S P E C F I L E
Product Number : PT-RX110B/RX110W
PT-RX110LB/RX110LW
Product Name : |
DLP™ Projectors |
As of August 2016. Specifications and appearance are subject to change without notice. |
1 / 1 8 |
SFD16M036
DLP™ Projector
PT-RX110B/RX110W/RX110LB/RX110LW
Speci cations
Main unit |
|
|
Power supply |
|
AC100 - 240V 10.4-5.0A 50Hz/60Hz |
Power consumption |
|
1,050W |
|
NORMAL: 742W ECO: 617W LONG LIFE1: 410-588 |
|
|
LONG LIFE 2: 375-588W LONG LIFE 3: 349-588W SHUTTER: 82W |
|
|
STANDBY MODE [ECO]*1: 0.2W STANDBY MODE [NORMAL]: 3W |
|
|
STANDBY MODE (When the [QUICK STARTUP] function is enabled): Approx. 85 W |
|
|
*Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297 ft), |
|
|
ICE62087: 2008 Broadcast contents, |
|
|
Picture mode: Standard, Dynamic Contrast2 |
|
BTU value |
|
Max 3,584 BTU |
LCDpanel |
Panel size |
17.8 mm (0.7 in) diagonal (4:3 aspect ratio) |
|
Display method |
DLP™ chip × 1, DLP™ system |
|
Pixels |
786,432 (1024 × 768) × 1, total of 786,432 pixels |
Lens |
PT-RX110B/W |
Powered zoom/focus lenses (1.8–2.5:1), F 1.7–1.9, f 25.6–35.7 mm |
|
PT-RX110LB/LW |
Optional powered zoom/focus lenses and Šxed-focus lens |
Light source |
|
Laser Diode Laser class 1(Class3R for US models) |
|
|
Luminance life for set: 20,000 hours at half luminance (normal)/ |
|
|
24,000 hours at half luminance (Eco) |
|
|
* Temperature: 30°C (86°F), Altitude 700m (2,297 ft), Dust: 0.15mg/m3 |
|
|
Dynamic Contrast3 |
|
|
43,800 hours at constant luminance (LONG LIFE1) |
|
|
61,320 hours at constant luminance (LONG LIFE2) |
|
|
87,600 hours at constant luminance (LONG LIFE3) |
Screen size |
|
1.27– 15.24 m (50 – 600 inches) (4:3 aspect ratio) |
|
|
*1.27 – 5.08 m (50 – 200 inches) with the ET-DLE055 (4:3 aspect ratio) |
|
|
*2.54 – 7.62 m (100 – 350 inches) with the ET-DLE030 (4:3 aspect ratio) |
Brightness*3 |
|
10,400 lumens (Center)*2/ 10,000 lumens*3 |
|
|
10,000 lumens (Half luminance) (NORMAL) |
|
|
8,000 lumens (Half luminance) (ECO) |
|
|
3,900 lumens (Constant luminance) (LONG LIFE1) |
|
|
3,300 lumens (Constant luminance) (LONG LIFE2) |
|
|
2,700 lumens (Constant luminance) (LONG LIFE3) |
Center-to-corner uniformity*3 |
90% |
|
Contrast*3 |
|
10,000:1 (All White/All Black) (Dynamic Contrast3) |
Resolution |
|
1024 × 768 pixels (Input signals that exceed this resolution will be |
|
|
converted to 1024 x 768 pixels.) |
Scanning frequency |
HDMI/DVI-D |
fH: 15100kHz, fV: 24 - 120Hz, dot clock: 25 - 162 MHz |
|
|
525i (480i)*4, 625i (576i)*4, 525p (480p), 625p (576p), 750 (720)/60p, |
|
|
750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p, |
|
|
1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p, |
|
|
1125 (1080)/50p, VGA (640 x 480) - WUXGA (1920 x 1200) compatible |
|
|
with non-interlaced signals only |
|
RGB |
fH: 15100kHz, fV: 24 - 120Hz, dot clock: 20 - 162 MHz |
As of August 2016 |
2 / 1 8 |
SFD16M036
DLP™ Projector
PT-RX110B/RX110W/RX110LB/RX110LW
Scanning frequency |
YPBPR (YCBCR) |
525i (480i): |
fH 15.73 kHz; |
fV 59.9 Hz, |
|||
|
|
625i (576i): |
fH 15.63 kHz; |
fV 59.9 Hz, |
|||
|
|
525p (480p): |
fH 31.50 kHz; |
fV 60 Hz, |
|||
|
|
625p (576p): |
fH 31.25 kHz; |
fV 50 Hz, |
|||
|
|
750 (720)/60p: |
fH 45.00 kHz; |
fV 60 Hz, |
|||
|
|
750 (720)/50p: |
fH 37.50 kHz; |
fV 50 Hz, |
|||
|
|
1125 |
(1080)/60i: |
fH 33.75 kHz; |
fV 60 Hz, |
||
|
|
1125 |
(1080)/50i: |
fH 28.13 kHz; |
fV 50 Hz, |
||
|
|
1125 |
(1080)/25p: |
fH 28.13 kHz; |
fV 25 Hz, |
||
|
|
1125 |
(1080)/24p: |
fH 27.00 kHz; |
fV 24 Hz, |
||
|
|
1125 |
(1080)/24sF: |
fH 27.00 |
kHz; |
fV 48 |
Hz, |
|
|
1125 |
(1080)/30p: |
fH 33.75 |
kHz; |
fV 30 |
Hz, |
|
|
1125 |
(1080)/60p: |
fH 67.50 |
kHz; |
fV 60 |
Hz, |
|
|
1125 |
(1080)/50p: |
fH 56.25 |
kHz; |
fV 50 |
Hz |
Video/S-Video |
|
fH: 15.73 kHz, fV: 59.9 Hz [NTSC/NTSC4.43/PAL-M/PAL60] |
|
|||||||
|
|
|
fH: 15.63 kHz, fV: 50 Hz |
[PAL/PAL-N/SECAM] |
|
|
||||
Geometry correction range |
|
|
|
|
|
|
|
|
|
|
|
Only [KEYSTONE] used |
[KEYSTONE] and [CURVED] used together |
Only [CURVED] used |
|||||||
|
Projection |
Vertical |
Horizontal |
Vertical |
Horizontal |
|
|
|
|
|
|
lens Model |
keystone |
keystone |
keystone |
keystone |
Min. value |
Min. value |
Min. value |
Min. value |
|
|
No. |
correction |
correction |
correction |
correction |
of R2/L2 |
of R3/L3 |
of R2/L2 |
of R3/L3 |
|
|
|
angle α (°) |
angle β (°) |
angle α (°) |
angle |
β (°) |
|
|
|
|
|
Supplied lens/ |
±40 |
±15 |
±20 |
±15 |
0.9 |
1.7 |
0.5 |
1 |
|
|
ET-DLE170 |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
ET-DLE030* |
+5/-0 |
0 |
― |
― |
|
― |
― |
― |
― |
|
ET-DLE055 |
±22 |
±15 |
±8 |
±8 |
1.7 |
4.3 |
1 |
2.6 |
|
|
ET-DLE085 |
±22 |
±15 |
±8 |
±8 |
1.7 |
4.3 |
1 |
2.6 |
|
|
ET-DLE150 |
±40 |
±15 |
±20 |
±15 |
1.1 |
2.6 |
0.6 |
1.5 |
|
|
ET-DLE250 |
±40 |
±15 |
±20 |
±15 |
0.7 |
1.3 |
0.4 |
0.7 |
|
|
ET-DLE350 |
±40 |
±15 |
±20 |
±15 |
0.4 |
0.8 |
0.3 |
0.5 |
|
|
ET-DLE450 |
±40 |
±15 |
±20 |
±15 |
0.3 |
0.6 |
0.2 |
0.3 |
|
|
* Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves |
|||||||||
|
away from the screen. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[VERTICAL KEYSTONE] (viewed from the side) |
[HORIZONTAL KEYSTONE] (viewed from above) |
Screen |
Screen |
Vertical arc correction (viewed from the side) |
Horizontal arc correction (viewed from above) |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Projection distance |
|
|
|
Projection distance |
|||||
|
|
|
|
Arc radius |
|
|
|
Arc radius |
|||||
|
Screen |
|
|
|
Screen |
|
|||||||
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Arc center |
Arc center |
Screen |
Screen |
Projection distance |
Projection distance |
Arc radius |
Arc radius |
•When [GEOMETRY] is used, the focus of the entire screen may be lost as correction increases.
•Make the curved screen a circular arc shape with one part of a perfect circle removed.
•Adjustment range of the [GEOMETRY] items may not match the listed projection range depending on the projection lens. Use this projector within the projection range, otherwise the correction may not work.
As of August 2016 |
3 / 1 8 |
SFD16M036
DLP™ Projector
PT-RX110B/RX110W/RX110LB/RX110LW
Optical axis shift |
|
Vertical: +60%, -16%(powered), |
|
|
Horizontal: +30%, -10%(When using the ET-DLE085, +28%, -10 ) (powered) |
|
|
NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055. |
|
|
If using the ET-DLE030, the optical axis is fixed. |
Installation |
|
Ceiling/floor, front/rear, 360 degree free installation |
Terminals |
HDMI IN |
HDMI 19-pin × 1, Deep Color, compatible with HDCP, |
|
DVI-D IN |
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, |
|
|
for single link only |
|
RGB 1 IN |
BNC × 5 |
|
R, G, B |
R: 0.7 Vp-p, 75 ohms, |
|
|
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, |
|
|
B: 0.7 Vp-p, 75 ohms |
|
|
HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
|
Y, PB, PR (Y, CB, CR) |
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
|
Y,C |
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms |
|
Video |
1.0Vp-p, 75 ohms |
|
RGB 2 IN |
D-sub HD 15-pin (female) × 1 |
|
R, G, B |
R: 0.7 Vp-p, 75 ohms, |
|
|
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, |
|
|
B: 0.7 Vp-p, 75 ohms |
|
|
HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
|
Y, PB, PR(Y, CB, CR) |
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms |
|
SERIAL/MULTI |
|
|
PROJECTOR SYNC IN |
D-sub 9-pin (female) × 1 for external control (RS-232C compliant) |
|
SERIAL/MULTI |
|
|
PROJECTOR SYNC OUT |
D-sub 9-pin (male) x 1 for link control |
|
REMOTE 1 IN |
M3 jack x 1 for wired remote control |
|
REMOTE 1 OUT |
M3 jack x 1 for link control (for wired remote control) |
|
REMOTE 2 IN |
D-sub 9-pin (female) x1 for external control (parallel) |
|
LAN/DIGITAL LINK |
RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control) |
|
|
connection, 100Base-TX, compliant with PJLink™(Class 1) |
|
|
Deep Color, HDCP |
Power cord length |
|
3.0 m (9 ft 10 in) |
Cabinet materials |
|
Molded plastic |
Dimensions (W × H × D) PT-RX110B/RX110W |
498 x 200*5 x 581mm |
|
|
|
(19-19/32 x 7-7/8*5 x 22-7/8in ) with supplied lens |
|
PT-RX110LB/RX110LW |
498 x 200*5 x 538 mm |
|
|
(19-19/32 x 7-7/8*5 x 21-3/16in) without lens |
Weight |
PT-RX110B/RX110W |
Approx. 23.2kg (51.1lbs) with supplied lens |
|
PT-RX110LB/RX110LW |
Approx. 22.4kg (49.4lbs) without lens |
Operation noise |
|
41 dB |
Operating temperature |
|
0 – 45 °C (32 –113 °F) *6 |
Operating humidity |
|
10%– 80% (no condensation) |
As of August 2016 |
4 / 1 8 |
SFD16M036
DLP™ Projector
PT-RX110B/RX110W/RX110LB/RX110LW
Remote control unit |
|
Power supply |
3 V DC (R03/AAA type battery × 2) |
Operation range |
Approx. 30 m (98 ft 5 in) when operated from directly in front of the |
|
signal receptor |
Dimensions (W × H × D) |
48 × 145 × 27 mm (1-57/64 × 5-45/64 × 1-3/64 in) |
Weight*7 |
Approx. 102 g (3.6 oz) including batteries |
Supplied accessories |
|
|
Power cord with secure lock (× 1) (× 2 for EU models) |
|
Wireless/wired remote control unit (× 1) |
|
Batteries for remote control (R03/AAA type × 2) |
|
Software CD-ROM (Logo Transfer Software, Multi Monitoring |
|
& Control Software) (× 1) |
|
Lens Mount Cover (× 1) |
|
Lens cover (× 1) (Only models with lens) |
Optional accessories |
|
Digital interface box |
ET-YFB100G |
Digital LINK Switcher |
ET-YFB200G |
Zoom lens (0.8–1.0:1) |
ET-DLE085 |
Zoom lens (1.3 – 2.0:1) |
ET-DLE150 |
Zoom lens (1.8 – 2.5:1) |
ET-DLE170 (same as supplied lens) |
Zoom lens (2.4 – 3.7:1) |
ET-DLE250 |
Zoom lens (3.7 – 5.6:1) |
ET-DLE350 |
Zoom lens (5.5 – 8.9:1) |
ET-DLE450 |
Fixed-focus lens (0.38:1) |
ET-DLE030 |
Fixed-focus lens (0.8:1) |
ET-DLE055 |
Ceiling mount bracket |
ET-PKD120H (for high ceilings) |
|
ET-PKD120S (for low ceilings) |
High-ceiling mount bracket |
ET-PKD130H |
(6-axis adjustment mechanism) |
|
Attachment for ceiling mount bracket |
ET-PKD130B |
Geometry Manager Pro Upgrade kit |
ET-UK20 |
Auto Screen Adjustment Upgrade kit |
ET-CUK10 |
Early Warning Software |
ET-SWA100* |
* The symbol at the end of the part number will vary depending on the type of license.
*1 When the STANDBY MODE is set to Eco, network functions such as power on over the LAN will not operate.
*2 The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by the ISO/IEC 21118:2012 international standards.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*5 with legs at shortest position.
*6 Limits the luminance when used in locations from 0m to 2,700m (0ft to 8,858ft) above sea level at ambient temperatures of 35°C (95°F) or higher, or from 2,700m to 4,200m (8,858ft to 13,780ft) above sea level at ambient temperatures of 25°C (77°F) or higher.
*7 Average value. May differ depending on models.
As of August 2016 |
5 / 1 8 |
SFD16M036
DLP™ Projector
PT-RX110B/RX110W/RX110LB/RX110LW
Dimensions
|
|
269 -19/32) |
|
|
|
|
|
|
(10 |
|
|
580.8 |
(22-7/8) |
|
|
538 |
(21-3/16) |
|
|
269 |
-19/32) |
|
|
|
|
|
(10 |
|
|
|
249 (9-13/16) |
28 |
(1-3/32) |
42.8 |
(1-11/16) |
|
|
115.5 (4-9/16) |
|
|
|
|
221 (8-11/16) |
|
|
|
|
442 (17-13/32)
498 (19-19/32)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
181 |
(7-1/8) |
96.5 -13/16) |
|
|
|
(3 |
|
19 |
(3/4) |
4 |
(5/32) |
200 (7-7/8)
432 (17)
444 (15/32)
457 (18)
Terminals
1 |
|
2 |
3 |
4 |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6
5 |
|
|
|
1 |
REMOTE 1 |
INPUT |
|
|
|
2 |
REMOTE 1 |
OUTPUT |
|
|
|
|
|
|||
|
|
|
|
3 |
REMOTE 2 |
INPUT |
|
|
|
|
4 |
SERIAL/MULTI PROJECTOR SYNC INPUT |
|
|
|
|
|
5 |
SERIAL/MULTI PROJECTOR SYNC OUTPUT |
|
|
|
|
|
6 |
RGB 1 INPUT |
|
|
|
|
|
7 |
RGB 2 INPUT |
|
|
|
|
|
8 |
DVI-D INPUT |
|
7 |
8 |
9 |
10 |
9 |
HDMI INPUT |
|
|
|
|
|
10 |
LAN/DIGITAL LINK TERMINAL |
As of August 2016 |
6 / 1 8 |
SFD16M036