Panasonic PT-RS20KU User Manual

PEC

ILE

Product Number :

Product Name :

PT-RS20K

3-Chip DLP™Projector

As of October 2017. Specifications and appearance are subject to change without notice.

SFD17M002

1/18

3-Chip DLP™ Projector

PT-RS20K

Specifications

Main unit

Power supply The light output will decrease to approximately 1/2 when using the projector with AC 100V to AC 120V [9.6A]. Power consumption 4 W with Standby Mode set to Normal) 1,217W (Normal Mode), 972 W (Eco Mode) Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297ft),

BTU value Max 5,159 BTU DLP™ chip Panel size 24.1 mm (0.95 inches) diagonal (4:3 aspect ratio) Display method DLP™ chip × 3, DLP™ projection system Pixels 4,410,000 (1400 x 1050 x 3) pixels Refresh rate 120 Hz* Lens Optional (no lens included with this model), powered zoom, powered focus lens Light source Laser Diode (Laser class: Class 1)*Class 3R for North America. Illumination life of set Varies depending on operation mode setting. 20,000 hours at half luminance (Normal) 24,000 hours at half luminance (Eco) * IEC62087: 2008 Broadcast contents, Dynamic contrast [3] (NORMAL/ECO Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast [3] Under conditions of 0.15 mg/m3 of particulate matter Screen size (diagonal) 1.78–25.4 m (70–1,000 in) with 4:3 aspect ratio

1.78–15.24 m (70–600 in) with the ET-D75LE8, 4:3 aspect ratio

3.05–15.24 m (120–600 in) with the ET-D75LE95, 4:3 aspect ratio Brightness 21,000 lm (Center)*3*5 / 20,000 lm (Normal)*4* Center-to-corner uniformity

90 % Contrast*3 20,000:1 (Full On/Full Off, Dynamic Contrast Mode: 3) Resolution 1400 x 1050 pixels Scanning frequency Video/YC fH:15.73KHz fV:59.94Hz, fH:15.63KHz fV:50Hz RGB • Resolution: 640 x 400 pixels to 1920 x 1200 pixels

• Dot clock frequency: 162MHz or less

• PIAS (Panasonic Intelligent Auto Scanning) YPBPR(YCBCR) • Resolution: 480i/576i to 1920 x 1080 pixels

• Dot clock frequency: 148.5MHz or less

• The SYNC/HD and VD terminals do not support 3 value SYNC. DVI • Moving image signal resolution: 480i* Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)

• Dot clock frequency: 25 MHz to 162 MHz HDMI/DIGITAL LINK • Moving image signal resolution: 480i* Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace)

• Dot clock frequency: 25 MHz to 162 MHz SDI SD-SDI signal HD-SDI signal 3G-SDI signal Optical axis shift Vertical (from center of screen) ±50 % (±40 % with ET-D75LE6, +67 % – +71 % with ET-D75LE95) (powered)

NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.

Horizontal (from center of screen)

AC 200V-240V, 7.7A, 50/60Hz

1,510 W (1,525 VA [AC200V]) (0.3 W with Standby Mode set to Eco*1,

IEC627087: 2008 Broadcast contents, Picture mode: Standard, Dynamic contrast [2]

/576i*6 to 1920x1080

±30 % (±20 % with ET-D75LE6, ±8 % with ET-D75LE95) (powered)

Keystone correction range

Projection

lens Model

No.

ET-D75LE6

ET-D75LE8 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE50

ET-D75LE95*

When using the optional Upgrade Kit (Model No.: ET-UK20)

Projection

lens Model

No.

ET-D75LE6

ET-D75LE8 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE50

ET-D75LE95*

Only [KEYSTONE] used [KEYSTONE] and [CURVED] used together Only [CURVED] used

Vertical keystone

correction angle

+5 / -0

Vertical keystone

correction angle

+5 / -0

Horizontal keystone

α (°)

± 28 ± 40 ± 40 ± 40 ± 40 ± 40 ± 22

α (°)

± 28 ± 45 ± 40 ± 40 ± 45 ± 45 ± 22

correction angle

Only [KEYSTONE] used*

Horizontal keystone

correction angle

β (°)

± 15 ± 15 ± 15 ± 15 ± 15 ± 15 ± 15

β (°)

± 15 ± 40 ± 40 ± 40 ± 40 ± 40 ± 15

Vertical keystone

correction angle

Vertical keystone

correction angle

Horizontal keystone

α (°)

± 10 ± 20 ± 20 ± 20 ± 20 ± 20

α (°)

± 10 ± 20 ± 20 ± 20 ± 20 ± 20

correction angle

β (°)

± 10 ± 15 ± 15 ± 15 ± 15

± 8

± 15

± 8

[KEYSTONE] and [CURVED] used together*

Horizontal keystone

correction angle

β (°)

± 10 ± 15 ± 15 ± 15 ± 15 ± 15

± 8

Min. value of

R2/L2

1.6

0.2

1.1

0.9

0.6

0.4

2.0

Min. value of

R2/L2

1.2

0.2

0.9

0.7

0.5

0.3

1.5

Min. value of

3/L3

3.9

0.4

2.6

1.7

1.2

0.7

4.9

Min. value of

3/L3

3.0

0.3

2.0

1.3

0.9

0.5

3.7

Min. value of

R2/L2

Only [CURVED] used

Min. value of

R2/L2

Min. value of

0.9

0.2

0.6

0.5

0.4

0.2

1.2

0.7

0.1

0.5

0.4

0.3

0.2

0.9

R3/L3

2.3

0.3

1.5

1.0

0.7

0.4

2.9

Min. value of

R3/L3

1.7

0.2

1.1

0.7

0.5

0.3

2.2

As of October 2017 2/18

SFD17M002

3-Chip DLP™ Projector

PT-RS20K

Keystone correction range

[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)

Screen

Arc center

Screen

Projection distance Arc radius

Screen

Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)

Projection distance Arc radius

Screen

Arc center

Screen

Projection distance Arc radius

Installation Ceiling/floor, front /rear, free 360-degree installation

Terminals RGB1 IN BNC × 5

R,G,B R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

Y/C Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms

VIDEO IN BNC × 1, 1.0 Vp-p, 75 ohms

RGB2 IN D-sub HD 15-pin (female) × 1

R,G,B R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

DVI-D IN DVI-D 24-pin ×1

Single link, DVI 1.0 compliant, HDCP compatible

HDMI IN HDMI 19-pin x1

HDCP compatible, Deep Color compatible

SDI IN 1 BNC × 1 SD-SDI signal SMPTE ST 259 compliant

HD-SDI signal SMPTE ST 292 compliant

3G-SDI signal SMPTE ST 424, 425-2 compliant

Dual link HD-SDI (LINK A) signal SMPTE ST 372 compliant

Dual link 3G-SDI (Link 1) signal SMPTE ST 425-3 compliant

SDI IN 2 BNC × 1 SD-SDI signal SMPTE ST 259 compliant

HD-SDI signal SMPTE ST 292 compliant

3G-SDI signal SMPTE ST 424, 425-2 compliant

Dual link HD-SDI (LINK B) signal SMPTE ST 372 compliant

Dual link 3G-SDI (Link 2) signal SMPTE ST 425-3 compliant

As of October 2017 3/18

SFD17M002

3-Chip DLP™ Projector

PT-RS20K

Terminals DIGITAL LINK RJ-45 HDBaseT™ compliant, HDCP compatible, Deep Color compatible 3D SYNC1 IN/OUT / MULTI PROJECTOR SYNC IN BNC × 1, IN : TTL Hi-z OUT : TTL max10mA 3D SYNC2 OUT / MULTI PROJECTOR SYNC OUT BNC × 1, TTL max10mA SERIAL IN D-sub 9-pin × 1 for external control (RS-232C compliant) SERIAL OUT D-sub 9-pin × 1 for link control REMOTE 1 IN M3 jack × 1 for wired remote control REMOTE 1 OUT M3 jack × 1 for link control REMOTE 2 IN D-sub 9-pin × 1 for external control (parallel) DIGITAL LINK/LAN RJ-45 × 1 for network connection, 100Base-TX PJLink™ (class 2) compatible, Art-Net compatible DC OUT 5V USB connector (type A) x 2 for power supply only (DC 5V, Max 2A) Power cord length 3.0 m(9 ft 10 in) Cabinet materials Molded plastic Dimensions (W × H × D) 598 × 270 × 725 mm (23 17/32˝ x 10 5/8˝ x 28 17/32˝ ) (not including protruding parts)

Weight* Operation noise*

Approximately 49kg (108 lbs) (not including lens)

46dB

Operating environment Operating temperature: 0–50 °C (32–122 °F)*10; Operating humidity: 10–80 % (no condensation)

Remote control unit

Power supply DC 3 V (AAA/R03/LR03 battery × 2) Operation range Approx. 30 m (98 ft 5 in) when operated from directly in front of the signal receptor Dimensions (W × H × D) 47.5 x 181.5 x 27.5 mm (1-7/8" x 7-5/32" x 1-3/32") Weight Approx. 150g (5.3 ozs.) (including batteries)

Supplied accessories

Power cord with secure lock (×2) Wireless/wired remote control unit (×1) Batteries for remote control (AA/R6 type ×2) Lens hole cover (× 1) Lens drop-prevention screw (× 1)

Optional accessories

Zoom lens (1.01–1.19:1) ET-D75LE6 Zoom lens (1.41–1.81:1) ET-D75LE10 Zoom lens (1.80–2.61:1) ET-D75LE20 Zoom lens (2.60–5.05:1) ET-D75LE30 Zoom lens (5.00–7.99:1) ET-D75LE40 Zoom lens (7.95–14.9:1) ET-D75LE8 Fixed-focus lens (0.752:1) ET-D75LE50 Fixed-focus lens (0.394:1) ET-D75LE95

Ceiling Mount Bracket (for High ceilings) Ceiling Mount Bracket (Projector Mount Bracket)

ET-PKD520H

ET-PKD520B

Ceiling Mount Bracket (for Low ceilings)

ET-PKD520S

Stepping Motor kit ET-D75MKS10 Frame ET-PFD510 Upgrade kit ET-UK20

Auto Screen Adjustment Upgrade Kit (PC)

ET-CUK10P Auto Screen Adjustment Upgrade Kit ET-CUK10 Lens Fixed Attachment ET-PLF10 Digital Interface Box ET-YFB100G DIGITAL LINK switcher ET-YFB200G

Compatible Software

Logo Transfer Software Smart Projector Control(iOS/android) Early Warning Software(Basic license/3-year license)(ET-SWA100series*)*The sufx of the Model No. differs according to the license type.

*1 When Standby Mode is set to ECO, network functions such as power on over LAN will not operate. Additionally, only certain commands can be

received for external control using the serial terminal. *2 Refresh rate varies depending on scanning frequency. *3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *4 The value of the light output at the center region of the projected image is extracted based on the light output measurement method dened by

the ISO/IEC 21118:2012 international standards. *5 In AC200V, When using a projection lens other than ET-D75LE95. *6 Pixel-Repetition signal(dot clock frequency 27.0MHz) only *7 Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves away from the screen. *8 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be made exceeding total of 55°. *9 Average value. May differ depending on the actual unit. *10 Operating temperature is 0–45 °C (32–113 °F) when used in locations from 1,400 m to 4,200 m (4,593 ft to 13,779 ft) above sea level.

When the [PROJECTOR SETUP] menu Ѝ [OPERATION SETTING] Ѝ [OPERATING MODE] is set to [NORMAL], and the operating environment

temperature exceeds the following value, the light output may be reduced to protect the projector.

•When using the projector at an altitude lower than 2,700m (8,858') above sea level: 35°C (95°F)

•When using the projector at an altitude between 2,700m (8,858') and 4,200m (13,780') above sea level: 25°C (77°F)

As of October 2017 4/18

SFD17M002

3-Chip DLP™ Projector

Dimensions

Adjustable feet

725

[28-17/32]

298

[25/32]

Adjustable feet

Position of screw holes to fix projector and adjustable feet

250

[9-27/32]

250

[9-27/32]

[11-23/32]

145

[5-23/32]

110

[4-11/32]

145

[5-23/32]

PT-RS20K

135.5

[5-11/32]

Screw holes to fix the projector (M6-30)

Use a torque screwdriver or Allen torque wrench to tighten the fixing screws to their specified tightening torques. Do not use elector impact screwdrivers.

110

[4-11/32]

142

[5-19/32]

516

[20-5/16]

598

[23-17/32]

299

[11-25/32]

258

[10-5/32]

131

[5-5/32]

270

[1-7/8]

644

[25-11/32]

unit : mm (inch) NOTE: This illustration is not drawn to sc ale.

307

[10-5/8]

[12-3/32]

As of October 2017 5/18

SFD17M002

3-Chip DLP™ Projector

Terminals

䙵䙺䙻䙶䙷䙸䙹䙼

Power cord

䷿䙽䙾一丁丂

PT-RS20K

1 Remote 1 input

2 Remote 1 output

3 Remote 2 input

Serial input

Serial output

MULTI PROJECTOR SYNC IN 3D SYNC 1 IN/OUT

MULTI PROJECTOR SYNC OUT 3D SYNC 2 OUT

DC output 1/DC output 2

SDI 1 input/SDI 2 input

RGB 1 input

11 RGB 2 Input

DVI-D input

HDMI input

LAN/DIGITAL LINK connector

For 200V - 240V

At projector

At power outlet At power outlet At power outlet

For 200V - 240V For 200V - 240V

At projector At projector

At power outlet At power outlet

At projector

AC IN terminal

For 200V - 240V

At projector

2P/3W 15 A 250 V

For 200V - 240V

At projector

At power outlet

For 110V - 120V

At projector

At power outlet

(For Taiwan)

At projector

Power outlets that can be used

2P/3W 15 A 250 V

2P/3W 15 A 125 V

This projector supports AC100 V to AC120 V, and AC 200 V to AC 240 V as the power supply. A grounding outlet supporting 15 A is required with either voltage. The shape of the usable outlet differs depending on the power supply. Following illustrations are examples.

As of October 2017 6/18

SFD17M002

+ 12 hidden pages