Panasonic PT-RZ31KEJ Product Data Sheet

PEC
S
ILE
Product Number :
Product Name :
PT-RZ31K
3-Chip DLP™Projector
As of September 2016. Specifications and appearance are subject to change without notice.
SFD16M045
1/18
3-Chip DLP™ Projector
Specifications
Main unit
Power supply
Power consumption
BTU value
DLP™ chip Panel size
Display method
Pixels
Lens
Light source
Illumination life of set
Filter
Normal filter
Long life filter unit
Screen size
Brightness*
Center-to-corner uniformity*
Contrast*
Resolution
Scanning frequency
1
1
1
Video/YC fH:15.73KHz fV:59.94Hz, fH:15.63KHz fV:50Hz
RGB • Resolution: 640 x 400 pixels to 1920 x 1200 pixels
• Dot clock frequency: 162MHz or less
• PIAS (Panasonic Intelligent Auto Scanning)
BPR(YCBCR) • Resolution: 480i/576i to 1920 x 1080 pixels
YP
• Dot clock frequency: 148.5MHz or less
• The SYNC/HD and VD terminals do not support 3 value SYNC.
DVI • Moving image signal resolution: 480i*5/576i*5 to 1920x1080
Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)
• Dot clock frequency: 25 MHz to 162 MHz
PT-RZ31K
AC 100-120 V, 50/60 Hz; AC 200-240 V, 50/60 Hz
2,870 W (2,870 VA AC200V)
Average power consumption Varies depending on operation mode setting.)
HIGH: 2,310W NORMAL: 1,890W
LONG LIFE 1: 1,040-1,680W
LONG LIFE 2: 924-1,580W
LONG LIFE 3: 794-1,460W
*Operating Temperature: 25 °C (77 °F),
Altitude: 700m (2,297ft), IEC627087: 2008 Broadcast contents,
Picture mode: Standard, Dynamic contrast [2]
0.3 W with STANDBY MODE set to ECO
4 W with STANDBY MODE set to NORMAL
Max 9,806 BTU
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™chip ×3 (R, G, B), DLP™projection system
2,304,000 (1920 ×1200) ×3, total of 6,912,000 pixels
Optional powered zoom/focus lenses Laser Diode Laser class 1
Varies depending on operation mode setting.
Luminance life for set: 18,000 hours at half luminance (HIGH)/
8,000 hours at 70% luminance
20,000 hours at half luminance (NORMAL)
43,800 hours at constant luminance (LONG LIFE 1)/
61,320 hours at constant luminance (LONG LIFE 2)/
87,600 hours at constant luminance (LONG LIFE 3)
* IEC62087: 2008 Broadcast contents, Dynamic contrast [3] Varies depending on operation mode setting.
4,000 hours (NORMAL)/2,000 hours (HIGH)/ 20,000 hours (LONG LIFE 1/2/3)
20,000 hours (NORMAL)/4,000 hours (HIGH)/ 40,000 hours (LONG LIFE 1/2/3)
1.78–25.4 m (70–1,000 inches) (16:10 aspect ratio)
1.78–15.24 m (70–600 inches) with the ET-D75LE8 (16:10 aspect ratio)
3.05–15.24 m (120–600 inches) with the ET-D75LE95 (16:10 aspect ratio) Varies depending on operation mode setting.
2*4
30,000 lm*
25,000 lm*2*4/26,000 lm*3*4 (Center) (NORMAL)
12,000 lm at constant luminance (LONG LIFE 1)
10,000 lm at constant luminance (LONG LIFE 2)
8,000 lm at constant luminance (LONG LIFE 3) 90%
20,000:1 (full on/full off, in Dynamic Contrast 3 mode)
1920 ×1200 pixels (Input signals that exceed this resolution will be
converted to 1920 ×1200 pixels.)
/31,000 lm*3*4 (Center) (HIGH)
As of September 2016 2/18
SFD16M045
3-Chip DLP™ Projector
PT-RZ31K
Scanning frequency
HDMI/DIGITAL LINK • Moving image signal resolution: 480i*5/576i*5 to 1920x1080
Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)
• Dot clock frequency: 25 MHz to 162 MHz
SDI SD-SDI signal
HD-SDI signal
3G-SDI signal
For details of the types of video signals that can be used with the projector, refer to “List of compatible signals”
Keystone correction range
Projection
lens Model
No.
ET-D75LE6
ET-D75LE8 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE50
ET-D75LE95*
When using the optional Upgrade Kit (Model No.: ET-UK20)
Projection
lens Model
No.
ET-D75LE6
ET-D75LE8 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE50
ET-D75LE95*
Only [KEYSTONE] used [KEYSTONE] and [CURVED] used together Only [CURVED] used
angle α (°)
6
angle α (°)
6
Vertical
keystone
correction
± 28 ± 40 ± 40 ± 40 ± 40 ± 40 ± 22
+5 / -0
Only [KEYSTONE] used*
Vertical
keystone
correction
± 28 ± 45 ± 40 ± 40 ± 45 ± 45 ± 22
+5 / -0
Horizontal
keystone
correction
angle β (°)
± 15 ± 15 ± 15 ± 15 ± 15 ± 15 ± 15
0
Horizontal
keystone
correction
angle β (°)
± 15 ± 40 ± 40 ± 40 ± 40 ± 40 ± 15
0
Vertical
keystone
correction
angle α (°)
± 10 ± 20 ± 20 ± 20 ± 20 ± 20
7
Vertical
keystone
correction
angle α (°)
± 10 ± 20 ± 20 ± 20 ± 20 ± 20
Horizontal
keystone
correction
angle β (°)
± 8
-
[KEYSTONE] and [CURVED] used together Only [CURVED] used
Horizontal
keystone
correction
angle β (°)
± 8
-
± 10 ± 15 ± 15 ± 15 ± 15 ± 15
± 10 ± 15 ± 15 ± 15 ± 15 ± 15
Min. value of
± 8
-
Min. value of
± 8
-
R2/L2
1.6
0.2
1.1
0.9
0.6
0.4
2.0
R2/L2
1.2
0.2
0.9
0.7
0.5
0.3
1.5
Min. value of
-
Min. value of
-
3/L3
3.9
0.4
2.6
1.7
1.2
0.7
4.9
3/L3
3.0
0.3
2.0
1.3
0.9
0.5
3.7
Min. value of
-
Min. value of
-
R2/L2
0.9
0.2
0.6
0.5
0.4
0.2
1.2
R2/L2
0.7
0.1
0.5
0.4
0.3
0.2
0.9
Min. value of
R3/L3
2.3
0.3
1.5
1.0
0.7
0.4
2.9
-
-
-
Min. value of
R3/L3
1.7
0.2
1.1
0.7
0.5
0.3
2.2
-
[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)
Screen
Screen
Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)
Screen
Arc center
Screen
Projection distance Arc radius
Projection distance Arc radius
Screen
Arc center
Screen
Projection distance Arc radius
Projection distance Arc radius
Optical axis shift Vertical ±55% (±44% with the ET-D75LE6), (+68-78% with the ET-D75LE95),
from center of screen, powered
Horizontal
±20% (±15% with the ET-D75LE6), (±12% with the ET-D75LE95),
from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.
Installation
Ceiling/floor, front /rear, free 360-degree installation
As of September 2016 3/18
SFD16M045
3-Chip DLP™ Projector
PT-RZ31K
Terminals
Power cord length
Cabinet materials
Dimensions (W ×H × D):
Weight*
10
RGB1 IN BNC × 5
R,G,B R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
B, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Y, P
Y/C Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms
VIDEO IN BNC × 1, 1.0 Vp-p, 75 ohms
RGB2 IN D-sub HD 15-pin (female) × 1
R,G,B R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
DVI-D IN DVI-D 24-pin ×1
Single link, DVI 1.0 compliant, HDCP compatible
HDMI IN HDMI 19-pin x1
HDCP compatible, Deep Color compatible
SDI IN 1 BNC × 1
SD-SDI signalSMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI (LINK-A) signal SMPTE ST 372 compliant
Dual link 3G-SDI (Link 1) signal SMPTE ST 425 compliant
SDI IN 2 BNC × 1
SD-SDI signalSMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI (LINK-B) signal SMPTE ST 372 compliant
Dual link 3G-SDI (Link 2) signal SMPTE ST 425 compliant
DIGITAL LINK RJ-45
HDBaseT™ compliant, HDCP compatible, Deep Color compatible
3D SYNC1 IN/OUT /
MULTI PROJECTOR SYNC IN
BNC × 1, IN : TTL Hi-z OUT : TTL max10mA
3D SYNC2 OUT /
MULTI PROJECTOR SYNC OUT
BNC × 1, TTL max10mA
SERIAL IN D-sub 9 pin × 1 for external control (RS-232C compliant)
SERIAL OUT D-sub 9 pin × 1 for link control
REMOTE 1 IN M3 stereo mini jack × 1 for wired remote control
REMOTE 1 OUT M3 stereo mini jack × 1 for link control
REMOTE 2 IN D-sub 9 pin × 1 for external control (parallel)
DIGITAL LINK/LAN RJ-45 x 1 (for network, DIGITAL LINK connection, 100Base-TX,
compatible with Art-Net, PJLink™ (class 1), Deep Color, HDCP)
DC OUT 5V USB connector (type A) x 2 for power supply only (DC 5V, Max.900mA)
3.0 m (9 ft 10 in) ft
Processed metal parts, Molded plastic
8
700 × 418* (27-9/16 × 16-15/32 700 × 373* (27-9/16 × 14-11/16
×1,250 mm
9
×1,070 mm
×49-7/32 inches) (with protrusion parts)
×42-1/8 inches) (without protrusion parts)
79 kg (174.2 lbs)
As of September 2016 4/18
SFD16M045
3-Chip DLP™ Projector
PT-RZ31K
Operation noise*
2
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range
Dimensions (W × H × D)
Weight
49 dB Varies depending on operation mode setting.
HIGH/NORMAL
The operating temperature range is 0°C to 50°C (32 °F to 122 °F).
(Less than 1,400m (4,593 ft) above sea level)
The operating temperature range is 0°C to 45°C (32 °F to 113 °F).
(Less than 1,400m (4,593 ft) to 4,200m (13,780 ft) above sea level)
• If using at ambient operating temperatures of 35 °C (95 °F) or higher and at
less than 2,700m (8,858 ft) above sea level, or at ambient operating
temperatures of 25 °C (77 °F) or higher and between 2,700m (8,858 ft) and
4,200m (13,780 ft) above sea level, the brightness of the light source may
drop in order to protect the projector.
LONG LIFE 1/2/3
The operating temperature range is 0°C to 45°C (32 °F to 113 °F).
(Less than 2,700m (8,858 ft) above sea level)
• If using at ambient operating temperatures of 35 °C (95 °F) or higher,
the brightness of the light source may drop in order to protect the projector.
When using a smoke cut lter (regardless of operating mode)
0 °C to 40 °C (32 °F to 104 °F) Less than 1,400 m (4,953 ft) above sea level
10%–80% (no condensation)
3 V DC (AA/R6 type battery ×2)
Approx. 30 m (985 in) ftwhen operated from directly in front of the
signal receptor
47.5 × 181.5 × 27.5 mm (1-7/8 × 7-5/32 × 1-3/32 inches)
Approx. 150 g (5.3 oz) (including batteries)
Supplied accessories
Power cord (×3)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA/R6 type ×2)
Lens drop-prevention screw (× 1) Replacement filter unit (ET-EMF330) (× 4) Lens hole cover (× 1)
e CD-ROM (Logo Transfer Software, Multi Monitoring
Softwar
& Control Software) (× 1)
Optional accessories
Zoom lens (0.9–1.1:1)
Zoom lens (1.7–2.4:1)
Zoom lens (4.6–7.4:1)
Fixed-focus lens (0.7:1)
Replacement filter unit Early Warning Software ET-SWA100
Auto Screen Adjustment Upgrade Kit (PC) ET-CUK10P
ET-D75LE6
ET-D75LE20
ET-D75LE40
ET-D75LE50
ET-EMF330
Zoom lens (1.3–1.7:1)
Zoom lens (2.4–4.7:1)
Zoom lens (7.3–13.8:1)
ET-D75LE10
ET-D75LE30
ET-D75LE8
Fixed-focus lens (0.36:1) ET-D75LE95 Smoke cut filter Upgrade kit
ET-SFR330Long life filter unit ET-EMFU330
ET-UK20 Auto Screen Adjustment Upgrade Kit ET-CUK10 Digital interface box ET-YFB100G
Digital LINK Switcher ET-YFB200G
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for extern al control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *3 The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by the ISO/IEC 21118:2012 international standards. *4 In AC200V, When using a projection lens other than ET-D75LE95. *5 Pixel-Repetition signal(dot clock frequency 27.0MHz) only *6 Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves away from the screen. *7 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be made exceeding total of 55°. *8 With legs at shortest position. *9 Without legs. *10 Average value. May differ depending on the actual unit.
As of September 2016 5/18
SFD16M045
3-Chip DLP™ Projector
Dimensions
1070
[42-1/8]
unit : mm (inch) NOTE: This illustration is not drawn to scale.
25
[31/32]
[5]
127.5
373
418
245.5
290.5
[9-21/32]
[11-7/16]
350
[13-25/32]
700
[27-9/16]
When the long-life filter unit (Model No.: ET-EMFU330, sold separately) is installed
[14-11/16]
[16-15/32]
90
[3-9/16]
68
[2-11/16]
951
[37-7/16]
1250
[49-7/32]
PT-RZ31K
89.2
[3-1/2]
1070
[42-1/8]
335.8 [13-7/32]
290.5 [11-7/16]
25
127.5
245.5
[31/32]
[5]
[9-21/32]
350
[13-25/32]
112.2
[4-13/32]
700
[27-9/16]
25.6
258.9
73.3
[1]
[10-3/16]
[2-7/8]
418
[16-15/32]
[3-9/16]
373
[14-11/16]
90
68
[2-11/16]
951
[37-7/16]
1250
[49-7/32]
89.2
[3-1/2]
As of September 2016 6/18
SFD16M045
Loading...
+ 12 hidden pages