Panasonic PT-RZ970BEJ Product Data Sheet

PEC

S

Product Number : PT-RZ970B/RZ970W

ILE

F

PT-RZ970LB/RZ970LW

Product Name : DLP

™

Projectors

As of July 2016. Specifications and appearance are subject to change without noti ce.

SFD16M034

1/21

DLP™ Projector

Specications

Main unit

Power supply
Power consumption

NORMAL: 742W ECO: 617W LONG LIFE1: 410-588

LONG LIFE 2: 375-588W LONG LIFE 3: 349-588W SHUTTER: 82W

STANDBY MODE [ECO]*1: 0.2W STANDBY MODE [NORMAL]: 3W

STANDBY MODE (When the [QUICK STARTUP] function is enabled): Approx. 85 W

*Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297 ft),

ICE62087: 2008 Broadcast contents,

Picture mode: Standard, Dynamic Contrast2

BTU value

LCDpanel

Lens

Light source

Screen size

Brightness*

Center-to-corner uniformity*
Contrast*

3

3

Resolution

Scanning frequency SDI

Panel size
Display method
Pixels
PT-RZ970B/W
PT-RZ970LB/LW

HDMI/DVI-D fH: 15- 100kHz, fV: 24 - 120Hz, dot clock: 25 - 162 MHz

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

AC100 - 240V 10.4-5.0A 50Hz/60Hz
1,050W

Max 3,584 BTU

17.0 mm (0.67 in) diagonal (16:10 aspect ratio)

DLP™ chip × 1, DLP™ system

2,304,000 (1920 × 1200) × 1, total of 1,024,000 pixels
Powered zoom/focus lenses (1.7–2.4:1), F 1.7–1.9, f 25.6–35.7 mm
Optional powered zoom/focus lenses and xed-focus lens

Laser Diode Laser class 1(Class3R for US models)

Luminance life for set: 20,000 hours at half luminance (normal)/

24,000 hours at half luminance (Eco)
* Temperature: 30°C(86°F), Altitude 700m (2,297 ft), Dust: 0.15mg/m

Dynamic Contrast3

43,800 hours at constant luminance (LONG LIFE1)

61,320 hours at constant luminance (LONG LIFE2)

87,600 hours at constant luminance (LONG LIFE3)

1.27–15.24 m (50–600 inches) (16:10 aspect ratio)
*1.27 – 5.08 m (50 – 200 inches) with the ET-DLE055 (16:10 aspect ratio)
*2.54 – 7.62 m (100 – 350 inches) with the ET-DLE030 (16:10 aspect ratio)

10,000 lumens (Center)*

2

/ 9,400 lumens*

3

9,400 lumens (Half luminance) (NORMAL)

7,500 lumens (Half luminance) (ECO)

3,700 lumens (Constant luminance) (LONG LIFE1)

3,100 lumens (Constant luminance) (LONG LIFE2)

3

2,500 lumens (Constant luminance) (LONG LIFE3)

90%
10,000:1 (All White/All Black) (Dynamic Contrast3)
1920 × 1200 pixels

3G-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p,

[2K/24p], [2K/25p], [2K/30p]

3G-SDI signal (YPBPR4:2:2 10-bit):

SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p,

[2K/48p], [2K/50p], [2K/60p]

HD-SDI signal (YP

BPR4:2:2 10-bit):

SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p,

1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,

1125(1080)/24sF, 1125(1080)/30p

SD-SDI signal (YC

BCR4:2:2 10-bit):

SMPTE ST 259 compliant: 525i(480i), 625i(576i)

4

525i (480i)*

, 625i (576i)*4, 525p (480p), 625p (576p), 750 (720)/60p,
750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p,
1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p,
1125 (1080)/50p, VGA (640 x 480) - WUXGA (1920 x 1200) compatible
with non-interlaced signals only

3

As of July 2016 2/21

SFD16M034

DLP™ Projector

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Scanning frequency

Geometry correction range

RGB
YP

BPR (YCBCR)

Video/S-Video

Projection

lens Model

No.

Supplied lens/

ET-DLE170

ET-DLE030*

ET-DLE055
ET-DLE085
ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450

Only [KEYSTONE] used

Vertical

keystone

correction

angle α (°)

±40

1

+5/-0

±22
±22
±40
±40
±40
±40

fH: 15- 100kHz, fV: 24 - 120Hz, dot clock: 20 - 162 MHz
525i (480i): fH15.73 kHz; fV59.9 Hz,
625i (576i): fH15.63 kHz; fV59.9 Hz,
525p (480p): f

H 31.50 kHz; fV 60 Hz,

625p (576p): fH31.25 kHz; fV50 Hz,
750 (720)/60p: fH

45.00 kHz; fV60 Hz,
750 (720)/50p: fH37.50 kHz; fV50 Hz,
1125 (1080)/60i: fH 33.75 kHz; fV 60 Hz,
1125 (1080)/50i: fH 28.13 kHz; fV 50 Hz,
1125 (1080)/25p: f

28.13 kHz; fV25 Hz,

H

1125 (1080)/24p: fH27.00 kHz; fV24 Hz,

H

1125 (1080)/24sF: f
1125 (1080)/30p: f

27.00 kHz; fV48 Hz,

H

33.75 kHz; fV30 Hz,
1125 (1080)/60p: fH 67.50 kHz; fV 60 Hz,
1125 (1080)/50p: f

56.25 kHz; fV50 Hz

H

fH: 15.73 kHz, fV: 59.9 Hz [NTSC/NTSC4.43/PAL-M/PAL60]

H

: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

f

[KEYSTONE] and [CURVED] used together Only [CURVED] used

Horizontal

keystone

correction

angle β (°)

±15

0
±15
±15
±15
±15
±15
±15

Vertical

keystone

correction

angle α (°)

±20

―

±8

±8
±20
±20
±20
±20

Horizontal

keystone

correction

angle β (°)

±15

―

±8

±8
±15
±15
±15
±15

Min. value

of R2/L2

0.9

―

1.7

1.7

1.1

0.7

0.4

0.3

Min. value

of R3/L3

1.7

―

4.3

4.3

2.6

1.3

0.8

0.6

Min. value

of R2/L2

0.5

―

1
1

0.6

0.4

0.3

0.2

Min. value

of R3/L3

1

―

2.6

2.6

1.5

0.7

0.5

0.3

When using the optional Upgrade Kit (Model No.: ET-UK20)

Projection

lens Model

No.

Supplied lens/

ET-DLE170

ET-DLE030*

ET-DLE055
ET-DLE085
ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450

*1 Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves
away from the screen.

*2 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be
made exceeding total of 55°.

Only [KEYSTONE] used*

Vertical

keystone

correction

angle α (°)

±40

1

+5/-0

±22
±22
±40
±40
±45
±45

[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)

Screen

Horizontal

keystone

correction

angle β (°)

±40

0
±15
±15
±40
±40
±40
±40

2

[KEYSTONE] and [CURVED] used together Only [CURVED] used

Vertical

keystone

correction

angle α (°)

±20

±20
±20
±20
±20

―

±8
±8

Horizontal

keystone

correction

angle β (°)

±15

―

±8

±8
±15
±15
±15
±15

Min. value

of R2/L2

0.7

―

1.3

1.3

0.9

0.5

0.3

0.2

Min. value

Screen

of R3/L3

1.3

―

3.3

3.3
2
1

0.6

0.4

Min. value

of R2/L2

0.4

―

0.8

0.8

0.5

0.3

0.2

0.2

Min. value

of R3/L3

0.7

―

1.9

1.9

1.1

0.6

0.4

0.3

SFD16M034

3/21As of July 2016

DLP™ Projector

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Geometry correction range

Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)

Projection distance
Arc radius

Screen

Arc center

Screen

Projection distance
Arc radius

• When [GEOMETRY] is used, the focus of the entire screen may be lost as correction increases.

• Make the curved screen a circular arc shape with one part of a perfect circle removed.

• Adjustment range of the [GEOMETRY] items may not match the listed projection range depending
on the projection lens. Use this projector within the projection range, otherwise the correction may
not work.

Screen

Arc center

Screen

Optical axis shift Vertical: +50%, -16%(powered),

Horizontal: +30%, -10%(When using the ET-DLE085, +28%, -10％) (powered)

NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055.
If using the ET-DLE030, the optical axis is fixed.

Installation Ceiling/floor, front/rear, 360 degree free installation

Projection distance
Arc radius

Projection distance
Arc radius

Terminals SDI IN

HDMI IN

DVI-D IN

RGB 1 IN

R, G, B

Y,

Y,C

Video

RGB 2 IN

R, G, B

Y, PB, PR(Y, CB, CR)

SERIAL/MULTI

PROJECTOR SYNC IN

SERIAL/MULTI

PROJECTOR SYNC OUT

REMOTE 1 IN

REMOTE 1 OUT

REMOTE 2 IN D-sub 9-pin (female) x1 for external control (parallel)

LAN/DIGITAL LINK

SFD16M034

PB , PR (Y, CB, CR)

BNC × 1,

3G-SDI signal: SMPTE ST 424 compliant

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

HDMI 19-pin × 1, Deep Color, compatible with HDCP,

DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP,

for single link only

BNC ×5

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y:

1.0 Vp-p (including sync signal), P

B/PR (CB/CR): 0.7 Vp-p, 75 ohms

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

1.0Vp-p, 75 ohms

D-sub HD 15-pin (female) ×1

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms

D-sub 9-pin (female) ×1 for external control (RS-232C compliant)

D-sub 9-pin (male) x 1 for link control

M3 jack x 1 for wired remote control

M3 jack x 1 for link control (for wired remote control)

RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control)
connection, 100Base-TX, compliant with PJLink™(Class 1)
Deep Color, HDCP

4/21As of July 2016

DLP™ Projector

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Power cord length
Cabinet materials
Dimensions (W × H × D) PT-RZ970B/RZ970W

3.0 m (9 ft 10 in)
Molded plastic
498 x 200*
(19-19/32 x 7-7/8*5 x 22-7/8in ) with supplied lens

PT-RZ970LB/RZ970LW

498 x 200*
(19-19/32 x 7-7/8*

Weight PT-RZ970B/RZ970W

PT-RZ970LB/RZ970LW
Operation noise
Operating temperature
Operating humidity

Approx. 23.2kg (51.1lbs) with supplied lens
Approx. 22.4kg (49.4lbs) without lens
41 dB
0–45 °C (32–113 °F)*
10%–80% (no condensation)

Remote control unit

Power supply
Operation range

3 V DC (R03/AAA type battery × 2)
Approx. 30 m (98 ft 5 in) when operated from directly in front of the
signal receptor

Dimensions (W × H × D)

7

Weight*

48 × 145 × 27 mm (1-57/64 × 5-45/64 × 1-3/64 in)
Approx. 102 g (3.6 oz) including batteries

Supplied accessories

Power cord with secure lock (× 1) (× 2 for EU models)
Wireless/wired remote control unit (× 1)
Batteries for remote control (R03/AAA type×2)
Software CD-ROM (Logo Transfer Software, Multi Monitoring
& Control Software) (× 1)
Lens Mount Cover (× 1)
Lens cover (× 1) (Only models with lens)

Optional accessories

Digital interface box

ET-YFB100G
Digital LINK Switcher ET-YFB200G
Zoom

lens (0.8–1.0:1) ET-DLE085

Zoom

lens (1.3–1.9:1)
Zoom lens (1.7–2.4:1)
Zoom lens (2.3–3.6:1)
Zoom lens (3.6–5.4:1)
Zoom lens (5.4–8.6:1)

Fixed-focus lens (0.38:1)
Fixed-focus lens (0.8:1)
Ceiling mount bracket

ET-DLE150
ET-DLE170 (same as supplied lens)
ET-DLE250
ET-DLE350
ET-DLE450
ET-DLE030
ET-DLE055
ET-PKD120H (for high ceilings)
ET-PKD120S (for low ceilings)

High-ceiling mount bracket

ET-PKD130H

(6-axis adjustment mechanism)
Attachment for ceiling mount bracket
Geometry Manager Pro Upgrade kit
Auto Screen Adjustment Upgrade kit
Early Warning Software

ET-PKD130B
ET

-UK20
ET-CUK10
ET-SWA100*

5

x 581mm

5

x 538 mm

5

x 21-3/16in) without lens

6

* The symbol at the end of the part number will vary depending on the type of license.

*1 When the STANDBY MODE is set to Eco, network functions such as power on over the LAN will not operate.
*2 The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by
the ISO/IEC 21118:2012 international standards.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*5 with legs at shortest position.
*6 Limits the luminance when used in locations from 0m to 2,700m (0ft to 8,858ft) above sea level at ambient temperatures of 35°C (95°F) or higher,
or from 2,700m to 4,200m (8,858ft to 13,780ft) above sea level at ambient temperatures of 25°C (77°F) or higher.
*7 Average value. May differ depending on models.

SFD16M034

5/21As of July 2016

DLP™ Projector

Dimensions

580.8
(22-7/8)

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

(10-19/32)(10-19/32)

538

(21-3/16)

249 (9-13/16)

221 (8-11/16)

442 (17-13/32)

498 (19-19/32)

Terminals

1

2345

678910 11

269 269

28

115.5
(4-9/16)

unit : mm (inch)
NOTE: This illustration is not drawn to scale.

42.8

(1-3/32)

(1-11/16)

181

(7-1/8)

96.5
(3-13/16)

4

(3/4)

(5/32)

19

432 (17)

444 (15/32)

457 (18)

1 REMOTE 1 INPUT

2 REMOTE 1 OUTPUT

3 REMOTE 2 INPUT

4 SERIAL/MULTI PROJECTOR SYNC INPUT

5 SERIAL/MULTI PROJECTOR SYNC OUTPUT

6 SDI INPUT

7 RGB 1 INPUT

8 RGB 2 INPUT

9 DVI-D INPUT

10 HDMI INPUT

11 LAN/DIGITAL LINK TERMINAL

200

(7-7/8)

SFD16M034

6/21As of July 2016

DLP™ Projector

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Standard setting-up position (If using other than the ET-DLE030)

2

*

352–432

(13-27/32–17)

294244

Upper edge of projected image

EE

ø60.5

L

1

*

(11-9/16)(9-19/32)

*1 When the lens protrudes to the maximum.

2

463.5–543.5*

84 mm (3-5/16 in) with the ET-DLE085
43 mm (1-11/16 in)
with the supplied lens/ET-DLE170
44 mm (1-23/32 in) with the ET-DLE150
45 mm (1-25/32 in) with the ET-DLE250
51mm (2 in) with the ET-DLE350
95mm (3 -3/4 in) with the ET-DLE450
27 mm (1-1/16 in) with the ET-DLE055

(18-1/4–21-13/32)

*2 Adjustable in 40 mm (1-9/16 in) steps.

Lower edge of projected image

unit : mm (inch)

370

100

Projected image

100
(3-15/16)

259

(10-3/16)

(14-9/16)

(3-15/16)

NOTE:

Illustrations show the projector
installed using optional ceiling mount
bracket ET-PKD120H, optional bracket
assembly ET-PKD130B and an optional
lens.

This illustration is not drawn to scale.

Caution:

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket. Furthermore, in order to prevent it from falling

down from the ceiling, use the supplied wire on the mounting bracket.

SFD16M034

7/21As of July 2016