Panasonic PT-RZ790BEJ User Manual

Operating Instructions

Functional Manual

DLP™ Projector

Model No.

Commercial Use

PT-RZ990 PT-RZ890 PT-RZ790 PT-RZ690

Thank you for purchasing this Panasonic product.

■This manual is common to all the models regardless of sufxes of the Model No.

zfor Taiwan

B: Black model, the standard zoom lens supplied

zfor India

BD: Black model, the standard zoom lens supplied LBD: Black model, the lens sold separately

zfor Korea

B: Black model, the standard zoom lens supplied W: White model, the standard zoom lens supplied

zfor other countries or regions

B: Black model, the standard zoom lens supplied LB: Black model, the lens sold separately W: White model, the standard zoom lens supplied LW: White model, the lens sold separately

■Before operating this product, please read the instructions carefully and save this manual for future use.

■Before using this product, be sure to read “Read this rst!” (x pages 5 to 17).

ENGLISH

DPQP1335ZB/X1

Contents

Read this rst! 5

Chapter 1 Preparation

Precautions for use 21

Intended use of the product 21 Cautions when transporting 21 Cautions when installing 21

Security 24 DIGITAL LINK 25 Art-Net 25 Application software supported by the projector 25 Storing 25

Disposal 26 Cautions on use 26 Accessories 27 Optional accessories 28

About your projector 29

Remote control 29 Projector body 31

Preparing the remote control 34

Inserting and removing the batteries 34

When using the multiple projectors 34 Connecting the remote control to the projector

with a cable 34

Chapter 2 Getting Started

Setting up 36

Usable outlet 36 Installation mode 36

Parts for installation (optional) 38 Projected image and throw distance 38 Adjusting adjustable feet 47

Removing/attaching the projection lens 48

Removing the projection lens 48 Attaching the projection lens 49

Connecting 50

Before connecting 50

Connecting example: AV equipment 50 Connecting example: Computers 51 Connecting example using DIGITAL LINK 52 Connecting example when using the

contrast synchronization function/shutter synchronization function 53

Chapter 3 Basic Operations

Switching on/off the projector 56

Connecting the power cord 56

Power indicator 57 Switching on the projector 58 When the initial setting screen is displayed 59 When the administrator account setting screen

is displayed 65

Making adjustments and selections 67 Switching off the projector 68

Projecting 69

Selecting the input signal 69 Adjusting the focus, zoom, and lens shift 70 Adjusting the focus balance 71 Setting the lens type 72 Moving the projection lens to the home position 72

Lens shift range 73

Operating with the remote control 75

Using the shutter function 75 Using the on-screen display function 75 Using the automatic setup function 76 Using the function button 76 Displaying internal test pattern 76 Using the status function 77 Setting ID number of the remote control 77

Chapter 4 Settings

Menu navigation 79

Navigating through the menu 79 Main menu 80 Sub-menu 81

[PICTURE] menu 84

[PICTURE MODE] 84 [CONTRAST] 84 [BRIGHTNESS] 84 [COLOR] 85 [TINT] 85 [COLOR TEMPERATURE] 85 [WHITE GAIN] 87 [GAMMA] 87 [SYSTEM DAYLIGHT VIEW] 88 [SHARPNESS] 88 [NOISE REDUCTION] 89 [DYNAMIC CONTRAST] 89 [SYSTEM SELECTOR] 90 [DEFAULT PICTURE MODE] 91 sRGB-compliant video 91

[POSITION] menu 93

[SHIFT] 93 [ASPECT] 93 [ZOOM] 94 [CLOCK PHASE] 95

2 - ENGLISH

Contents

[GEOMETRY] 95

[ADVANCED MENU] menu 101

[DIGITAL CINEMA REALITY] 101 [BLANKING] 101 [INPUT RESOLUTION] 102 [CLAMP POSITION] 102 [EDGE BLENDING] 102 [FRAME RESPONSE] 104 [RASTER POSITION] 105

[DISPLAY LANGUAGE] menu 106

Changing the display language 106

[DISPLAY OPTION] menu 107

[COLOR MATCHING] 107 [COLOR CORRECTION] 108 [SCREEN SETTING] 108 [AUTO SIGNAL] 109 [AUTO SETUP] 109 [BACKUP INPUT SETTING] 110 [RGB IN] 112 [DVI-D IN] 113 [HDMI IN] 115 [DIGITAL LINK IN] 116 [SDI IN] 118 [ON-SCREEN DISPLAY] 119 [MENU MODE] 121 [IMAGE ROTATION] 121 [BACK COLOR] 122 [STARTUP LOGO] 122 [UNIFORMITY] 122 [SHUTTER SETTING] 123 [FREEZE] 125 [WAVEFORM MONITOR] 125 [CUT OFF] 126

[PROJECTOR SETUP] menu 127

[PROJECTOR ID] 127 [PROJECTION METHOD] 127 [LENS] 128 [OPERATION SETTING] 129 [LIGHT OUTPUT] 134 [BRIGHTNESS CONTROL] 134 [STANDBY MODE] 139 [QUICK STARTUP] 139 [NO SIGNAL SETTING] 139 [INITIAL STARTUP] 143 [STARTUP INPUT SELECT] 144 [DATE AND TIME] 144 [SCHEDULE] 145 [MULTI PROJECTOR SYNC] 147 [RS-232C] 149 [REMOTE2 MODE] 151 [FUNCTION BUTTON] 151 [STATUS] 151

[DATA CLONING] 153 [SAVE ALL USER DATA] 155 [LOAD ALL USER DATA] 155 [INITIALIZE] 155 [SERVICE PASSWORD] 156

[TEST PATTERN] menu 157

[TEST PATTERN] 157

[SIGNAL LIST] menu 158

Registering new signals 158 Renaming the registered signal 158 Deleting the registered signal 158 Protecting the registered signal 159

Expanding signal lock-in range 159 Sub memory 160

[SECURITY] menu 161

[SECURITY PASSWORD] 161 [SECURITY PASSWORD CHANGE] 161 [DISPLAY SETTING] 161 [TEXT CHANGE] 162 [CONTROL DEVICE SETUP] 162 [CONTROL DEVICE PASSWORD CHANGE] 163

[NETWORK] menu 165

[ETHERNET TYPE] 165 [DIGITAL LINK] 165 [WIRED LAN] 167 [PROJECTOR NAME] 167 [NETWORK STATUS] 168 [ADMINISTRATOR ACCOUNT] 168 [NETWORK CONTROL] 170 [PJLink] 171 [Art-Net] 172

Chapter 5 Operations

Network connection 176

Connecting to the network 176

Web control function 179

Computer that can be used for setting 179 Accessing from the web browser 179

Updating the rmware 197

Updating the rmware via LAN 197

Chapter 6 Maintenance

Light source/temperature indicators 203

When an indicator lights up 203

Maintenance 205

Before maintaining the projector 205 Maintenance 205

Troubleshooting 206

[SELF TEST] indications 208

ENGLISH - 3

Contents

Chapter 7 Appendix

Technical information 211

Using the PJLink function 211

Using Art-Net function 212 Control commands via LAN 216 <SERIAL/MULTI PROJECTOR SYNC

IN>/<SERIAL/MULTI PROJECTOR SYNC

OUT> terminals 219 <REMOTE 2 IN> terminal 223 <RGB 2 IN> terminal 224

Upgrade Kit 224 List of compatible signals 225

Specications 232

Dimensions 235

Precautions for attaching the Ceiling Mount

Bracket 236

Index 238

4 - ENGLISH

Read this rst!

WARNING:

This device is not intended for use in the direct eld of view at visual display workplaces. To avoid

The equipment is not intended for used at a video workstation in compliance BildscharbV.

The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.

WARNING:

1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.

2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied

service personnel.

3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing-

type mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you are

unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug.

WARNING:

This equipment is compliant with Class A of CISPR32. In a residential environment this equipment may cause radio interference.

THIS APPARATUS MUST BE EARTHED.

To prevent damage which may result in re or shock hazard, do not expose this appliance to rain

or moisture.

incommoding reexions at visual display workplaces this device must not be placed in the direct eld of view.

(for Taiwan)

WARNING:

This equipment complies with the Class A standard of CNS13438. This is Class A information technology equipment that may cause radio frequency interference when used in a residential environment, in which the user will be required to take certain appropriate countermeasures.

CAUTION:

This is a device to project images onto a screen, etc., and is not intended for use as indoor lighting in a

domestic environment.

WARNING:

To assure continued compliance, follow the attached installation instructions. This includes using

the provided power cord and shielded interface cables when connecting to computer or peripheral

devices. Also, any unauthorized changes or modications to this equipment could void the user’s

authority to operate this device.

Directive 2009/125/EC

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

ENGLISH - 5

Read this rst!

WARNING:

RISK OF ELECTRIC SHOCK. DON’T OPEN

Indicated on the projector

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the

product.

Do not look at the light emitted from the lens while the projector is being used. As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.

Indicated on the projector

Notice on laser

(for USA and Canada)

This projector is the Class 3R laser product that complies with IEC 60825-1:2007.

For North America “Complies with 21 CFR Parts 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.50 dated June 24.2007” IEC 60825-1:2007 LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT WAVE LENGTH:448-462nm MAXIMUM OUTPUT:248mW PULSE DURATION:1.1ms IEC 60825-1:2007 RAYONNEMENT LASER EXPOSITION DIRECTE DANGEREUSE POUR LES YEUX

LASER DE CLASSE 3R

APPAREIL

LONGUEURS D'ONDES:448-462nm MAXIMALE DU RAYONNEMENT:248mW DUR

E DE L'IMPULSION:1.1ms

(Inside of product)

6 - ENGLISH

Read this rst!

(for Taiwan)

This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.

(for India)

This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.

第 1 類雷射產品

(for other countries or regions)

This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.

CAUTION:

Use of controls or adjustments or performance of procedures other than those specied herein may result in hazardous radiation exposure.

CAUTION (North/Middle/South America/Taiwan)

Power Supply:

CAUTION:

This Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current only.

The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V. If you need to use higher voltages than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, re may result.

ENGLISH - 7

Read this rst!

CAUTION (North/Middle/South America/Taiwan)

This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only t a grounding-type

power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.

Do not remove

WARNING (USA and Canada)

fNot for use in a computer room as dened in the Standard for the Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

fFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the

building installation wiring.

fFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

NOTIFICATION (Canada)

This class A digital apparatus complies with Canadian ICES-003.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling

may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

8 - ENGLISH

Read this rst!

FCC NOTICE (USA)

Supplier’s Declaration of Conformity

Model Number: PT-RZ990B / PT-RZ990W / PT-RZ990LB / PT-RZ990LW

PT-RZ890B / PT-RZ890W / PT-RZ890LB / PT-RZ890LW PT-RZ790B / PT-RZ790W / PT-RZ790LB / PT-RZ790LW PT-RZ690B / PT-RZ690W / PT-RZ690LB / PT-RZ690LW

Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: Two Riverfront Plaza, Newark, NJ 07102-5490 General Contact: http://www.panasonic.com/support Projector Contact: https://panasonic.net/cns/projector/

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Warning:

To assure continued compliance, follow the attached installation instructions. This includes using the provided

power cord and shielded interface cables when connecting to computer or peripheral devices. Also, any unauthorized changes or modications to this equipment could void the user’s authority to operate this device.

ENGLISH - 9

Read this rst!

IMPORTANT: THE MOLDED PLUG

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a molded three pin mains plug for your safety and convenience. A 13 amp fuse is tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you

lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorized Service Center.

If the tted molded plug is unsuitable for the mains socket in your home, then the fuse should be

removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be tted, please observe the wiring code as shown below. If in any doubt, please consult a qualied electrician.

WARNING:

IMPORTANT:

As the colors of the wire in the mains lead of this appliance may not correspond with the colored markings

identifying the terminals in your plug, proceed as follows.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

THIS APPLIANCE MUST BE EARTHED.

The wires in this mains lead are colored in accordance with the following code:

Green - and - Yellow: Earth Blue: Neutral

Brown: Live

The wire which is colored GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or colored GREEN or GREEN - AND -

YELLOW.

The wire which is colored BLUE must be connected to the terminal in the plug which is marked

with the letter N or colored BLACK.

The wire which is colored BROWN must be connected to the terminal in the plug which is marked

with the letter L or colored RED.

Importer’s name and address within the European Union

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

10 - ENGLISH

Read this rst!

rHazard distance (IEC 62471-5:2015)

The distance from the projection lens surface, at which the level of exposure has reached the level of the applicable Exposure Limit Value, is known as the hazard distance (HD) or safety distance.

Do not look into the projected light from inside the hazard distance (within RG3 range). The eyes may be damaged by the direct irradiation. It is considered to be safe to look into the projected light from outside the hazard distance (within RG2 range).

RG2

RG3

RG2

RG3

Except ET-DLE035

rRisk group

The combination of the projector and the projection lens is categorized as the risk group 2 when the hazard distance is less than 1 m (39-3/8"). It is categorized as the risk group 3 when the hazard distance exceeds 1 m (39-3/8"), and it will be for professional use instead of consumer use.

In case of risk group 3, there is a possibility of damaging the eyes by direct irradiation when looking into the

projection light from inside the hazard distance (within RG3 range).

In case of risk group 2, it can be used safely without damaging the eyes in any condition.

The combination of the projector and the projection lens which the hazard distance exceeds 1 m (39-3/8") and is

categorized as risk group 3 is as follows.

Projection lens Model No. Risk group

ET-DLE250

ET-DLE350

ET-DLE450

Risk group 3

*1 When the projector is used with the optional Zoom Lens (Model No.: ET-DLE250, ET-DLE350, ET-DLE450) attached, the

hazard distance exceeds 1 m (39-3/8"), and regardless of the use condition, the throw ratio is larger than 2.2:1. In this case, it is

categorized as the risk group 3.

THISPROJECTORMAYBECOMERG3FORPROFESSIONALUSE ONLYANDISNOTINTENDEDFORCONSUMERUSEWHENAN INTERCHANGEABLEPROJECTIONLENSISUSEDUNDERTHE CONDITIONTHATTHROWRATIOISGREATERTHAN2.2. REFERTOTHEOPERATINGINSTRUCTIONSORLEAFLET FORHAZARDDISTANCEBEFOREOPERATION.

CEPROJECTEURPEUTDEVENIRRG3POURUNEUTILISATION

PROJECTIONINTERCHANGEABLEESTUTILISÉÀCONDITIONQUE LERAPPORTDEPROJECTIONSOITSUPÉRIEURÀ2,2.

PRENEZCONNAISSANCEDELADISTANCEDURISQUEAVANTDE

DIESERPROJEKTORKANNALSRG3NURFÜRDIEPROFESSIONELLE VERWENDUNGEINGESTUFTWERDENUNDISTNICHTFÜRDIE VERWENDUNGDURCHVERBRAUCHERKONZIPIERT,WENNEIN AUSTAUSCHPROJEKTIONSOBJEKTIVVERWENDETWIRD,UNTER DERVORAUSSETZUNG,DASSDASPROJEKTIONSVERHÄLTNIS ÜBER2,2LIEGT. BEACHTENSIEVORDERBEDIENUNGDIEBEDIENUNGSANLEITUNG UNDDASFALTBLATTINBEZUGAUFDENGEFÄHRDUNGSABSTAND.

ДАННЫЙ ПРОЕКТОР МОЖЕТ ВХОДИТЬ В ГРУППУ РИСКА RG3 — ТОЛЬКО ДЛЯ ПРОФЕССИОНАЛЬНОГО ИСПОЛЬЗОВАНИЯ, И ОН НЕ ПРЕДНАЗНАЧЕН ДЛЯ ИСПОЛЬЗОВАНИЯ ПОТРЕБИТЕЛЯМИ ПРИ ИСПОЛЬЗОВАНИИ СМЕННЫХ ПРОЕКЦИОННЫХ ОБЪЕКТИВОВ ПРИ УСЛОВИИ, ЧТО ПРОЕКЦИОННОЕ ОТНОШЕНИЕ (THROW RATIO) БОЛЬШЕ ЧЕМ 2,2. ПЕРЕД НАЧАЛОМ РАБОТЫ ОБРАТИТЕСЬ К ИНСТРУКЦИЯМ ПО ЭКСПЛУАТАЦИИ ИЛИ БРОШЮРЕ, ЧТОБЫ УЗНАТЬ ПРО ОПАСНОЕ РАССТОЯНИЕ.

이 프로젝터는 투사 비율이 2.2보다 큰 교체식 투사 렌즈를 사용한 경우, 전문가 전용인 RG3 등급이 될 수 있으며, 일반 소비자용이 아닙니다. 작동하기 전에 위험 거리에 대해서는 사용 설명서 또는 안내책자를 참조하십시오.

本投影機使用可換式投影鏡頭，且投射率大於

適合專業使用的操作前請先參閱使用說明書了解危險距離。

RG3級產品，不能用作

2.2

時，屬於僅

消費類電子產品。

DPQT1477ZA

ENGLISH - 11

Read this rst!

Each dimension inside the hazard distance (within RG3 range) for combination with projection lens which the hazard distance exceeds 1 m (39-3/8") is as follows.

(Unit: m)

Projection lens

Model No.

ET-DLE250 1.4 0.40 0.27 0.52 0.39

ET-DLE350 2.2 0.40 0.27 0.52 0.39

ET-DLE450 3.2 0.40 0.27 0.51 0.38

*1 HD: Hazard Distance *2 The values of D1 to D4 will change in accordance with the lens shift amount. Each value in the table is the maximum value.

Note

fThe value in the table is based on IEC 62471-5:2015.

12 - ENGLISH

Read this rst!

WARNING:

rPOWER

The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible

when problems occur. If the following problems occur, cut off the power supply immediately.

Continued use of the projector in these conditions will result in re or electric shock, or will cause visual

impairment.

fIf foreign objects or water get inside the projector, cut off the power supply. fIf the projector is dropped or the cabinet is broken, cut off the power supply. fIf you notice smoke, strange smells or noise coming from the projector, cut off the power supply.

Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.

During a thunderstorm, do not touch the projector or the cable.

Electric shocks can result.

Do not do anything that might damage the power cord or the power plug.

If the power cord is used while damaged, electric shocks, short-circuits or re will result.

fDo not damage the power cord, make any modications to it, place it near any hot objects, bend it

excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

Do not use anything other than the provided power cord.

Failure to observe this will result in electric shocks or re. Please note that if you do not use the provided power

cord to ground the device on the side of the outlet, this may result in electric shocks.

Completely insert the power plug into the wall outlet and the power connector into the projector terminal.

If the plug is not inserted correctly, electric shocks or overheating will result.

fDo not use plugs which are damaged or wall outlets which are coming loose from the wall.

Do not handle the power plug and power connector with wet hands.

Failure to observe this will result in electric shocks.

Use an outlet supporting 15 A independently.

Using an outlet together with another device may result in res due to heat generation.

Do not overload the wall outlet.

If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.

Clean the power plug regularly to prevent it from becoming covered in dust.

Failure to observe this will cause a re.

fIf dust builds up on the power plug, the resulting humidity can damage the insulation. fIf not using the projector for an extended period of time, pull the power plug out from the wall outlet.

Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.

rON USE/INSTALLATION

Do not place the projector on soft materials such as carpets or sponge mats.

Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam.

Using the projector under such conditions will result in re, electric shocks or deterioration of components. Oil may also distort the plastic and the projector could fall such as when mounted on the ceiling.

Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is sloped or unstable.

Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage

could result.

Do not install the projector in a location where people pass through.

People may bump into the projector or trip on the power cord, which may result in re, electric shock, or injury.

Do not cover the intake/exhaust vents or place anything within 500 mm (19-11/16") of them.

Doing so will cause the projector to overheat, which can cause re or damage to the projector.

fDo not place the projector in narrow, badly ventilated places. fDo not place the projector on cloth or papers, as these materials could be drawn into the intake vent.

ENGLISH - 13

Read this rst!

WARNING:

Do not look at or place your skin into the light emitted from the lens while the projector is being used.

Do not enter the projection luminous ux using an optical device (such as magnier or mirror).

Doing so can cause burns or loss of sight.

fStrong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light. fBe especially careful not to let young children look into the lens. In addition, turn off the power and switch

off the main power when you are away from the projector.

Do not project an image with the lens cover attached.

Doing so can cause re.

Never attempt to remodel or disassemble the projector.

High voltages can cause re or electric shocks.

fFor any inspection, adjustment and repair work, please contact an Authorized Service Center.

Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow

the projector to get wet.

Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the projector.

fDo not place containers of liquid or metal objects near the projector. fIf liquid enters inside of the projector, consult your dealer. fParticular attention must be paid to children.

Use the ceiling mount bracket specied by Panasonic.

Using the ceiling mount bracket other than the specied one will result in falling accidents.

fAttach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.

Installation work such as mounting the projector on the ceiling should only be carried out by a qualied

technician.

If installation is not carried out and secured correctly, it can cause injury or accidents, such as electric shocks.

rACCESSORIES

Do not use or handle the batteries improperly, and refer to the following.

Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.

fDo not use unspecied batteries. fDo not charge dry cell batteries. fDo not disassemble dry cell batteries. fDo not heat the batteries or place them into water or re. fDo not allow the + and – terminals of the batteries to come into contact with metallic objects such as

necklaces or hairpins. fDo not store or carry batteries together with metallic objects. fStore the batteries in a plastic bag and keep them away from metallic objects. fMake sure the polarities (+ and –) are correct when inserting the batteries. fDo not use a new battery together with an old battery or mix different types of batteries. fDo not use batteries with the outer cover peeling away or removed.

If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.

fBattery uid on your skin or clothing could result in skin inammation or injury.

Rinse with clean water and seek medical advice immediately. fBattery uid coming in contact with your eyes could result in loss of sight.

In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.

Do not allow children to reach the batteries.

Accidentally swallowing them can cause physical harm.

fIf swallowed, seek medical advice immediately.

Remove the depleted batteries from the remote control promptly.

fLeaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.

14 - ENGLISH

Read this rst!

CAUTION:

rPOWER

When disconnecting the power cord, be sure to hold the power plug and power connector.

If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks

will result.

When not using the projector for an extended period of time, disconnect the power plug from the wall

outlet.

Failure to do so may result in re or electric shock.

Before replacing the projection lens, be sure to turn off the power and disconnect the power plug from

the wall outlet.

fUnexpected projection of light may cause injury to eyes. fReplacing the projection lens without removing the power plug may result in electric shock.

Disconnect the power plug from the wall outlet before carrying out any cleaning.

Failure to do so may result in electric shock.

rON USE/INSTALLATION

Do not place heavy objects on top of the projector.

Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.

Do not put your weight on this projector.

You could fall or the projector could break, and injury will result.

fBe especially careful not to let young children stand or sit on the projector.

Do not place the projector in extremely hot locations.

Doing so will cause the outer casing or internal components to deteriorate, or result in re.

fTake particular care in locations exposed to direct sunlight or near heaters.

Do not place your hands in the openings beside the optical lens, while shifting the lens.

Failure to observe this could cause injury.

Do not install the projector in a location where salt pollution or corrosive gas may occur.

Doing so may result in falling due to corrosion. Also, it may result in malfunctions.

Do not stand in front of the lens while the projector is being used.

Doing so can cause damage and burns to clothing.

fStrong light is emitted from the projector’s lens.

Do not place objects in front of the lens while the projector is being used. Do not block the projection by placing an object in front of the projection lens.

Doing so can cause re, damage to an object, or malfunction of the projector.

fStrong light is emitted from the projector’s lens.

The projector must be carried or installed by two or more people.

Failure to do so may cause falling accidents.

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to

occur.

When mounting the projector on the ceiling, keep mounting screws and power cord from contact with

metal parts inside the ceiling.

Contact with metal parts inside the ceiling can cause electric shocks.

ENGLISH - 15

Read this rst!

CAUTION:

rACCESSORIES

When not using the projector for an extended period of time, remove the batteries from the remote

control.

Failure to observe this will cause the batteries to leak, overheat, catch re or explode, which may result in re or

contamination of surrounding area.

rMAINTENANCE

Ask your dealer about cleaning inside the projector every 20 000 hours of usage as an estimated duration.

Continuous use while dust is accumulated inside the projector may result in re.

fFor cleaning fee, ask your dealer.

To remove the battery

Remote Control Battery

1. Press the guide and lift the cover.

(ii)

(i)

2. Remove the batteries.

16 - ENGLISH

Read this rst!

Brazil Only

Brasil Apenas

rManuseio de baterias usadas

BRASIL

Após o uso, as pilhas e/ou baterias deverão

ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada.

Cobrir os terminais positivo (+) e negativo (-) com uma ta isolante adesiva, antes de depositar numa caixa

destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper

a blindagem e produzir fogo. (Fig. 1)

Fig. 1 Como isolar os terminais

Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem car expostas a temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos

terminais provocado internamente.

Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso haja irritação, consulte um médico.

Fita Isolante

rRemoção das baterias

1. Pressione a guia e levante a tampa.

(ii)

(i)

2. Remova as baterias.

ENGLISH - 17

rTrademarks

fSOLID SHINE is a trademark of Panasonic Corporation. fWindows, Internet Explorer, and Microsoft Edge are registered trademarks or trademarks of Microsoft

Corporation in the United States and other countries.

fMac, macOS, and Safari are trademarks of Apple Inc., registered in the United States and other countries. fIOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. fAndroid and Google Chrome are trademarks of Google LLC. fTrademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other

countries and areas. fDLP and the DLP logo are registered trademarks or trademarks of Texas Instruments. fThe terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

fCrestron Connected, the Crestron Connected logo, Crestron Fusion, Crestron RoomView, and RoomView

are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other

countries. fHDBaseTTM is a trademark of HDBaseT Alliance. fArt-NetTM Designed by and Copyright Artistic Licence Holdings Ltd fAdobe, Acrobat, Flash Player, and Reader are either registered trademarks or trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

fSome of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by

Ricoh Company, Ltd. fAll other names, company names, and product names mentioned in this manual are trademarks or registered

trademarks of their respective owners.

Please note that the ® and TM symbols are not specied in this manual.

Software information regarding this product

This product incorporates the following software:

(1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0), (4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.1), and/or (5) open source software other than the software licensed under the GPL V2.0 and/or LGPL V2.1. The software categorized as (3) - (5) are distributed in the hope that it will be useful, but WITHOUT ANY

WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please refer to the license terms and conditions of each open source software. The open source software license is stored in the rmware of this product and can be downloaded by accessing the projector using a web browser. For details, please refer to “Web control function” (x page 179).

At least three (3) years from delivery of this product, Panasonic will give to any third party who contacts us at

the contact information provided below, for a charge no more than our cost of physically performing source code

distribution, a complete machine-readable copy of the corresponding source code covered under GPL V2.0, LGPL V2.1 or the other licenses with the obligation to do so, as well as the respective copyright notice thereof.

Contact Information:

oss-cd-request@gg.jp.panasonic.com

rIllustrations in this manual

fIllustrations of the projector, menu screen (OSD), and other parts may vary from the actual product. fIllustrations displayed on the computer screen may differ depending on the computer type and its operating

system. fIllustrations of the projector with the power cord attached are only examples. The shape of the supplied power

cords varies depending on the country where you purchased the product.

rReference pages

fReference pages in this manual are indicated as (x page 00).

rTerm

fIn this manual, the “Wireless/wired remote control unit” accessory is referred to as “Remote control”.

18 - ENGLISH

Features of the Projector

High luminance and high contrast

▶With a unique optical system which uses

a new-generation laser light source, and the laser light source drive system, high luminance of 9 400 lm of 10 000:1*3 are achieved even with its

compact size. This projector also supports

input of 4K video signals.

*1 When [PICTURE MODE] is set to [DYNAMIC] and

[OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL]

*2 PT-RZ990: 9 400 lm

PT-RZ890: 8 500 lm PT-RZ790: 7 000 lm PT-RZ690: 6 000 lm

*3 When [PICTURE MODE] is set to [DYNAMIC], [OPERATING

MODE] in [OPERATION SETTING] is set to [NORMAL] and [DYNAMIC CONTRAST] is set to [3]

*1*2

and high contrast

Quick Steps

For details, refer to the corresponding pages.

1. Set up the projector. (x page 36)

2. Attach the projection lens. (x page 48)

3. Connect with external devices. (x page 50)

4. Connect the power cord. (x page 56)

Easy and highly exible setup

▶Easy and exible setup is achieved by

compatibility with DIGITAL LINK and Art-Net, standard support of 3G-SDI, standard support of geometric adjustment

function, 360° installation support including horizontal, vertical, and portrait utilizing the characteristics of solid-state light source, and a lineup of various optional lenses.

Long life and high reliability

▶The maintenance cost for long-term

operation is reduced by the unique light

source cooling control technology and

improvement of the dust resistance. Also,

it will contribute to the stable operation by implementation of the backup function that

will continue the projection by switching to

the backup input signal immediately even when the input signal is discontinued, in addition to adopting solid-state light source which has long life.

5. Switch on the projector. (x page 58)

6. Make initial settings. (x page 59)

fTake this step when you switch on the

power for the rst time after purchasing the projector.

7. Select the input signal. (x page 69)

8. Adjust the image. (x page 70)

ENGLISH - 19

Chapter 1

This chapter describes things you need to know or check before using the projector.

Preparation

20 - ENGLISH

Chapter 1 Preparation — Precautions for use

Precautions for use

Intended use of the product

The purpose of the projector is to project a video signal from imaging equipment or a computer on a screen or

other surface as a still image or moving image.

Cautions when transporting

fIf you purchased the projector with the standard zoom lens, remove the lens protection material before use, and

store it for the future use. Move the lens position to the home position and attach the lens protection material

when transporting.

If you purchased the projector with the lens sold separately, remove the lens hole cover before use, and store it for the future use. Move the lens position to the home position, remove the projection lens, and attach the lens

hole cover when transporting.

For the steps to move the lens position to the home position, refer to “Moving the projection lens to the home position” (x page 72).

Lens hole cover

Lens protection material

fTransport the projector with two or more people. Failure to do so may drop the projector, which may result in

damage or deformation of the projector, or injury.

fHold the bottom of the projector and do not hold the projection lens or the opening around the projection

lens when transporting. Failure to do so may cause damage. Also, handle the projector in a way not to apply excessive vibration or shock. Failure to do so may cause a failure due to the damaged internal components.

fDo not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

Cautions when installing

rAfter attaching the projection lens, be sure to attach the Lens Mount Cover.

Not doing so may cause failure due to accumulating dust internally.

rDo not set up the projector outdoors.

The projector is designed for indoor use only.

rDo not set up the projector in the following locations.

fPlaces where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal

components or malfunction.

fLocation close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to

do so may shorten the life of the components and result in malfunction.

fNear the exhaust of an air conditioner: Depending on the conditions of use, the screen may uctuate in rare

cases due to the heated air from the exhaust vent or the hot or cooled air from the air conditioner. Make sure that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.

fPlaces with sharp temperature uctuations such as near lights (studio lamps): Doing so may shorten the life of

the light source, or result in deformation of the projector due to heat, which may cause malfunctions. Follow the operating environment temperature of the projector.

fNear high-voltage power lines or near motors: Doing so may interfere with the operation of the projector. fPlaces where there is high-power laser equipment: Directing a laser beam onto the projection lens surface

causes damage to the DLP chips.

ENGLISH - 21

Chapter 1 Preparation — Precautions for use

rAsk a qualied technician or your dealer for the installation work such as installing to

a ceiling, etc.

To ensure projector performance and safety, ask a qualied technician or your dealer when installing to a ceiling or

in a high place.

rAsk a qualied technician or your dealer to install the cable wiring for DIGITAL LINK

connection.

Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate

installation.

rThe projector may not work properly due to strong radio wave from the broadcast

station or the radio.

If there is any facility or equipment which outputs strong radio waves near the installation location, install the projector at a location sufciently far from the source of the radio waves. Or, wrap the LAN cable connected to the <DIGITAL LINK/LAN> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.

rFocus adjustment

The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power.

It is recommended to perform the focus adjustment after 30 minutes have elapsed with the focus test pattern displayed. For details of the test pattern, refer to “[TEST PATTERN] menu” (x page 157).

rDo not install the projector at an altitude of 4 200 m (13 780') or higher above sea level.

rDo not use the projector in a location that the ambient temperature exceeds 45 °C

(113 °F).

Using the projector in a location that the altitude is too high or the ambient temperature is too high may reduce the

life of the components or result in malfunctions.

rProjection in all 360° direction is possible.

360°

360° vertically 360° horizontally 360° tilted

360°

(combination of vertical and horizontal)

360°

22 - ENGLISH

Chapter 1 Preparation — Precautions for use

rCautions when setting up the projector

fThe projector can be used by installing its top placed on the oor. To prevent the top surface from getting

scratched during use, it is recommended to attach about a 20 mm (25/32") square buffer material (such as

rubber cushion) on the four corners of the top surface.

Buffer material

Floor

Buffer material

fUse the adjustable feet only for the oor standing installation and for adjusting the angle. Using them for other

purposes may damage the projector.

fWhen installing the projector with a method other than the oor installation using the adjustable feet, top placed

on the oor, or the ceiling installation with the Ceiling Mount Bracket, use the ve screw holes for ceiling mount (as shown in the gure) to x the projector to the mount.

In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector bottom and the setting surface by inserting spacers (metallic) between them.

fUse a torque screwdriver or Allen torque wrench to tighten the xing screws to their specied tightening torques.

Do not use electric screwdrivers or impact screwdrivers.

(Screw diameter: M6, tapping depth inside the projector: 12 mm (15/32"), torque: 4 ± 0.5 N·m)

Screw holes for ceiling mount (M6)

Adjustable feet Adjustable feet

Positions of screw holes for ceiling mount and adjustable feet

ENGLISH - 23

Chapter 1 Preparation — Precautions for use

fDo not stack projectors on top of each other. fDo not block the intake/exhaust vents of the projector. fPrevent hot and cool air from the air conditioning system to blow directly to the intake/exhaust vents of the

projector.

500 mm (19-11/16") or longer 500 mm (19-11/16") or longer

500 mm (19-11/16") or longer

100 mm (3-15/16") or longer

fDo not install the projector in a conned space.

When installing the projector in a conned space, provide air conditioning or ventilation separately. Exhaust heat may accumulate when the ventilation is not enough, triggering the protection circuit of the projector.

fPanasonic takes no responsibility for any damage to the product caused by an inappropriate choice of location

for installing the projector, even if the warranty period of the product has not expired.

Security

When using this product, take safety measures against the following incidents.

fPersonal information being leaked via this product fUnauthorized operation of this product by a malicious third party fInterfering or stopping of this product by a malicious third party

Take sufcient security measures.

fMake your password difcult to guess as much as possible. fChange your password periodically. fPanasonic Corporation or its afliate companies will never ask for your password directly. Do not divulge your

password in case you receive such inquiries.

fThe connecting network must be secured by a rewall, etc.

24 - ENGLISH

Chapter 1 Preparation — Precautions for use

DIGITAL LINK

“DIGITAL LINK” is a technology to transmit the video, audio, Ethernet, and serial control signals using a twisted pair cable by adding unique functions by Panasonic to the HDBaseTTM communication standard formulated by HDBaseT Alliance.

This projector supports the optional Panasonic DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) and peripheral devices by other manufacturers (twisted-pair-cable transmitters such as the “XTP transmitter” of Extron Electronics) that use the same HDBaseTTM standard. For the devices of other manufacturers that the operation has been veried with this projector, visit the Panasonic website (https://panasonic.net/cns/ projector/). Note that the verication for devices of other manufacturers has been made for the items set by Panasonic Corporation, and not all the operations have been veried. For operation or performance problems caused by the devices of other manufacturers, contact the respective manufacturers. This projector does not support audio transmission because it is not equipped with audio function.

Art-Net

“Art-Net” is an Ethernet communication protocol based on the TCP/IP protocol. By using the DMX controller and the application software, illumination and stage system can be controlled. Art-Net

is made based on DMX512 communication protocol.

Application software supported by the projector

The projector supports following application software. For details or downloading application software other than the “Geometric & Setup Management Software, visit the Panasonic website (https://panasonic.net/cns/projector/).

fLogo Transfer Software

This application software transfers the original image, such as company logo, which is projected at the start, to the projector.

fSmart Projector Control

This application software sets and adjusts the projector connected via LAN using a smartphone or a tablet.

fMulti Monitoring & Control Software

This application software monitors and controls the multiple display devices (projector and at panel display)

connected to an intranet.

fEarly Warning Software

This plug-in software monitors the status of the display devices and their peripherals within an intranet, and

noties of abnormality of such equipment and detects the signs of possible abnormality. “Early Warning Software” is preinstalled in the “Multi Monitoring & Control Software”. To use the early warning function of this plug-in software, install “Multi Monitoring & Control Software” in the PC to be used. By enabling the early warning function, it will notify of the approximate time to replace the consumables for the display devices,

to clean each part of the display devices, and to replace the components of the display devices, allowing to

execute maintenance in advance. The early warning function can be used by registering maximum of 2048 display devices free of charge for

90 days after installing the “Multi Monitoring & Control Software” into a PC. To continuously use after the 90 days, it is necessary to purchase the license of “Early Warning Software” (ET-SWA100 Series) and perform the activation. Also, depending on the type of license, the number of display devices that can be registered for monitoring varies. For details, refer to the Operating Instructions of “Multi Monitoring & Control Software”.

fGeometric & Setup Management Software (Geometry Manager Pro)

This application software performs detailed corrections and adjustments such as the geometric adjustment which cannot be covered by the projector settings in real-time. By applying the optional Upgrade Kit (Model No.: ET-UK20), the correctable range and functions can be expanded. Also, by applying the optional Auto Screen Adjustment Upgrade Kit (Model No.: ET-CUK10), the geometric adjustment and edge blending matching the shape of the screen using a camera, and the adjustments of color and luminance can be automatically

performed with simple steps.

“Geometric & Setup Management Software” can be downloaded from the Panasonic website (https://panasonic. net/cns/projector/pass/). It is necessary to register and login to PASS*1 to download.

*1 PASS: Panasonic Professional Display and Projector Technical Support Website

For details, visit the Panasonic website (https://panasonic.net/cns/projector/pass/).

Storing

To store the projector, store in a dry room.

ENGLISH - 25

Chapter 1 Preparation — Precautions for use

Disposal

To dispose of the product, ask your local authorities or dealer for correct methods of disposal. Also, dispose of the

product without disassembling.

Cautions on use

rTo get a good picture quality

In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.

rDo not touch the surface of the projection lens with your bare hands.

If the surface of the projection lens becomes dirty from ngerprints or anything else, this will be magnied and projected onto the screen.

Attach the lens cover supplied with the projector or with the optional projection lens to the projector when you do not use the projector.

rDLP chips

fThe DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always

lit. Such a phenomenon does not indicate malfunction.

fDirecting a high-power laser beam onto the projection lens surface can damage the DLP chips.

rDo not move the projector or subject it to vibration or impact while it is operating.

Doing so may shorten the life of the built-in motor.

rLight source

The light source of the projector uses laser diode, and has the following characteristics.

fDepending on the operating environment temperature, the luminance of the light source will decrease.

The higher the temperature becomes, the more the luminance of the light source decreases.

fThe luminance of the light source will decrease by duration of usage.

If brightness is noticeably reduced and the light source does not turn on, ask your dealer to clean inside the

projector or replace the light source unit.

rComputer and external device connections

When connecting a computer or an external device, read this manual carefully regarding the use of power cords

and shielded cables as well.

26 - ENGLISH

Chapter 1 Preparation — Precautions for use

Accessories

Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the

number of accessories.

Wireless/wired remote control unit <1>

(N2QAYA000060)

Power cord

(K2CN3YY00018) 200 V - 240 V

(K2CT3YY00067) 200 V - 240 V

For India

(K2CZ3YY00092) <1> 200 V - 240 V

Lens Mount Cover <1>

(Black model: 1GE1RZ970BU) (White model: 1GE1RZ970WU)

(The same color as the outer case will be supplied.)

Lens cover <1>

(TKKL5244-1)

(Only models with lens)

(K2CG3YY00174) 100 V - 120 V

For Taiwan

(K2CG3YY00145) <1> 100 V - 120 V

Attention

fAfter unpacking the projector, discard the power cord cap and packaging material properly. fDo not use the supplied power cord for devices other than this projector. fFor missing accessories, consult your dealer. fStore small parts in an appropriate manner, and keep them away from small children.

Note

AAA/R03 or AAA/LR03 battery <2>

(For remote control unit)

fThe type and number of the supplied power cords vary depending on the country or region where you purchased the

product.

fThe part numbers of accessories are subject to change without prior notice.

ENGLISH - 27

Chapter 1 Preparation — Precautions for use

Optional accessories

Optional accessories (product name) Model No.

Projection lens

Ceiling Mount Bracket

Early Warning Software (Basic license/3-year license)

Upgrade Kit ET-UK20

Auto Screen Adjustment Upgrade Kit ET-CUK10 Auto Screen Adjustment Upgrade Kit (PC) ET-CUK10P Digital Interface Box ET-YFB100G DIGITAL LINK Switcher ET-YFB200G

*1 This product is equivalent to the lens attached to the projector models with standard zoom lens.

The availability of this product varies depending on the country. For details, contact your dealer.

*2 The sufx of the Model No. differs according to the license type.

Zoom Lens

Fixed-focus Lens ET-DLE035, ET-DLE055

Note

ET-DLE020, ET-DLE060, ET-DLE085, ET-DLE105, ET-DLE150, ET-DLE170*1, ET-DLE250, ET-DLE350, ET-DLE450

ET-PKD120H (for High Ceilings) ET-PKD120S (for Low Ceilings) ET-PKD130H (for High Ceilings, 6-axis Adjustment) ET-PKD130B (Projector Mount Bracket)

ET-SWA100 Series

fThe model numbers of optional accessories are subject to change without prior notice. fThe optional accessories compatible with the projector may be added or changed without prior notice.

For the latest information, visit the Panasonic website (https://panasonic.net/cns/projector/).

28 - ENGLISH

Chapter 1 Preparation — About your projector

About your projector

Remote control

Front Top

2 3

1 Power standby <v> button

Sets the projector to the state where the projector is turned off (standby mode) when the <MAIN POWER> switch on the projector is set to <ON> and in projection mode.

2 Power on <b> button

Sets the projector to projection mode when the <MAIN POWER> switch on the projector is set to <ON> and the power is turned off (standby mode).

3 Remote control indicator

Blinks if any button in the remote control is pressed.

4 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)

Adjusts the focus, zoom, and lens shift. (x page 70)

5 <MENU> button/<ENTER> button/

Used to navigate through the menu screen. (x page 79)

asqw

[SECURITY] or enter characters.

6 <ON SCREEN> button

Switches the on-screen display function on (display) or off (hide). (x page 75)

7 Input selection buttons (<RGB1/2>, <DIGITAL LINK>,

<DVI-D>, <SDI>, <HDMI>)

Switches the input signal to project. (x page 69) The <VIDEO> button is not used with this projector.

8 <FUNCTION> button

Assigns a frequently used operation as a shortcut button. (x page 76)

buttons are also used to enter the password in

asqw

buttons

13 14

Bottom

9 Number (<0> - <9>) buttons

Used for entering an ID number or a password in a multiple

projector environment.

10 <AUTO SETUP> button

Automatically adjusts the image display position while projecting

the image.

[PROGRESS] is displayed while in automatic adjustment. (x page 76)

11 <SHUTTER> button

Used to temporarily turn off the image. (x page 75)

12 <TEST PATTERN> button

Displays the test pattern. (x page 76)

13 <STATUS> button

Displays the projector information.

14 <DEFAULT> button

Resets the setting of the displayed sub-menu to the factory

default. (x page 80)

15 <ID SET> button

Sets the ID number of the remote control in a multiple projector environment. (x page 34)

16 Remote control signal transmitter

17 Remote control wired terminal

This is a terminal used to connect to the projector via a cable

when the remote control is used as a wired remote control.

(x page 34)

Attention

fDo not drop the remote control. fAvoid contact with liquids or moisture. fDo not attempt to modify or disassemble the remote control. fObserve the following instructions that are indicated on the caution label at the back of the remote control:

gDo not use old battery with new one. gDo not use batteries other than the type specied.

ENGLISH - 29

Chapter 1 Preparation — About your projector

gBe sure the batteries are inserted properly.

For other instructions, read the instructions related to batteries that are described in “Read this rst!”.

Caution label at the back of the remote control

Note

fWhen operating the remote control by directly pointing at the remote control signal receiver of the projector, operate the remote control

within a distance approximately 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°

vertically and horizontally, but the effective control range may be reduced. fIf there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly. fThe signal will be reected off the screen. However, the operating range may be limited from light reection loss due to the screen material. fIf the remote control signal receiver directly receives strong light, such as uorescent light, the remote control may not operate properly. Use

it in a place distant from the light source. fThe power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.

30 - ENGLISH

+ 210 hidden pages