Panasonic PT-RZ12KEJ Datasheet
PEC
S
ILE
F
Product Number :
Product Name :
PT-RZ12K
3-Chip DLP™Projector
As of September 2015. Specifications and appearance are subject to change without notice.
SFD15M030
1/14
3-Chip DLP™ Projector
Specifications
Main unit
Power supply
Power consumption
BTU value
DLP™ chip Panel size
Display method
Pixels
Lens
Light source
Screen size
Brightness*
Center-to-corner uniformity*
Contrast*
Resolution
Scanning frequency SDI
2
2
2
HDMI/DVI-D
RGB Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz,
PT-RZ12K
AC 100–240 V 50/60 Hz
1,200 W (1,280 VA) (0.3 W with
STANDBY MODE set to NORMAL.),
STANDBY MODE set to ECO.*
Average power consumption
NORMAL: 800W ECO: 680W LONG LIFE1: 620W LONG LIFE 2: 590W
LONG LIFE 3: 550W
*Operating Temperature: 25 °C (77 °F), Altitude: 700m (22 ft 12 in),
ICE627087: 2008 Broadcast contents,
Picture mode: Dynamic, Dynamic Contrast3
Max 4,096 BTU
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™ chip ×3 (R, G, B), DLP™ projection system
2,304,000 (1,920 × 1,200) × 3, total of 6,912,000 pixels
Optional powered zoom/focus lenses
Laser Diode (Laser class: Class 1)
Luminance life for set: 20,000 hours at half luminance (normal)/
24,000 hours at half luminance (Eco)
* Temperature: 35°C(95°F), Altitude 700m (22ft 12in), Dust: 0.15mg/m
43,800 hours at constant luminance (Longlife1)
61,320 hours at constant luminance (Longlife2)
87,600 hours at constant luminance (Longlife3)
1.78–25.4 m (70–1,000 inches) (16:10 aspect ratio)
1.78–15.24 m (70–600 inches) with the ET-D75LE8 (16:10 aspect ratio)
3.05–15.24 m (120–600 inches) with the ET-D75LE90 (16:10 aspect ratio)
12,000 lumens
90%
20,000:1 (full on/full off, in Dynamic Contrast 3 mode)
1,920 × 1,200 pixels (Input signals that exceed this resolution will be
converted to 1,920 × 1,200 pixels.)
SD-SDI signal (YC
4:2:2 10-bit):
BCR
SMPTE ST 259 compliant: 525i(480i), 625i(576i)
Single-link HD-SDI
signal (YP
4:2:2 10-bit):
BPR
SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i,
1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,
1125(1080)/24sF, 1125(1080)/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 372 compliant: 1125(1080)/60i, 1125(1080)/50i,
1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
2048 ×1080/24p, 2048 ×1080/24sF,
Dual-link HD-SDI signal (X
Y Z 4:4:4 12-bit):
SMPTE ST 372 compliant: 2048 ×1080/24p, 2048 ×1080/24sF,
3G-SDI signal (YP
4:2:2 10-bit):
BPR
SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p
3G-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,
1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p
Dual-link 3G-SDI signal
(YP
4:4:4 12-bit/10-bit):
BPR
SMPTE ST 425 compliant: 1125(1080)/60i, 1125(1080)/50i,
2048 × 1080/48p, 2048 × 1080/50p, 2048 × 1080/60p
Dual-link 3G-SDI signal
(RGB 4:4:4 12-bit/10-bit):
SMPTE ST 425 compliant: 1125(1080)/60i, 1125(1080)/50i,
2048 × 1080/48p, 2048 × 1080/50p, 2048 × 1080/60p
Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz,
dot clock: 25 MHz – 162 MHz
dot clock: 162 MHz or less
1
4 W with
3
As of September 2015 2/14
SFD15M030
3-Chip DLP™ Projector
PT-RZ12K
Scanning frequency
(YCBCR) 525i (480i): fH15.73 kHz; fV59.94 Hz,
YP
BPR
H
625i (576i): f
525p (480p): f
15.63 kHz; fV50 Hz,
31.47 kHz; fV59.94 Hz,
H
625p (576p): fH31.25 kHz; fV50 Hz,
750 (720)/60p: f
750 (720)/50p: f
1125 (1035)/60i: f
1125 (1080)/60i: f
45.00 kHz; fV60 Hz,
H
37.50 kHz; fV50 Hz,
H
H
33.75 kHz; fV60 Hz,
33.75 kHz; fV60 Hz,
H
1125 (1080)/50i: fH28.13 kHz; fV50 Hz,
1125 (1080)/25p: f
1125 (1080)/24p: f
1125 (1080)/24sF: f
1125 (1080)/30p: f
28.13 kHz; fV25 Hz,
H
27.00 kHz; fV24 Hz,
H
H
27.00 kHz; fV48 Hz,
33.75 kHz; fV30 Hz,
H
1125 (1080)/60p: fH67.50 kHz; fV60 Hz,
56.25 kHz; fV50 Hz
H
Video/YC
1125 (1080)/50p: f
H: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
f
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift Vertical ±55% (±44% with the ET-D75LE6), (+73-78% with the ET-D75LE90),
from center of screen, powered
Horizontal
±20% (±15% with the ET
-D75LE6), (±6% with the ET-D75LE90),
from center of screen, powered
Keystone correction range
Installation
Terminals SDI IN 1
Projection
lens Model
No.
ET-D75LE6
ET-D75LE8
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE50
ET-D75LE90
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.
Standard status
Only [KEYSTONE]
used
Vertical Horizontal Vertical HorizontalVertical HorizontalVertical Horizontal
±28
±40
±40
±40
±40
±40
±22
+5/-0
±15
±15
±15
±15
±15
±15
±15
[KEYSTONE] and
[CURVED] used together
±10
±20
±20
±20
±20
±20
0
±8
-
±10
±15
±15
±15
±15
±15
±8
-
When using the optional Upgrade Kit
(Model No.: ET-UK20)
Only [KEYSTONE]
used
±28
±45
±40
±40
±45
±45
±22
+5/-0
±15
±40
±40
±40
±40
±40
±15
[KEYSTONE] and
[CURVED] used together
±10
±20
±20
±20
±20
±20
0
±8
-
Ceiling/floor, front/rear
BNC × 2,
(3G/HD/SD-SDI, Dual-link HD-SDI, Dual-link 3G-SDI)
Dual-link 3G-SDI signal: SMPTE ST 425 compliant
3G-SDI
signal: SMPTE ST 424 compliant
Dual-link HD-SDI signal: SMPTE ST 372 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
HDMI IN
DVI-D IN
RGB 1 IN
R, G, B
HDMI 19-pin × 1, Deep Color, compatible with HDCP,
NOTE: Compatible with non-interlaced signals only.
DVI-D 24-pin ×1, DVI 1.0 compliant, HDCP compatible, for single link only
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
B, PR (Y, CB, CR)
Y, P
Video in
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC ×1, 1.0 Vp-p 75 ohms
Y/C Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms
RGB 2 IN
R, G, B
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
Y, P
, PR(Y, CB, CR)
B
Y: 1.0 Vp-p (including sync signal), P
B/PR(CB/CR
): 0.7 Vp-p, 75 ohms
±10
±15
±15
±15
±15
±15
±8
-
As of September 2015 3/14
SFD15M030
3-Chip DLP™ Projector
PT-RZ12K
Power cord length
Cabinet materials
Dimensions (W ×H × D):
5
Weight*
Operation noise*
2
Operating temperature
Operating humidity
3D SYNC 1 IN/OUT
3D SYNC 2 OUT
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
REMOTE 2 IN
DIGITAL LINK/LAN
BNC × 1, 1.0 Vp-p, 75 ohms
Input: TTL, high impedance. Output: TTL, max. 10 mA
BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
D-sub 9-pin (female) ×1 for external control (RS-232C compliant)
D-sub 9-pin (male) ×1 for link control
M3 jack ×1 for wired remote control
M3 jack ×1 for link control
D-sub 9-pin ×1 for external control (parallel)
RJ-45 Network connection / digital link connection (video/network/serial
control) compliant with PJLink,100base-tx, Art-Net compatible
3.0 m (9
10 in)
Molded plastic
4
578 × 323.5*
(22-3/4 × 12-23/32*
× 740 mm
4
× 29-1/8 inches) (without lens)
44 kg (97.0 lbs) (without lens)
43 dB
Normal
The operating temperature range is 0°C to 50°C (32 °F to 122 °F).
(Brightness is limited at operating temperatures of 35°C (95°F) or more
at altitudes from 700 m to 2,700 m (2,297 ft to 8,858 ft) above sea level,
and at operating temperatures of 25°C (77°F) or more at altitudes from
2,700 m to 4,200 m (8,858 ft to 13,780 ft) above sea level.)
Eco/Long life 1/2/3
The operating temperature range is 0°C to 45°C (32 °F to 113 °F).
(Brightness is limited at operating temperatures of 35°C (95°F) or more
at altitudes up to 2,700 m (8,858 ft) above sea level. The projector cannot
be used at altitudes of 2,700 m (8,858 ft) or more above sea level.)
When the projector is used with a Smoke Cut Filter
The operating temperature range is 0°C to 40°C (32 °F to 104 °F).
(The projector cannot be used at altitudes of 1,400 m (4,593 ft) or more
above sea level.)
* The brightness of the light source may drop depending on the operating
temperature range. The higher the temperture, the greater the drop in the
brightness of the light source will be.
10%–80% (no condensation)
Remote control unit
Power supply
Operation range*
6
3 V DC (AA/R6 type battery ×2)
Approx. 30 m (98
5 in) when operated from directly in front of the
signal receptor
Dimensions (W × H × D)
Weight
47.5 × 181.5 × 27.5 mm (1-7/8 × 7-5/32 × 1-3/32 inches)
Approx. 150 g (5.3 oz) (including batteries)
Supplied accessories
Power cord (×1) (x2 for PT-RZ12KE)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA/R6 type ×2)
Lens drop-prevention screw (× 1)
Softwar
e CD-ROM (Logo Transfer Software, Multi Monitoring
& Control Software) (× 1)
Weights and dimensions shown are approximate. Specifications a nd appearance are subject to change without notice.
1 When the standby mode is set to eco, network functions such as power on over the L AN network will not operate, and the serial output termi-
*
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
2 Measurement, measuring c onditions, a nd method of notation all comply with ISO 21118 international standards.
*
3 Up to a total of ±55° during simultaneous horizontal and vertical correction.
*
4 With legs at shortest position.
*
5Average value (excluding the optional lens). May differ depending on models.
*
*6 Operation range differs depending on environments.
As of September 2015 4/14
SFD15M030
3-Chip DLP™ Projector
Optional accessories
Zoom lens (0.9–1.1:1)
Zoom lens (1.7–2.4:1)
Zoom lens (4.6–7.4:1)
Fixed-focus lens (0.7:1)
Lens motor cover
Ceiling mount bracket (for high ceilings) Ceiling mount bracket (for low ceilings)
Projector mount bracket ET-PAD520B
Smoke cut filter
Upgrade kit
Early Warning Software ET-SWA100
Digital interface box ET-YFB100G
Replacement filter unit
ET-D75LE6
ET-D75LE20
ET-D75LE40
ET-D75LE50
ET-D75MC1
ET-PKD520H
ET-SFR330
ET-UK20
ET-EMF330
Zoom lens (1.3–1.7:1)
Zoom lens (2.4–4.7:1)
Zoom lens (7.3–13.8:1)
Fixed-focus lens (0.36:1) ET-D75LE90
Frame
Auto sreen adjustment upgrade kit ET-CUK10
Digital LINK Switcher ET-YFB200G
PT-RZ12K
Dimensions
ET-D75LE10
ET-D75LE30
ET-D75LE8
ET-PKD520S
ET-PFD510
Terminals
484 (19-1/16)
578 (22-3/4)
725 (28-17/32)
15
(19/32)
270 (10-5/8)
195.5
142
(7-11/16)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
(5-19/32)
1 Remote 1 input
2 Remote 1 output
3 Remote 2 input
4
Serial input
5
Serial output
6
3D sync 1 input/output
7
3D sync 2 output
8
SDI 1 input
9SDI 2 input
10
RGB 1 input
11
RGB 2 Input
12
DVI-D input
13
HDMI input
14
LAN/DIGITAL LINK connector
As of September 2015 5/14
SFD15M030
Loading...