played

Disc type Disc Logo

DVD-Video

DVD-R*

DVD-RAM

Video CD

CD-R

Indication in these operating instructions

DVD-V

(DVD-Video)

RAM

(CD-DA)

VCD

3 Close the cover.

• Insert so the poles (+ and - ) match those in the remote control.

• Do not use rechargeable type batteries.

Do not:

• Mix old and new batteries.

• Use different types at the same time.

• Heat or expose to flame.

• Take apart or short circuit.

• Attempt to recharge alkaline or manganese batteries.

• Use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire. Remove if the remote control is not going to be used for a long period of time. Store in a cool, dark place.

DST (Daylight Saving Time)

Unit auto adjusts clock for DST (Daylight Saving Time.)

■ Spring (First Sunday in April)

DST: ON ➞ Sets clock ahead one hour.

■ Autumn (Last Sunday in October)

DST: ON ➞ Turns clock back one hour.

CD-RW

Do not use irregularly shaped discs (e.g. heart-shaped), as these can damage the unit.

*1 DVD-Video formatted discs [finalized].

Discs recorded using Version 1.1 of the Video Recording Format.

Discs that cannot be played



DVD with Region No. other than “1” or “ALL”, DVD from PAL system, DVD-ROM, DVD+R, DVD-AUDIO, DVD-RW, DVD+RW, CD-ROM, CDV, CVD, CD-G, CD-TEXT, SACD, Photo-CD.

Note:

• The digital audio content side of DualDiscs do not meet the technical specifications of the Compact Disc Digital Audio (CD-DA) format so may not play back in this unit.

• It may not be possible to play CD-R, CD-RW, DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

VCD

• If your area does not observe Daylight Saving Time, select DST : OFF (see “Manual Clock Setting” on page 14).

• Keep these time changes in mind when pro gram ming the unit for timer recording.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

 DVDs that can be played

You can play discs with these symbols.

 Playing DVDs

The producer of these discs can control how they are played so you may not always be able to control play as described in these operating instructions. Read the disc’s instructions carefully.

 DVD-R discs

Panasonic DVD-R recorded and finalized* on a Panasonic DVD video recorder are played as DVD-Video on this unit.

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

• Non-cartridge discs

Type

Capacity

• Discs that can be removed from their cartridges (TYPE 2 and 4)

• 12 cm (5″) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3″) 2.8 GB (double-sided)

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVDR playback.

• Do not attach sticker to disc. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown at right. Fin ger prints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

• Do not try to close disc tray when disc is not properly placed.

Disc tray

Getting Started

Disc

• Remove TYPE 2 and 4 discs from their cartridges before use, then return them when you are finished. Read the instructions for the disc carefully.

TYPE 2 or 4 disc

• Some parts of the disc, for example where one program ends and another begins, may not play smoothly.

Non-cartridge disc

 CD-R and CD-RW discs

This unit can play CD-R and CD-RW if they are formatted as CDDA (digital audio) and finalized*.

* A process that allows play on compatible equipment.

Region Management Information

This unit is designed and man u fac tured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not cor re spond to the Region number of this unit, this unit cannot play this disc.

For U.S.A. and Canada

• The region number of this player is “1”.

• The player will play DVD-Video marked with labels bearing “1” or “ALL”.

Example:

ALL

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

DVD-RAM, DVD-R :



Clean only with DVD-RAM disc cleaner. Never use cloths or cleaners for CDs, etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs can be damaged if stored or left in areas:

• Exposed to direct sunlight.

• That are humid or dusty.

• Near heat (i.e. heater, radiator, etc.).

Information (MAIN MENU Screen)

In the Main Menu display, only icons which can be selected appear normally while those not available appear dark.

Example: When the unit is used for the first time, the DVD icon is dark because it cannot be selected in this condition (see right). However, when DVD is pressed to enter DVD mode, the DVD icon becomes selectable.

MAIN MENU

LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

Location of Controls

Remote Control Buttons

12 13

15 16

27 28

OPEN / CLOSE Opens or closes the disc tray.

POWER Turns the unit on or off.

DISPLAY

RAPID TUNE Displays the last channel you were watching.

MUTE Mutes the sound instantly.

INPUT

ACTION Displays Main Menu.

SELECT ▲▼◄► Controls navigation around on-screen menu.

CHANNEL UP/DOWN Selects a channel.

SKIP- Ι◄◄

STOP Stops playback.

STILL

SEARCH ◄◄ /

SLOW-

AUDIO Selects the desired audio mode.

ANGLE Selects the desired angle in DVD mode.

TIMER Set ON TIMER or SLEEP TIMER.

RETURN Returns to DVD menu screen.

DVD Set to DVD mode.

Displays the TV status and clock. In DVD mode, displays disc and unit information.

Changes input source.

Skips back one chapter or track. Goes to previous menu screen.

Pauses picture in Playback mode and frame advance picture in Still mode. Activates reverse rapid scene search in Play mode. Increases reverse slow motion speed in still mode. (Up to 5 levels)

TV Sets to TV mode.

NUMBER Keys Selects a channel directly.

ADD/DELETE/

CLEAR

MENU / PLAY LIST

SET Sets selected menu.

VOLUME UP/DOWN Adjusts volume.

PLAY Begins playback.

SKIP+ ►►Ι

TITLE / D.NAVI

SEARCH ►► /

SLOW+

SURROUND / VSS Creates a deeper, 3-D sound effect.

SUB TITLE Selects a different subtitle language.

ZOOM Enlarges specific portions of DVD picture.

Adds or deletes a channel. Cancels an item on the screen.

Displays DVD menu. Displays Play List. (DVD-RAM)

Skips one chapter or track. Goes to next menu screen. Selects the desired title by number on some DVDs. Displays Direct Navigator. (DVD-RAM). Activates forward rapid scene search in Play mode. Increases forward slow motion speed in still mode. (Up to 5 levels)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Unit Buttons

Front View

Getting Started

Built In

Speakers

Phones Jack Video Input

Connector 2 Audio Input

Connector 2

Disc Tray Place compatible discs here.

POWER Turns the unit on or off. VOLUME UP/

DOWN CHANNEL

UP/DOWN

Equipped with 2 front speakers. Connect an ear phone or headphones. Connect from other component. (LINE 2) Connect from other component. (LINE 2)

Adjusts volume.

Selects a channel.

Rear View

23 6

DVD Operation

SKIP-

Skips back one chapter or track. Goes to previous menu screen.

SKIP+

STOP Stops playback.

PLAY Begins playback. OPEN/

Skips one chapter or track. Goes to next menu screen.

Opens or closes the disc tray.

789101112

ON TIMER

Indicator

Remote Sensor

13 15

Lights when the On Timer is set.

Receives infrared signal from remote control.

1 AC Power Plug

Optical digital audio output

connector Audio Output Connector

(L/R)

When plugged into an AC outlet, this unit consumes 0.9 W of electric power in OFF condition.

Outputs audio signal. (Digital)

Outputs audio signal. (Analog)

123 45 6

4 Audio Input Connector 1

5 Video Input Connector 1

VHF/UHF Antenna

Input Terminal

Connect from other component. (LINE 1)

Input terminal for an antenna or cable box signal.

Connections

Notes on con nec tions

• Turn off the power supply for all com po nents before making any connections.

• If the cables necessary for connecting a component to the system are not included with the component or available as an option, you may need to fashion a cable to suit the component concerned.

• Read the instruction manual for each system component care ful ly before connecting it.

Connecting the RF in Terminal

CAUTION

Overtightening “Nut type” RF coaxial cables may damage jacks. Finger tighten only.

 Antenna Connection

Connect the cable from the Antenna to the VHF/UHF terminal on the unit.

VHF Antenna

Mixer

UHF Antenna

Connecting the “1, 2” AV Input Terminals

Connects VCRs and other peripheral equipment

 AV Input terminal 1 is used

Audio

Video

OUT

 Cable Connection

Connect the cable supplied by your local cable company to the VHF/UHF terminal on the unit.

Cable Box

In from CABLE

Note to CABLE system installer:

This re mind er is pro vid ed to call the CABLE (Cable TV) System Installer’s at ten tion to Article 820-40 of the NEC that pro vides guide lines for proper grounding and, in par tic u lar, specifies that the cable ground shall be con nect ed to the ground ing system of the build ing, as close to the point of cable entry as practical.

Notes:

• Similar connections are available at the “1, 2” AV input terminals.

• AV Input terminal 2 is located on the front of the unit.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Connecting the Audio Output Terminal

Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on DVDs by connecting an amplifier and speakers. There are two types of connection, digital and analog.

WARNING

Don’t place the unit on amplifier or equipment that may become hot. The heat can damage the unit.

 Digital connection

Firmly connect the cable to the connector.

Getting Started

Connect an AV amplifier with Dolby Digital or DTS decoders

Enjoy “Dolby Digital” or “DTS” surround sound.

OPTICAL

Amplifier with built in Dolby Digital or DTS decoders.

Speakers (example)

Please see amplifier manual for speaker requirements.

Connect a Digital amplifier

Smart one-line connection is possible.

OPTICAL

 Analog connection

Connect an analog amplifier to enjoy high-quality stereo sound with sampling frequencies of 96 kHz.

IMPORTANT NOTE: Caution for optical digital audio output connector:

• Be sure to refer to page 43 regarding output settings of Dolby Digital, DTS, and PCM.

• CDs and Video CDs can be played as usual.

• Audio from the Digital Audio Out terminal is only output during playback.

• When connecting an amplifier which contains the Dolby Digital or DTS decoder, be sure to select “Bitstream”. When connecting an amplifier which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”. (See page 43.) Otherwise, attempting to play a DVD may cause such a high level of noise that it may harm your hearing and damage your speakers.

Notes:

• Some DTS decoders which do not support DVD-DTS Interface may not work properly with the unit.

• Avoid bending/twisting the optical digital cable when connecting.

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full

5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other U.S. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Tuning TV

EJECT

POWER

ACTION SELECT

▲▼◄►/ SET

CH ▲▼

STOP

NUMBER Keys

ADD/DLT

Case 2

If setup is incomplete, the following screen appears. Check connection of Antenna/Cable to the RF in Terminal, then try to manually set the clock as follows.

AUTO CLOCK SET

IS INCOMPLETE

PLEASE SET CLOCK BY PRESSING ACTION KEY

a. Press ACTION on the Remote Control to display

SET CLOCK Menu screen.

SET CLOCK

1/ 1/2005 SAT 12:00AM

DST:ON

SELECT: SET:SET START :ACTION

b. Press ▲▼ to select the month and press SET to

set. In the same manner, select and set the date, year, time, and DST (Daylight Saving Time).

• Press ◄ repeatedly to move the cursor. Press ▲▼ to make a correction.

SET CLOCK

10/25/2005 TUE 11:45AM

DST:ON

SELECT: SET:SET START :ACTION

TV Operation

POWER

SKIP Ι◄◄

STOP

PLAY

Initial Setup (Ready to Play)

Please make all cable or antenna connections before powering on. Plug the unit power cord into an AC wall outlet.

1 Press POWER on the Remote Control or unit. Auto

channel and clock set start.

• If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone. If you use a DSS receiver, it must be turned off.

CH AUTO SET PROCEEDING

AUTO CLOCK SET

PROCEEDING

CANCEL:STOP

• Function buttons are void during Initial Setup.

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See pages 14-15.)

c. Press ACTION twice to start CLOCK and exit.

Automatic Channel Setting

1 Press ACTION to display MAIN MENU. 2 Press ▲▼◄► to select “CH.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET to display SET UP CHANNEL screen.

SET UP CHANNEL

ANTENNA : CABLE

AUTO SET WEAK SIGNAL DISPLAY:OFF

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “ANTENNA,” then press SET to

set your antenna system (“TV” or “CABLE”).

Case 1

Settings are made automatically. When complete, this screen appears.

10/25/2005 TUE 11:45AM DST:ON SETTING : CH 10

AUTO CLOCK SET

COMPLETED

5 Press ▲▼ to select “AUTO SET,” then press SET.

Note:

• After Channel Auto Set is finished, Clock Auto Set will be performed. (If clock is set manually, Clock Auto Set will not be performed.)

Add or Delete a Chan nel

Manual Clock Setting

 To add channel:

Select channel with NUMBER keys and press ADD/DLT.

CHANNEL 08 ADDED

 To delete channel:

Select channel with CH ▲▼ or NUMBER keys and press ADD/ DLT.

CHANNEL 08 DELETED

Automatic Clock Setting

1 Press ACTION to display MAIN MENU.

2 Press ▲▼◄► to select “CLOCK.”

MAIN MENU

DVD LOCK LANGUAGE

1 Press ACTION to display MAIN MENU. 2 Press ▲▼◄► to select “CLOCK.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET to display SET CLOCK screen.

(“TIME ZONE ADJUST” appears only when auto clock is set.)

SET CLOCK

AUTO CLOCK SET

MANUAL

TIME ZONE ADJUST : 0

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “MANUAL,” then press SET.

SET CLOCK

10/25/2005 TUE 11:45AM

DST:ON

SELECT: SET:SET END :ACTION

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET to display SET CLOCK screen.

SET CLOCK

AUTO CLOCK SET

MANUAL

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “AUTO CLOCK SET,” then

press SET.

5 Press ▲▼ and press SET to select and set the

month, date, year, time, and DST (Daylight Saving Time).

To Make Corrections, repeatedly press ◄ to move

to error, then correct.

6 Press ACTION twice to start the clock and exit this

mode.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Time Zone Adjust

(Only when Auto Clock is set.)

1 Press ACTION to display MAIN MENU. 2 Press ▲▼◄► to select “CLOCK.”

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET to display SET CLOCK screen.

AUTO CLOCK SET MANUAL

TIME ZONE ADJUST : 0

MAIN MENU

SET CLOCK

Change Language Setting

1 Press ACTION to display MAIN MENU. 2 Press ▲▼◄► to select “LANGUAGE.”

SELECT: SET:SET END :ACTION

3 Press SET repeatedly.

English Spanish

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

TV Operation

French

For English

MAIN MENU

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “TIME ZONE ADJUST” and

press SET to subtract or add hour(s) as necessary.

SET CLOCK

AUTO CLOCK SET MANUAL

TIME ZONE ADJUST :+1

SELECT: SET:SET END :ACTION

5 Press ACTION twice to exit.

Note:

• If set manually time zone does not appear.

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

For Spanish

MENU PRINCIPAL

DVD BLOQUEO IDIOMA

TV RELOJ CANAL

ELEGIR: FIJAR:SET TERMINAR:ACTION

-1

For French

DVD BLOCAGE LANGUE

TELE HORLOGE CANAL

SEL.: REGLER:SET FIN :ACTION

4 Press ACTION to exit.

Reset all unit Memory Func tions

Returns to factory setting. Use if relocating unit, or if Initial Setup needs to be redone.

• Make sure a disc is not inserted in unit.

1 Turn the unit Power on.

2 Hold down both PLAY and SKIP Ι◄◄ on the unit for

more than 5 seconds.

• The power will shut off.

3 Perform “Initial Setup” on page 13.

TV Operation

RAPID TUNE

MUTE

INPUT

ACTION SELECT

▲▼◄►/ SET

CH▲▼

NUMBER keys

100 key

VOL+/-

 Method 2:

Press INPUT. The display will change as follows.

LINE1

LINE2

TUNER

 Method 3:

1 Press ACTION for MAIN MENU. 2 Press ▲▼◄► to select “TV”, then press SET for

SET UP TV screen.

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press ▲▼ to select “INPUT SELECT,” and then

press SET to select “TUNER”, “LINE 1”, or “LINE 2.”

SET UP TV

CAPTION

INPUT SELECT :TUNER

SET UP VIDEO/AUDIO DVD VOL ADJUST :+2

AV Input Terminal 2

Selecting Input Mode

 Method 1:

Press CH ▲▼. The display will change as follows.

Notes:

• The diagram at right is an example.

• TV CH 2 and CABLE CH 1 represent the lowest channels in memory, while TV CH 69 and CABLE CH 125 represent the highest channels in memory.

(TV) CH2

(CABLE)

CH1

(TV)

CH69

(CABLE)

CH125

LINE2

LINE1

SELECT: SET:SET END :ACTION

4 Press ACTION twice to exit this mode.

LINE 1:

Signal of source connected to AV Input terminal 1 is displayed. (Rear of the unit.)

LINE 2:

Signal of source connected to AV Input terminal 2 is displayed.

TUNER:

Signal of source connected to VHF/UHF terminal is displayed.

Using the CH/VOL Button

 Select desired channel:

Press CH ▲▼ or NUMBER keys.

 Adjust desired volume level:

Press VOL + or VOL -.

Using the Number and 100 keys

When selecting CABLE channels 100 to 125 with the NUMBER keys, first press the 100 key, and then enter the remaining two digits.

Example 1:

To select channel 125, first press the 100 key, then 2, then 5.

Example 2:

To select channel 12, first press the 1 key, then 2.

Example 3:

To select channel 2, first press the 0 key, then 2.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Rapid Tune

Press R-TUNE to display the last channel you were watching.

Audio Mute

Press MUTE to instantly mute the sound. Press again to restore the previous sound level.

Weak Signal Display Feature

When “ON” is selected, the picture is displayed even when a broadcast signal is weak or non-existent.

1 Press ACTION to display MAIN MENU. 2 Press ▲▼◄► to select “CH.”

3 Press SET to display SET UP CHANNEL screen.

MAIN MENU

Surround Sound System

You can hear a deeper, 3-D sound effect using just the unit’s two front speakers.

1 Press SURROUND.

•”SURROUND ON” is displayed.

To Cancel, press SURROUND.

Notes:

• Surround sound effect is not available for normal (mono) broadcasts.

• The surround effect (TV mode only) is not output to Audio Output L/R Connector.

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “WEAK SIGNAL DISPLAY.” 5 Press SET to set “ON” or “OFF.”

SET UP CHANNEL

ANTENNA : CABLE AUTO SET

WEAK SIGNAL DISPLAY:OFF

SELECT: SET:SET END :ACTION

ON:

Picture is displayed regardless of signal condition, and may not always be clearly visible.

OFF:

Screen turns solid blue when signal is absent or weak.

Note:

• If the unit is connected to equipment which has a blue screen feature, selecting “ON” will have no effect on the other equipment.

TV Operation

6 Press ACTION twice to return to the normal screen.

+ 39 hidden pages

Panasonic PV-27DF5 User Manual

Before Using

IMPORTANT SAFEGUARDS AND PRE CAU TIONS

Table of Contents

Information

Location of Controls

Connections

TV Operation