Panasonic PT-RQ50K User Manual

Page 1
Operating Instructions
Functional Manual
DLP™ Projector
Model No.
The projection lens is sold separately.
PT-RQ50K
Commercial Use
Thank you for purchasing this Panasonic product.
■ This manual is common to all the models.
zfor USA, Canada, EU countries, Korea, Taiwan
PT-RQ50K
zfor India
PT-RQ50KD
zfor other countries or regions with power cord for 100 V - 120 V
PT-RQ50KX
zfor other countries or regions without power cord for 100 V - 120 V
PT-RQ50KE
■ Before operating this product, please read the instructions carefully and save this manual
for future use.
Before using this product, be sure to read “Read this rst!” (x pages 5 to 14).
ENGLISH
DPQP1291ZA/X1
Page 2
Contents
Contents
Read this rst! 5
Chapter 1 Preparation
Precautions for use 18
Intended use of the product Installation and handling of the laser product
(for USA and Canada)
Cautions when transporting Cautions when installing Cautions when setting up the projector Security Notes regarding the wireless LAN DIGITAL LINK Art-Net Application software supported by the projector
Storing Disposal Cautions on use Accessories Optional accessories
About your projector
Remote control Projector body Names and functions of the Interface Board
Preparing the remote control
Inserting and removing the batteries When using the multiple projectors Connecting the remote control to the projector
with a cable
18
18 18 18 21 23 24 25 25
25 26 26 26 27 28
29
29 31 35
37
37 37
38
Chapter 2 Getting Started
Setting up 40
Usable outlet Installation mode Interface Board Projected image and throw distance Adjusting adjustable feet
Attaching/removing the projection lens
(optional)
Attaching the projection lens Removing the projection lens
40 40 42 42 48
49
49 50
Connecting 52
Before connecting Connecting example: AV equipment Connecting example: Computers Connecting example using DIGITAL LINK Connecting example when using the
contrast synchronization function/shutter synchronization function
52
Chapter 3 Basic Operations
Switching on/off the projector 59
Connecting the power cord Power indicator Switching on the projector When the initial setting screen is displayed Making adjustments and selections Switching off the projector
Projecting
Selecting the input signal Adjusting the focus, zoom, and lens shift Adjusting the focus balance Executing the lens calibration Moving the projection lens to the home position
Lens shift range Adjusting the lens mounter when the focus is
Using the USB memory
Notes on use USB memory that can be used with the
Attaching the USB memory Removing the USB memory
Operating with the remote control
Using the shutter function Using the on-screen display function Using the automatic setup function Switching the image aspect ratio Using the function button Displaying internal test pattern Using the status function Setting ID number of the remote control
69
73
unbalanced
projector
60
74
75
78
78
Chapter 4 Settings
52 54 55
56
59
61
62 67
68
69
71
72
73
78
78
78
79
79
79 80 80
80
81
81
81
2 - ENGLISH
Menu navigation 84
Navigating through the menu Main menu Sub-menu
85
86
84
Page 3
Contents
[PICTURE] menu
[PICTURE MODE] [CONTRAST] [BRIGHTNESS] [COLOR] [TINT] [COLOR TEMPERATURE] [GAMMA] [SYSTEM DAYLIGHT VIEW] [SHARPNESS] [NOISE REDUCTION] [DYNAMIC CONTRAST] [COLOR SPACE] [SYSTEM SELECTOR] sRGB-compliant video
[POSITION] menu
[SHIFT] [ASPECT] [ZOOM] [GEOMETRY] [CONVERGENCE]
[ADVANCED MENU] menu
[DIGITAL CINEMA REALITY] [BLANKING] [EDGE BLENDING] [FRAME RESPONSE] [FRAME DELAY] [RASTER POSITION]
[DISPLAY LANGUAGE] menu
Changing the display language
[DISPLAY OPTION] menu
[COLOR MATCHING] [SCREEN SETTING] [AUTO SIGNAL] [AUTO SETUP] [BACKUP INPUT SETTING] [SIMUL INPUT SETTING] [SLOT IN] [DIGITAL LINK IN] [ON-SCREEN DISPLAY] [MENU MODE] [BACK COLOR] [STARTUP LOGO] [UNIFORMITY] [SHUTTER SETTING] [FREEZE] [WAVEFORM MONITOR] [CUT OFF]
89
89 89 90 90 90 90 92 94 94 94 94 96 96 97
98
98 98
99 100 105
106
106 106 107 109 109
110
111
111
112
112 114 114 114 115 117
117 131 133 135 136 136 137 138 140 140 141
[PROJECTOR SETUP] menu
[PROJECTOR ID] [PROJECTION METHOD] [LENS] [OPERATION SETTING] [LIGHT OUTPUT] [BRIGHTNESS CONTROL] [NO SIGNAL SETTING] [INITIAL STARTUP] [STARTUP INPUT SELECT] [DATE AND TIME] [SCHEDULE] [MULTI PROJECTOR SYNC] [RS-232C] [REMOTE2 MODE] [FUNCTION BUTTON] [STATUS] [INFO MONITOR SETTING] [DATA CLONING] [SAVE ALL USER DATA] [LOAD ALL USER DATA] [INITIALIZE] [FIRMWARE UPDATE] [SERVICE PASSWORD]
[TEST PATTERN] menu
[TEST PATTERN]
[SIGNAL LIST] menu
Registering new signals Renaming the registered signal Deleting the registered signal Protecting the registered signal Expanding signal lock-in range Sub memory
[SECURITY] menu
[SECURITY PASSWORD] [SECURITY PASSWORD CHANGE] [CONTROL DEVICE SETUP] [CONTROL DEVICE PASSWORD CHANGE]
[NETWORK] menu
[DIGITAL LINK MODE] [DIGITAL LINK STATUS] [WIRED LAN] [WIRELESS LAN] [PROJECTOR NAME] [NETWORK CONTROL] [NETWORK STATUS] [DIGITAL LINK MENU] [Art-Net SETUP] [Art-Net CHANNEL SETTING] [Art-Net STATUS]
144
170
173
189
143
157
166
167
178
178
181
182
184
185
191
192
192
195
196
143
143
154
158
161
165
165
168
172
172
176
178
178
180
180
181
182
182 182 183 183
185
185 185
191
191
193
193
194
194
195
ENGLISH - 3
Page 4
Contents
Chapter 5 Operations
Network connection 198
Connecting via wired LAN Connecting via wireless LAN
Web control function
Computer that can be used for setting Accessing from the web browser
Using the information monitor function
Screen mode Top menu Sub-menu Basic operation procedure in the menu
operation mode [USER VIEW] menu [SETUP] menu [STATUS] menu Error notication mode
Using the data cloning function
Copying the data to another projector via LAN
Copying the data to another projector using
USB
Updating the rmware
Updating the rmware via LAN Updating the rmware using the USB memory
198 200
202
202 202
229
229 229 229
230 230 231 235 237
239
239
241
243
243
248
Chapter 6 Maintenance
Light source/temperature indicators 251
When an indicator lights up
Maintenance
Before maintenance Maintenance
Troubleshooting Self-diagnosis display
251
253
253 253
254 256
Chapter 7 Appendix
Technical information 259
PJLink protocol Using Art-Net function Control commands via LAN <SERIAL IN>/<SERIAL OUT> terminal <REMOTE 2 IN> terminal List of compatible signals
Specications Dimensions Installing the Interface Board
Before installing or removing How to install the Interface Board How to remove the Interface Board
Index
259 261 266 269 273 274
290 293 294
294 294 295
296
4 - ENGLISH
Page 5
Read this rst!
Read this rst!
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance to rain
or moisture.
This device is not intended for use in the direct eld of view at visual display workplaces. To avoid incommoding reexions at visual display workplaces this device must not be placed in the direct eld of view.
The equipment is not intended for used at a video workstation in compliance BildscharbV.
The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied
service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing-
type mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you are
unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug.
WARNING:
This equipment is compliant with Class A of CISPR32. In a residential environment this equipment may cause radio interference.
(for Taiwan)
WARNING:
This equipment complies with the Class A standard of CISPR32. This is Class A information technology equipment that may cause radio frequency interference when used in a residential environment, in which the user will be required to take certain appropriate countermeasures.
CAUTION: To assure continued compliance, follow the attached installation instructions. This includes using
the provided power cord and shielded interface cables when connecting to computer or peripheral
devices. Also, any unauthorized changes or modications to this equipment could void the user’s
authority to operate this device.
This is a device to project images onto a screen, etc., and is not intended for use as indoor lighting in a domestic environment.
Directive 2009/125/EC
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
ENGLISH - 5
Page 6
Read this rst!
WARNING: RISK OF ELECTRIC SHOCK. DON’T OPEN
Indicated on the projector
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
WARNING: Do not look at the light emitted from the lens while the projector is being used.
Indicated on the projector
This projector is designed for commercial use.
Notice on laser (for USA and Canada)
This projector is the Class 3R laser product that complies with IEC 60825-1:2007.
HAZARD DISTANCE: REFER TO THE OPERATING INSTRUCTIONS.
DISTANCE DU RISQUE : CONSULTEZ LE MANUEL D’UTILISATION.
GEFÄHRDUNGSABSTAND: BEACHTEN SIE DIE BEDIENUNGSANLEITUNG.
ОПАСНОЕ РАССТОЯНИЕ: СМ. ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ.
위험 거리 : 사용설명서를 참조하십시오.
For North America
This product is in conformity with
performance standards for laser
products under 21 CFR 1040,
except with respect to those
characteristics authorized by
Variance Number 2019-V-3842
effective on September 11,2019.
DPQT1466ZA
6 - ENGLISH
TQFX608
DANGER-
CLASS 4 LASER RADIATION WHEN OPEN AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION DANGER-
RAYONNEMENT LASER DE CLASSE 4 - EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU RAYONNEMENT DIRECT OU DIFFUS DES YEUX OU DE LA PEAU
(Inside of product)
Page 7
Read this rst!
(for Taiwan)
This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.
(for India)
This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.
HAZARD DISTANCE: REFER TO THE OPERATING INSTRUCTIONS.
1
類雷射產品
DISTANCE DU RISQUE : CONSULTEZ LE MANUEL D’UTILISATION.
GEFÄHRDUNGSABSTAND: BEACHTEN SIE DIE BEDIENUNGSANLEITUNG.
ОПАСНОЕ РАССТОЯНИЕ: СМ. ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ.
위험 거리 : 사용설명서를 참조하십시오.
(for other countries or regions)
This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.
HAZARD DISTANCE: REFER TO THE OPERATING INSTRUCTIONS.
DISTANCE DU RISQUE : CONSULTEZ LE MANUEL D’UTILISATION.
GEFÄHRDUNGSABSTAND: BEACHTEN SIE DIE BEDIENUNGSANLEITUNG.
ОПАСНОЕ РАССТОЯНИЕ: СМ. ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ.
위험 거리 : 사용설명서를 참조하십시오.
CAUTION: Use of controls or adjustments or performance of procedures other than those specied herein
may result in hazardous radiation exposure.
CAUTION (North/Middle/South America)
This equipment is equipped with a three-pin grounding-type power plug. Do not
remove the grounding pin on the power plug. This plug will only t a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.
Do not remove
ENGLISH - 7
Page 8
Read this rst!
WARNING (USA and Canada)
fNot for use in a computer room as dened in the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
fFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
fFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily
accessible.
NOTIFICATION (Canada)
This class A digital apparatus complies with Canadian ICES-003.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
FCC NOTICE (USA)
Supplier’s Declaration of Conformity
Model Number: PT-RQ50K / PT-RQ50KX Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: Two Riverfront Plaza, Newark, NJ 07102-5490 General Contact: http://www.panasonic.com/support Projector Contact: https://panasonic.net/cns/projector/
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Warning:
To assure continued compliance, follow the attached installation instructions. This includes using the provided power cord and shielded interface cables when connecting to computer or peripheral devices. Also, any
unauthorized changes or modications to this equipment could void the user’s authority to operate this device.
Importer’s name and address within the European Union Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany
8 - ENGLISH
Page 9
Read this rst!
rHazard distance (IEC 62471-5:2015)
The distance from the projection lens surface, at which the level of exposure has reached the level of the
applicable Exposure Limit Value, is known as the hazard distance (HD) or safety distance. Do not look into the projected light from inside the hazard distance (within RG3 range). The eyes may be damaged
by the direct irradiation. It is considered to be safe to look into the projected light from outside the hazard distance
(within RG2 range).
RG2
D1
D2
RG3
HD
D3
RG2
D4
HD
RG3
rRisk group
The combination of the projector and the projection lens is categorized as the risk group 2 when the hazard
distance is less than 1 m (39-3/8"). It is categorized as the risk group 3 when the hazard distance exceeds 1 m (39-3/8"), and it will be for professional use instead of consumer use.
In case of risk group 3, there is a possibility of damaging the eyes by direct irradiation when looking into the
projection light from inside the hazard distance (within RG3 range).
In case of risk group 2, it can be used safely without damaging the eyes in any condition. Combinations with any projection lens are categorized as risk group 3 for this projector.
Each dimension inside the hazard distance (within RG3 range) for combination with projection lens which the hazard distance exceeds 1 m (39-3/8") is as follows.
(Unit: m)
Projection lens
Model No.
ET-D3QW300 1.8 0.280 0.280 0.529 0.529 ET-D3QS400 2.3 0.290 0.290 0.548 0.548 ET-D3QT500 3.9 0.304 0.304 0.574 0.574 ET-D3QT600 4.1 0.278 0.278 0.526 0.526 ET-D3QT700 5.5 0.270 0.270 0.509 0.509 ET-D3QT800 8.4 0.289 0.289 0.545 0.545
HD
*1
D1
*2
D2
*2
D3
*2
D4
*2
*1 HD: Hazard Distance *2 The values of D1 to D4 will change in accordance with the lens shift amount. Each value in the table is the maximum value.
Note
fThe value in the table is based on IEC 62471-5:2015.
ENGLISH - 9
Page 10
Read this rst!
WARNING:
rPOWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately.
Continued use of the projector in these conditions will result in re or electric shock, or will cause visual
impairment.
fIf foreign objects or water get inside the projector, cut off the power supply. fIf the projector is dropped or the cabinet is broken, cut off the power supply. fIf you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord, the power plug, or the power connector.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
fDo not damage the power cord, make any modications to it, disassemble it, place it near any hot objects,
bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. Consult an Authorized Service Center for any repairs to the power cord, the power plug, or the power connector that might be necessary.
Do not use anything other than the provided power cord.
Failure to observe this will result in electric shocks or re. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Completely insert the power plug into the wall outlet.
If the plug is not inserted correctly, electric shocks or overheating will result.
fDo not use plugs which are damaged or wall outlets which are coming loose from the wall.
Fully attach the power connector (projector-side) to the <AC IN> terminal.
A power connector that is not completely attached may result in res caused by electric shocks or heat
generation.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Use an outlet supporting 30 A independently when using the projector with 200 V to 240 V alternating current. Use an outlet supporting 15 A independently when using the projector with 100 V to 120 V alternating current.
Using an outlet together with another device may result in res due to heat generation.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a re.
fIf dust builds up on the power plug, the resulting humidity can damage the insulation. fIf not using the projector for an extended period of time, pull the power plug out from the wall outlet.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
rON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam.
Using the projector under such conditions will result in re, electric shocks or deterioration of components. Oil
may also distort the plastic and the projector could fall such as when mounted on the ceiling.
Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result.
10 - ENGLISH
Page 11
Read this rst!
WARNING:
Do not install the projector in a location where people pass through.
People may bump into the projector or trip on the power cord, which may result in re, electric shock, or injury.
Do not cover the intake/exhaust vents or place anything within 500 mm (19-11/16") of them.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
fDo not place the projector in narrow, badly ventilated places. fDo not place the projector on cloth or papers, as these materials could be drawn into the intake vent.
Do not look at or place your skin into the light emitted from the lens while the projector is being used.
Do not enter the projection luminous ux using an optical device (such as magnier or mirror).
Doing so can cause burns or loss of sight.
fStrong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light. fBe especially careful not to let young children look into the lens. In addition, turn off the power and switch
off the main power when you are away from the projector.
Do not project an image with the lens cover of the projection lens (optional) attached.
Doing so can cause re.
Never attempt to remodel or disassemble the projector.
High voltages can cause re or electric shocks.
fFor any inspection, adjustment and repair work, please contact an Authorized Service Center.
Do not touch the top surface of the projector during use.
Doing so may result in burns, as the top surface is hot during use and for a while after use.
Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the
projector.
fDo not place containers of liquid or metal objects near the projector. fIf liquid enters inside of the projector, consult your dealer. fParticular attention must be paid to children.
Installation work such as mounting the projector on the ceiling should only be carried out by a qualied
technician.
If installation is not carried out and secured correctly, it can cause injury or accidents, such as electric shocks.
rACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.
fDo not use unspecied batteries. fDo not charge dry cell batteries. fDo not disassemble dry cell batteries. fDo not heat the batteries or place them into water or re. fDo not allow the + and – terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins.
fDo not store or carry batteries together with metallic objects. fStore the batteries in a plastic bag and keep them away from metallic objects. fMake sure the polarities (+ and –) are correct when inserting the batteries. fDo not use a new battery together with an old battery or mix different types of batteries. fDo not use batteries with the outer cover peeling away or removed.
If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.
fBattery uid on your skin or clothing could result in skin inammation or injury.
Rinse with clean water and seek medical advice immediately.
fBattery uid coming in contact with your eyes could result in loss of sight.
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Remove the depleted batteries from the remote control promptly.
fLeaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.
ENGLISH - 11
Page 12
Read this rst!
CAUTION:
rPOWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks
will result.
When not using the projector for an extended period of time, disconnect the power plug from the wall outlet.
Failure to do so may result in re or electric shock.
Before replacing the projection lens, be sure to turn off the power and disconnect the power plug from the wall outlet.
fUnexpected projection of light may cause injury to eyes. fReplacing the projection lens without removing the power plug may result in electric shock.
Disconnect the power plug from the wall outlet before attaching or removing the Interface Board and performing maintenance.
Failure to do so may result in electric shock.
Do not connect the power cord to the projector while current is running. Do not remove the power connector (projector-side) while current is running.
Connecting or removing the power connector while current is running may result in res caused by sparks.
rON USE/INSTALLATION
Do not place heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
fBe especially careful not to let young children stand or sit on the projector.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in re.
fTake particular care in locations exposed to direct sunlight or near heaters.
Do not place your hands in the openings beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
Do not install the projector in a location where salt pollution or corrosive gas may occur.
Doing so may result in falling due to corrosion. Also, it may result in malfunctions.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
fStrong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used. Do not block the projection by placing an object in front of the projection lens.
Doing so can cause re, damage to an object, or malfunction of the projector.
fStrong light is emitted from the projector’s lens.
The projector must be carried or installed by four or more people.
Failure to do so may cause falling accidents.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to
occur.
12 - ENGLISH
Page 13
Read this rst!
CAUTION:
rACCESSORIES
When not using the projector for an extended period of time, remove the batteries from the remote control.
Failure to observe this will cause the batteries to leak, overheat, catch re or explode, which may result in re or
contamination of surrounding area.
rMAINTENANCE
Ask your dealer about cleaning inside the projector every 20 000 hours of usage as an estimated duration.
Continuous use while dust is accumulated inside the projector may result in re.
fFor cleaning fee, ask your dealer.
To remove the battery
Remote Control Battery
1. Press the guide and lift the cover.
(ii)
(i)
2. Remove the batteries.
ENGLISH - 13
Page 14
Read this rst!
Brazil Only Brasil Apenas
rManuseio de baterias usadas
BRASIL
Após o uso, as pilhas e/ou baterias deverão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma ta isolante adesiva, antes de depositar numa caixa
destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper
a blindagem e produzir fogo. (Fig. 1)
Fig. 1 Como isolar os terminais
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a
garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem car expostas a temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta, danicar o lacre
do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais provocado internamente. Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso haja irritação, consulte um médico.
Fita Isolante
Fita Isolante
rRemoção das baterias
1. Pressione a guia e levante a tampa.
(ii)
2. Remova as baterias.
14 - ENGLISH
(i)
Page 15
rTrademarks
f SOLID SHINE is a trademark of Panasonic Corporation. f DLP is a trademark or registered trademark of Texas Instruments. f The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
TM
f DisplayPort
States and other countries.
f PJLink
TM
regions.
f Crestron Connected, the Crestron Connected logo, Crestron Fusion, Crestron RoomView, and RoomView
are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. f HDBaseT f Art-Net f Windows, Internet Explorer, and Microsoft Edge are registered trademarks or trademarks of Microsoft
Corporation in the United States and other countries. f Mac, macOS, and Safari are trademarks of Apple Inc., registered in the United States and other countries. f IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. f Android and Google Chrome are trademarks of Google LLC. f Adobe, Acrobat, Flash Player, and Reader are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries. f Some of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by
Ricoh Company, Ltd. f All other names, company names, and product names mentioned in this manual are trademarks or registered
trademarks of their respective owners.
Please note that the
Software information regarding this product
This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0), (4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.1), and/or (5) open source software other than the software licensed under the GPL V2.0 and/or LGPL V2.1. The software categorized as (3) - (5) are distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Please refer to the detailed terms and conditions thereof shown in the “Operating Instructions – Basic Guide”. “Operating Instructions – Basic Guide” is supplied with the product.
At least three (3) years from delivery of this product, Panasonic will give to any third party who contacts us at
the contact information provided below, for a charge no more than our cost of physically performing source code distribution, a complete machine-readable copy of the corresponding source code covered under GPL V2.0, LGPL V2.1 or the other licenses with the obligation to do so, as well as the respective copyright notice thereof.
Contact Information: oss-cd-request@gg.jp.panasonic.com
is a trademark owned by the Video Electronics Standards Association (VESA®) in the United
is a registered trademark or pending trademark in Japan, the United States, and other countries and
TM
is a trademark of HDBaseT Alliance.
TM
Designed by and Copyright Artistic Licence Holdings Ltd
®
and TM symbols are not specied in this manual.
rIllustrations in this manual
f Illustrations of the projector, menu screen (OSD), and other parts may vary from the actual product. f Illustrations displayed on the computer screen may differ depending on the computer type and its operating
system. f Illustrations of the projector with the power cord attached are only examples. The shape of the supplied power
cords varies depending on the country where you purchased the product.
rReference pages
f Reference pages in this manual are indicated as (x page 00).
rTerm
f In this manual, the “Wireless/wired remote control unit” accessory is referred to as “Remote control”.
ENGLISH - 15
Page 16
Features of the Projector
High luminance & high picture quality
▶ In addition to high luminance of 50 000 lm*1
*2
and high contrast of 20 000:1 projector has realized wide color gamut covering approximately 90 % of the
DCI-P3 standard. HDR (High Dynamic
Range) is also supported, allowing higher quality image content to be reproduced as a projected image.
*1 When the power supply of AC 200 V to 240 V is used and
[OPERATING MODE] is set to [NORMAL]
*2 When [DYNAMIC CONTRAST] is set to [3]
Easy and highly exible setup
, this
Quick Steps
For details, refer to the corresponding pages.
1. Set up the projector. (x page 40)
2. Attach the projection lens (optional).
(x page 49)
3. Connect with external devices. (x page 52)
4. Connect the power cord. (x page 59)
▶ Adopted the Interface Board method that
exibly supports various customer systems
for the video signal input. In addition, by supporting Art-Net, etc., it has superior compatibility with the devices other than projectors. This projector has also realized compact all-in-one body even being a 50 000 lm class. More advanced rendition in wide range of usage is possible by supporting projection in all 360° direction, etc.
Long life and high reliability
▶ In addition to adopting the solid-state light
source with long life, the projector has enhanced the dust resistance property of the optical unit that is sensitive to dust. By
eliminating the lter, the maintenance cost
for long-term operation is reduced.
5. Switch on the projector. (x page 61)
6. Make initial settings. (x page 62) Execute the lens calibration. (x page 73)
f Take this step when you switch on the
power for the rst time after purchasing the
projector.
7. Select the input signal. (x page 69)
8. Adjust the image. (x page 71)
16 - ENGLISH
Page 17

Chapter 1 Preparation

This chapter describes things you need to know or check before using the projector.
ENGLISH - 17
Page 18
Chapter 1 Preparation — Precautions for use

Precautions for use

Intended use of the product

The purpose of the projector is to project a video signal from imaging equipment or a computer on a screen or other surface as a still image or moving image.

Installation and handling of the laser product (for USA and Canada)

rFor permanent Installation
f Installation of the projector shall be performed by a technician trained by Panasonic. f The variance application to the U.S. Food and Drug Administration (FDA variance application) will be performed
by Panasonic. The person responsible of the device or usage shall store the original or a copy of the FDA variance approval letter received from Panasonic.
rFor temporary installation
f Installation of the projector shall be performed by a technician trained by Panasonic. f Owner of the projector or the person responsible of usage such as the promotor of the show shall apply for FDA
variance and acquire the approval letter.
f The variance holder who has acquired the FDA variance approval letter must submit the “installation checklist”
required by FDA to Panasonic.
f Variance holder shall create and store a document recording the information such as the location of the use,
dates of the use, users of the projector.
rFor use
f This projector is categorized as the risk group 3 of IEC 62471-5:2015. f Do not enter within the hazard distance (within RG3 range), refer to “Hazard distance (IEC 62471-5:2015)” (x
page 9).
f Assign a person responsible of the device when using the projector. The person responsible shall be trained by
Panasonic before starting to use the projector.
Note
f Information such as training, FDA variance application, installation checklist, usage recording document can be conrmed by
accessing following URL.
https://eww.pavc.panasonic.co.jp/projector/extranet/index.html

Cautions when transporting

f Transport the projector with four or more people. Failure to do so may drop the projector, which may result in
damage or deformation of the projector, or injury.
f When transporting the projector, hold it securely by its handle on the outer perimeter of the projector and avoid
excessive vibration and impact. Failure to do so may cause a failure due to the damaged internal components.
f Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

Cautions when installing

rDo not set up the projector outdoors.
The projector is designed for indoor use only.
rDo not set up the projector in the following locations.
f Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal
components or malfunction.
f Location close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to
do so may shorten the life of the components and result in malfunctions.
f Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may uctuate in rare
cases due to the heated air from the exhaust vent or the hot or cooled air from the air conditioner. Make sure that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
18 - ENGLISH
Page 19
Chapter 1 Preparation — Precautions for use
f Places with sharp temperature uctuations such as near lights (studio lamps): Doing so may shorten the life of
the light source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector. f Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector. f Places where there is high-power laser equipment: Directing a laser beam onto the projection lens surface
causes damage to the DLP chips.
rAsk a qualied technician or your dealer to do installation work such as mounting the
projector on the ceiling, including installation work that uses eyebolts.
To ensure projector performance and security, ask a qualied technician or your dealer when installing the projector in a method other than the oor installation or when installing the projector in a high place.
rAsk a qualied technician or your dealer to install the cable wiring for DIGITAL LINK
connection.
Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate installation.
rThe projector may not work properly due to strong radio wave from the broadcast
station or the radio.
If there is any facility or equipment which outputs strong radio waves near the installation location, install the
projector at a location sufciently far from the source of the radio waves. Or, wrap the LAN cable connected to the
<DIGITAL LINK> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.
rFocus adjustment
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power.
It is recommended to perform the focus adjustment after 30 minutes have elapsed with the focus test pattern displayed. For details of the test pattern, refer to “[TEST PATTERN] menu” (x page 181) .
rDo not install the projector at an altitude of 4 200 m (13 780') or higher above sea level.
rDo not use the projector in a location where the ambient temperature exceeds 45 °C
(113 °F).
Using the projector in a location where the altitude is too high or the ambient temperature is too high may reduce the life of the components or result in malfunctions.
Upper limit of the operating environment temperature varies depending on the altitude above sea level.
When using the projector at an altitude between 0 m (0') and 1 400 m (4 593') above sea level: 0 °C (32 °F) to 45 °C (113 °F)
When using the projector at an altitude between 1 400 m (4 593') and 4 200 m (13 780') above sea level: 0 °C (32 °F) to 40 °C (104 °F)
Do not use the projector in a location where the ambient temperature exceeds 40 °C (104 °F) regardless of the altitude when the optional Wireless Module (Model No.: AJ-WM50 Series) is attached to the projector.
ENGLISH - 19
Page 20
Chapter 1 Preparation — Precautions for use
rProjection in all 360° direction is possible.
360°
360° vertically 360° horizontally 360° tilted
360°
(combination of vertical and horizontal)
360°
rThe geometric adjustment is disabled when projecting an image in simultaneous
format or image with high frame rate.
The geometric adjustment function cannot be used when the video signal in simultaneous format or the video signal with vertical scanning frequency of 100 Hz or 120 Hz is input.
When projecting an image in simultaneous format or an image with vertical scanning frequency of 100 Hz or 120 Hz, install the projector following the instructions below so that distortion does not occur in the projected image.
f Use a at screen. f Install the projector so that the front side of the projector is parallel to the screen. f Install the projector so that the image can be projected within the lens shift adjustment range.
20 - ENGLISH
Page 21
Chapter 1 Preparation — Precautions for use

Cautions when setting up the projector

f Install the projector in a place or with a mount that can sufciently tolerate the weight. The position of the
projected image may shift if the strength is not sufcient.
f Use the adjustable feet only for the oor standing installation and for adjusting the angle. Using them for other
purposes may damage the projector. f The adjustable feet can be removed if not needed in the installation. However, do not use the screw holes
where the adjustable feet were removed to x the projector to a mount.
Do not insert any screws other than the eyebolts for the installation work into the screw holes of the removed
adjustable feet. Do not insert the removed adjustable feet into other M10 screw holes. f Do not x the projector to a mount with the screw holes for eyebolts (4 locations on each side) on the top side,
right and left sides, and back side. f When installing and using the projector in a method other than the oor installation using the adjustable feet,
remove the adjustable feet (4 locations) and use the six screw holes to x the projector to a mount (as shown in
the gure).
For the screws to x the projector, use commercially available ISO 898-1 standard screws (made of carbon steel
or alloy steel).
(Screw diameter: M10, thread engagement length: 18 mm (23/32") or more, tapping depth inside the projector:
30 mm (1-3/16"))
In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector
bottom and the setting surface by inserting spacers (metallic) between them.
f Use a torque screwdriver or Allen torque wrench to tighten the xing screws to their specied tightening torques.
Do not use electric screwdrivers or impact screwdrivers.
(Screw tightening torque: 20 ± 1 N·m)
Unit: mm
Adjustable feet
Screw tightening torque: (M6) 4 ± 0.5 N·m
Adjustable feet
Positions of screw holes to fix projector and
adjustable feet
Screw holes to fix the projector
M6
30 (1-3/16")
Tapping depth (common for 6 locations)
Mount
ENGLISH - 21
Page 22
Chapter 1 Preparation — Precautions for use
f Do not stack three or more projectors. f Do not use the projector supporting it by the top. f Do not block the intake/exhaust vents of the projector. f Prevent hot and cool air from the air conditioning system to blow directly to the intake/exhaust vents of the
projector.
500 mm (19-11/16") or longer
500 mm (19-11/16") or longer
500 mm (19-11/16") or longer
100 mm (3-15/16") or longer
f Do not install the projector in a conned space.
When installing the projector in a conned space, provide air conditioning or ventilation separately. Exhaust heat
may accumulate when the ventilation is not enough, triggering the protection circuit of the projector. f Panasonic takes no responsibility for any damage to the product caused by an inappropriate choice of location
for installing the projector, even if the warranty period of the product has not expired.
22 - ENGLISH
Page 23
Chapter 1 Preparation — Precautions for use
rCautions when conducting lifting work
f Use the eyebolts only when temporarily lifting the projector such as when installing the projector. f Use ISO 3266 standard eyebolts (commercially available) for the M10 with an underhead length of 18 mm
(23/32") to 30 mm (1-3/16"). Also use ISO standard parts for other components to lift the projector (wires, etc.).
f Lift the projector using the eyebolts attached to 4 locations on the same plane. f Set the lifting angle to 60° or more.
60° or more
18 mm (23/32") - 30 mm (1-3/16")

Security

When using this product, take safety measures against the following incidents.
f Personal information being leaked via this product f Unauthorized operation of this product by a malicious third party f Interfering or stopping of this product by a malicious third party
Take sufcient security measures.
f Make your password difcult to guess as much as possible. f Change your password periodically. A password can be set in the [SECURITY] menu [SECURITY
PASSWORD CHANGE]. f Panasonic Corporation or its afliate companies will never ask for your password directly. Do not divulge your
password in case you receive such inquiries. f The connecting network must be secured by a rewall, etc. f Set a password for the web control and restrict the users who can log in. A password for the web control can be
set in the [Change password] page of the web control screen.
ENGLISH - 23
Page 24
Chapter 1 Preparation — Precautions for use
rSecurity when using the wireless LAN product
The advantage of a wireless LAN is that information can be exchanged between a computer or other such equipment and a wireless access point using radio waves, instead of using a LAN cable, as long as you are within range for radio transmissions.
On the other hand, because the radio wave can travel through an obstacle (such as a wall) and is accessible from anywhere within a given range, following problems may occur if security setting is insufcient.
f Transmitted data may be intercepted
A malicious third part may intentionally intercept radio waves and monitor the following transmitted data.
g Personal information such as your ID, password, credit card number g Content of an Email
f Illegally accessed
A malicious third party may access your personal or corporate network without authorization and engage in the
following types of behavior.
g Retrieve personal and/or secret information (information leak) g Spread false information by impersonating a particular person (spoong) g Overwrite intercepted communications and issue false data (tampering) g Spread harmful software such as a computer virus and crash your data and/or system (system crash)
Since most wireless LAN adapters or access points are equipped with security features to take care of these problems, you can reduce the possibility of these problems occurring when using this product by making the appropriate security settings for the wireless LAN device.
Some wireless LAN devices may not be set for security immediately after purchase. To decrease the possibility of occurrence of security problems, be sure to make all security related settings according to the operation instructions supplied with each wireless LAN device before using a wireless LAN device.
Depending on the specications of the wireless LAN, a malicious third party may be able to break security settings
by special means. Panasonic asks customers to thoroughly understand the risk of using this product without making security
settings, and recommends that the customers make security settings at their own discretion and responsibility.

Notes regarding the wireless LAN

Radio wave in the 2.4 GHz band is used when the wireless LAN connection function of the projector is used. The license of wireless station is not required, but understand the following when using.
To use the wireless LAN function with the projector, it is necessary to attach the optional Wireless Module (Model
No.: AJ-WM50 Series).
rDo not use close to other wireless devices.
Following devices may be using radio wave in the same bandwidth as the projector. Using the projector close to these devices may cause the communication to be disabled or the communication speed to slow down due to interference of radio wave.
f Microwave oven, etc. f Industrial, scientic, or medical devices, etc. f In-plant wireless station for identifying moving vehicles used in the manufacturing lines at a plant f Specied low power wireless station
rDo not use cell phone, television, or radio as much as possible close to the projector.
Cell phone, television, or radio is using radio wave with different bandwidth from the projector, so there is no effect on the wireless LAN communication or the send/receive on these devices. However, noise may occur in the audio or video due to the radio wave from the projector.
rRadio wave for wireless LAN communication does not go through the reinforcing
bars, metal, or concrete.
The projector can communicate through wall or oor made of wood or glass (excluding the glass with metal mesh embedded), but it cannot communicate through wall or oor made of reinforcing bars, metal, or concrete.
24 - ENGLISH
Page 25
Chapter 1 Preparation — Precautions for use
rDo not use the projector as much as possible in a location where static electricity is
generated.
The communication via wireless LAN or wired LAN may be prone to disruption when the projector is used in a location where static electricity or noise is generated.
There is a rare case that the LAN connection may not be established due to static electricity or noise, so in such case, turn off the projector, remove the source of problematic static electricity or noise, and turn the projector back on.

DIGITAL LINK

“DIGITAL LINK” is a technology to transmit the video, audio, Ethernet, and serial control signals using a twisted
pair cable by adding unique functions by Panasonic to the HDBaseTTM communication standard formulated by HDBaseT Alliance.
This projector supports the optional Panasonic DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) and peripheral devices by other manufacturers (twisted-pair-cable transmitters such as the “XTP transmitter” of Extron Electronics) that use the same HDBaseT manufacturers that the operation has been veried with this projector, visit the Panasonic website (https:// panasonic.net/cns/projector/). Note that the verication for devices of other manufacturers has been made for the items set by Panasonic Corporation, and not all the operations have been veried. For operation or performance
problems caused by the devices of other manufacturers, contact the respective manufacturers. This projector does not support audio transmission because it is not equipped with audio function.
TM
standard. For the devices of other

Art-Net

“Art-Net” is an Ethernet communication protocol based on the TCP/IP protocol.
By using the DMX controller and the application software, illumination and stage system can be controlled. Art-Net is made based on DMX512 communication protocol.

Application software supported by the projector

The projector supports following application software. For details or downloading application software other than
the “Geometric & Setup Management Software”, visit the Panasonic website (https://panasonic.net/cns/projector/).
f Logo Transfer Software
This application software transfers the original image, such as company logo, which is projected at the start, to
the projector.
f Smart Projector Control
This application software sets and adjusts the projector connected via LAN using a smartphone or a tablet.
f Multi Monitoring & Control Software
This application software monitors and controls the multiple display devices (projector and at panel display)
connected to an intranet.
f Early Warning Software
This plug-in software monitors the status of the display devices and their peripherals within an intranet, and
noties of abnormality of such equipment and detects the signs of possible abnormality. “Early Warning
Software” is pre-installed in the “Multi Monitoring & Control Software”. To use the early warning function of
this plug-in software, install “Multi Monitoring & Control Software” in the PC to be used. By enabling the early
warning function, it will notify of the approximate time to replace the consumables for the display devices,
to clean each part of the display devices, and to replace the components of the display devices, allowing to
execute maintenance in advance.
The early warning function can be used by registering maximum of 2048 display devices free of charge for
90 days after installing the “Multi Monitoring & Control Software” into a PC. To continuously use after the 90
days, it is necessary to purchase the license of “Early Warning Software” (ET-SWA100 Series) and perform
the activation. Also, depending on the type of license, the number of display devices that can be registered for
monitoring varies. For details, refer to the Operating Instructions of “Multi Monitoring & Control Software”.
f Geometric & Setup Management Software (Geometry Manager Pro)
This application software performs detailed corrections and adjustments such as the geometric adjustment
which cannot be covered by the projector settings in real-time. Also, the geometric adjustment and edge
blending matching the shape of the screen using a camera, and the adjustment of color and luminance can be
automatically performed with simple steps.
“Geometric & Setup Management Software” can be downloaded from the Panasonic website (https://panasonic.
net/cns/projector/pass/). It is necessary to register and login to PASS
*1
to download.
ENGLISH - 25
Page 26
Chapter 1 Preparation — Precautions for use
*1 PASS: Panasonic Professional Display and Projector Technical Support Website
For details, visit the Panasonic website (https://panasonic.net/cns/projector/pass/).

Storing

To store the projector, store in a dry room.

Disposal

To dispose of the product, ask your local authorities or dealer for correct methods of disposal. Also, dispose of the product without disassembling.

Cautions on use

rTo get a good picture quality
In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.
rDo not touch the surface of the projection lens with your bare hands.
If the surface of the projection lens becomes dirty from ngerprints or anything else, this will be magnied and
projected onto the screen. Attach the supplied lens cover to the optional projection lens when not using the projector.
rDLP chips
f The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always
lit. Such a phenomenon does not indicate malfunction. f Directing a high-power laser beam onto the projection lens surface can damage the DLP chips. By closing the
mechanical shutter built into the projector, it can prevent damaging of the DLP chips by a high-power laser
beam while using the shutter function (shutter: closed). To close the mechanical shutter while using the shutter
function, set [MECHANICAL SHUTTER] to [ENABLE]. For details of the setting, refer to the [DISPLAY OPTION]
menu [SHUTTER SETTING].
rDo not move the projector or subject it to vibration or impact while it is operating.
Doing so may shorten the life of the built-in motor.
rLight source
The light source of the projector uses laser diode, and has the following characteristics.
f Depending on the operating environment temperature, the luminance of the light source will decrease.
The higher the temperature becomes, the more the luminance of the light source decreases. f The luminance of the light source will decrease by duration of usage.
If brightness is noticeably reduced and the light source does not turn on, ask your dealer to clean inside the
projector or replace the light source unit.
rComputer and external device connections
When connecting a computer or an external device, read this manual carefully regarding the use of power cords and shielded cables as well.
rSlots
This projector is equipped with two SLOT NX-specication slots.
The input for HDMI, DVI-D, and SDI can be added by installing the optional Interface Board in the slot.
The supplied Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is already installed in one of the slots. “SLOT NX” is a name of the slot unique to Panasonic supporting the signal input for the 4K image.
26 - ENGLISH
Page 27
Chapter 1 Preparation — Precautions for use

Accessories

Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories.
Wireless/wired remote control unit <1>
(N2QAYB001176)
Power cord
(K2CZ3YY00085): for 200 V - 240 V
(K2CZ3YY00084): for 200 V - 240 V
(K2CG3YY00220): for 100 V - 120 V
Lens hole cover <1>
(DPHR1165ZA/X1)
(Attached to the product at the time of purchase)
Interface Board for 12G-SDI <1>
(ET-MDN12G10)
(Attached to the product at the time of purchase)
AA/R6 or AA/LR6 battery <2>
(For remote control unit)
Attention
f After unpacking the projector, discard the power cord cap and packaging material properly. f Do not use the supplied power cord for devices other than this projector. f For missing accessories, consult your dealer. f Store small parts in an appropriate manner, and keep them away from small children.
Note
f The supplied Interface Board for 12G-SDI (ET-MDN12G10) is already installed in <SLOT 1> at the time of purchase. f The type and number of the supplied power cords vary depending on the country or region where you purchased the
product.
f The model numbers of accessories are subject to change without prior notice.
ENGLISH - 27
Page 28
Chapter 1 Preparation — Precautions for use

Optional accessories

Optional accessories (product name) Model No.
Projection lens Zoom Lens
Interface Board for HDMI 2 input
Interface Board for DVI-D
Interface Board
2 input Interface Board for 12G-SDI ET-MDN12G10 Interface Board for
DisplayPort 2 input
Wireless Module
*1
Early Warning Software
(Basic license/3-year license)
NFC Upgrade Kit
*1
Digital Interface Box ET-YFB100G DIGITAL LINK Switcher ET-YFB200G
*1 The availability of this product varies depending on the country. For details, contact your dealer. *2 The sufx of the Model No. differs depending on the country.
Example of the Model No. with sufx for AJ-WM50 Series
AJ-WM50E, AJ-WM50G1, AJ-WM50G2, AJ-WM50GAN, AJ-WM50GPX, AJ-WM50P
*3 The sufx of the Model No. differs according to the license type.
ET-D3QW300, ET-D3QS400, ET-D3QT500, ET-D3QT600, ET-D3QT700, ET-D3QT800
ET-MDNHM10
ET-MDNDV10
ET-MDNDP10
AJ-WM50 Series
ET-SWA100 Series
*2
*3
ET-NUK10
Note
f Use the Wireless Module (Model No.: AJ-WM50 Series) in an environment of 0 °C (32 °F) to 40 °C (104 °F), including when
it is attached to the projector.
f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface
Board for HDMI 2 input (Model No.: ET-MDNHM10), it is necessary for the rmware version of the Interface Board for HDMI
2 input to be 2.00 or later. If the version is earlier than 2.00, the simultaneous process is not performed even if corresponding
signal is input. Consult your dealer regarding the version update to the latest rmware.
For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board”
(x page 36).
f The optional NFC Upgrade Kit (Model No.: ET-NUK10) can be used to enable the NFC function of the projector. Note that
there are some models that have the NFC function enabled from the time of factory shipment, and there are some countries
or regions where the NFC Upgrade Kit cannot be applied.
For the availability of the NFC function in the country or region where you purchased the product, visit the Panasonic website
(https://panasonic.net/cns/projector/) or consult your dealer.
f The model numbers of optional accessories are subject to change without prior notice. f The optional accessories compatible with the projector may be added or changed without prior notice. The optional
accessories described in this document are as of November 2019.
For the latest information, visit the Panasonic website (https://panasonic.net/cns/projector/).
28 - ENGLISH
Page 29
Chapter 1 Preparation — About your projector

About your projector

Remote control

Front Top
1 2
3
4
11
12
13
21
5
6 7
8
9
10
1 Remote control indicator
Blinks if any button in the remote control is pressed.
2 Power on <b> button
Sets the projector to projection mode when the <MAIN POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
4 <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen. (x page 84)
5 <ON SCREEN> button
Switches the on-screen display function on (display) or off (hide). (x page 79)
6 <AUTO SETUP> button
Automatically adjusts the image display position and signal level while projecting the image. [PROGRESS] is displayed while in automatic adjustment. (x page 80)
7 <ASPECT> button
Switches the aspect ratio of the image. (x page 80)
8 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple projector environment.
9 <STATUS> button
Displays the projector information.
10 <LIGHT> button
Pressing this button lights up the remote control buttons. The lights will go off when the remote control operation goes idle for 10 seconds.
11 <INPUT MENU> button
Displays the input selection screen. (x page 71)
14 15 16
17 18
19
20
Bottom
A strap can be attached depending on the usage.
22
23
12 Input selection buttons (<SDI>, <DIGITAL LINK>, <HDMI>,
<DVI-D>, <DISPLAYPORT>, <SLOT 1>, <SLOT 2>)
Switches the input signal to project. (x page 69) <HDMI> button, <DVI-D> button, <DISPLAYPORT> button, <SLOT 1> button, and <SLOT 2> button can be used when the optional Interface Board equipped with corresponding input is installed in the slot on the projector. Following buttons are not used with this projector. <RGB1> button, <RGB2> button, <VIDEO> button, <S-VIDEO Y/C> button
13 <SHUTTER> button
Used to temporarily turn off the image. (x page 79)
14 <TEST PATTERN> button
Displays the test pattern. (x page 81)
15 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the focus, zoom, and lens shift. (x page 71)
16 <FUNCTION> button
Assigns a frequently used operation as a shortcut button. (x page 80) When the <FUNCTION> button is held down, the [FUNCTION
BUTTON] screen is displayed. (x page 172)
17 <DEFAULT> button
Resets the setting of the displayed sub-menu to the factory default. (x page 85)
18 <ID SET> button
Sets the ID number of the remote control in a multiple projector environment. (x page 37)
19 <ID ALL> button
Used to simultaneously control all the projectors with a single remote control in a multiple projector environment. (x page 37)
20 <LOCK> button
Used to prevent unintended operation by careless pressing of the buttons and prevent draining the remote control batteries. Operation of each button on the remote control is disabled by sliding the <LOCK> button toward the arrow.
21 Remote control signal transmitter
ENGLISH - 29
Page 30
Chapter 1 Preparation — About your projector
22 Remote control wired terminal
23 Strap hole
This is a terminal used to connect to the projector via a cable when the remote control is used as a wired remote control. (x page 38)
Attention
f Do not drop the remote control. f Avoid contact with liquids or moisture. f Do not attempt to modify or disassemble the remote control. f Do not swing the remote control holding onto the strap when a strap is attached. f Observe the following instructions that are indicated on the caution label at the back of the remote control:
g Do not use old battery with new one. g Do not use batteries other than the type specied. g Be sure the batteries are inserted properly.
For other instructions, read the instructions related to batteries that are described in “Read this rst!”.
1.Do not use old battery with new one.
2.Do not use batteries other than the type specified.
3.Be sure the batteries are inserted properly.
N2QAYB001176
Made in China
Caution label at the back of the remote control
Note
f When operating the remote control by directly pointing the remote control signal receiver of the projector, operate the remote control at
a distance approx. 30 m (98'5") or shorter from the remote control signal receiver. The remote control can control at angles of up to ±15°
vertically and ±30° horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly. f The signal will be reected off the screen. However, the operating range may be limited from light reection loss due to the screen material. f If the remote control signal receiver directly receives strong light, such as uorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
30 - ENGLISH
Page 31

Projector body

Chapter 1 Preparation — About your projector
Front
1 2 345
6 67
Rear
Side
78 8
77 88
9 88
8 8
7 12
1311
108 8
Projection direction
1 Remote control signal receiver (front) 2 Power indicator <ON (G)/STANDBY (R)>
Indicates the status of the power.
3 Light source indicator <LIGHT1>
Indicates the status of light source 1.
4 Light source indicator <LIGHT2>
Indicates the status of light source 2.
5 Temperature indicator <TEMP>
Indicates the internal temperature status.
6 Adjustable feet
Adjusts the projection angle.
7 Intake vent 8 Screw holes for eyebolts
Screw diameter: M10, tapping depth inside the projector:
35 mm (1-3/8")
88
14
15
9 Remote control signal receiver (rear) 10 Exhaust vent 11 Control panel (x page 33) 12 Connecting terminals (x page 34) 13 NFC touch point
This is the touch point when using the near eld communication (NFC, Near Field Communication) function. A device such as a
smartphone equipped with the NFC function can be connected to the projector by holding it near the touch point.
14 <MAIN POWER> switch
Turns on/off the main power.
15 <AC IN> terminal
Connect the supplied power cord.
ENGLISH - 31
Page 32
Chapter 1 Preparation — About your projector
BottomTop
3
1
2
Projection direction
WARNING
Do not touch the top surface of the projector during use.
f Doing so may result in burns, as the top surface is hot during
use and for a while after use.
Attention
4
1 Screw holes for eyebolts
Screw diameter: M10, tapping depth inside the projector:
35 mm (1-3/8")
2 Remote control signal receiver (top)
3 Handle
Hold the handle with your hand when carrying the projector.
4 Screw holes to x the projector
Screw diameter: M10, tapping depth inside the projector:
30 mm (1-3/16")
f Do not block the intake/exhaust vents of the projector.
Note
f The optional NFC Upgrade Kit (Model No.: ET-NUK10) can be used to enable the NFC function of the projector. Note that there are some
models that have the NFC function enabled from the time of factory shipment, and there are some countries or regions where the NFC Upgrade Kit cannot be applied.
For the availability of the NFC function in the country or region where you purchased the product, visit the Panasonic website (https://
panasonic.net/cns/projector/) or consult your dealer.
f For the connection using the NFC function, use the application software “Smart Projector Control” which performs the setting and
adjustment of the projector.
For details on the “Smart Projector Control”, visit the Panasonic website (https://panasonic.net/cns/projector/).
32 - ENGLISH
Page 33
r Control panel
Chapter 1 Preparation — About your projector
8
1 2
3
4
5 6
7
9 10 11
12 13
14
1 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <b> button
Sets the projector to projection mode when the <MAIN POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 <MENU> button
Displays or hides the main menu. (x page 84) Returns to the previous menu when a sub-menu is displayed.
4 <ON SCREEN> button
Switches the on-screen display function on (display) or off (hide). (x page 79)
5 Input selection buttons (<SLOT 1>, <SLOT 2>, <DIGITAL
LINK>)
Switches the input signal to project. (x page 69) <SLOT 1> button and <SLOT 2> button can be used when the optional Interface Board is installed in the slot on the projector.
6 Input selection terminal indicator
Indicator that shows the selected input terminal. This indicator lights up when a video signal is being input to the selected terminal, and blinks when there is no video signal being input.
7 <INPUT MENU> button
Displays the input selection screen. (x page 71)
8 Information monitor
Displays various statuses and error information. (x page 229)
9 <INFO> button
Used to operate the information monitor. (x page 229)
10 asqw buttons
Used to select items in the menu screen, change settings, and adjust levels. Also used to enter a password in [SECURITY] or enter characters.
11 <LENS> button
Adjusts the focus, zoom, and lens shift.
12 <ENTER> button
Determines and executes an item in the menu screen.
13 <SHUTTER> button
Used to temporarily turn off the image. (x page 79)
14 <LIGHT> switch
This is a light switch for the connecting terminals and control panel.
ENGLISH - 33
Page 34
r Connecting terminals
6 7
8
Chapter 1 Preparation — About your projector
1 52 3 4
9 10 11 12
1 <REMOTE 1 IN> terminal/<REMOTE 1 OUT> terminal
These are terminals to connect the remote control for serial control in a multiple projector environment.
2 <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the external control circuit.
3 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control the projector by connecting a computer.
4 <SERIAL OUT> terminal
This is a terminal to output the signal connected to the <SERIAL IN> terminal.
5 <MULTI PROJECTOR SYNC IN> terminal/<MULTI
PROJECTOR SYNC OUT> terminal
This terminal is used to connect multiple projectors when balancing the contrast as a combined screen or synchronizing the effects using the shutter function including the fade in/fade out with a system using multiple projectors.
6 Slots (<SLOT 1>, <SLOT 2>)
There are SLOT NX-specication slots to install the optional
Interface Board internally.
7 Interface Board for 12G-SDI
The supplied Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is already installed. (x page 36)
8 Slot cover
9 <LAN> terminal
This is the LAN terminal to connect to the network.
10 <DIGITAL LINK> terminal
This is a terminal to connect a device that transmits video signal via the LAN terminal. Also, this is the LAN terminal to connect to the network.
11 <DC OUT 1> terminal/<DC OUT 2> terminal
This is the USB terminal dedicated for power supply. (DC 5 V,
total 2 A) Use this terminal when a power supply is required to wireless display adapters and wireless LAN/Ethernet converters, etc.
12 <USB> terminal
This is a terminal to connect the USB memory when using the data cloning function or rmware update function. (x pages 239, 243) This is also the terminal to connect the optional Wireless
Module (Model No.: AJ-WM50 Series) when the projector is connected via wireless LAN. (x page 200)
Note
f When a LAN cable is directly connected to the projector, the network connection must be made indoors. f To transmit the Ethernet and serial control signals using the <DIGITAL LINK> terminal, set the [NETWORK] menu [NETWORK
CONTROL] [TYPE SELECT] to [DIGITAL LINK] or [LAN & DIGITAL LINK].
f To transmit the Ethernet signal using the <LAN> terminal, set the [NETWORK] menu [NETWORK CONTROL] [TYPE SELECT] to
[LAN] or [LAN & DIGITAL LINK].
f The <DIGITAL LINK> terminal and the <LAN> terminal are connected inside of the projector when the [NETWORK] menu [NETWORK
CONTROL] [TYPE SELECT] is set to [LAN & DIGITAL LINK]. Do not directly connect the <DIGITAL LINK> terminal and the <LAN> terminal using a LAN cable. Construct the system so that it is not connected to the same network via the peripherals such as the hub or the twisted-pair-cable transmitter.
f Power can be supplied using the <DC OUT 1> terminal and the <DC OUT 2> terminal even when the projector is in the standby status.
34 - ENGLISH
Page 35
Chapter 1 Preparation — About your projector

Names and functions of the Interface Board

This projector is equipped with two SLOT NX-specication slots.
The input for HDMI, DVI-D, and SDI can be added by installing the optional Interface Board in the slot.
The supplied Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is already installed in one of the slots.
The terminal name of the optional Interface Board is described with different terminal name in this document when it is installed in <SLOT 1> and when it is installed in <SLOT 2>. Refer to following information for details.
r Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
This board supports the HDMI signal.
13 32
1 <HDMI IN 1> terminal (when installed in <SLOT 1>), <HDMI
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input HDMI signal.
2 <HDMI IN 2> terminal (when installed in <SLOT 1>), <HDMI
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input HDMI signal.
3 Handle
Note
f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI
2 input (Model No.: ET-MDNHM10), it is necessary for the rmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the
version is earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding
the version update to the latest rmware. For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board” (x page 36).
r Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
This board supports the DVI-D signal.
13 32
1 <DVI-D IN 1> terminal (when installed in <SLOT 1>), <DVI-D
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input DVI-D signal.
2 <DVI-D IN 2> terminal (when installed in <SLOT 1>), <DVI-D
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input DVI-D signal.
3 Handle
r Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10)
This board supports the DisplayPort signal.
13 32
1 <DisplayPort IN 1> terminal (when installed in <SLOT 1>),
<DisplayPort IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input DisplayPort signal.
2 <DisplayPort IN 2> terminal (when installed in <SLOT 1>),
<DisplayPort IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input DisplayPort signal.
3 Handle
ENGLISH - 35
Page 36
Chapter 1 Preparation — About your projector
r Interface Board for 12G-SDI (Model No.: ET-MDN12G10)
This board supports the HD-SDI signal, the 3G-SDI signal, the 6G-SDI signal, and the 12G-SDI signal. The operation will be the same when this board is installed in <SLOT 1> or <SLOT 2>.
25 541 3
1 <SDI 1 IN> terminal
This is a terminal to input SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI).
2 <SDI 2 IN/1 OUT> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 1 IN>
terminal of this board.
3 <SDI 3 IN> terminal
This is a terminal to input SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI).
4 <SDI 4 IN/3 OUT> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 3 IN>
terminal of this board.
5 Handle
Note
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal. f To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu [SLOT
IN] [SDI MODE] to [OUTPUT].
f When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
How to conrm the rmware version of the Interface Board
r Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
The Interface Board for HDMI 2 input with the rmware version 2.00 or later has the version displayed on the
product. The rmware version can also be conrmed in the [STATUS] screen. (x page 173)
Display example
36 - ENGLISH
Ver. 2.00
Firmware version 2.00
Page 37
Chapter 1 Preparation — Preparing the remote control

Preparing the remote control

Inserting and removing the batteries

(ii)
(i)
Fig. 1 Fig. 2
1) Open the cover. (Fig. 1)
2) Insert the batteries and close the cover (insert the m side first). (Fig. 2)
f When removing the batteries, perform the steps in reverse order.

When using the multiple projectors

When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector individually using single remote control, if a unique ID number is assigned to each projector.
When using the projectors by setting the ID numbers, set the ID number of the projector body after initial settings have been completed. Then, set the ID number of the remote control. For initial settings, refer to “When the initial
setting screen is displayed” (x page 62). The factory default ID number of the projector (projector body and remote control) is set to [ALL], so you can use
it as it is. Set the ID numbers of the projector body and remote control as necessary.
For details on setting the ID number of the remote control, refer to “Setting ID number of the remote control” (x page 81).
Note
f Set the ID number of the projector body from the [PROJECTOR SETUP] menu [PROJECTOR ID].
ENGLISH - 37
Page 38
Chapter 1 Preparation — Preparing the remote control

Connecting the remote control to the projector with a cable

If you control the multiple projectors with a single remote control, use commercially available M3 stereo mini jack cables to connect to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projectors.
The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.
M3 stereo mini jack cable (commercially available)
Remote control
Connecting to a second projector
Connecting to the remote control wired terminal
Connecting terminals
Attention
f Use a cable that is 15 m (49'3") or shorter, with 2 core shielded. The remote control may not operate when the length of the cable exceeds
15 m (49'3") or when the shielding of the cable is inadequate.
38 - ENGLISH
Page 39

Chapter 2 Getting Started

This chapter describes things you need to do before using the projector such as the setup and connections.
ENGLISH - 39
Page 40
Chapter 2 Getting Started — Setting up

Setting up

Usable outlet

This projector supports AC 100 V to AC 120 V, and AC 200 V to AC 240 V as the power supply. A grounded outlet supporting 30 A is required when using the projector with AC 200 V to AC 240 V. A grounded outlet supporting 15 A is required when using the projector with AC 100 V to AC 120 V.
The shape of the usable outlet differs depending on the power supply. Following illustrations are examples.
2P/3W 30 A 250 V
NEMA L6-30
2P/3W 32 A 250 V
Clock position 6h
2P/3W 15 A 125 V
Attention
f Use the supplied power cord and ground at the outlet. f Use the power cord matching the used power supply voltage and outlet shape.
Note
f The light output will decrease to approximately 1/5 when using the projector with AC 100 V to AC 120 V. f The supplied power cords vary depending on the country or region where you purchased the product.

Installation mode

The installation modes of the projector are as follows. Set [FRONT/REAR]/[FLOOR/CEILING] in the [PROJECTOR SETUP] menu [PROJECTION METHOD] (x page 143) depending on the installation mode.
Setting on a desk/oor and projecting forward Setting on a desk/oor and projecting from rear
(Using the translucent screen)
Menu item Setting value Menu item Setting value
[FRONT/REAR] [FRONT] [FRONT/REAR] [REAR]
[FLOOR/CEILING] [AUTO] or [FLOOR] [FLOOR/CEILING] [AUTO] or [FLOOR]
Mounting on the ceiling and projecting forward Mounting on the ceiling and projecting from rear
(Using the translucent screen)
Menu item Setting value Menu item Setting value
[FRONT/REAR] [FRONT] [FRONT/REAR] [REAR]
[FLOOR/CEILING] [AUTO] or [CEILING] [FLOOR/CEILING] [AUTO] or [CEILING]
40 - ENGLISH
Page 41
Chapter 2 Getting Started — Setting up
Portrait setting and projecting forward Portrait setting and projecting from the rear
(Using the translucent screen)
Menu item Setting value Menu item Setting value
[FRONT/REAR] [FRONT] [FRONT/REAR] [REAR]
[FLOOR/CEILING]
Set in accordance with the image to project.
[FLOOR/CEILING]
Set in accordance with the image to project.
Note
f In the portrait setting, the on-screen menu is displayed sideways.
To display the on-screen menu vertically, change the [OSD ROTATION] setting in the [DISPLAY OPTION] menu [ON-SCREEN DISPLAY] (x page 133).
f The projector has a built-in angle sensor. The attitude of the projector is automatically detected by setting [FLOOR/CEILING] to [AUTO] in
the [PROJECTOR SETUP] menu [PROJECTION METHOD].
r Angle sensor
The range of the installation attitude that is detected by the angle sensor built-in the projector is as follows.
Floor standing installation
Floor standing installation
Projection direction
30°
30°
Ceiling mount installation
ENGLISH - 41
Page 42
Chapter 2 Getting Started — Setting up

Interface Board

This projector is equipped with two SLOT NX-specication slots.
The input for HDMI, DVI-D, and SDI can be added by installing the optional Interface Board in the slot.
The supplied Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is already installed in one of the slots.
Attention
f Requesting a qualied technician to install or remove the Interface Board is recommended. A malfunction may occur due to static electricity.
Consult your dealer.

Projected image and throw distance

Install the projector referring to the projected image size, projection distance, etc.
Attention
f Before setting up, read “Precautions for use” (x page 18). f The geometric adjustment function cannot be used when the video signal in simultaneous format or the video signal with vertical scanning
frequency of 100 Hz or 120 Hz is input. When projecting an image in simultaneous format or an image with vertical scanning frequency of 100 Hz or 120 Hz, install the projector following the instructions below so that distortion does not occur in the projected image.
g Use a at screen. g Install the projector so that the front side of the projector is parallel to the screen. g Install the projector so that the image can be projected within the lens shift adjustment range.
f Do not use the projector and the high-powered laser equipment in the same room. The DLP chips can be damaged if a laser beam hits the
projection lens surface.
Figure of projected image and throw distance
Projected image
SH
SD
SW
Screen
L (LW/LT)
L (LW/LT)
SW SH
Screen
Note
f This illustration is prepared on the assumption that the projected image size and position have been aligned to t full in the screen.
SH Projected image height
SW Projected image width
SD Projected image size
*1
(LW/LT)
L
L1
*2
Projection distance (distance from the front end of the projection lens to the screen) Lens protrusion dimension (distance from the front surface of the projector to the front end of the projection
lens)
L1
L1
*1 For details about calculating the projection distance, refer to “Formula for calculating the projection distance per projection lens” (x page 47). *2 LW: Minimum projection distance when the Zoom Lens is used
LT: Maximum projection distance when the Zoom Lens is used
(Unit: m)
Projection lens Model No. Lens protrusion dimension (L1) (approximate value)
ET-D3QW300 0.246 ET-D3QS400 0.232
ET-D3QT500 0.208 ET-D3QT600 0.149 ET-D3QT700 0.221 ET-D3QT800 0.267
42 - ENGLISH
Page 43
Chapter 2 Getting Started — Setting up
Note
f For the adjustment range of the projected image position with the lens shift, refer to “Lens shift range” (x page 74).
[GEOMETRY] projection range
[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)
Screen
Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)
Projection distance Arc radius
Screen
Screen
Projection distance Arc radius
Screen
Arc center
Screen
Projection distance Arc radius
Arc center
Screen
Projection distance Arc radius
ENGLISH - 43
Page 44
Chapter 2 Getting Started — Setting up
Only [KEYSTONE] used
Projection
lens Model
No.
ET-D3QW300 ±28 ±15 ±10 ±10 1.2 3.0 0.7 1.7
ET-D3QS400 ±40 ±40 ±20 ±15 0.9 2.0 0.5 1.1 ET-D3QT500 ±40 ±40 ±20 ±15 0.9 2.0 0.5 1.1 ET-D3QT600 ±40 ±40 ±20 ±15 0.9 2.0 0.5 1.1 ET-D3QT700 ±40 ±40 ±20 ±15 0.9 2.0 0.5 1.1 ET-D3QT800 ±40 ±40 ±20 ±15 0.9 2.0 0.5 1.1
*1 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be made exceeding total of 55°.
Vertical
keystone
correction
angle α (°)
Horizontal
keystone
correction
angle β (°)
*1
[KEYSTONE] and [CURVED CORRECTION] used
together
Vertical
keystone
correction
angle α (°)
Horizontal
keystone
correction
angle β (°)
*1
Min. value of
R2/L2
Min. value of
R3/L3
Only [CURVED
CORRECTION] used
Min. value of
R2/L2
Min. value of
R3/L3
Note
f When [GEOMETRY] is used, the focus of the entire screen may be lost as correction increases. f Make the curved screen a circular arc shape with one part of a perfect circle removed. f Adjustment range of the [GEOMETRY] items may not match the listed projection range depending on the projection lens. Use this projector
within the projection range, otherwise the correction may not work.
f The geometric adjustment function cannot be used when the video signal in simultaneous format or the video signal with vertical scanning
frequency of 100 Hz or 120 Hz is input. When projecting an image in simultaneous format or an image with vertical scanning frequency of 100 Hz or 120 Hz, install the projector following the instructions below so that distortion does not occur in the projected image.
g Use a at screen. g Install the projector so that the front side of the projector is parallel to the screen. g Install the projector so that the image can be projected within the lens shift adjustment range.
44 - ENGLISH
Page 45
Chapter 2 Getting Started — Setting up
Projection distance of each projection lens
A ±5 % error in listed projection distances may occur. When [GEOMETRY] is used, distance is corrected to become smaller than the specied image size.
r When the image aspect ratio is 17:9
(Unit: m)
Projection lens Model No. ET-D3QW300 ET-D3QS400 ET-D3QT500 ET-D3QT600 ET-D3QT700 ET-D3QT800
Diagonal (SD)
2.54 (100") 1.188 2.245 2.42 3.77 3.13 4.64 4.64 7.80 5.92 8.57 8.57 12.09 10.97 17.22
3.05 (120") 1.426 2.694 2.93 4.55 3.79 5.59 5.51 9.31 7.15 10.34 10.34 14.59 13.23 20.75
3.81 (150") 1.783 3.367 3.69 5.71 4.77 7.02 6.81 11.57 8.99 12.99 12.99 18.33 16.62 26.05
5.08 (200") 2.377 4.490 4.95 7.65 6.40 9.40 8.97 15.33 12.06 17.42 17.42 24.57 22.27 34.88
6.35 (250") 2.971 5.612 6.22 9.60 8.03 11.78 11.14 19.09 15.14 21.85 21.85 30.81 27.92 43.71
7.62 (300") 3.565 6.734 7.49 11.54 9.66 14.17 13.31 22.85 18.21 26.28 26.28 37.04 33.57 52.54
8.89 (350") 4.160 7.857 8.76 13.48 11.29 16.55 15.47 26.62 21.28 30.71 30.71 43.28 39.23 61.37
10.16 (400") 4.754 8.979 10.03 15.42 12.92 18.93 17.64 30.38 24.35 35.14 35.14 49.52 44.88 70.20
12.70 (500") 5.942 11.224 12.56 19.31 16.18 23.69 21.97 37.90 30.49 44.00 43.99 62.00 56.18 87.85
15.24 (600") 7.131 13.469 15.10 23.19 19.44 28.45 26.31 45.43 36.64 52.85 52.85 74.47 67.48 105.51
17.78 (700") 8.319 15.714 17.63 27.07 22.70 33.21 30.64 52.95 42.78 61.71 61.71 86.95 78.78 123.17
20.32 (800") 9.507 17.959 20.17 30.96 25.97 37.98 34.97 60.48 48.92 70.57 70.57 99.43 90.09 140.83
22.86 (900") 10.696 20.203 22.70 34.84 29.23 42.74 39.31 68.00 55.07 79.42 79.42 111.90 101.39 158.49
25.40 (1000") 11.884 22.448 25.24 38.73 32.49 47.50 43.64 75.53 61.21 88.28 88.28 124.38 112.69 176.15
27.94 (1100") 13.073 24.693 27.77 42.61 35.75 52.26 47.97 83.05 67.36 97.14 97.14 136.86 123.99 193.81
30.48 (1200") 14.261 26.938 30.31 46.49 39.01 57.02 52.31 90.58 73.50 106.00 106.00 149.33 135.30 211.47
33.02 (1300") 15.450 29.183 32.84 50.38 42.27 61.79 56.64 98.10 79.64 114.85 114.85 161.81 146.60 229.13
35.56 (1400") 16.638 31.427 35.38 54.26 45.53 66.55 60.97 105.63 85.79 123.71 123.71 174.29 157.90 246.79
38.10 (1500") 17.827 33.672 37.91 58.15 48.80 71.31 65.31 113.16 91.93 132.57 132.57 186.76 169.20 264.44
*1 The throw ratio is based on the value during projection with the projected image size of 5.08 m (200").
Lens type Zoom Lens
Throw ratio
Projected image size Projection distance (L)
*1
Height
(SH)
Width (SW)
1.11-1.70:1 1.43-2.09:1 2.00-3.41:1 2.69-3.88:1 3.89-5.47:1 4.97-7.76:1
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
Min. (LW)
Max.
(LT)
Min. (LW)
r When the image aspect ratio is 16:10
(Unit: m)
Max.
(LT)
Projection lens Model No. ET-D3QW300 ET-D3QS400 ET-D3QT500 ET-D3QT600 ET-D3QT700 ET-D3QT800
Diagonal (SD)
2.54 (100") 1.346 2.154 2.76 4.30 3.58 5.29 5.23 8.83 6.76 9.77 9.77 13.79 12.51 19.62
3.05 (120") 1.615 2.585 3.34 5.18 4.32 6.37 6.22 10.54 8.15 11.79 11.78 16.63 15.08 23.64
3.81 (150") 2.019 3.231 4.21 6.51 5.43 8.00 7.69 13.10 10.25 14.80 14.80 20.88 18.93 29.66
5.08 (200") 2.692 4.308 5.65 8.71 7.28 10.70 10.15 17.38 13.74 19.84 19.84 27.97 25.35 39.69
6.35 (250") 3.365 5.385 7.09 10.92 9.14 13.41 12.62 21.65 17.23 24.87 24.87 35.05 31.77 49.72
7.62 (300") 4.039 6.462 8.53 13.12 10.99 16.11 15.08 25.93 20.72 29.90 29.90 42.14 38.19 59.75
8.89 (350") 4.712 7.539 9.97 15.33 12.84 18.82 17.54 30.20 24.21 34.93 34.93 49.23 44.61 69.79
10.16 (400") 5.385 8.616 11.41 17.54 14.70 21.52 20.00 34.48 27.70 39.96 39.96 56.32 51.03 79.82
12.70 (500") 6.731 10.770 14.29 21.95 18.40 26.93 24.93 43.03 34.68 50.03 50.03 70.50 63.88 99.88
15.24 (600") 8.077 12.923 17.17 26.36 22.11 32.34 29.85 51.58 41.66 60.09 60.09 84.67 76.72 119.95
17.78 (700") 9.423 15.077 20.05 30.78 25.81 37.75 34.77 60.13 48.64 70.16 70.15 98.85 89.56 140.01
20.32 (800") 10.770 17.231 22.93 35.19 29.52 43.16 39.70 68.68 55.62 80.22 80.22 113.02 102.40 160.08
22.86 (900") 12.116 19.385 25.81 39.60 33.23 48.58 44.62 77.23 62.60 90.28 90.28 127.20 115.24 180.14
25.40 (1000") 13.462 21.539 28.69 44.02 36.93 53.99 49.54 85.78 69.58 100.35 100.35 141.38 128.09 200.20
27.94 (1100") 14.808 23.693 31.57 48.43 40.64 59.40 54.47 94.33 76.56 110.41 110.41 155.55 140.93 220.27
30.48 (1200") 16.154 25.847 34.45 52.84 44.34 64.81 59.39 102.88 83.54 120.47 120.47 169.73 153.77 240.33
33.02 (1300") 17.501 28.001 37.33 57.26 48.05 70.22 64.31 111.43 90.52 130.54 130.54 183.91 166.61 260.40
35.56 (1400") 18.847 30.155 40.21 61.67 51.75 75.63 69.24 119.98 97.50 140.60 140.60 198.08 179.45 280.46
38.10 (1500") 20.193 32.309 43.09 66.08 55.46 81.04 74.16 128.53 104.48 150.67 150.67 212.26 192.30 300.53
*1 The throw ratio is based on the value during projection with the projected image size of 5.08 m (200").
Lens type Zoom Lens
Throw ratio
Projected image size Projection distance (L)
*1
Height
(SH)
Width (SW)
1.32-2.02:1 1.70-2.48:1 2.36-4.03:1 3.19-4.60:1 4.61-6.49:1 5.89-9.21:1
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
Min. (LW)
Max.
(LT)
Min. (LW)
Max.
(LT)
ENGLISH - 45
Page 46
Chapter 2 Getting Started — Setting up
r When the image aspect ratio is 16:9
(Unit: m)
Projection lens Model No. ET-D3QW300 ET-D3QS400 ET-D3QT500 ET-D3QT600 ET-D3QT700 ET-D3QT800
Diagonal (SD)
2.54 (100") 1.245 2.214 2.55 3.97 3.30 4.88 4.86 8.19 6.23 9.02 9.02 12.73 11.55 18.12
3.05 (120") 1.494 2.657 3.08 4.78 3.99 5.89 5.77 9.77 7.52 10.88 10.88 15.35 13.92 21.83
3.81 (150") 1.868 3.321 3.88 6.01 5.02 7.39 7.14 12.14 9.46 13.67 13.67 19.28 17.49 27.40
5.08 (200") 2.491 4.428 5.21 8.05 6.73 9.89 9.42 16.10 12.69 18.33 18.33 25.84 23.43 36.68
6.35 (250") 3.113 5.535 6.55 10.09 8.44 12.39 11.69 20.05 15.92 22.98 22.98 32.40 29.36 45.96
7.62 (300") 3.736 6.641 7.88 12.13 10.16 14.89 13.97 24.00 19.15 27.64 27.64 38.95 35.30 55.24
8.89 (350") 4.358 7.748 9.21 14.17 11.87 17.40 16.25 27.96 22.38 32.29 32.29 45.51 41.24 64.52
10.16 (400") 4.981 8.855 10.54 16.21 13.59 19.90 18.52 31.91 25.60 36.95 36.94 52.07 47.18 73.80
12.70 (500") 6.226 11.069 13.21 20.30 17.01 24.90 23.08 39.82 32.06 46.25 46.25 65.18 59.06 92.36
15.24 (600") 7.472 13.283 15.87 24.38 20.44 29.91 27.63 47.73 38.52 55.56 55.56 78.29 70.94 110.92
17.78 (700") 8.717 15.497 18.54 28.46 23.87 34.91 32.19 55.64 44.98 64.87 64.87 91.41 82.82 129.48
20.32 (800") 9.962 17.710 21.20 32.54 27.30 39.92 36.74 63.55 51.43 74.18 74.18 104.52 94.70 148.04
22.86 (900") 11.207 19.924 23.87 36.63 30.72 44.92 41.30 71.46 57.89 83.49 83.49 117.63 106.58 166.60
25.40 (1000") 12.453 22.138 26.53 40.71 34.15 49.93 45.85 79.37 64.35 92.80 92.80 130.75 118.46 185.16
27.94 (1100") 13.698 24.352 29.19 44.79 37.58 54.93 50.41 87.28 70.80 102.11 102.11 143.86 130.34 203.72
30.48 (1200") 14.943 26.566 31.86 48.87 41.01 59.94 54.96 95.19 77.26 111.42 111.42 156.97 142.22 222.28
33.02 (1300") 16.188 28.779 34.52 52.95 44.44 64.94 59.51 103.10 83.72 120.73 120.73 170.09 154.10 240.84
35.56 (1400") 17.434 30.993 37.19 57.04 47.86 69.95 64.07 111.01 90.17 130.04 130.04 183.20 165.97 259.40
38.10 (1500") 18.679 33.207 39.85 61.12 51.29 74.95 68.62 118.92 96.63 139.35 139.35 196.31 177.85 277.96
*1 The throw ratio is based on the value during projection with the projected image size of 5.08 m (200").
Lens type Zoom Lens
Throw ratio
Projected image size Projection distance (L)
*1
Height
(SH)
Width (SW)
1.18-1.81:1 1.52-2.23:1 2.13-3.63:1 2.87-4.13:1 4.14-5.83:1 5.30-8.28:1
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
Min. (LW)
Max.
(LT)
Min. (LW)
r When the image aspect ratio is 4:3
(Unit: m)
Max.
(LT)
Projection lens Model No. ET-D3QW300 ET-D3QS400 ET-D3QT500 ET-D3QT600 ET-D3QT700 ET-D3QT800
Diagonal (SD)
2.54 (100") 1.524 2.032 3.15 4.88 4.07 6.00 5.88 9.96 7.68 11.10 11.10 15.66 14.15 22.27
3.05 (120") 1.829 2.438 3.80 5.88 4.91 7.23 7.00 11.89 9.26 13.38 13.38 18.87 17.06 26.82
3.81 (150") 2.286 3.048 4.78 7.38 6.17 9.07 8.67 14.80 11.63 16.80 16.80 23.69 21.42 33.63
5.08 (200") 3.048 4.064 6.41 9.88 8.26 12.13 11.45 19.64 15.58 22.49 22.49 31.71 28.69 44.99
6.35 (250") 3.810 5.080 8.04 12.38 10.36 15.19 14.24 24.48 19.53 28.19 28.19 39.74 35.96 56.35
7.62 (300") 4.572 6.096 9.67 14.87 12.46 18.26 17.03 29.32 23.48 33.89 33.89 47.76 43.23 67.70
8.89 (350") 5.334 7.112 11.30 17.37 14.56 21.32 19.82 34.16 27.43 39.58 39.58 55.78 50.50 79.06
10.16 (400") 6.096 8.128 12.93 19.87 16.65 24.38 22.60 39.00 31.39 45.28 45.28 63.81 57.77 90.42
12.70 (500") 7.620 10.160 16.19 24.87 20.85 30.51 28.18 48.68 39.29 56.67 56.67 79.86 72.30 113.13
15.24 (600") 9.144 12.192 19.45 29.86 25.04 36.63 33.75 58.35 47.19 68.07 68.07 95.91 86.84 135.85
17.78 (700") 10.668 14.224 22.71 34.86 29.24 42.76 39.32 68.03 55.09 79.46 79.46 111.95 101.38 158.56
20.32 (800") 12.192 16.256 25.97 39.85 33.44 48.88 44.90 77.71 63.00 90.85 90.85 128.00 115.92 181.28
22.86 (900") 13.716 18.288 29.23 44.85 37.63 55.01 50.47 87.39 70.90 102.25 102.25 144.05 130.46 203.99
25.40 (1000") 15.240 20.320 32.49 49.85 41.83 61.13 56.05 97.07 78.80 113.64 113.64 160.10 145.00 226.70
27.94 (1100") 16.764 22.352 35.76 54.84 46.02 67.26 61.62 106.75 86.70 125.03 125.03 176.15 159.53 249.42
30.48 (1200") 18.288 24.384 39.02 59.84 50.22 73.38 67.19 116.43 94.60 136.43 136.42 192.20 174.07 272.13
33.02 (1300") 19.812 26.416 42.28 64.83 54.41 79.51 72.77 126.11 102.51 147.82 147.82 208.25 188.61 294.85
35.56 (1400") 21.336 28.448 45.54 69.83 58.61 85.63 78.34 135.79 110.41 159.21 159.21 224.29 203.15 317.56
38.10 (1500") 22.860 30.480 48.80 74.82 62.80 91.76 83.92 145.47 118.31 170.60 170.60 240.34 217.69 340.28
*1 The throw ratio is based on the value during projection with the projected image size of 5.08 m (200").
Lens type Zoom Lens
Throw ratio
Projected image size Projection distance (L)
*1
Height
(SH)
Width (SW)
1.58-2.43:1 2.04-2.98:1 2.82-4.83:1 3.84 -5.53:1 5.54-7.80:1 7.06-11.06:1
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
(LW)
(LT)
Min. (LW)
Max.
(LT)
Min. (LW)
Max.
(LT)
46 - ENGLISH
Page 47
Chapter 2 Getting Started — Setting up
Formula for calculating the projection distance per projection lens
To use a projected image size not listed in this manual, check the projected image size SD (m) and use the
respective formula to calculate projection distance.
The unit of all the formulae is m. (Values obtained by the following calculation formulae contain a slight error.) When calculating a projection distance using image size designation (value in inches), multiply the value in inches
by 0.0254 and substitute it into SD in the formula for calculating the projection distance.
r Zoom Lens
Projection lens Model No. Throw ratio Aspect ratio
1.11 - 1.70:1 17:9 = 0.9981 x SD
ET-D3QW300
ET-D3QS400
ET-D3QT500
ET-D3QT600
ET-D3QT700
ET-D3QT800
1.32 - 2.02:1 16:10 = 1.1341 x SD
1.18 - 1.81:1 16:9 = 1.0490 x SD
1.58 - 2.43:1 4:3 = 1.2839 x SD
1.43 - 2.09:1 17:9 = 1.2841 x SD
1.70 - 2.48:1 16:10 = 1.4590 x SD
1.52 - 2.23:1 16:9 = 1.3496 x SD
2.04 - 2.98:1 4:3 = 1.6517 x SD
2.00 - 3.41:1 17:9 = 1.7060 x SD + 0.3072 = 2.9627 x SD + 0.2772
2.36 - 4.03:1 16:10 = 1.9384 x SD + 0.3072 = 3.3663 x SD + 0.2772
2.13 - 3.63:1 16:9 = 1.7931 x SD + 0.3072 = 3.1139 x SD + 0.2772
2.82 - 4.83:1 4:3 = 2.1944 x SD + 0.3072 = 3.8109 x SD + 0.2772
2.69 - 3.88:1 17:9 = 2.4187 x SD
3.19 - 4.60:1 16:10 = 2.7482 x SD
2.87 - 4.13:1 16:9 = 2.5421 x SD
3.84 - 5.53:1 4:3 = 3.1111 x SD
3.89 - 5.47:1 17:9 = 3.4871 x SD
4.61 - 6.49:1 16:10 = 3.9621 x SD
4.14 - 5.83:1 16:9 = 3.6651 x SD
5.54 - 7.80:1 4:3 = 4.4855 x SD
4.97 - 7.76:1 17:9 = 4.4498 x SD
5.89 - 9.21:1 16:10 = 5.0559 x SD
5.30 - 8.28:1 16:9 = 4.6768 x SD
7.06 - 11.06:1 4:3 = 5.7237 x SD
Projection distance (L) formula
Min. (LW) Max. (LT)
-
0.1156 = 1.5291 x SD - 0.1143
-
0.1156 = 1.7374 x SD - 0.1143
-
0.1156 = 1.6072 x SD - 0.1143
-
0.1156 = 1.9669 x SD - 0.1143
-
0.1267 = 1.8748 x SD - 0.1207
-
0.1267 = 2.1302 x SD - 0.1207
-
0.1267 = 1.9705 x SD - 0.1207
-
0.1267 = 2.4115 x SD - 0.1207
-
0.2235 = 3.4871 x SD - 0.2915
-
0.2235 = 3.9621 x SD - 0.2915
-
0.2235 = 3.6651 x SD - 0.2915
-
0.2235 = 4.4855 x SD - 0.2915
-
0.2923 = 4.9121 x SD - 0.3863
-
0.2923 = 5.5812 x SD - 0.3863
-
0.2923 = 5.1627 x SD - 0.3863
-
0.2923 = 6.3184 x SD - 0.3863
-
0.3333 = 6.9524 x SD - 0.4407
-
0.3333 = 7.8994 x SD - 0.4407
-
0.3333 = 7.3071 x SD - 0.4407
-
0.3333 = 8.9427 x SD - 0.4407
ENGLISH - 47
Page 48
Chapter 2 Getting Started — Setting up

Adjusting adjustable feet

Install the projector on a at surface so that the front of the projector is parallel to the screen surface and the
projection screen is rectangular. If the screen is tilted downward, extend the front adjustable feet so that the projected image becomes rectangular.
The adjustable feet can also be used to adjust the projector to be level when it is tilted in the horizontal direction.
Adjustable feet can be extended by turning them as shown in the gure. Turning them in the opposite direction will
return them to the original position.
Maximum adjustable range
Adjustable feet: 20 mm (25/32") each
Attention
f Be careful not to block the intake/exhaust vents with your hands or any objects when adjusting the adjustable feet while the light source is
on. (x page 31)
Note
f The adjustable feet can also be turned by inserting a screwdriver, etc. into the hole (φ8 mm (5/16")) at the side of the adjustable feet.
48 - ENGLISH
Page 49
Chapter 2 Getting Started — Attaching/removing the projection lens (optional)

Attaching/removing the projection lens (optional)

Move the projection lens to the home position before replacing or removing the projection lens. (x page 73)
Attention
f Replace the projection lens after turning off the power of the projector. f Do not touch the electric contacts of the projection lens. Dust or dirt may cause poor contact. f Do not touch the surface of the projection lens with your bare hands. f Before attaching the projection lens, remove the lens cover attached to the projection lens. f Do not touch any area other than specied in “Adjusting the lens mounter when the focus is unbalanced” (x page 75) with the projection
lens removed. Touching around the projection lens mount inside the projector may result in malfunction.
f Panasonic takes no responsibility for any damage or malfunction of the product resulting from the use of projection lenses which are not
manufactured by Panasonic. Be sure to use the specied projection lenses.
Note
f For the adjustment procedure of the focus, zoom, and lens shift after attaching the projector lens, refer to “Adjusting the focus, zoom, and
lens shift” (x page 71).
f For the adjustment procedure of the focus balance in the center and periphery of the projected image when the following projection lens is
used, refer to “Adjusting the focus balance” (x page 72).
g Zoom Lens (Model No.: ET-D3QW300, ET-D3QS400, ET-D3QT500)
f For the adjustment procedure of the focus balance between top, bottom, left, and right of the projected image, refer to “Adjusting the lens
mounter when the focus is unbalanced” (x page 75).

Attaching the projection lens

Attach the projection lens using the following procedure. Start from Step 4) when the lens hole cover is already removed.
Lens hole cover
Guide pins
Ball lock pin
Fig. 1
Guide hole
Ring
Lens lock lever
Fig. 2
Lens lock lever
Fig. 3
Lock pin insertion hole
Ball lock pin
Fig. 4 Fig. 5 Fig. 6
1) Remove the ball lock pin. (Fig. 1)
f Hold the ring of the ball lock pin and pull out in the direction of the arrow.
2) Unlock the lens hole cover. (Fig. 2)
f When unlocking the projection lens, hold the lens hole cover so that it will not drop off from the projector.
ENGLISH - 49
Page 50
Chapter 2 Getting Started — Attaching/removing the projection lens (optional)
f While pulling the lens lock lever forward, slide it counterclockwise towards the “UNLOCK” position.
3) Remove the lens hole cover. (Fig. 3)
4) Attach the projection lens. (Fig. 4)
f Attach the projection lens by aligning the guide holes (two locations) of the projection lens with the guide
pins on the projector.
5) Lock the projection lens. (Fig. 5)
f While pressing the projection lens to the projector side, slide the lens lock lever clockwise towards the
“LOCK” position.
f Conrm that the lens lock lever does not move vertically at the “LOCK” position. If the lens lock lever is in
an incorrect position, the lock may be released unintentionally and the projection lens may fall off from the projector.
6) Attach the ball lock pin. (Fig. 6)
f Insert the ball lock pin all the way in.
Attention
f Store the removed lens hole cover in a safe place. f Turn on the projector and execute the lens calibration after attaching the projection lens. (x page 73)

Removing the projection lens

Remove the projection lens using the following procedure.
Ball lock pin
Ring
Fig. 1
Lens hole cover
Guide pins
Lens lock lever
Fig. 2
Lens lock lever
Fig. 3
Lock pin insertion hole
Ball lock pin
Fig. 4
Fig. 5
Fig. 6
1) Remove the ball lock pin. (Fig. 1)
f Hold the ring of the ball lock pin and pull out in the direction of the arrow.
2) Unlock the projection lens. (Fig. 2)
f When unlocking the projection lens, hold the projection lens so that it will not drop off from the projector. f While pulling the lens lock lever forward, slide it counterclockwise to the “UNLOCK” position.
3) Remove the projection lens. (Fig. 3)
f Proceed to Step 4) when carrying or storing the projector.
50 - ENGLISH
Page 51
Chapter 2 Getting Started — Attaching/removing the projection lens (optional)
4) Attach the supplied lens hole cover. (Fig. 4)
f Attach the lens hole cover by aligning the guide holes (two locations) of the lens hole cover with the guide
pins on the projector.
5) Lock the lens hole cover. (Fig. 5)
f Slide the lens lock lever clockwise towards the “LOCK” position. f Conrm that the lens lock lever does not move vertically at the “LOCK” position.
6) Attach the ball lock pin. (Fig. 6)
f Insert the ball lock pin all the way in.
Attention
f Store the removed projection lens where it will be free from vibration and impact.
ENGLISH - 51
Page 52
Chapter 2 Getting Started — Connecting

Connecting

Before connecting

f Before connecting, carefully read the operating instructions for the external device to be connected. f Turn off the power of all devices before connecting cables. f Connect cables taking care of the following descriptions. Failure to do so may result in malfunctions.
g When connecting a cable to a device connected to the projector or the projector itself, touch any nearby
metallic objects to eliminate static electricity from your body before performing work.
g Do not use unnecessarily long cables to connect a device to the projector or to the projector body. The longer
the cable, the more susceptible to noise it becomes. Since using a cable while it is wound makes it act like an antenna, it is more susceptible to noise.
g When connecting cables, connect GND rst, then insert the connecting terminal of the connecting device in a
straight manner.
f Acquire any connection cable necessary to connect the external device to the system that is neither supplied
with the device nor available as an option.
f Install the Interface Board necessary for the video equipment to connect with the projector to the slot in
advance.
Requesting a qualied technician to install or remove the optional Interface Board is recommended. A
malfunction may occur due to static electricity. Consult your dealer. For details on how to install the Interface Board, refer to “Installing the Interface Board” (x page 294).
f Some computer models or graphic cards are not compatible with the projector. f Connect using an extension device, etc., when installing the projector away from the video equipment. The
projector may not display the image properly when it is connected directly using a long cable.
f For details of the types of video signals that can be used with the projector, refer to “List of compatible signals”
(x page 274).

Connecting example: AV equipment

For <SDI 1 IN>/<SDI 2 IN/1 OUT>/<SDI 3 IN>/<SDI 4 IN/3 OUT> terminals of the Interface Board
This is an example when using the Interface Board for 12G-SDI (Model No.: ET-MDN12G10) installed in
<SLOT 1>.
12G-SDI signal output compatible device
HD-SDI signal, 3G-SDI signal, 6G-SDI signal, or 12G-SDI signal
Note
f Use a connection cable of 5C-FB or higher (such as 5C-FB, or 7C-FB), Belden 1694A or higher, or L-5.5CUHD manufactured by Canare
Electric Co., Ltd. to properly transmit images. The maximum cable length that can be used is as follows. However, this maximum cable length is a rough guideline, and does not guarantee the transmission distance.
g HD-SDI signal, 3G-SDI signal: 150 m (492'2") g 6G-SDI signal: 80 m (262'6") (When L-5.5CUHD is used, the cable length should be 110 m (360'11").) g For 12G-SDI signal, the cable length will differ depending on the setting in the [DISPLAY OPTION] menu [SLOT IN] [SDI MODE].
When [SDI MODE] is set to [INPUT]: 50 m (164'1") (When L-5.5CUHD is used, the cable length should be 100 m (328'1").) When [SDI MODE] is set to [OUTPUT]: 50 m (164'1") (When L-5.5CUHD is used, the cable length should be 90 m (295'3").)
f When the [DISPLAY OPTION] menu [SLOT IN] [SDI MODE] is set to [OUTPUT], attach a terminating resistor (75 Ω) to the terminal
with no device connected as an output destination.
52 - ENGLISH
Page 53
Chapter 2 Getting Started — Connecting
f Use the BNC connector that is compatible with the coaxial cable and type of the signal to be used. f Setting the [DISPLAY OPTION] menu [SLOT IN] is required depending on the connected external device or the input signal. f Setting the [DISPLAY OPTION] menu [SLOT IN] [SDI LINK] is required when the dual link signal or the quad link signal is input. f To input the dual link signal, use the cable with same length and same type for connecting to the <SDI 1 IN> terminal and the <SDI 3 IN>
terminal. The image may not be projected correctly when the difference of the cable length is 4 m (13'1") or more.
f To input the quad link signal, use the cable with same length and same type for connecting to each of <SDI 1 IN>/<SDI 2 IN/1 OUT>/<SDI 3
IN>/<SDI 4 IN/3 OUT> terminals. The image may not be projected correctly when the difference of the cable length is 4 m (13'1") or more.
f Directly connect the projector with the external device that will output the signal without going through a distributor, etc., when inputting dual
link signals. A phase difference is generated between the Link A signal and the Link B signal, and the image may not be projected correctly.
f Directly connect the projector with the external device that will output the signal without going through a distributor, etc., when inputting quad
link signals. A phase difference is generated between the signals of Link 1, Link 2, Link 3, and Link 4, and the image may not be projected correctly.
f An error in signal detection may occur when an unsteady signal is input to the projector. In such case, set the [DISPLAY OPTION] menu
[SLOT IN] to the content corresponding to the input signal. f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal. f To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu [SLOT
IN] [SDI MODE] to [OUTPUT].
For <HDMI IN 1>/<HDMI IN 2> terminals and <HDMI IN 3>/<HDMI IN 4> terminals of the Interface Board
This is an example when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed in
<SLOT 2>.
Blu-ray disc player
Note
f For the HDMI cable, use an HDMI High Speed cable that conforms to the HDMI standards. However, when the following 4K video signal
exceeding the supported transmission speed of the HDMI High Speed cable is to be input, use the HDMI cable supporting the high speed
transmission of 18 Gbps such as the one with Premium HDMI cable authentication.
g A video signal with high specication color depth and gradation such as 3840 x 2160/60p 4:2:2/36-bit or 3840 x 2160/60p 4:4:4/24-bit
Images may be disrupted or may not be projected when a video signal exceeding the supported transmission speed of the HDMI cable is
used. f Setting the [DISPLAY OPTION] menu [SLOT IN] is required depending on the connected external device or the input signal.
Setting the [DISPLAY OPTION] menu [SLOT IN] [HDMI LINK] is required when the dual link signal or the quad link signal is input. f The <HDMI IN 1>/<HDMI IN 2>/<HDMI IN 3>/<HDMI IN 4> terminals can be connected to the external device with a DVI-D terminal by
using the HDMI/DVI conversion cable. However, this may not function properly for some external devices, and image may not be projected. f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI
2 input (Model No.: ET-MDNHM10), it is necessary for the rmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the
version is earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding
the version update to the latest rmware.
For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board” (x page 36).
f The projector does not support VIERA Link (HDMI) and HDMI CEC (Consumer Electronics Control).
ENGLISH - 53
Page 54
Chapter 2 Getting Started — Connecting
For <DVI-D IN 1>/<DVI-D IN 2> terminals and <DVI-D IN 3>/<DVI-D IN 4> terminals of the Interface Board
This is an example when the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed in
<SLOT 2>.
DVD player with HDMI terminal (HDCP)
Note
f Setting the [DISPLAY OPTION] menu [SLOT IN] is required depending on the connected external device or the input signal.
Setting the [DISPLAY OPTION] menu [SLOT IN] [DVI-D LINK] is required when the dual link signal or the quad link signal is input. f The <DVI-D IN 1>/<DVI-D IN 2>/<DVI-D IN 3>/<DVI-D IN 4> terminals can be connected with the HDMI and DVI-D compatible device.
However, some external devices may not be able to project images properly, such as the image not displaying.

Connecting example: Computers

This is an example when the optional Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10) is installed in <SLOT 1>, and the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed
in <SLOT 2>.
Control computer
Computer
Computer
Control computer
Attention
f When connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially
available shielded cables.
Note
f Setting the [DISPLAY OPTION] menu [SLOT IN] is required depending on the connected external device or the input signal. f For the DisplayPort cable, use a DisplayPort cable that conforms to the DisplayPort standards. When a cable that does not conform to the
DisplayPort standards is used, images may be interrupted or may not be projected.
54 - ENGLISH
Page 55
Chapter 2 Getting Started — Connecting
f The <DVI-D IN 1>/<DVI-D IN 2>/<DVI-D IN 3>/<DVI-D IN 4> terminals support the single link for DVI 1.0. They do not support the dual link
for DVI 1.0. f For the HDMI cable, use an HDMI High Speed cable that conforms to the HDMI standards. However, when the following 4K video signal
exceeding the supported transmission speed of the HDMI High Speed cable is to be input, use the HDMI cable supporting the high speed
transmission of 18 Gbps such as the one with Premium HDMI cable authentication.
g A video signal with high specication color depth and gradation such as 3840 x 2160/60p 4:2:2/36-bit or 3840 x 2160/60p 4:4:4/24-bit
Images may be disrupted or may not be projected when a video signal exceeding the supported transmission speed of the HDMI cable is
used. f The <HDMI IN 1>/<HDMI IN 2>/<HDMI IN 3>/<HDMI IN 4> terminals can be connected to the external device with a DVI-D terminal by
using the HDMI/DVI conversion cable. However, this may not function properly for some external devices, and image may not be projected. f If you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume feature to operate
the projector.

Connecting example using DIGITAL LINK

Twisted-pair-cable transmitters based on the communication standard HDBaseTTM such as the optional DIGITAL
LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) use the twisted pair cable to transmit
input images, Ethernet, and serial control signal, and the projector can input such digital signal to the <DIGITAL LINK> terminal.
Projector connecting terminals
Computer
Computer cable
Example of twisted-pair-cable transmitter
(commercially available)
HDMI cable (commercially available)
Hub
VCR
Control computer
*1 Control target is the projector or the twisted-pair-cable transmitter. The control itself may not be possible depending on the twisted-pair-cable
transmitter. Check the operating instructions of the device to be connected.
*1
(with built-in TBC)
Blu-ray disc player
Attention
f Always use one of the following when connecting a VCR.
g Use a VCR with built-in time base corrector (TBC). g Use a time base corrector (TBC) between the projector and the VCR.
f If nonstandard burst signals are connected, the image may be disrupted. In such a case, connect the time base corrector (TBC) between
the projector and the external devices. f Ask a qualied technician or your dealer to install the cable wiring between the twisted-pair-cable transmitter and the projector. Image may
be disrupted if cable transmission characteristics cannot be obtained due to inadequate installation. f For the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:
g Conforming to CAT5e or higher standards g Shielded type (including connectors) g Straight-through g Single wire g Diameter of the cable core is same or larger than AWG24 (AWG24, AWG23, etc.)
f When laying cables between the twisted-pair-cable transmitter and the projector, conrm that cable characteristics are compatible with
CAT5e or higher using tools such as a cable tester or cable analyzer.
When a relay connector is used, include it in the measurement. f Do not use a hub between the twisted-pair-cable transmitter and the projector. f When connecting to the projector using a twisted-pair-cable transmitter (receiver) of other manufacturers, do not place another twisted-pair-
cable transmitter between the twisted-pair-cable transmitter of other manufacturers and the projector. This may cause image to be disrupted. f To transmit the Ethernet and serial control signals using the <DIGITAL LINK> terminal, set the [NETWORK] menu [NETWORK
CONTROL] [TYPE SELECT] to [DIGITAL LINK] or [LAN & DIGITAL LINK]. f To transmit the Ethernet signal using the <LAN> terminal, set the [NETWORK] menu [NETWORK CONTROL] [TYPE SELECT] to
[LAN] or [LAN & DIGITAL LINK].
ENGLISH - 55
Page 56
Chapter 2 Getting Started — Connecting
f The <DIGITAL LINK> terminal and the <LAN> terminal are connected inside of the projector when the [NETWORK] menu [NETWORK
CONTROL] [TYPE SELECT] is set to [LAN & DIGITAL LINK]. Do not directly connect the <DIGITAL LINK> terminal and the <LAN>
terminal using a LAN cable. Construct the system so that it is not connected to the same network via the peripherals such as the hub or the
twisted-pair-cable transmitter. f Do not pull cables forcefully. Also, do not bend or fold cables unnecessarily. f To reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector
without any loops. f Lay the cables between the twisted-pair-cable transmitter and the projector away from other cables, particularly power cables. f When laying multiple cables, run them side by side along the shortest distance possible without bundling them together. f After laying the cables, go to the [NETWORK] menu [DIGITAL LINK STATUS] and conrm that the value of [SIGNAL QUALITY] is
displayed in green which indicates normal quality. (x page 191)
Note
f For the HDMI cable, use an HDMI High Speed cable that conforms to the HDMI standards. If a cable that does not conform to the HDMI
standards is used, images may be interrupted or may not be projected. f The projector does not support VIERA Link (HDMI) and HDMI CEC (Consumer Electronics Control). f The optional Digital Interface Box (Model No.: ET-YFB100G) and the optional DIGITAL LINK Switcher (Model No.: ET-YFB200G) do not
support the input and output of the 4K video signal. f The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1") for the signal with
resolution of 1 920 x 1 200 dots or less. For the signal with the resolution exceeding 1 920 x 1 200 dots, the maximum transmission distance
is 50 m (164'1"). It is possible to transmit up to 150 m (492'2") if the twisted-pair-cable transmitter supports the long-reach communication
method. However, the signal that the projector can receive is only up to 1080/60p (1 920 x 1 080 dots, dot clock frequency 148.5 MHz)
for the long-reach communication method. If these distances are exceeded, image may be disrupted or a malfunction may occur in LAN
communication. Please note that Panasonic does not support the use of the projector outside the maximum transmission distance. When
connecting with the long reach, video signal or distance that can be transmitted may be restricted, depending on the specication of the
twisted-pair-cable transmitter. f For twisted-pair-cable transmitters of other manufacturers of which the operation has been veried with the projector, visit the Panasonic
website (https://panasonic.net/cns/projector/). Note that the verication for devices of other manufacturers has been made for the items set
by Panasonic Corporation, and not all the operations have been veried. For operation or performance problems caused by the devices of
other manufacturers, contact the respective manufacturers.

Connecting example when using the contrast synchronization function/shutter synchronization function

In a case to construct a multi-display by linking projected images from multiple projectors, following functions can be used by synchronizing multiple projectors using the <MULTI PROJECTOR SYNC IN> terminal and the <MULTI PROJECTOR SYNC OUT> terminal.
f Contrast synchronization function
A linked screen with balanced contrast can be displayed by sharing the brightness level of the video signal
being input to each projector.
To use this function, set the [PROJECTOR SETUP] menu [MULTI PROJECTOR SYNC] for each
synchronized projector as follows.
g Set [MULTI PROJECTOR SYNC] [MODE] to anything other than [OFF].
Set [MODE] to [MASTER] only on one projector that is synchronized. Set [MODE] to [SLAVE] for all other projectors.
g Set [MULTI PROJECTOR SYNC] [CONTRAST SYNC] to [ON].
f Shutter synchronization function
This is a function to synchronize the shutter operation of the specied projector to other projectors, and the
effect using the shutter function including the fade in/fade out operation can be synchronized.
To use this function, set the [PROJECTOR SETUP] menu [MULTI PROJECTOR SYNC] for each
synchronized projector as follows.
g Set [MULTI PROJECTOR SYNC] [MODE] to anything other than [OFF].
Set [MODE] to [MASTER] only on one projector that becomes the synchronization source within the linked projectors. Set [MODE] to [SLAVE] for all other projectors.
g Set [MULTI PROJECTOR SYNC] [SHUTTER SYNC] to [ON].
56 - ENGLISH
Page 57
Chapter 2 Getting Started — Connecting
Connecting example
Connect all the projectors to be linked in a loop by daisy chain connection when using the contrast synchronization function/shutter synchronization function. The number of linked projectors is limited to the maximum of 64 projectors.
Connecting terminals of the synchronization source
Connecting terminals of the projector to synchronize
Connecting terminals of the projector to synchronize
Connecting terminals of the projector to synchronize
Note
f The contrast synchronization function and the shutter synchronization function can be used simultaneously. f For details on the settings of the contrast synchronization function and the shutter synchronization function, refer to the [PROJECTOR
SETUP] menu [MULTI PROJECTOR SYNC] (x page 168). f The menu items in the [PROJECTOR SETUP] menu [MULTI PROJECTOR SYNC] is the same as the following setting items.
g The [PICTURE] menu [DYNAMIC CONTRAST] [USER] [MULTI PROJECTOR SYNC] g The [DISPLAY OPTION] menu [SHUTTER SETTING] [MULTI PROJECTOR SYNC]
f If there are any projectors which you do not want to synchronize within the linked projectors, set [CONTRAST SYNC] and [SHUTTER
SYNC] to [OFF] individually. f The shutter synchronization function will operate even when there are different models within the linked projectors. However, the
synchronization function will not operate when there is a DLP projector that is constructed with one DLP chip such as PT-RCQ10 series
within the linked projectors.
ENGLISH - 57
Page 58

Chapter 3 Basic Operations

This chapter describes basic operations to start with.
58 - ENGLISH
Page 59
Chapter 3 Basic Operations — Switching on/off the projector

Switching on/off the projector

Connecting the power cord

Conrm that the <MAIN POWER> switch is on the <OFF> side before connecting the supplied power cord.
Use the power cord matching with the power supply voltage and the shape of the outlet.
For details of power cord handling, refer to “Read this rst!” (x page 5). For the shape of the outlet, refer to “Usable outlet” (x page 40).
Attention
f The <AC IN> terminal on the side of the projector and the connector of the supplied power cord are not hot swapping compatible. Make
sure to attach the power cord to the projector rst, and then connect the power plug to the outlet. When removing the power cord from the
projector, make sure to remove the power plug from the outlet rst.
Note
f The light output will decrease to approximately 1/5 when using the projector with AC 100 V to AC 120 V. f The supplied power cords vary depending on the country or region where you purchased the product.
How to attach the power cord
Fig. 2Fig. 1
1) Check the shapes of the <AC IN> terminal on the side of the projector and the power cord connector, then insert the connector completely in the correct direction. (Fig. 1)
2) While inserting the power cord connector into the projector, turn clockwise until it clicks. (Fig. 2)
How to remove the power cord
Lock lever
Fig. 1 Fig. 2
1) Confirm that the <MAIN POWER> switch on the side of the projector is on the <OFF> side, and remove the power plug from the outlet.
2) Turn the power cord connector counterclockwise while sliding the lock lever forward (Fig. 1), and remove the connector from the <AC IN> terminal on the projector (Fig. 2).
ENGLISH - 59
Page 60
Chapter 3 Basic Operations — Switching on/off the projector

Power indicator

Indicate the status of the power. Check the status of the power indicator <ON (G)/STANDBY (R)> before operating
the projector.
Power indicator <ON (G)/STANDBY (R)>
Indicator status Projector status
Off The main power is switched off.
The power is switched off. (standby mode)
Lit
Red
Blinking
Green Lit Projecting.
Orange Lit
Projection will start when the power on <b> button is pressed.
f The projector may not operate when the light source indicators <LIGHT1>/<LIGHT2>
or the temperature indicator <TEMP> are blinking. (x page 251)
The output image equivalent to the projected image from the projector is being viewed using the web control function. Refer to “[Remote preview] page” (x page 205) for details.
The projector is preparing to switch off the projector.
The power is switched off after a while. (Changes to the standby mode.)
Note
f While the power indicator <ON (G)/STANDBY (R)> lights in orange, the fan is running to cool the projector. f The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lit in red). Refer to “Power consumption”
(x page 290) for the power consumption.
f When the projector receives the signal from the remote control, the power indicator <ON (G)/STANDBY (R)> will blink in the following color
according to the status of the projector.
g When the projector is in projection mode: Green g When the projector is in standby mode: Orange
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the shutter function is in use (shutter: closed), or while the
function of the [PROJECTOR SETUP] menu [NO SIGNAL SETTING] [NO SIGNAL LIGHTS-OUT] (x page 164) is operating and the light source is turned off.
60 - ENGLISH
Page 61
Chapter 3 Basic Operations — Switching on/off the projector

Switching on the projector

Install the projection lens before switching on the projector.
Remove the lens cover rst.
4)
3)
2)
1)
4)
1) Connect the power cord to the projector.
2) Connect the power plug to an outlet.
3) Press the handle of the <MAIN POWER> switch to the <ON> side to turn on the power.
f The power indicator <ON (G)/STANDBY (R)> lights in red, and the projector enters the standby mode.
4) Press the power on <b> button.
f The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Attention
f Always remove the lens cover before starting the projection. Projecting continuously while the lens cover is attached may cause the lens
cover to heat up and result in a re.
Note
f A warm-up period of up to approximately ve minutes may be necessary until an image is displayed when the projector is switched on at
around 0 °C (32 °F).
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP> turns off and the projection starts. Refer to “When an indicator lights up” (x page 251) for the indicator status display.
f If the operating environment temperature is low and warm-up takes more than ve minutes, the projector will judge that a problem has
occurred and the power will automatically be set to standby mode. In such case, increase the operating environment temperature to 0 °C
(32 °F) or higher, turn off the main power, and then turn on the power again.
f If the power was turned off during projection at the previous use by setting the <MAIN POWER> switch to <OFF> or by using the breaker
directly while projecting, the power indicator <ON (G)/STANDBY (R)> lights up in green and an image is projected after a while when the
power is turned on by setting the <MAIN POWER> switch to <ON> or by turning the breaker on with the power plug connected to the outlet. This applies only when the [PROJECTOR SETUP] menu [INITIAL STARTUP] is set to [LAST MEMORY].
f The light output will decrease to approximately 1/5 when using the projector with AC 100 V to AC 120 V.
ENGLISH - 61
Page 62
Chapter 3 Basic Operations — Switching on/off the projector

When the initial setting screen is displayed

When the projector is switched on for the rst time after purchase, or when the [PROJECTOR SETUP] menu [INITIALIZE] [FACTORY RESET] is executed, the focus adjustment screen is displayed after projection starts, and then the [INITIAL SETTING] screen is displayed. Set them according to the circumstances.
In other occasions, you can change the settings by menu operations. If you press the <MENU> button while the [INITIAL SETTING] screen is displayed, you can go back to the
previous screen.
Focus adjustment
Adjust the focus to display the menu screen clearly. You may also need to adjust the zoom and lens shift. Refer to “Adjusting the focus, zoom, and lens shift” (x page 71) for details.
1) Press asqw to adjust the focus.
LENS
FOCUS
FOCUS POSITION
ADJUST
2) Press the <MENU> button to proceed to the initial setting.
52
Initial setting (display language)
Select the language to show on the screen. After completed the initial setting, you can change the display language from the [DISPLAY LANGUAGE] menu.
1) Press as to select the display language.
INITIAL SETTING
Please select DISPLAY LANGUAGE.
SELECT
ENTER
SET
2) Press the <ENTER> button to proceed to the initial setting.
1/6
62 - ENGLISH
Page 63
Chapter 3 Basic Operations — Switching on/off the projector
Initial setting (operation setting)
Set the items for the operating method depending on the projector’s application and duration of usage.
After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP] menu [OPERATION SETTING]. If you change the settings while using the projector, the duration until the brightness decreases to half may shorten or the brightness may decrease.
This initial setting (operation setting) is prepared to complete the settings simply at once during the installation
when the operation of the projector is predetermined. This cannot set all the items regarding the operation setting. When the detailed setting is required or setting change is required, ask the person responsible for this projector
(such as a person in charge of equipment or operation).
INITIAL SETTING
OPERATING MODE
LIGHT OUTPUT
Set the way to use the projector. For details, please refer to the operating instructions "When the initial setting screen is displayed".
NORMAL
2/6
100.0%
ENTER
SET
CHANGEMENU SELECT
Note
f For the relationship between the brightness and the runtime, refer to “Relationship between brightness and runtime” (x page 64). f For details on each setting item, refer to the [PROJECTOR SETUP] menu [OPERATION SETTING].
1) Press as to select [OPERATING MODE].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[NORMAL]
[ECO]
[USER1]
[USER3]
*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the
[PICTURE] menu [DYNAMIC CONTRAST] set to [3] and under environment of 0.15 mg/m3 dust. The value of runtime is just an estimate, and is not the warranty period.
Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours
*1
or more
.
The brightness will decrease compared to [NORMAL], but set this item to prioritize the life of the light
*1
source. The estimated runtime is approximately 24 000 hours or more
.
Set [LIGHT OUTPUT] as desired.[USER2]
3) Press as to select [LIGHT OUTPUT].
4) Press qw to adjust.
Operation
Press w. Press q.
Brightness Runtime
The screen becomes brighter. The runtime becomes shorter. The screen becomes darker. The runtime becomes longer.
Adjustment
5) Press the <ENTER> button to proceed to the initial setting.
Range of adjustment
8.0 % - 100.0 %
ENGLISH - 63
Page 64
Chapter 3 Basic Operations — Switching on/off the projector
Relationship between brightness and runtime
The projector can be operated with arbitrary brightness and runtime by setting [LIGHT OUTPUT] to desired setting.
The relationship between the [LIGHT OUTPUT] setting, brightness, and the estimated runtime is as follows. Make
the initial setting (operation setting) depending on the desired brightness of the projected image and runtime.
The values of the brightness and the runtime are just an estimate, and the graph indicating the relationship is just an example. Also, these do not indicate the warranty period.
[LIGHT OUTPUT] (%) Brightness (lm) Estimated runtime*1 (hours)
100.0 50 000 27 000
80.0 40 000 39 500
70.0 35 000 47 500
60.0 30 000 56 500
50.0 25 000 66 500
*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the
[PICTURE] menu [DYNAMIC CONTRAST] set to [3] and under environment of 0.15 mg/m3 dust.
100.0
90.0
80.0
70.0
60.0
50.0
40.0
[LIGHT OUTPUT] (%)
50 000
25 000
66 50058 60050 70042 80034 90027 000
Brightness (lm)
Estimated runtime (hours)
Note
f Under inuence of characteristics of each light source, conditions of use, installation environment, etc., the runtime may be shorter than the
estimation.
f If the consolidated runtime of the projector exceeds 20 000 hours, replacement of the components inside the projector may be required. The
consolidated runtime can be conrmed in the [STATUS] screen. Refer to the [PROJECTOR SETUP] menu [STATUS] for details.
f After completed the initial setting, the wider the combination of luminance and runtime becomes by setting the [PROJECTOR SETUP]
menu [BRIGHTNESS CONTROL] [BRIGHTNESS CONTROL SETUP] [CONSTANT MODE] to [AUTO] or [PC]. Refer to the [PROJECTOR SETUP] menu [BRIGHTNESS CONTROL] for details.
Initial setting (installation setting)
Set [FRONT/REAR] and [FLOOR/CEILING] in [PROJECTION METHOD] depending on the installation mode. Refer to “Installation mode” (x page 40) for details.
After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu [PROJECTION METHOD].
1) Press qw to switch the setting.
INITIAL SETTING
PROJECTION METHOD
FRONT/REAR
FLOOR/CEILING
Change the projection method (FRONT/REAR, FLOOR/CEILING) if the screen display is upside down or inverted.
3/6
FRONT
AUTO
MENU SELECT
ENTER
SET
CHANGE
2) Press the <ENTER> button to proceed to the initial setting.
64 - ENGLISH
Page 65
Chapter 3 Basic Operations — Switching on/off the projector
Initial setting (screen setting)
Set the screen format (aspect ratio) and display position of the image.
After completed the initial setting, you can change the settings of each item from the [DISPLAY OPTION] menu [SCREEN SETTING].
1) Press qw to switch the setting.
f The setting will change each time you press the button.
INITIAL SETTING
SCREEN FORMAT
SCREEN POSITION
Set as necessary for the screen in use.
4/6
17:9
ENTER
SET
CHANGEMENU SELECT
2) Press as to select [SCREEN POSITION].
f [SCREEN POSITION] cannot be selected or adjusted when [SCREEN FORMAT] is set to [17:9].
3) Press qw to adjust.
INITIAL SETTING
SCREEN FORMAT
SCREEN POSITION
Set as necessary for the screen in use.
MENU SELECT
ENTER
SET
CHANGE
4/6
16:9
0
4) Press the <ENTER> button to proceed to the initial setting.
ENGLISH - 65
Page 66
Chapter 3 Basic Operations — Switching on/off the projector
Initial setting (time zone)
Set [TIME ZONE] in accordance with the country or region where you use the projector. After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu [DATE
AND TIME]. The current settings are displayed in [LOCAL DATE] and [LOCAL TIME].
1) Press qw to switch the setting.
INITIAL SETTING
TIME ZONE
LOCAL DATE
LOCAL TIME
Please set up a time zone according to the area of your country or region.
CHANGE
ENTER
SET
20XX/01/01
123456
2) Press the <ENTER> button to proceed to the initial setting.
Note
5/6
+09:00
f In the factory default setting, the time zone of the projector is set to +09:00 (Japan and Korea Standard Time). Change the setting of the
[PROJECTOR SETUP] menu [DATE AND TIME] [TIME ZONE] to the time zone of the region where you use the projector.
Initial setting (date and time)
Set the local date and time. After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu [DATE
AND TIME]. To set the date and time automatically, refer to “Setting the date and time automatically” (x page 166).
1) Press as to select an item.
2) Press qw to switch the setting.
INITIAL SETTING
YEAR
MONTH
DAY
HOUR
MINUTE
SECOND
Please set the date and time of the built-in clock of the projector.
ENTER
SET
CHANGEMENU SELECT
6/6
20XX
1
1
12
34
56
3) Press the <ENTER> button.
f Conrm the setting value and complete the initial setting.
66 - ENGLISH
Page 67
Chapter 3 Basic Operations — Switching on/off the projector

Making adjustments and selections

It is recommended to perform the focus adjustment after 30 minutes have elapsed with the focus test pattern displayed. For details of the test pattern, refer to “[TEST PATTERN] menu” (x page 181). To use the active focus optimizer function, set the [PROJECTOR SETUP] menu [LENS] [ACTIVE FOCUS OPTIMIZER] [ACTIVE FOCUS] to [ON], and then adjust the focus. (x page 148)
1) 6) 7) 8) 9)2) 3)
4)
2) 3)
1) 8)
4)
5)
6)
7) 9)
1) Press the <FOCUS> button to roughly adjust the focus of the projected image. (x page 71)
2) Change the setting of the [PROJECTOR SETUP] menu [PROJECTION METHOD] depending on the installation mode. (x page 40)
f Refer to “Navigating through the menu” (x page 84) for the operation of the menu screen.
3) Execute the lens calibration.
f Execute the lens calibration when using the projector for the rst time after attaching the projection lens.
(x page 73)
4) Select the input by pressing the input selection button on the remote control or the control panel.
f The buttons that can be used on the remote control or the control panel are as follows.
Remote control:
<SDI> button, <DIGITAL LINK> button, <HDMI> button, <DVI-D> button, <DISPLAYPORT> button, <SLOT 1> button, <SLOT 2> button
Control panel:
<DIGITAL LINK> button, <SLOT 1> button, <SLOT 2> button
f For details of operation for input selection, refer to “Selecting the input signal” (x page 69).
5) Adjust the front, back and sideway tilt of the projector with the adjustable feet. (x page 48)
6) Press the <SHIFT> button to adjust the position of the projected image.
7) Press the <ZOOM> button to match the projected image size to the screen.
8) Press the <FOCUS> button again to adjust the focus.
9) Press the <ZOOM> button again to adjust the zoom and match the projected image size to the screen.
Note
f When the projector is switched on for the rst time after purchase, or when the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY
RESET] is executed, the focus adjustment screen is displayed after projection starts, and then the [INITIAL SETTING] screen is displayed. For details, refer to “When the initial setting screen is displayed” (x page 62).
ENGLISH - 67
Page 68
Chapter 3 Basic Operations — Switching on/off the projector

Switching off the projector

3)
4)
1)
2)
1)
2)
1) Press the power standby <v> button.
f The [POWER OFF(STANDBY)] conrmation screen is displayed.
2) Press qw to select [OK], and press the <ENTER> button. (Or press the power standby <v> button again.)
f Projection of the image will stop, and the power indicator <ON (G)/STANDBY (R)> on the projector body
lights in orange. (The fan keeps running.)
3) Wait for a few seconds until the power indicator <ON (G)/STANDBY (R)> of the projector body lights up in red (fan is stopped).
4) Press the handle of the <MAIN POWER> switch to the <OFF> side to turn off the power.
Attention
f When switching off the projector, make sure to follow the procedures described. Failure to do so may damage the internal components and
result in malfunctions.
Note
f Even when the power standby <v> button is pressed and the projector is switched off, the projector consumes power if the main
power of the projector is on.
f The <MAIN POWER> switch of the projector is equipped with an overcurrent protection function. When current exceeding 30 A is detected,
the overcurrent is automatically disconnected and the circuit in the switch will become open. Ask your dealer for repair when the overcurrent protection function has operated.
68 - ENGLISH
Page 69
Chapter 3 Basic Operations — Projecting

Projecting

Check the projection lens attachment (x page 49), external device connection (x page 52), and power cord connection (x page 59), and then switch on the power (x page 61) to start projecting. Select the video for
projection, and adjust appearance of the projected image.

Selecting the input signal

The input of the image to project can be switched. Method to switch the input is as follows.
f Press the input selection button on the remote control and directly specify the input of the image to project. f Press the input selection button on the control panel and directly specify the input of the image to project. f Display the input selection screen and select the input of the image to project from the list.
Remote control Control panel
Switching the input directly with the remote control
The input of the image to project can be switched by directly specifying it with the input selection button on the remote control.
1) Press the input selection button (<HDMI>, <DISPLAYPORT>, <DVI-D>, <SDI>, <SLOT 1>, <SLOT 2>, <DIGITAL LINK>).
Switches the input to HDMI. This can be operated when the optional Interface Board equipped with the HDMI input is installed in
<HDMI>
<DISPLAYPORT>
<DVI-D>
<SDI>
<SLOT 1>
<SLOT 2>
<DIGITAL LINK>
the slot. The input is switched every time the button is pressed when one of the HDMI inputs is selected on the installed optional Interface Board.
Switches the input to DisplayPort. This can be operated when the optional Interface Board equipped with the DisplayPort input is installed in the slot. The input is switched every time the button is pressed when one of the DisplayPort inputs is selected on the installed optional Interface Board.
Switches the input to DVI-D. This can be operated when the optional Interface Board equipped with the DVI-D input is installed in the slot. The input is switched every time the button is pressed when one of the DVI-D inputs is selected on the installed optional Interface Board.
Switches the input to SDI. This can be operated when the optional Interface Board equipped with the SDI input is installed in the slot. The input is switched every time the button is pressed when one of the SDI inputs is selected on the installed optional Interface Board.
Switches the input to the signal of the optional Interface Board installed in <SLOT 1>. The input is switched every time the button is pressed when one of the inputs is selected on the installed optional Interface Board.
Switches the input to the signal of the optional Interface Board installed in <SLOT 2>. The input is switched every time the button is pressed when one of the inputs is selected on the installed optional Interface Board.
Switches the input to DIGITAL LINK. The image of the signal input to the <DIGITAL LINK> terminal is projected.
Attention
f Images may not be projected properly depending on the external device, or the Blu-ray disc or DVD disc, to be played back.
Set the [PICTURE] menu [SYSTEM SELECTOR]. When the SDI signal is input, set the [DISPLAY OPTION] menu [SLOT IN].
ENGLISH - 69
Page 70
Chapter 3 Basic Operations — Projecting
f Conrm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from the [POSITION] menu
[ASPECT].
Note
f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK>
terminal, the input on the DIGITAL LINK output supported device changes each time the <DIGITAL LINK> button is pressed. The input can also be changed using the RS-232C control command. For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGITAL LINK, and then switch the input on the twisted-pair-cable transmitter.
f <HDMI> button, <DISPLAYPORT> button, <DVI-D> button, <SLOT 1> button, and <SLOT 2> button can be used when the optional
Interface Board equipped with corresponding input is installed in the slot.
f The operation when the <HDMI> button, <DISPLAYPORT> button, <DVI-D> button, <SDI> button, <SLOT 1> button, or <SLOT 2> button is
pressed can be xed to operation to switch to the specied input using the [SECURITY] menu → [CONTROL DEVICE SETUP].
Switching the input directly with the control panel
The input of the image to project can be switched by directly specifying it with the input selection button on the control panel.
1) Press the input selection button (<SLOT 1>, <SLOT 2>, <DIGITAL LINK>).
Switches the input to the signal of the optional Interface Board installed in <SLOT 1>.
<SLOT 1>
<SLOT 2>
<DIGITAL LINK>
The input is switched every time the button is pressed when one of the inputs is selected on the installed optional Interface Board.
Switches the input to the signal of the optional Interface Board installed in <SLOT 2>. The input is switched every time the button is pressed when one of the inputs is selected on the installed optional Interface Board.
Switches the input to DIGITAL LINK. The image of the signal input to the <DIGITAL LINK> terminal is projected.
Attention
f Images may not be projected properly depending on the external device, or the Blu-ray disc or DVD disc, to be played back.
Set the [PICTURE] menu [SYSTEM SELECTOR]. When the SDI signal is input, set the [DISPLAY OPTION] menu [SLOT IN].
f Conrm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from the [POSITION] menu
[ASPECT].
Note
f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK>
terminal, the input on the DIGITAL LINK output supported device changes each time the <DIGITAL LINK> button is pressed. The input can also be changed using the RS-232C control command. For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGITAL LINK, and then switch the input on the twisted-pair-cable transmitter.
f The <SLOT 1> button and the <SLOT 2> button can be used when the optional Interface Board equipped with corresponding input is
installed in the slot.
f The operation when the <SLOT 1> button or the <SLOT 2> button is pressed can be xed to operation to switch to the specied input using
the [SECURITY] menu [CONTROL DEVICE SETUP].
70 - ENGLISH
Page 71
Chapter 3 Basic Operations — Projecting
Switching the input by displaying the input selection screen
The input of the image for projection can be selected by displaying the input selection screen.
1) Press the <INPUT MENU> button on the remote control or control panel.
f The input selection screen is displayed.
Following input selection screen is an example when the Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>, and the optional Interface Board for HDMI 2 input (Model No.:
ET-MDNHM10) is installed in <SLOT 2>.
INPUT SELECT
SDI1 [SLOT1]
SDI2 [SLOT1]
SDI3 [SLOT1]
SDI4 [SLOT1]
HDMI3 [SLOT2]
HDMI4 [SLOT2]
DIGITAL LINK
SELECT
ENTER
SET
2) Press the <INPUT MENU> button again.
f The input will switch each time you press the <INPUT MENU> button.
Note
f Input can be switched by pressing as to select the input of the image for projection and pressing the <ENTER> button while the input
selection screen is displayed.
f If the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, the input
selection menu for the DIGITAL LINK output supported device is displayed when the <ENTER> button is pressed while the DIGITAL LINK input is selected in the input selection screen.
f If the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, the DIGITAL
LINK logo and the input name selected in the DIGITAL LINK output supported device are displayed in the display section of the [DIGITAL LINK] in the input selection screen.

Adjusting the focus, zoom, and lens shift

Adjust the focus, zoom, and lens shift if the image projected to the screen or its position is shifted even if the projector and the screen are set up in the correct positions.
f When the following projection lens is used, also refer to “Adjusting the focus balance” (x page 72).
g Zoom Lens (Model No.: ET-D3QW300, ET-D3QS400, ET-D3QT500)
Using the control panel
1) Press the <LENS> button on the control panel.
f Pressing the button changes the adjustment screen in the order of [FOCUS], [ZOOM], and [SHIFT].
2) Select each item and press asqw to adjust it.
Using the remote control
1) Press the lens buttons (<FOCUS>, <ZOOM>, <SHIFT>) on the remote control.
f Pressing the <FOCUS> button: Adjusts the focus (adjustment of the lens focus position). f Pressing the <ZOOM> button: Adjusts the zoom (adjustment of the lens zoom position). f Pressing the <SHIFT> button: Adjusts the lens shift (vertical position and horizontal position of the lens).
2) Select each item and press asqw to adjust it.
CAUTION
During the lens shift operation, do not insert your hand in any opening around the lens.
Your hand may be caught in between, resulting to injury.
ENGLISH - 71
Page 72
Chapter 3 Basic Operations — Projecting
Note
f The adjustment can be performed faster by holding down asqw for approximately six seconds or longer while adjusting the focus, or for
approximately three seconds or longer while adjusting the lens shift.
f It is recommended to perform the focus adjustment after 30 minutes have elapsed with the focus test pattern displayed. For details of the
test pattern, refer to “[TEST PATTERN] menu” (x page 181). To use the active focus optimizer function, set the [PROJECTOR SETUP] menu [LENS] [ACTIVE FOCUS OPTIMIZER] [ACTIVE FOCUS] to [ON], and then adjust the focus. (x page 148)
f Only [FOCUS] is shown in yellow so that the displayed menu item can be recognized by color, even when the projector is not focused and
displayed characters are unreadable. (Factory default)
The displayed color of [FOCUS] differs depending on the setting of the [DISPLAY OPTION] menu [ON-SCREEN DISPLAY] [OSD DESIGN].
f If the power is turned off during the focus adjustment, the zoom adjustment, or the lens shift adjustment, turn on the power again and
execute the [PROJECTOR SETUP] menu [LENS] [LENS CALIBRATION]. f When the main power is switched off during focus adjustment, lens calibration is performed automatically during the next focus adjustment. f If the main power is turned off during the lens shift adjustment, a lens calibration error screen is displayed during the next lens shift
adjustment. Execute the [PROJECTOR SETUP] menu [LENS] [LENS CALIBRATION]. f Request a repair to your dealer if the lens calibration error screen is displayed even though the lens calibration is executed.

Adjusting the focus balance

By changing the projected image size, the focus balance in the center and periphery of the image may be lost.
f When the following projection lens is used, the focus balance in the center and periphery of the projected image
can be adjusted on the projection lens side.
g Zoom Lens (Model No.: ET-D3QW300, ET-D3QS400, ET-D3QT500)
f Illustrations are examples. The structure of the adjustment part of the periphery focus differs depending on the
type of the projection lens.
Periphery focus adjustment ring
Lock screw
1) Loosen the lock screw.
f Turn the lock screw on the side of the projection lens counterclockwise to loosen.
2) Turn the tip of the lens barrel or the periphery focus adjustment ring towards the direction of the arrow by hand and align it with the scale of the projection distance.
f Align the mark on the tip of the lens barrel or the periphery focus adjustment ring with the actual projection
distance between the front end of the projection lens and the screen.
3) Tighten the lock screw.
f The tip of the lens barrel or the periphery focus adjustment ring is xed.
4) Adjust the focus of the center of the image.
f For the steps to adjust the focus, refer to “Adjusting the focus, zoom, and lens shift” (x page 71). f The projected image size may change when the focus balance in the center and periphery of the image is
adjusted. When adjusting the focus balance, check the image size as well.
Note
f When the projector is used for the rst time or when the projection lens is replaced, execute the [PROJECTOR SETUP] menu → [LENS] →
[LENS CALIBRATION].
f The projection distance and scale shown on the projection lens are an approximate guide. This does not correspond to the projection
distance range supported by the projector.
72 - ENGLISH
Page 73
Chapter 3 Basic Operations — Projecting

Executing the lens calibration

When the projector is used for the rst time or when the projection lens is replaced, execute the lens calibration.
Detect the lens adjustment limit value, and perform the calibration in the adjustment range.
1) Press the <MENU> button.
f The [MAIN MENU] screen is displayed.
2) Press as to select [PROJECTOR SETUP].
3) Press the <ENTER> button.
f The [PROJECTOR SETUP] screen is displayed.
4) Press as to select [LENS].
5) Press the <ENTER> button.
f The [LENS] screen is displayed.
6) Press as to select [LENS CALIBRATION].
7) Press the <ENTER> button.
f The [LENS CALIBRATION] screen is displayed.
8) Press as to select an item.
Executes the calibrations for the lens shift, focus, and zoom.
[SHIFT/FOCUS/ZOOM]
[SHIFT/FOCUS]
[ZOOM] Executes the calibration of the zoom adjustment range.
After completing the calibration in the adjustment range, the projection lens will move to the home position.
Executes the calibrations for the lens shift and focus. After completing the calibration in the adjustment range, the projection lens will move to the home position.
9) Press the <ENTER> button.
f The conrmation screen is displayed.
10) Press qw to select [OK], and press the <ENTER> button.
f The lens calibration is started.
Note
f For details of operation, refer to the [PROJECTOR SETUP] menu [LENS] [LENS CALIBRATION] (x page 154). f The origin position of the lens mounter and the home position of the projection lens are automatically updated when the lens shift calibration
is performed. The home position is an origin position of the lens shift (vertical position and horizontal position of the lens) based on the
calibration result. It does not match with the optical image center position.

Moving the projection lens to the home position

Operate in following procedure to move the projection lens to the home position.
When operating from the main menu
1) Press the <MENU> button.
f The [MAIN MENU] screen is displayed.
2) Press as to select [PROJECTOR SETUP].
3) Press the <ENTER> button.
f The [PROJECTOR SETUP] screen is displayed.
4) Press as to select [LENS].
5) Press the <ENTER> button.
f The [LENS] screen is displayed.
6) Press as to select [LENS HOME POSITION].
ENGLISH - 73
Page 74
Chapter 3 Basic Operations — Projecting
7) Press the <ENTER> button.
f The conrmation screen is displayed.
8) Press qw to select [OK], and press the <ENTER> button.
f The projection lens is moved to the home position.
Note
f [PROGRESS] is displayed in the menu while the projection lens is moved to the home position. f The projection lens is not moved to the correct home position when the [PROJECTOR SETUP] menu [LENS] [LENS CALIBRATION]
is not executed.
f The home position does not match with the optical image center position.
When operating from the lens shift adjustment screen
1) Press the <DEFAULT> button on the remote control while displaying the lens shift adjustment screen.
f The conrmation screen is displayed.
2) Press qw to select [OK], and press the <ENTER> button.
f The projection lens is moved to the home position.
Note
f [PROGRESS] is displayed in the menu while the projection lens is moved to the home position. f The projection lens is not moved to the correct home position when the [PROJECTOR SETUP] menu [LENS] [LENS CALIBRATION]
is not executed.
f The [HOME POSITION] screen can also be displayed by pressing the <LENS> button on the control panel or the <SHIFT> button on the
remote control for three seconds or longer.

Lens shift range

The projector can adjust the position of the projected image within the lens shift range for each projection lens
based on the optical center position of the image (standard projection position). Optical center position of the
image is an image position based on the optical axis center of the projector. Perform the lens shift adjustment within the range indicated in the following illustration. Note that moving the lens
outside the adjustment range may change the focus. This is because the shift of the lens is restricted to protect the optical parts.
Following illustration indicates the lens shift range when the projector is installed on desk/oor.
Projection lens Model No. ET-D3QW300 ET-D3QT600
Lens shift range
Projected image width H
0.14 H
Optical axis center
0.14 H
0.4 V
Projected image height V
0.4 V
Projected image width H
0.08 H
Optical axis center
0.08 H
0.25 V
Projected image height V
0.25 V
74 - ENGLISH
Standard projection position
Standard projection position
Page 75
Chapter 3 Basic Operations — Projecting
Projection lens Model No. ET-D3QS400, ET-D3QT500 ET-D3QT700, ET-D3QT800
Lens shift range
Projected image width H
0.16 H
Optical axis center
Standard projection position
0.16 H
0.45 V
Projected image height V
0.45 V
Standard projection position
Projected image width H
0.1 H
Optical axis center
0.1 H
0.3 V
0.3 V

Adjusting the lens mounter when the focus is unbalanced

Focus balance
Relationship between the tilt of the lens and the screen focus surface
When the projection lens is tilted in contrast with the image forming surface, tilting the front side (screen side) of the projection lens downwards (in the direction of the dotted arrow line), the upper side of the screen focus
surface will tilt inwards and the lower side will tilt outwards as shown in the example.
Projection lens
Projected image height V
Image forming surface
Screen focus surface
How to adjust the focus balance (adjustment by tilting the lens mounter)
When the entire screen surface is not uniform even if the focus has been adjusted, the lens mounter has focus adjustment screws in three locations.
f Tool used: Hex driver or Allen wrench (diagonal 4.0 mm (5/32"))
Lens mounter structure
Focus adjustment screws (a), (b), and (c) can be turned to move the lens mount bracket back and forth. Also, tightening the xed screws locks the lens mount bracket in place so it does not move.
When a projection lens with a large weight is installed, or when the projector is installed on an inclination, the lens may tilt and the focus may become unbalanced. In these cases, perform adjustment by referring to the relationship between the adjustment location and adjustment screws.
ENGLISH - 75
Page 76
Chapter 3 Basic Operations — Projecting
r Front view diagram of the lens mounter (viewed from the screen side)
Fixing screws
(b) (c)
Lens mount bracket
(a)
Note
f Focus adjustment screws (a), (b), and (c) are adjusted with the lens attached.
Adjustment procedure
r Relationship between the adjustment location and adjustment screws
(a)
(b) (c)
Adjustment location:
(b)+(c)
Location where the just focus point of the screen is in the inner side of the screen
When the just focus point of
the screen in V up (top in the
vertical direction) is in the inner side of the screen
(a) Rotate counterclockwise ― (b) Rotate counterclockwise Rotate counterclockwise
(c) Rotate counterclockwise Rotate counterclockwise
When the just focus point of the
screen in V bottom (bottom in
the vertical direction) is in the inner side of the screen
When the just focus point of
the screen in H left (left in the
horizontal direction) is in the inner side of the screen
When the just focus point of the
screen in H right (right in the
horizontal direction) is in the inner side of the screen
1) Press the <FOCUS> button on the remote control or the <LENS> button on the control panel to display the focus adjustment screen.
2) Press s to shift the focus of the entire screen once.
3) Press a to stop on any part of the screen to be the first just focus point.
f For the location where focus is shifted in this state, the just focus point is on the inner side of the screen.
4) Loosen the fixed screws in the position relative to the location where the focus is shifted the most (the location where the just focus point is shifted the most towards the inner side in Step 2)) up to one and half rotations.
f Turn screws clockwise in two locations, or at least in one location when making an adjustment.
76 - ENGLISH
Page 77
Chapter 3 Basic Operations — Projecting
5) Slowly turn the focus adjustment screws corresponding to the locations counterclockwise and stop where the image is in focus. (x page 75)
f If the screws are turned counterclockwise, the tilt of the lens will change by moving the lens mount bracket
of the lens mounter forward (screen side), and in the projected image on the screen, the focus point in the
opposite direction of the adjustment screws will move from the inner side of the screen to the outside.
6) Press the <SHIFT> button on the remote control or the <LENS> button on the control panel to display the lens shift adjustment menu, and reset the screen position of the projected image on the screen surface back to an optimal state.
7) Perform focus adjustment again near the center of the screen and if it is still not enough, fine tune the amount of rotation of the adjustment screws.
8) When adjustments have been made, securely tighten the loosened fixing screws.
9) Adjust the focus again using the remote control.
ENGLISH - 77
Page 78
Chapter 3 Basic Operations — Using the USB memory

Using the USB memory

This projector supports the attachment of the USB memory. Attach the USB memory to the <USB> terminal when
using the data cloning function, the rmware update function, etc.
Note
f For the data cloning function, refer to the [PROJECTOR SETUP] menu [DATA CLONING] (x page 178). f For the rmware update function, refer to the [PROJECTOR SETUP] menu [FIRMWARE UPDATE] (x page 180).

Notes on use

Observe following.
f Do not disassemble or modify the USB memory. f Do not apply strong impact on the USB memory. f Do not pour liquid such as water or get it wet. f Do not place foreign object into the terminal section. f Do not touch the metal terminal with hand or metal. f Do not leave the USB memory in a place with high humidity or dust. f Do not leave the USB memory in a place where static electricity or electromagnetic radiation is generated. f Store the USB memory appropriately in a location that small children cannot reach. f Immediately remove the USB memory from the projector when smoke or odor is noticed, and contact the
manufacturer.
f Do not remove the USB memory from the projector while reading or writing the data.

USB memory that can be used with the projector

This projector supports the commercially available USB 2.0 compatible USB memory formatted in FAT16 or FAT32.
f Only the single partition structure is supported.

Attaching the USB memory

1) Insert the USB memory all the way in to the <USB> terminal.
Attention
f Take care of the orientation of the terminal when inserting the USB memory so that it will not get damaged. f Do not use a USB extension cable or a USB hub, and directly insert the USB memory into the <USB> terminal of the projector. f Do not insert the USB memory into the <DC OUT 1>/<DC OUT 2> terminals. The USB memory cannot be used on the <DC OUT 1>/<DC
OUT 2> terminals.
Note
f The USB memory can be attached even when the projector is turned on.

Removing the USB memory

1) Remove the USB memory after confirming that the indicator on the USB memory is not blinking.
Attention
f The blinking of the indicator of the USB memory attached to the projector is indicating that the projector is accessing (reading or writing) the
USB memory. Do not remove the USB memory from the projector when the indicator is blinking.
f The access status to the USB memory cannot be conrmed when a USB memory without the monitoring function such as indicator is used.
In such case, remove the USB memory after conrming one of the following.
g Turn off the projector. g When using the data cloning function, conrm that the saving or loading of the data to/from the USB memory is completed in the menu
screen.
g When using the rmware update function, wait until the projector automatically goes into standby after the update has started.
78 - ENGLISH
Page 79
Chapter 3 Basic Operations — Operating with the remote control

Operating with the remote control

Using the shutter function

If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the image temporarily.
button
1) Press the <SHUTTER> button.
f The image disappears. f This operation can be also performed using the <SHUTTER> button on the control panel.
2) Press the <SHUTTER> button again.
f The image is displayed.
Note
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the shutter function is in use (shutter: closed). f You can set whether to use the mechanical shutter or not and the time for the fade in/fade out of the image using the [DISPLAY OPTION]
menu [SHUTTER SETTING].
f If [MECHANICAL SHUTTER] in the [DISPLAY OPTION] menu [SHUTTER SETTING] (x page 138) is set to [DISABLE], the light source
may be lit dimly due to warm-up when the shutter function is used while the operating environment temperature is around 0 °C (32 °F).

Using the on-screen display function

Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen
display, such as the menu or the input terminal name.
button
1) Press the <ON SCREEN> button.
f Turns off (hides) the on-screen display.
2) Press the <ON SCREEN> button again.
f Cancels the hide condition of the on-screen display.
ENGLISH - 79
Page 80
Chapter 3 Basic Operations — Operating with the remote control
Note
f The hide condition of the on-screen display can also be canceled by pressing the <MENU> button on the control panel for at least three
seconds while the on-screen display is off (hidden).

Using the automatic setup function

The image position and the signal level can be automatically adjusted when HDMI/DisplayPort/DVI-D signal is input.
It is recommended to input an image with bright white borders at the edges and high-contrast black and white characters when executing the automatic setup. Avoid using images that include halftones or gradation, such as photographs and computer graphics.
button
1) Press the <AUTO SETUP> button.
f [COMPLETE] is displayed when it has completed without any problem.
Note
f The items to be automatically adjusted when the automatic setup function is executed can be set in the [DISPLAY OPTION] menu [AUTO
SETUP] (x page 114).
f It is necessary to install the optional Interface Board equipped with the corresponding input on the slot to input the HDMI/DisplayPort/DVI-D
signal directly without passing through the <DIGITAL LINK> terminal.
f If an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or the position adjustment may not be performed
properly even when [COMPLETE] appears. In such a case, adjust the following settings.
g The [POSITION] menu [SHIFT] (x page 98)
f Automatic adjustment may not work depending on the model of the computer. f Images may be disrupted for a few seconds during execution of the automatic setup, but it is not a malfunction. f Adjustment is required for each input signal. f Automatic setup can be canceled by pressing the <MENU> button while the automatic setup is being executed. f Even if a signal possible to perform the automatic setup is being input, it may not be able to adjust correctly if the automatic setup function is
executed while the moving image is being input. [INCOMPLETE] may be displayed, or the adjustment may not be completed correctly even if [COMPLETE] is displayed.

Switching the image aspect ratio

Switch the image aspect ratio according to the input.
button
1) Press the <ASPECT> button.
f The setting will change each time you press the button.
Note
f The aspect ratio of the image can also be switched using the menu operation. Refer to the [POSITION] menu [ASPECT] (x page 98)
for details.

Using the function button

By assigning the following functions to the <FUNCTION> button, it can be used as a simplied shortcut button.
[SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], [WAVEFORM MONITOR], [LENS MEMORY LOAD], [PROJECTION METHOD], [GEOMETRY], [OSD POSITION]
button
1) Press the <FUNCTION> button.
Note
f Assignment of the function is performed from the [PROJECTOR SETUP] menu [FUNCTION BUTTON] (x page 172).
The [FUNCTION BUTTON] screen can also be displayed by holding down the <FUNCTION> button on the remote control.
80 - ENGLISH
Page 81
Chapter 3 Basic Operations — Operating with the remote control

Displaying internal test pattern

The projector has nine types of internal test patterns to check the condition of the projector. To display test patterns, perform the following steps.
button
1) Press the <TEST PATTERN> button.
2) Press qw to select the test pattern.
Note
f Test patterns can also be displayed using the menu operation. Refer to “[TEST PATTERN] menu” (x page 181) for details. f Settings of position, size, and other factors will not be reected in test patterns. Make sure to display the input signal before performing
various adjustments.

Using the status function

Display the status of the projector.
button
1) Press the <STATUS> button.
f The [STATUS] screen is displayed.
STATUS
PROJECTOR TYPE
SERIAL NUMBER
PROJECTOR RUNTIME
LIGHT RUNTIME
CONTINUOUS LIGHTING TIME
MAIN/SUB VERSION
NETWORK VERSION
INTAKE AIR TEMP.
EXHAUST AIR TEMP.
SELF TEST
ENTER
E-MAIL/USB
PT-RQ50K
123456789012
100000h
100000h / 100000h
1h 23m
1.00 / 1.00
31°C/87°F
31°C/87°F
NO ERRORS
MENU
EXITCHANGE
1/6
1.00
Note
f The projector status can also be displayed using the menu operation. Refer to the [PROJECTOR SETUP] menu [STATUS]
(x page 173) for details.

Setting ID number of the remote control

When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector individually using a single remote control, if a unique ID number is assigned to each projector.
After setting the ID number of the projector, set same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID ALL> button on the remote control. Also, you can control a projector by pressing the <ID ALL> button on the remote control even if you do not know the projector ID.
button
1) Press the <ID SET> button on the remote control.
2) Within five seconds, press and set the one-digit or two-digit ID number set on the projector body using the number (<0> - <9>) buttons.
f If you press the <ID ALL> button, you can control the projectors regardless of the ID number setting of the
projector body.
ENGLISH - 81
Page 82
Chapter 3 Basic Operations — Operating with the remote control
Attention
f Since the ID number of the remote control can be set without the projector body, do not press the <ID SET> button on the remote control
carelessly. If the <ID SET> button is pressed and no number (<0> - <9>) buttons are pressed within ve seconds, the ID number returns to
its original value before the <ID SET> button was pressed.
f The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead
batteries. Set the same ID number again when the batteries are replaced.
Note
f When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector
body, as same as when [ALL] is set.
f Set the ID number of the projector body from the [PROJECTOR SETUP] menu [PROJECTOR ID].
82 - ENGLISH
Page 83

Chapter 4 Settings

This chapter describes the settings and adjustments you can make using the on-screen menu.
ENGLISH - 83
Page 84
Chapter 4 Settings — Menu navigation

Menu navigation

The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.

Navigating through the menu

Operating procedure
button
1) Press the <MENU> button on the remote control or control panel.
f The [MAIN MENU] screen is displayed.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
ENTER
SUB MENU
2) Press as to select an item from the main menu.
f The selected item is highlighted in yellow.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
ENTER
SUB MENU
3) Press the <ENTER> button.
f The sub-menu items of the selected main menu are displayed.
POSITION
SHIFT
ASPECT
ZOOM
GEOMETRY
CONVERGENCE
DEFAULT
OFF
OFF
84 - ENGLISH
ENTER
MENU SELECT SUB MENU
Page 85
Chapter 4 Settings — Menu navigation
4) Press as to select a sub-menu, and press qw or the <ENTER> button to change or adjust settings.
f Some items will switch in order as follows each time you press qw.
A B C
f For some items, press qw to display an individual adjustment screen with a bar scale as shown below.
CONTRAST
ADJUST
0
Note
f Pressing the <MENU> button while the menu screen is displayed returns to the previous menu. f Some items or functions may not be adjusted or used depending on the signals input to the projector. When the items cannot be adjusted or
used, the items in the menu screen are shown in black characters, and they cannot be adjusted or set. If the item in the menu screen is displayed in black characters and the item cannot be adjusted or set, the factor causing it is displayed by pressing the <ENTER> button while the corresponding menu is selected.
f Some items can be adjusted even if signals are not input. f Individual adjustment screen is cleared automatically if no operation is performed for approximately ve seconds. f For menu items, refer to “Main menu” (x page 85) and “Sub-menu” (x page 86). f The cursor color depends on the setting in the [DISPLAY OPTION] menu [ON-SCREEN DISPLAY] [OSD DESIGN]. The selected item
is displayed with the yellow cursor by the factory default.
f In the portrait setting, the on-screen menu is displayed sideways.
To display the on-screen menu vertically, change the setting of the [DISPLAY OPTION] menu [ON-SCREEN DISPLAY] [OSD ROTATION].
Resetting adjustment values to the factory default
If the <DEFAULT> button on the remote control is pressed, the values adjusted in the menu items are restored to the factory default settings.
button
1) Press the <DEFAULT> button on the remote control.
CONTRAST
ADJUST
Note
f You cannot reset all the settings to the factory default at a time. f To reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECTOR SETUP] menu
[INITIALIZE].
f Some items cannot be reset to the factory default settings even when the <DEFAULT> button on the remote control is pressed. Adjust those
items individually.
f The triangular mark under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular
mark varies according to the selected input signals.
Current adjustment value
Factory default setting
0

Main menu

The following items are in the main menu. When a main menu item is selected, the screen changes to a sub-menu selection screen. The menu item with l in the [SIMPLE] mode column indicates that this is displayed in the menu screen (OSD)
when the [DISPLAY OPTION] menu [MENU MODE] is set to [SIMPLE].
Main menu item [SIMPLE] mode Page
[PICTURE]
[POSITION]
[ADVANCED MENU] 106
l
l
89
98
ENGLISH - 85
Page 86
Chapter 4 Settings — Menu navigation
Main menu item [SIMPLE] mode Page
[DISPLAY LANGUAGE]
[DISPLAY OPTION]
[PROJECTOR SETUP]
[TEST PATTERN]
[SIGNAL LIST]
l
l
l
l
l
111
112
143
181
182
[SECURITY] 185
[NETWORK]
l
191

Sub-menu

The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu. The menu item with l in the [SIMPLE] mode column indicates that this is displayed in the menu screen (OSD)
when the [DISPLAY OPTION] menu [MENU MODE] is set to [SIMPLE].
[PICTURE]
Sub-menu item Factory default [SIMPLE] mode Page
[PICTURE MODE] [DYNAMIC] [CONTRAST] [0] [BRIGHTNESS] [0] [COLOR] [0] [TINT] [0]
*1
*1
*1
*1
[COLOR TEMPERATURE] [DEFAULT] [GAMMA] [DEFAULT] [SYSTEM DAYLIGHT VIEW] [OFF] [SHARPNESS] [+8] [NOISE REDUCTION] [2] [DYNAMIC CONTRAST] [2]
*1
*1
*1
*1
*1
*1
l l l l
90 90 92 94 94 94 94
[COLOR SPACE] [NATIVE] 96 [SYSTEM SELECTOR] [AUTO]
*2
96
89 89 90 90
*1 Depends on the [PICTURE MODE]. *2 Depends on the signal input.
[POSITION]
Sub-menu item Factory default [SIMPLE] mode Page
[SHIFT] 98 [ASPECT] [DEFAULT]
l
[ZOOM] 99 [GEOMETRY] [OFF]
l
[CONVERGENCE] [OFF] 105
[ADVANCED MENU]
Sub-menu item Factory default [SIMPLE] mode Page
[DIGITAL CINEMA REALITY] [AUTO]
*1
106 [BLANKING] 106 [EDGE BLENDING] [OFF] 107
86 - ENGLISH
98
100
Page 87
Chapter 4 Settings — Menu navigation
Sub-menu item Factory default [SIMPLE] mode Page
[FRAME RESPONSE] [NORMAL] 109 [FRAME DELAY] [+0.00ms] 109 [RASTER POSITION] 110
*1 Depends on the signal input.
[DISPLAY LANGUAGE]
Details (x page 111)
[DISPLAY OPTION]
Sub-menu item Factory default [SIMPLE] mode Page
[COLOR MATCHING] [OFF] [SCREEN SETTING] [AUTO SIGNAL] [OFF] 114 [AUTO SETUP] 114 [BACKUP INPUT SETTING] 115 [SIMUL INPUT SETTING] 117 [SLOT IN] 11 7 [DIGITAL LINK IN] 131 [ON-SCREEN DISPLAY] [MENU MODE] [NORMAL] [BACK COLOR] [BLUE] 136 [STARTUP LOGO] [DEFAULT LOGO] [UNIFORMITY] 137 [SHUTTER SETTING] 138 [FREEZE] 140 [WAVEFORM MONITOR] [OFF] 140 [CUT OFF] 141
l l
l l
l
112 114
133 135
136
[PROJECTOR SETUP]
Sub-menu item Factory default [SIMPLE] mode Page
[PROJECTOR ID] [ALL] [PROJECTION METHOD] [LENS] [OPERATION SETTING] [LIGHT OUTPUT] [100.0%] [BRIGHTNESS CONTROL] 158 [NO SIGNAL SETTING] 161 [INITIAL STARTUP] [LAST MEMORY] 165 [STARTUP INPUT SELECT] [LAST USED] 165 [DATE AND TIME] [SCHEDULE] [OFF] 167 [MULTI PROJECTOR SYNC] 168 [RS-232C] [REMOTE2 MODE] [DEFAULT] 172 [FUNCTION BUTTON] 172 [STATUS] [INFO MONITOR SETTING] 176 [DATA CLONING] 178 [SAVE ALL USER DATA] 178 [LOAD ALL USER DATA] 178 [INITIALIZE]
l l l l l
l
l
l
l
143 143 144 154 157
166
170
173
178
ENGLISH - 87
Page 88
Chapter 4 Settings — Menu navigation
Sub-menu item Factory default [SIMPLE] mode Page
[FIRMWARE UPDATE] 180 [SERVICE PASSWORD]
l
[TEST PATTERN]
Details (x page 181)
[SIGNAL LIST]
Details (x page 182)
[SECURITY]
Sub-menu item Factory default [SIMPLE] mode Page
[SECURITY PASSWORD] [OFF] 185 [SECURITY PASSWORD CHANGE] 185 [CONTROL DEVICE SETUP] 185 [CONTROL DEVICE PASSWORD CHANGE] 189
180
[NETWORK]
Sub-menu item Factory default [SIMPLE] mode Page
[DIGITAL LINK MODE] [AUTO] 191 [DIGITAL LINK STATUS] [WIRED LAN] [WIRELESS LAN] [PROJECTOR NAME] [NETWORK CONTROL] [NETWORK STATUS] [DIGITAL LINK MENU] 194 [Art-Net SETUP] [OFF] 195 [Art-Net CHANNEL SETTING] [2] 195 [Art-Net STATUS] 196
*1 [WIRELESS LAN] cannot be set if the optional Wireless Module (Model No.: AJ-WM50 Series) is not attached to the <USB> terminal.
*1
[ENABLE]
l l l l l l
Note
f Some items may not be adjusted or used for certain signal formats to be input to the projector.
When the items cannot be adjusted or used, the items in the menu screen are shown in black characters, and they cannot be adjusted or set.
f Sub-menu items and factory default settings vary depending on the selected input terminal.
191 192 192 193 193 194
88 - ENGLISH
Page 89
Chapter 4 Settings — [PICTURE] menu

[PICTURE] menu

On the menu screen, select [PICTURE] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 84) for the operation of the menu screen.

[PICTURE MODE]

You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [PICTURE MODE].
2) Press qw. f The [PICTURE MODE] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[STANDARD] The image becomes suitable for moving images in general.
[CINEMA] The image becomes suitable for movie contents.
[NATURAL] The image is sRGB compliant.
[DICOM SIM.] The image becomes similar to that of DICOM Part 14 Grayscale Standard.
[DYNAMIC]
[GRAPHIC] The image becomes suitable for input from the personal computer.
[USER] Set any desired picture mode.
The light output is maximized for use in bright areas.
(Factory default setting)
Note
f DICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices. Although the
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
f Press the <ENTER> button when each [PICTURE MODE] is selected to save as a specied value when a new signal is input. The data of
all items except [SYSTEM SELECTOR] in the [PICTURE] menu is saved.
f In the factory default settings, [USER] is set to images that comply with the ITU-R BT.709 standard.
Changing the [USER] name
1) Press as to select [PICTURE MODE].
2) Press qw to select [USER].
3) Press the <ENTER> button. f The [PICTURE MODE] detailed screen is displayed.
4) Press as to select [PICTURE MODE NAME CHANGE], and press the <ENTER> button. f The [PICTURE MODE NAME CHANGE] screen is displayed.
5) Press asqw to select the text, and press the <ENTER> button to enter the text.
6) Press asqw to select [OK], and press the <ENTER> button.
f The picture mode name is changed.

[CONTRAST]

You can adjust the contrast of the colors.
1) Press as to select [CONTRAST].
2) Press qw or the <ENTER> button. f The [CONTRAST] individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation Adjustment Range of adjustment
Press w. Press q.
The screen becomes brighter. The screen becomes darker.
-
31 - +31
ENGLISH - 89
Page 90
Chapter 4 Settings — [PICTURE] menu
Attention
f Adjust [BRIGHTNESS] rst when you need to adjust the black level.

[BRIGHTNESS]

You can adjust the dark (black) part of the projected image.
1) Press as to select [BRIGHTNESS].
2) Press qw or the <ENTER> button. f The [BRIGHTNESS] individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation Adjustment Range of adjustment
Press w. Press q.
Increases the brightness of the dark (black) parts of the screen. Reduces the brightness of the dark (black) parts of the screen.

[COLOR]

You can adjust the color saturation of the projected image.
1) Press as to select [COLOR].
-
31 - +31
2) Press qw or the <ENTER> button. f The [COLOR] individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation Adjustment Range of adjustment
Press w. Press q.
Deepens colors. Weakens colors.

[TINT]

You can adjust the skin tone in the projected image.
1) Press as to select [TINT].
2) Press qw or the <ENTER> button. f The [TINT] individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation Adjustment Range of adjustment
Press w. Press q.
Adjusts skin tone toward greenish color. Adjusts skin tone toward reddish purple.

[COLOR TEMPERATURE]

-
31 - +31
-
31 - +31
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
Adjusting with color temperature
1) Press as to select [COLOR TEMPERATURE].
2) Press qw. f The [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[DEFAULT] Factory default setting.
90 - ENGLISH
Page 91
Chapter 4 Settings — [PICTURE] menu
[USER1] [USER2]
[3200K] - [13000K] Allows you to set in increments of 100 K. Select so that images become natural.
Adjusts white balance as desired. Refer to “Adjusting desired white balance” (x page 91) for details.
Note
f When [PICTURE MODE] (x page 89) is set to [USER] or [DICOM SIM.], [DEFAULT] cannot be selected. f When the [DISPLAY OPTION] menu [COLOR MATCHING] is set to anything other than [OFF], [COLOR TEMPERATURE] is xed to
[USER1].
f The color temperature numerical values are guidelines.
Adjusting desired white balance
1) Press as to select [COLOR TEMPERATURE].
2) Press qw. f The [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press qw to select [USER1] or [USER2].
4) Press the <ENTER> button. f The [COLOR TEMPERATURE] screen is displayed.
5) Press as to select [WHITE BALANCE].
6) Press the <ENTER> button. f The [WHITE BALANCE] screen is displayed.
7) Press as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].
8) Press the <ENTER> button. f The [WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.
9) Press as to select [RED], [GREEN], or [BLUE].
10) Press qw to adjust the level.
Item Operation Adjustment Range of adjustment
[RED]
[GREEN]
[BLUE]
Press w. Press q. Press w. Press q. Press w. Press q.
Deepens red. Weakens red. Deepens green. Weakens green. Deepens blue. Weakens blue.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is
+255)
-
[WHITE BALANCE LOW]:
127 - +127 (factory default is
0)
Note
f Adjust [COLOR TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment
does not look suitable, you can press the <DEFAULT> button on the remote control to return the setting for the selected item only to the factory default setting.
Adjusting desired white balance based on existing color temperature settings
1) Press as to select [COLOR TEMPERATURE].
2) Press qw. f The [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press qw to select anything other than [USER1] and [USER2].
4) Press the <ENTER> button. f The [CHANGE TO *****] screen is displayed.
5) Press as to select [USER1] or [USER2].
f The status of the color temperature changed is saved to the selected item.
ENGLISH - 91
Page 92
Chapter 4 Settings — [PICTURE] menu
6) Press the <ENTER> button.
f The conrmation screen is displayed.
7) Press qw to select [OK], and press the <ENTER> button.
f The [USER1] or [USER2] data is overwritten. f If you press qw to select [CANCEL] and then press the <ENTER> button, the data will not be overwritten. f The [WHITE BALANCE HIGH] screen is displayed.
8) Press as to select [RED], [GREEN], or [BLUE].
9) Press qw to adjust the level.
Note
f Adjust [COLOR TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment
does not look suitable, you can press the <DEFAULT> button on the remote control to return the setting for the selected item only to the factory default setting.
f When color temperature has been changed, the colors before and after the change will differ slightly.
Changing the name of [USER1] or [USER2]
1) Press as to select [COLOR TEMPERATURE].
2) Press qw. f The [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press qw to select [USER1] or [USER2].
4) Press the <ENTER> button. f The [COLOR TEMPERATURE] screen is displayed.
5) Press as to select [COLOR TEMPERATURE NAME CHANGE].
6) Press the <ENTER> button. f The [COLOR TEMPERATURE NAME CHANGE] screen is displayed.
7) Press asqw to select the text, and press the <ENTER> button to enter the text.
8) Press asqw to select [OK], and press the <ENTER> button.
f The name set to color temperature is changed.
Note
f When a name is changed, display of [USER1], [USER2] is also changed.

[GAMMA]

You can switch gamma mode.
1) Press as to select [GAMMA].
2) Press qw or the <ENTER> button. f The [GAMMA] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[DEFAULT]
[USER1] [USER2]
[HDR ST2084-500]
[HDR ST2084-1000]
[HDR HLG]
[DICOM SIM.] The picture becomes similar to that of DICOM standard.
*1
Gamma mode unique to this projector.
Uses the gamma data registered by the user.
(Registration requires separate software. Consult your dealer.)
Gamma mode compliant with SMPTE ST 2084 that assumes a highest luminance of 500 cd/m
supports HDR (High Dynamic Range).
Gamma mode compliant with SMPTE ST 2084 that assumes a highest luminance of 1 000 cd/m
supports HDR (High Dynamic Range). Gamma mode compliant with ITU-R BT.2100 (HLG: Hybrid Log Gamma system) that supports
HDR (High Dynamic Range).
92 - ENGLISH
2
and
2
and
Page 93
Chapter 4 Settings — [PICTURE] menu
[1.0]
Set so that images become as you like. [2.0] - [2.8] can be set in increments of 0.1.[1.8]
[2.0] - [2.8]
*1 When [PICTURE MODE] is set to [DYNAMIC], [USER], or [DICOM SIM.], [DEFAULT] cannot be selected.
Note
f DICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices. Although the
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
f In the following cases, the gamma mode is automatically set based on the InfoFrame information while displaying the image with the
InfoFrame information added, so the gamma mode cannot be selected. If the information necessary for supporting HDR (High Dynamic
Range) is not included in the InfoFrame information added to the displayed video signal, it will follow the [GAMMA] setting.
g When the [DISPLAY OPTION] menu [DIGITAL LINK IN] [AUTO GAMMA SELECT] is set to [ENABLE], and the DIGITAL LINK input
is selected
g When [AUTO GAMMA SELECT] under the [DISPLAY OPTION] menu [SLOT IN] (HDMI input) is set to [ENABLE], and the HDMI input
corresponding to that setting is selected
g When the [DISPLAY OPTION] menu [SLOT IN] (DisplayPort input) [AUTO GAMMA SELECT] is set to [ENABLE], and the
DisplayPort input applicable to that setting is selected
Setting [HDR HLG SYSTEM GAMMA]
Set the system gamma to be applied to the [USER1], [USER2], and [HDR HLG] gamma modes. This system
gamma is dened by the ITU-R BT.2100 standard.
1) Press as to select [GAMMA].
2) Press qw or the <ENTER> button. f The [GAMMA] individual adjustment screen is displayed.
3) Press qw to select [USER1], [USER2], or [HDR HLG], and press the <ENTER> button.
f The [GAMMA] screen is displayed. f When [HDR HLG] is selected, proceed to Step 5).
4) Press as to select [HDR HLG SYSTEM GAMMA].
5) Press qw to switch the item.
f The items will switch each time you press the button. f [1.00] - [1.62] can be set in increments of 0.01.
Changing the name of [USER1] or [USER2]
1) Press as to select [GAMMA].
2) Press qw or the <ENTER> button. f The [GAMMA] individual adjustment screen is displayed.
3) Press qw to select [USER1] or [USER2].
4) Press the <ENTER> button. f The [GAMMA] screen is displayed.
5) Press as to select [GAMMA NAME CHANGE].
6) Press the <ENTER> button. f The [GAMMA NAME CHANGE] screen is displayed.
7) Press asqw to select the text, and press the <ENTER> button to enter the text.
8) Press asqw to select [OK], and press the <ENTER> button.
f The selected gamma name is changed.
Note
f When a name is changed, display of [USER1], [USER2] is also changed.
ENGLISH - 93
Page 94
Chapter 4 Settings — [PICTURE] menu

[SYSTEM DAYLIGHT VIEW]

You can correct the image to the optimal vividness even if it is projected under a bright light.
1) Press as to select [SYSTEM DAYLIGHT VIEW].
2) Press qw or the <ENTER> button. f The [SYSTEM DAYLIGHT VIEW] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF] No correction.
[1] - [6] Corrects the vividness of the image. The larger the value, the stronger the correction.

[SHARPNESS]

You can adjust the sharpness of the projected image.
1) Press as to select [SHARPNESS].
2) Press qw or the <ENTER> button. f The [SHARPNESS] individual adjustment screen is displayed.
3) Press qw to adjust the level.
Operation Adjustment Range of adjustment
Press w. Press q.
Contours become sharper. Contours become softer.
0 - +15
Note
f If you press w while the adjustment value is [+15], the value will become [0]. If you press q while the adjustment value is [0], the value will
become [+15].

[NOISE REDUCTION]

You can reduce noises when the input image is degraded and noise is occurring in the image signal.
1) Press as to select [NOISE REDUCTION].
2) Press qw or the <ENTER> button. f The [NOISE REDUCTION] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF] No correction.
[1] - [6] Compensates the noise. The larger the value, the stronger the compensation of the noise.
Attention
f When this is set for an input signal with less noise, the image may look different from what it originally was. In such a case, set it to [OFF].

[DYNAMIC CONTRAST]

Light adjustment of the light source and signal compensation are performed automatically according to the image to make the contrast optimum for the image.
1) Press as to select [DYNAMIC CONTRAST].
2) Press qw or the <ENTER> button. f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
94 - ENGLISH
Page 95
Chapter 4 Settings — [PICTURE] menu
[OFF] Disables the dynamic contrast function.
[1] Adjusts the light source and compensates signals to a small extent. [2] Adjusts the light source and compensates signals to a moderate extent. [3] Adjusts the light source and compensates signals to a large extent.
[USER]
Set any desired correction. Refer to “Performing desired correction” (x page 95) for details.
Performing desired correction
1) Press as to select [DYNAMIC CONTRAST].
2) Press qw or the <ENTER> button. f The [DYNAMIC CONTRAST] individual adjustment screen is displayed.
3) Press qw to select [USER].
4) Press the <ENTER> button. f The [DYNAMIC CONTRAST] screen is displayed.
5) Press as to select the item to set.
f The items of the detailed settings will switch each time you press qw. f Press the <ENTER> button when [MULTI PROJECTOR SYNC] is selected.
Setting item Details
[AUTO CONTRAST]
(Automatic light source
adjustment)
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness level
of the signal to start the light
adjustment)
[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[LIGHTS OUT FADE-IN]
(Setting of fade-in when lighting
up again)
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[MANUAL INTENSITY]
(Manual light source
adjustment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[OFF] Does not adjust the light source.
The higher the value, the stronger the light adjustment of the light
[1] - [255]
[6%] - [50%]
[DISABLE] Does not turn off the light source.
[0.0s] - [10.0s]
[0%] - [5%]
[OFF]
[0.5s] - [10.0s]
[OFF]
[0.5s] - [10.0s]
[0] - [255]
[OFF] Does not compensate the signal.
[1] Slightly compensates the signal. [2] Moderately compensates the signal. [3] Strongly compensates the signal.
source. Can be set in increments of 1.
Adjusts the light source when the brightness level of the video signal being input gets lower than the set value. The higher the value, the larger the range to perform the light adjustment of the light source.
Can be set in increments of 1 %. (Factory setting: 30 %)
Turns off the light source when the brightness level of the video signal being input goes under the value set in [LIGHTS OUT SIGNAL LEVEL]. Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] ­[4.0s] can be selected in increments of 0.5.
Set the level of the brightness of the video signal to turn off the light source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
Does not set the fade-in of the image when the light source is turned on again from the condition that the light source was turned off with [LIGHTS OUT TIMER].
Sets the time to fade in the image when the light source is turned on again from the condition that the light source was turned off with [LIGHTS OUT TIMER]. Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] ­[4.0s] can be selected in increments of 0.5.
Does not set the fade-out of the image when the light source is turned off with [LIGHTS OUT TIMER].
Sets the time to fade out the image when the light source is turned off with [LIGHTS OUT TIMER]. Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] ­[4.0s] can be selected in increments of 0.5.
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
ENGLISH - 95
Page 96
Chapter 4 Settings — [PICTURE] menu
Setting item Details
Sets the contrast synchronization function. This setting item is common with the following menu item.
[MULTI PROJECTOR SYNC]
f The [PROJECTOR SETUP] menu [MULTI PROJECTOR
SYNC]
Refer to the [PROJECTOR SETUP] menu [MULTI PROJECTOR SYNC] (x page 168) for details.
Note
f [LIGHTS OUT SIGNAL LEVEL], [LIGHTS OUT FADE-IN], and [LIGHTS OUT FADE-OUT] cannot be set when [LIGHTS OUT TIMER] is set
to [DISABLE].
f When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again
from the state that the light source has turned off by this function.
g When the brightness level of the video signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL] g When the input signal is gone g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f The contrast will be maximized when [DYNAMIC GAMMA] is set to [3]. f The contrast synchronization function is a function to display a combined screen with a balanced contrast by sharing the brightness level of
the video signal input to each projector when a multi-display is constructed by combining the projected image of multiple projectors.

[COLOR SPACE]

Set the color space used for the color representation of the image.
1) Press as to select [COLOR SPACE].
2) Press qw or the <ENTER> button. f The [COLOR SPACE] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[NATIVE] Displays the image with a color space unique to this projector. [ITU-709] Displays the image with a color space compliant with the ITU-R BT.709 standard.
[DCI-P3 emu.] Displays the image with a color space close to DCI-P3.
[ITU-2020 emu.] Displays the image with a color space close to the ITU-R BT.2020 standard.
Note
f DCI-P3 is the specications of the digital cinema color region dened by the Digital Cinema Initiatives (DCI). f In the following cases, the color space is automatically set based on the InfoFrame information while displaying the image with the
InfoFrame information added, so the [COLOR SPACE] cannot be set. If the information necessary for supporting HDR (High Dynamic
Range) is not included in the InfoFrame information added to the displayed video signal, it will follow the [COLOR SPACE] setting.
g When the [DISPLAY OPTION] menu [DIGITAL LINK IN] [AUTO COLOR SPACE SELECT] is set to [ENABLE], and the DIGITAL
LINK input is selected
g When [AUTO COLOR SPACE SELECT] under the [DISPLAY OPTION] menu [SLOT IN] (HDMI input) is set to [ENABLE], and the
HDMI input corresponding to that setting is selected
g When the [DISPLAY OPTION] menu [SLOT IN] (DisplayPort input) [AUTO COLOR SPACE SELECT] is set to [ENABLE], and the
DisplayPort input applicable to that setting is selected

[SYSTEM SELECTOR]

The projector will automatically detect the input signal, but you can set the system method manually when an unstable signal is input. Set the system method matching the input signal.
1) Press as to select [SYSTEM SELECTOR].
2) Press the <ENTER> button.
3) Press as to select a system format.
f Available system formats vary depending on the input signal.
Terminal System format
<DIGITAL LINK> terminal,
<HDMI IN 1> terminal, <HDMI
IN 2> terminal, <HDMI IN
3> terminal, <HDMI IN 4>
terminal
480/60p or 576/50p signal Select [AUTO], [RGB], or [YC
Other moving image signals Select [AUTO], [RGB], or [YP
BCR
BPR
].
].
96 - ENGLISH
Page 97
Chapter 4 Settings — [PICTURE] menu
Terminal System format
<DVI-D IN 1> terminal, <DVI-D
IN 2> terminal, <DVI-D IN 3> terminal, <DVI-D IN 4>
terminal
<DisplayPort IN 1> terminal, <DisplayPort IN 2> terminal, <DisplayPort IN 3> terminal,
<DisplayPort IN 4> terminal
480/60p or 576/50p signal Select [RGB] or [YC
Other moving image signals Select [RGB] or [YP
Moving image signals Select [AUTO], [RGB], or [YP
BCR
BPR
].
].
].
BPR
4) Press the <ENTER> button.
Note
f For details of the types of video signals that can be used with the projector, refer to “List of compatible signals” (x page 274). f This may not function properly for some connected external devices. f The selection item for the input signal to the <HDMI IN 1> terminal and the <HDMI IN 2> terminal can be selected when the optional
Interface Board equipped with the HDMI input is installed in <SLOT 1>.
f The selection item for the input signal to the <HDMI IN 3> terminal and the <HDMI IN 4> terminal can be selected when the optional
Interface Board equipped with the HDMI input is installed in <SLOT 2>.
f The selection item for the input signal to the <DVI-D IN 1> terminal and the <DVI-D IN 2> terminal can be selected when the optional
Interface Board equipped with the DVI-D input is installed in <SLOT 1>.
f The selection item for the input signal to the <DVI-D IN 3> terminal and the <DVI-D IN 4> terminal can be selected when the optional
Interface Board equipped with the DVI-D input is installed in <SLOT 2>.
f The selection item for the input signal to the <DisplayPort IN 1> terminal and the <DisplayPort IN 2> terminal can be selected when the
optional Interface Board equipped with the DisplayPort input is installed in <SLOT 1>.
f The selection item for the input signal to the <DisplayPort IN 3> terminal and the <DisplayPort IN 4> terminal can be selected when the
optional Interface Board equipped with the DisplayPort input is installed in <SLOT 2>.
f For the SDI input, the signal format can be set in detail in the [DISPLAY OPTION] menu [SLOT IN].

sRGB-compliant video

sRGB is an international standard (IEC61966-2-1) for color reproduction dened by IEC (International
Electrotechnical Commission). Set according to the following steps to reproduce more faithful, sRGB compliant colors.
1) Set [COLOR MATCHING] to [OFF].
f Refer to [COLOR MATCHING] (x page 112).
2) Display the [PICTURE] menu.
f Refer to “[PICTURE] menu” (x page 89).
3) Press as to select [PICTURE MODE].
4) Press qw to set [NATURAL].
5) Press as to select [COLOR].
6) Press the <DEFAULT> button on the remote control to set the factory default setting.
7) Follow Steps 5) to 6) to set [TINT], [COLOR TEMPERATURE], [GAMMA], and [SYSTEM DAYLIGHT
VIEW] to the factory default settings.
Note
f sRGB is available for RGB signal input only.
ENGLISH - 97
Page 98
Chapter 4 Settings — [POSITION] menu

[POSITION] menu

On the menu screen, select [POSITION] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 84) for the operation of the menu screen.
Note
f When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK>
terminal, adjust the shift and aspect from the menu of DIGITAL LINK output supported device rst.

[SHIFT]

Move the image position vertically or horizontally if the image projected on the screen is still out of position even when the positions of the projector and screen are correct.
1) Press as to select [SHIFT].
2) Press the <ENTER> button. f The [SHIFT] screen is displayed.
3) Press asqw to adjust the position.
Orientation Operation Adjustment
Press a.
Vertical (up and down)
adjustment
Press s.
Press w.
Horizontal (right and left)
adjustment
Press q.
The image position moves up.
The image position moves down.
The image position moves to the right.
The image position moves to the left.
Note
f For the portrait setting, image position is moved horizontally when “Vertical (up and down) adjustment” is made. Image position is moved
vertically when “Horizontal (right and left) adjustment” is made.

[ASPECT]

You can switch the aspect ratio of the image. The aspect ratio is switched within the screen range selected in the [DISPLAY OPTION] menu [SCREEN
SETTING] [SCREEN FORMAT]. Set [SCREEN FORMAT] rst. (x page 114)
1) Press as to select [ASPECT].
2) Press qw or the <ENTER> button. f The [ASPECT] individual adjustment screen is displayed.
3) Press qw to switch the item.
f The items will switch each time you press the button.
[DEFAULT] Displays images without changing the aspect ratio of the input signals.
[THROUGH] Displays images without changing the resolution of the input signals.
98 - ENGLISH
Page 99
Chapter 4 Settings — [POSITION] menu
[16:9]
[4:3]
[H FIT]
[V FIT]
[HV FIT]
*1 Standard signals are input signals with an aspect ratio of 4:3 or 5:4. *2 Wide-screen signals are input signals with an aspect ratio of 17:9, 16:10, 16:9, 15:10, or 15:9.
Displays images with the aspect ratio converted to 16:9 when standard signals are input wide-screen signals are input*2, the images are displayed without changing the aspect ratio.
Displays images without changing the aspect ratio when standard signals are input screen signals are input*2, and [4:3] is selected in [SCREEN FORMAT], the image is displayed by converting the aspect ratio to 4:3. When anything other than [4:3] is selected in [SCREEN FORMAT],
the images are reduced to be displayed without changing input aspect ratio so that the images will t
in the 4:3 screen. Displays images using the entire width of the screen range selected in [SCREEN FORMAT]. When
signals have the aspect ratio vertically longer than the screen aspect ratio selected in [SCREEN FORMAT], the images are displayed with the top and bottom parts cut off.
Displays images using the entire height of the screen range selected in [SCREEN FORMAT]. When signals have the aspect ratio horizontally longer than the aspect ratio of the screen selected in [SCREEN FORMAT], the images are displayed with the right and left parts cut off.
Displays images in the entire screen range selected in [SCREEN FORMAT]. When the aspect ratio of the input signals differs from that of the screen range, the images are displayed with the aspect ratio converted to that of the screen selected in [SCREEN FORMAT].
*1
. When
*1
. When wide-
Note
f If an aspect ratio which is different from the aspect ratio for the input signals is selected, the images will appear differently from the originals.
Be careful of this when selecting the aspect ratio.
f If using the projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that
adjusting the aspect ratio or using the zoom function to change the screen images may be an infringement of the rights of the original copyright owner for that program under copyright protection laws. Take care when using a function of the projector such as the aspect ratio adjustment and zoom function.
f If conventional (normal) 4:3 images which are not wide-screen images are displayed on a wide screen, the edges of the images may not
be visible or they may become distorted. Such images should be viewed as with an aspect ratio of 4:3 in the original format intended by the creator of the images.

[ZOOM]

You can adjust the image size. The adjustments in [ZOOM] will differ depending on the setting of the [POSITION] menu [ASPECT].
When [ASPECT] is set to other than [DEFAULT] and [THROUGH]
1) Press as to select [ZOOM].
2) Press the <ENTER> button. f The [ZOOM] screen is displayed.
3) Press as to select [INTERLOCKED].
4) Press qw to switch the item.
[OFF] Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.
[ON]
5) Press as to select [VERTICAL] or [HORIZONTAL].
f If [ON] is selected, select [BOTH].
6) Press qw to adjust.
Note
Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the
same magnication.
f When [ASPECT] is set to [THROUGH], [ZOOM] cannot be adjusted.
When [ASPECT] is set to [DEFAULT]
1) Press as to select [ZOOM].
2) Press the <ENTER> button. f The [ZOOM] screen is displayed.
3) Press as to select [MODE].
ENGLISH - 99
Page 100
Chapter 4 Settings — [POSITION] menu
4) Press qw to switch the item.
[INTERNAL] Enlarges the size within the aspect range set with [SCREEN FORMAT].
[FULL] Enlarges or reduces the size using the entire display area set with [SCREEN FORMAT].
5) Press as to select [INTERLOCKED].
6) Press qw to switch the item.
[OFF] Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.
[ON]
Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the
same magnication.
7) Press as to select [VERTICAL] or [HORIZONTAL].
f If [ON] is selected, select [BOTH].
8) Press qw to adjust.
Note
f When [ASPECT] is not set to [DEFAULT], [MODE] is not displayed. f Zoom ratio less than 100 cannot be set when the video signal fullling one of the following conditions is being input.
g Video signal with resolution exceeding 1 920 x 1 200 dots g Video signal with dot clock frequency exceeding 150 MHz

[GEOMETRY]

You can correct various types of distortion in a projected image. Unique image processing technology enables projection of a square image on a special screen shape. The projected image can be made to look more natural by making topical correction as necessary.
1) Press as to select [GEOMETRY].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF] Does not perform geometric adjustment.
[KEYSTONE] Adjusts any trapezoidal distortion in the projected image.
[CORNER/PINCUSHION] Adjusts any distortion in the four corners of the projected image.
[CURVED CORRECTION] Adjusts any curved distortion in the projected image.
[PC-1] [PC-2] [PC-3]
*1 “Geometric & Setup Management Software” can be downloaded from the Panasonic website (https://panasonic.net/cns/projector/pass/). It is
necessary to register and login to PASS to download.
Note
f The menu, logo, or waveform monitor display may run off the screen when [GEOMETRY] is set. f If [EDGE BLENDING] (x page 107) adjustment and [GEOMETRY] are used together, correct edge blending adjustment may not be
possible in certain environments.
f The image may disappear for a moment or may be disrupted while performing adjustment, but it is not a malfunction.
Select this item when performing correction using a computer and “Geometric & Setup Management
Software”
*1
. Up to three correction data can be saved.
Setting [KEYSTONE] or [CURVED CORRECTION]
1) Press as to select [GEOMETRY].
2) Press qw to select [KEYSTONE] or [CURVED CORRECTION].
3) Press the <ENTER> button. f The [GEOMETRY:KEYSTONE] or [GEOMETRY:CURVED CORRECTION] screen is displayed.
4) Press as to select the item to adjust.
5) Press qw to adjust.
100 - ENGLISH
Loading...