Panasonic PT-RZ870WU, PT-RZ870LWU, PT-RZ870LBU, PT-RZ870BU Product Sheet

TENTATIVE TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

DLP™ Projector

DLP™ Projector

Specications

Main unit

Power supply

Power consumption

BTU value

DLP™ chip

Lens

Light source

Illumination life of set

Screen size

Brightness*

Center-to-corner uniformity*
Contrast*
Resolution

Scanning frequency SDI

1

3

Panel size
Display method
Pixels

PT-RZ870B/W
PT-RZ870LB/LW

HDMI/DVI-D

3

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

For Global : AC100〜240 V 9.9〜4.5A 50 Hz/60 Hz
For Taiwan : AC110 V-240V 9.0A〜4.5A 60 Hz

950W

NORMAL: 689W ECO: 583W LONG LIFE1: 393-548W 

LONG LIFE 2: 363-548W LONG LIFE 3: 334-548W SHUTTER: 82W

STANDBY MODE [ECO]: 0.3W STANDBY MODE [NORMAL]: 3W

STANDBY MODE (When the [QUICK STARTUP] function is enabled): Approx. 85 W

*Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297 ft),

IEC62087: 2008 Broadcast contents,

Picture mode: Standard, Dynamic Contrast2

Max 3,242 BTU(Without light 3,126 BTU)

17.0 mm (0.67 in) diagonal (16:10 aspect ratio)

DLP™ chip × 1, DLP™ system

2,304,000 (1920 × 1200)

Powered zoom/focus lenses (1.7–2.4:1), F 1.7–1.9, f 25.6–35.7 mm
Optional powered zoom/focus lenses and xed-focus lens

Laser Diode Laser class 1(Class3R for US models)

Varies depending on operation mode setting.
Half brightness at 20,000 hours (NORMAL/QUIET1/QUIET2)/
Half brightness at 24,000 hours (ECO)

* Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast3

Under conditions of 0.15 mg/m3 of particulate matter
43,800 hours at constant luminance (LONG LIFE1)

61,320 hours at constant luminance (LONG LIFE2)
87,600 hours at constant luminance (LONG LIFE3)

* Temperature: 35°C (95°F), Altitude 700m (2,297 ft),Dynamic Contrast3
Under conditions of 0.15 mg/m3 of particulate matter

1.27 – 15.24 m (50 –600 inches) (16:10 aspect ratio)
*1.27 – 5.08 m (50 – 200 inches) with the ET-DLE055 (16:10 aspect ratio)
*2.54 – 8.89 m (100 – 350 inches) with the ET-DLE030 (16:10 aspect ratio)

Varies depending on operation mode setting.

8,500 lumens*

8,500 lumens (Half luminance) (NORMAL)

6,800 lumens (Half luminance) (ECO)

7,200 lumens (Half luminance) (QUIET1)

5,400 lumens (Half luminance) (QUIET2)

3,400 lumens (Constant luminance) (LONG LIFE1)

2,800 lumens (Constant luminance) (LONG LIFE2)

2,300 lumens (Constant luminance) (LONG LIFE3)

90%

10,000:1 (All White/All Black) (Dynamic Contrast3)

1920 × 1200 pixels

3G-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,
1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p,
[2K/24p], [2K/25p], [2K/30p]

3G-SDI signal (YP

SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p,
[2K/48p], [2K/50p], [2K/60p]

HD-SDI signal (YP

SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p,
1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,
1125(1080)/24sF, 1125(1080)/30p

SD-SDI signal (YC

SMPTE ST 259 compliant: 525i(480i), 625i(576i)

Moving image signal resolution: 480i*

Still image signal resolution: 640 × 400 to 1920 × 1200 (non-interlace)

Dot clock frequency: 25 MHz to 162 MHz

2

/8,800 lumens (Center)*3

BPR4:2:2 10-bit):

BPR4:2:2 10-bit):

BCR4:2:2 10-bit):

4

/576i*4 to 1920 × 1080

As of May 2018

As of July 2018 1/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

2/21

DLP™ Projector

DLP™ Projector

TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Scanning frequency

Geometry correction
range

RGB

BPR (YCBCR)

YP

Video/S-Video

Resolution: 640 × 400 to 1920 × 1200

Dot clock frequency: 162 MHz or less

PIAS (Panasonic Intelligent Auto Scanning) system

Resolution: 480i/576i to 1920 × 1080

Dot clock frequency: 148.5 MHz or less

The HD/SYNC and VD terminals do not support 3 value SYNC.

f

: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PA L60]

H

H

f

: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)

Screen

Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)

Projection distance
Arc radius

Screen

Projection distance
Arc radius

Projection

lens Model

No.

Supplied lens/

ET-DLE170

ET-DLE030*

ET-DLE055
ET-DLE060
ET-DLE085
ET-DLE105
ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450

Screen

Arc center

Only [KEYSTONE] used

Vertical

keystone

correction

angle α (°)

±40

1

+5/-0

±22
±16
±22
±22
±40
±40
±40
±40

Screen

Horizontal

keystone

correction

angle β (°)

±15

0
±15
±10
±15
±15
±15
±15
±15
±15

Screen

Arc center

Screen

Projection distance
Arc radius

[KEYSTONE] and [CURVED] used together Only [CURVED] used

Vertical

keystone

correction

angle α (°)

±20

±20
±20
±20
±20

―

±8

―

±8
±8

Horizontal

keystone

correction

angle β (°)

±15

―

±8

―

±8

±8
±15
±15
±15
±15

Min. value

of R2/L2

0.9

―

1.7

―

1.7

1.7

1.1

0.7

0.4

0.3

Min. value

of R3/L3

1.7

―

4.3

―

4.3

4.3

2.6

1.3

0.8

0.6

Projection distance
Arc radius

Min. value

of R2/L2

0.5

―

1

―

1
1

0.6

0.4

0.3

0.2

Min. value

of R3/L3

1

―

2.6

―

2.6

2.6

1.5

0.7

0.5

0.3

As of May 2018

As of July 2018 2/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

3/21

DLP™ Projector

DLP™ Projector

TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Geometry correction
range

Optical axis shift

When using the optional Upgrade Kit (Model No.: ET-UK20)

Projection

lens Model

No.

Supplied lens/

ET-DLE170

ET-DLE030*

ET-DLE055
ET-DLE060
ET-DLE085
ET-DLE105
ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450

*1 Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves
away from the screen.

*2 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be
made exceeding total of 55°.

• When [GEOMETRY] is used, the focus of the entire screen may be lost as correction increases.

• Make the curved screen a circular arc shape with one part of a perfect circle removed.

• Adjustment range of the [GEOMETRY] items may not match the listed projection range depending
on the projection lens. Use this projector within the projection range, otherwise the correction may
not work.

1

Vertical: +50%, -16%(powered)
(When using the ET-DLE060, +40%, -16％)
Horizontal: +30%, -10%(powered)
(When using the ET-DLE060, +19%, -10％)
(When using the ET-DLE085/ET-DLE105, +28%, -10％)

NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055.
If using the ET-DLE030, the optical axis is fixed.

Installation Ceiling/floor, front/rear

Terminals SDI IN

HDMI IN

DVI-D IN

RGB 1 IN

R, G, B

B, PR (Y, CB, CR

Y,

P

Y,C

Video

RGB 2 IN

R, G, B

Y, P

B, PR(Y, CB, CR)

SERIAL/MULTI PROJECTOR
SYNC IN

SERIAL/MULTI PROJECTOR
SYNC OUT

REMOTE 1 IN

REMOTE 1 OUT

REMOTE 2 IN D-sub 9-pin (female) ×1 for external control (parallel)

DIGITAL LINK/LAN

2

Only [KEYSTONE] used

Vertical

keystone

correction

angle α (°)

±40

+5/-0

±22
±16
±22
±22
±40
±40
±45
±45

Horizontal

keystone

correction

angle β (°)

±40

0
±15
±10
±15
±15
±40
±40
±40
±40

*

[KEYSTONE] and [CURVED] used together Only [CURVED] used

Vertical

keystone

correction

angle α (°)

±20

±20
±20
±20
±20

―

±8

―

±8
±8

Horizontal

keystone

correction

angle β (°)

±15

―

±8

―

±8

±8
±15
±15
±15
±15

Min. value

of R2/L2

0.7

―

1.3

―

1.3

1.3

0.9

0.5

0.3

0.2

Min. value

of R3/L3

1.3

―

3.3

―

3.3

3.3
2
1

0.6

0.4

Min. value

BNC × 1,

3G-SDI signal: SMPTE ST 424 compliant

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

HDMI 19-pin × 1, Deep Color, compatible with HDCP,

DVI-D 24-pin × 1, DVI 1.0 compliant, compatible with HDCP,
for single link only

BNC ×5

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y:

1.0 Vp-p (including sync signal), P

)

B/PR (CB/CR): 0.7 Vp-p, 75 ohms

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

1.0Vp-p, 75 ohms

D-sub HD 15-pin (female) ×1

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y: 1.0 Vp-p (including sync signal), P

B/PR(CB/CR): 0.7 Vp-p, 75 ohms

D-sub 9-pin (female) ×1 for external control (RS-232C compliant)

D-sub 9-pin (male) × 1 for link control

M3 jack × 1 for wired remote control

M3 jack × 1 for link control (for wired remote control)

RJ-45 × 1 for network and DIGITAL LINK (video/network/serial control)
connection, 100Base-TX, compliant with PJLink™(Class 1)
Deep Color, HDCP

of R2/L2

0.4

―

0.8

―

0.8

0.8

0.5

0.3

0.2

0.2

Min. value

of R3/L3

0.7

―

1.9

―

1.9

1.9

1.1

0.6

0.4

0.3

As of May 2018

As of July 2018 3/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

4/21

DLP™ Projector

DLP™ Projector

TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

Power cord length

Cabinet materials

Dimensions

PT-RZ870B/RZ870W

(W × H × D)

PT-RZ870LB/RZ870LW

Weight PT-RZ870B/RZ870W

PT-RZ870LB/RZ870LW
Operation noise
Operating temperature

Operating humidity

Remote control unit

Power supply
Operation range

Dimensions (W × H × D)

7

Weight*

Other Applications

Supplied

accessories

3.0 m (9 ft 10 in)

Molded plastic

5

498 x 200*
(19-19/32 x 7-7/8*

498 x 200*
(19-19/32 x 7-7/8*

x 581mm

5

x 22-7/8in ) with supplied lens

5

x 538 mm

5

x 21-3/16in) without lens

Approx. 23.2kg (51.1lbs) with supplied lens

Approx. 22.4kg (49.4lbs) without lens
41dB (37dB[QUIET1] / 35dB[QUIET2])
0–45 °C (32–113 °F)*

6

10%–80% (no condensation)

3 V DC (AAA/R03/LR03 battery × 2)
Approx. 30 m (98 ft 5 in) when operated from directly in front of the
signal receptor

48 × 145 × 27 mm (1-7/8 × 5-23/32 × 1-1/16 in)
Approx. 102 g (3.6 ozs.) including batteries

Multi Monitoring and Control Software (for Windows)

Logo Transfer Software (for Windows)

Geometry Manager Pro (for Windows)

Power cord with secure lock (× 1) (× 2 for Europe / ASIA models)

Wireless/wired remote control unit (× 1)

Batteries for remote control (R03/AAA type ×2)

CD-ROM (Operating Instructions) (× 1)

Lens Mount Cover (× 1)

Lens cover (× 1) (Only models with lens)

Optional accessories

Digital interface box

ET-YFB100G
Digital LINK Switcher ET-YFB200G
Zoom lens ࠉ
Zoom

lens ET-DLE085

ET-DLE060

Zoom lens ET-DLE105
Zoom

lens
Zoom lens
Zoom lens
Zoom lens
Zoom lens

Fixed-focus lens
Fixed-focus lens
Ceiling mount bracket

ET-DLE150
ET-DLE170 (same as supplied lens)
ET-DLE250
ET-DLE350
ET-DLE450
ET-DLE030/ET-DLE035*

8

ET-DLE055
ET-PKD120H (for high ceilings)
ET-PKD120S (for low ceilings)

High-ceiling mount bracket

ET-PKD130H

(6-axis adjustment mechanism)
Attachment for ceiling mount bracket
Geometry Manager Pro Upgrade kit
Auto Screen Adjustment Upgrade kit
Early Warning Software ET-SWA100*

*1 Value is for the supplied standard zoom lens. The value varies depending on the lens.
*2 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2012 international standards.
*3 The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by
the ISO/IEC 21118:2012 international standards.
*4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*5 with legs at shortest position.
*6 Limits the luminance when used in locations from 0m to 2,700m (0ft to 8,858ft) above sea level at ambient temperatures of 30°C (86°F) or higher,
or from 2,700m to 4,200m (8,858ft to 13,780ft) above sea level at ambient temperatures of 25°C (77°F) or higher.
*7 Average value. Weight varies for each product.

8 It will be released from November, 2018

*

9The symbol at the end of the part number will vary depending on the type of license.

*

ET-PKD130B
ET

-UK20

ET-CUK10/CUK10P

9

As of May 2018

As of July 2018 4/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

5/21

DLP™ Projector

DLP™ Projector

Dimensions

580.8
(22-7/8)

TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

(10-19/32)(10-19/32)

538

(21-3/16)

249 (9-13/16)

221 (8-11/16)

442 (17-13/32)

498 (19-19/32)

Terminals

1

2345

678910 11

269 269

28

115.5
(4-9/16)

unit : mm (inch)
NOTE: This illustration is not drawn to scale.

42.8

(1-3/32)

(1-11/16)

180

(7-3/32)

95.5
(3-3/4)

432 (17)

444 (15/32)

457 (18)

20

(25/32)

4

(5/32)

1 REMOTE 1 INPUT

2 REMOTE 1 OUTPUT

3 REMOTE 2 INPUT

4 SERIAL/MULTI PROJECTOR SYNC INPUT

5 SERIAL/MULTI PROJECTOR SYNC OUTPUT

6 SDI INPUT

7 RGB 1 INPUT

8 RGB 2 INPUT

9 DVI-D INPUT

10 HDMI INPUT

11 DIGITAL LINK/LAN TERMINAL

200

(7-7/8)

As of May 2018

As of July 2018 5/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

6/21

TENTATIVE TENTATIVE

PT-RZ870B/RZ870W/RZ870LB/RZ870LW

DLP™ Projector

DLP™ Projector

Standard setting-up position (If using other than the ET-DLE030)

Upper edge of projected image

EE

PT-RZ970B/RZ970W/RZ970LB/RZ970LW

*1 When the lens protrudes to the maximum.

2

2

ø60.5

L

1

*

(11-9/16)(9-19/32)

*

352–432

(13-27/32–17)

463.5–543.5*

294244

104 mm (4-3/32 in) with the ET-DLE060
84 mm (3-5/16 in) with the ET-DLE085
88 mm (3-15/32 in) with the ET-DLE105
44 mm (1-23/32 in) with the ET-DLE150
43 mm (1-11/16 in)
with the supplied lens/ET-DLE170
45 mm (1-25/32 in) with the ET-DLE250
51mm (2 in) with the ET-DLE350
95 mm (3-3/4 in) with the ET-DLE450

(18-1/4–21-13/32)

27 mm (1-1/16 in) with the ET-DLE055

*2 Adjustable in 40 mm (1-9/16 in) steps.

Lower edge of projected image

Projected image

100
(3-15/16)

259

(10-3/16)

100

(3-15/16)

370

(14-9/16)

NOTE:

Illustrations show the projector
installed using optional ceiling mount
bracket ET-PKD120H, optional bracket
assembly ET-PKD130B and an optional
lens.

This illustration is not drawn to scale.

unit : mm (inch)

Caution:

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket. Furthermore, in order to prevent it from falling
down from the ceiling, use the supplied wire on the mounting bracket.

As of May 2018

As of July 2018 6/20

RZ870G_SYF_01_11/07/2018

SFD16M034-3

7/21