Panasonic PT-RZ670B, PT-RZ670LB, PT-RZ670LW, PT-RZ670W User Manual

PEC

S

F

ILE

Product Number :

Product Name :

PT-RZ670B/RZ670W
PT-RZ670LB/RZ670LW

DLP™Projectors

As of September 2014. Specifications and appearance are subject to change without notice.

SFD14M021

1/18

DLPTM Projector

PT-RZ670B/RZ670W/RZ670LB/RZ670LW

Specifications

Main unit

Power supply

Power consumption

Standby Mode (Eco)*

Standby Mode (Normal)
BTU value
DLP™ chip Panel size

Display method

Pixels
Lens PT-RZ670K/RZ670W

PT-RZ670LK/RZ670LW
Light Source

Screen size

Brightness*
Center-to-corner uniformity*
Contrast*

2

2

2

Resolution

Scanning frequency SDI

HDMI/DVI-D

RGB

YP

(YCBCR)

BPR

Video/S-Video

As of September 2014 2/18

SFD14M021

AC100 - 240V 9.0 - 4.0A 50Hz/60Hz
(Taiwan: AC110V 8.0A 60Hz)

720W (735VA at 240V AC) (Taiwan: 730VA at 110VAC)
NORMAL: 558W ECO: 480W LONG LIFE1: 448W LONG LIFE 2: 430W
LONG LIFE 3: 407W
*Operating Temperature: 25 °C (77 °F), Altitude: 700m (22 ft 12 in),
ICE627087: 2008 Broadcast contents,
Picture mode: Standard, Dynamic contrast2

1

0.3W, 0.2W (Taiwan)
3W
Max 2,457 BTU (Without light 2,368 BTU)

17.0 mm (0.67 in) diagonal (16:10 aspect ratio)
DLP™ chip × 1, DLP™ system
2,304,000 (1,920 × 1,200) × 1, total of 2,304,000 pixels
Powered zoom/focus lenses (1.7–2.4:1), F 1.7–1.9, f 25.6–35.7 mm
Optional powered zoom/focus lenses and fixed-focus lens
Laser Diode (Laser class: Class 1) *Class 3R for North America.

Luminance life for set: 20,000 hours at half luminance (normal)/
24,000 hours at half luminance (Eco)
* Temperature: 35°C(95°F), Altitude 700m (22ft 12in), Dust: 0.15mg/m

1.27–15.24 m (50–600 inches)
*1.27 – 5.08 m (50 – 200 inches) with the ET-DLE055 (16:10 aspect ratio)
*2.54 – 7.62 m (100 – 350 inches) with the ET-DLE030 (16:10 aspect ratio)
6,500 lumens (Operation mode: NORMAL)
90%
10,000:1㸦full on/full off, dynamic contrast ON㸧
1,920 × 1,200 pixels

3G-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p

3G-SDI signal (YP

4:2:2 10-bit):

BPR

SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p

HD-SDI signal (YP

4:2:2 10-bit):

BPR

SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i,

1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,

1125(1080)/24sF, 1125(1080)/30p

SD-SDI signal (YC

4:2:2 10-bit):

BCR

SMPTE ST 259 compliant: 525i(480i), 625i(576i)
fH: 15- 100kHz, fV: 24 - 120Hz, dot clock: 25 - 162 MHz
525i (480i)*3, 625i (576i)*3, 525p (480p), 625p (576p), 750 (720)/60p,

750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p,
1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p,

1125 (1080)/50p, VGA (640 x 480) - WUXGA*4 (1920 x 1200) compatible
with non-interlaced signals only

fH: 15- 100kHz, fV: 24 - 120Hz, dot clock: 20 - 162 MHz
525i (480i): f

15.75 kHz; fV60 Hz,

H

625i (576i): fH15.63 kHz; fV50 Hz,
525p (480p): f

H 31.50 kHz; fV 60 Hz,

625p (576p): fH31.25 kHz; fV50 Hz,
750 (720)/60p: fH

45.00 kHz; fV60 Hz,
750 (720)/50p: fH37.50 kHz; fV50 Hz,
1125 (1035)/60i: fH33.75 kHz; fV60 Hz,
1125 (1080)/60i: f

H 33.75 kHz; fV 60 Hz,

1125 (1080)/50i: fH 28.13 kHz; fV 50 Hz,
1125 (1080)/25p: f

28.13 kHz; fV25 Hz,

H

1125 (1080)/24p: fH27.00 kHz; fV24 Hz,
1125 (1080)/24sF: fH27.00 kHz; fV48 Hz,

H

1125 (1080)/30p: f

33.75 kHz; fV30 Hz,
1125 (1080)/60p: fH 67.50 kHz; fV 60 Hz,
1125 (1080)/50p: f

56.25 kHz; fV50 Hz

H

fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

3

DLPTM Projector

PT-RZ670B/RZ670W/RZ670LB/RZ670LW

Optical axis shift Vertical: +50%, -16%(powered),

Horizontal: +30%, -10%(When using the ET-DLE085, +28%, -10％)

Keystone correction range

Vertical㸸±40°*

5

/ Horizontal: ±15°*

6

(When using the optional upgrade kit ET-UK20
Vertical㸸±45°*

8/10

/ Horizontal㸸±40°*

9/10

)

Installation Ceiling/floor, front/rear, 360 degree free installation

Terminals SDI IN

BNC × 1,

3G-SDI signal: SMPTE ST 424 compliant

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

HDMI IN

HDMI 19-pin × 1, Deep Color, compatible with HDCP,

525i (480i), 625i (576i), 525p (480p), 625p (576p), 750 (720)/60p,

750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p,

1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p,

1125 (1080)/50p

VGA (640 x 480) - WUXGA (1920 x 1200)

compatible with non-interlaced signals only

NOTE: Compatible with non-interlaced signals only.

DVI-D IN

DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP,

for single link only

525i (480i), 625i (576i), 525p (480p), 625p (576p), 750 (720)/60p,

750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p,

1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p,

1125 (1080)/50p

VGA (640 x 480) - WUXGA (1920 x 1200)

compatible with non-interlaced signals only

NOTE: Compatible with non-interlaced signals only.

RGB 1 IN

R, G, B

BNC ×5

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y,

P

B, PR (Y, CB, CR)

Y,C

Video

RGB 2 IN

R, G, B

Y:

1.0 Vp-p (including sync signal), PB /PR (CB/CR): 0.7 Vp-p, 75 ohms

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

1.0Vp-p, 75 ohms

D-sub HD 15-pin (female) ×1

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y, P

, PR(Y, CB, CR)

B

SERIAL IN

SERIAL OUT

REMOTE 1 IN

REMOTE 1 OUT

Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms

D-sub 9-pin (female) ×1 for external control (RS-232C compliant)

D-sub 9-pin (male) x 1 for link control

M3 jack x 1 for wired remote control

M3 jack x 1 for link control (for wired remote control)

REMOTE 2 IN D-sub 9-pin (female) x1 for external control (parallel)

LAN/DIGITAL LINK

RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control)
connection, 100Base-TX, compatible with Art-Net,
compliant with PJLink(TM)(Class 1)

As of September 2014 3/18

SFD14M021

DLPTM Projector

PT-RZ670B/RZ670W/RZ670LB/RZ670LW

Power cord length
Cabinet materials
Dimensions (W × H × D) PT-RZ670B/RZ670W

PT-RZ670LB/RZ670LW

Weight PT-RZ670B/RZ670W

PT-RZ670LB/RZ670LW
Operation noise
Operating temperature
Operating humidity

Remote control unit

Power supply
Operation range

Dimensions (W × H × D)

12

Weight*

Supplied accessories

3.0 m (9 ft 10 in)
Molded plastic
498 x 200*

11

x 581mm
(19-19/32 x 7-7/8*11 x 22-7/8in ) with supplied lens
498 x 200*
(19-19/32 x 7-7/8*

11

x 538 mm

11

x 21-3/16in) without lens
Approx. 23.2kg (51.1lbs) with supplied lens
Approx. 22.5kg (49.6lbs) without lens
35 dB
0–45 °C (32–113 °F)*

13

10%–80% (no condensation)

3 V DC (R03/AAA type battery × 2)
Approx. 30 m (98 ft 5 in) when operated from directly in front of the
signal receptor
48 × 145 × 27 mm (1-57/64 × 5-45/64 × 1-3/64 in)
Approx. 102 g (3.6 oz) including batteries

Power cord with secure lock (x 1) (x 2 for EU models)
Wireless/wired remote control unit (× 1)
Batteries for remote control (R03/AAA type×2)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)

Optional accessories

Digital interface box

ET-YFB100G

Zoom lens (0.8–1.0:1) ET-DLE085
Zoom lens (1.3–1.9:1)
Zoom lens (2.3– 3.6:1)
Zoom lens (3.6– 5.4:1)
Zoom lens (5.4– 8.6:1)

Fixed-focus lens (0.38:1)
Fixed-focus lens (0.8:1)
Ceiling mount bracket

ET-DLE150
ET-DLE250
ET-DLE350
ET-DLE450
ET-DLE030
ET-DLE055
ET-PKD120H (for high ceilings)
ET-PKD120S (for low ceilings)

High-ceiling mount bracket

ET-PKD130H

(6-axis adjustment mechanism)
Attachment for ceiling mount bracket
Geometry Manager Pro Upgrade kit
Auto Screen Adjustment Upgrade kit

ET-PKD130B

-UK20

ET
ET-CUK10*

14

Early Warning Software ET-SWA100

*1 When the STANDBY MODE is set to Eco, network functions such as power on over the LAN will not operate
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards
*3 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking)
*5 +/- 22° with the ET-DLE085/DLE055 and +5°with the ET-DLE030
*6 Not operatable with the ET-DLE030
*7 +/-30° with the ET-DLE085/DLE055
*8 +/-40°with the ET-DLE150/DLE250/supplied lens and +/-22°with the ET-DLE085/DLE055
*9 +/-15°with the ET-DLE085/DLE055
*10 up to a total of +/-55°during simultaneous horizontal and vertical correction
*11 with legs at shortest position
*12 Average value. May differ depending on models
*13 Limits the luminance when used in locations from 0m to 2700m (0ft to 8858ft) above sea level at ambient temperatures of 35°C (95°F) or higher,
or from 2700m to 4200m (8858ft to 13780ft) above sea level at ambient temperatures of 25°C (77°F) or higher.
*14 Available for use worldwide except in the US.

As of September 2014 4/18

SFD14M021

DLPTM Projector

Dimensions

580.8
(22-7/8)

PT-RZ670B/RZ670W/RZ670LB/RZ670LW

(10-19/32)(10-19/32)

538

(21-3/16)

442 (17-13/32)

498 (19-19/32)

Terminals

1

2345

678910 11

269 269

28

115.5
(4-9/16)

42.8

(1-3/32)

(1-11/16)

181

19

(7-1/8)

96.5

(3/4)

unit : mm (inch)
NOTE: This illustration is not drawn to scale.
The illustration shows the PT-RZ670B/RZ670W.

(3-13/16)

4

(5/32)

432 (17)

444 (15/32)

457 (18)

1 Remote 1 input

2 Remote 1 output

3 Remote 2 input

4 Serial input

5 Serial output

6 SDI input

7 RGB 1 input

8 RGB 2 Input

9 DVI-D input

10 HDMI input

11 LAN/DIGITAL LINK connector

200

(7-7/8)

As of September 2014 5/18

SFD14M021

DLPTM Projector

PT-RZ670B/RZ670W/RZ670LB/RZ670LW

Standard setting-up position (If using other than the ET-DLE030)

2

*

352–432

(13-27/32–17)

294244

Upper edge of projected image

EE

ø60.5

L

1

*

(11-9/16)(9-19/32)

*1 When the lens protrudes to the maximum.

2

463.5–543.5*

84 mm (3-5/16 in) with the ET-DLE085
43 mm (1-11/16 in) wi th the supplied lens
44 mm (1-23/32 in) wi th the ET-DLE150
45 mm (1-25/32 in) wi th the ET-DLE250
51mm (2 in) with the ET-DLE350
95mm (3 -3/4 in) with the ET-DLE450
27 mm (1-1/16 in) with the ET-DLE055

*2 Adjustable in 40 mm (1-9/16 in) steps.

(18-1/4–21-13/32)

Lower edge of projected image

unit : mm (inch)

370

100

Projected image

100
(3-15/16)

259

(10-3/16)

(14-9/16)

(3-15/16)

NOTE:

Illustrations show the projector
installed using optional ceiling mount
bracket ET-PKD120H, optional bracket
assembly ET-PKD130B and an optional
lens.

This illustration is not drawn to scale.

Caution:

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket. Furthermore, in order to prevent it from falling

down from the ceiling, use the supplied wire on the mounting bracket.

As of September 2014 6/18

SFD14M021