Before operating this product, please read the instructions carefully, and save this manual
for future use.
Before using your projector, be sure to read “ Precautions with regard to safety” (pages 5 to 9).
For network operation, please read the Network Operation Manual.
M0510YZ2011 -CH
TQBJ0322-2
ENGLISH
Essential information
2 ENGLISH
Essential information
Important Safety Notice
Dear Panasonic Customer:
The following information should be read and understood as it provides details, which will enable you to operate
the projector in a manner which is both safe to you and your environment, and conforms to legal requirements
regarding the use of projectors. Keep this booklet with your Panasonic LCD projector for future reference. The
serial number of your product may be found on its bottom. Write it in the space provided below and retain this
booklet in case service is required.
Model number: PT-LB3U/PT-LB2U/PT-LB1U
Serial number:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current
only.
CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power
supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to
obtain a separate 250 V power cord. If you use the accessory cord in such situations, re may result.
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
CAUTION: This equipment is equipped with a three-pin grounding-type power plug.
Do not remove the grounding pin on the power plug. This plug will only t
a grounding-type power outlet. This is a safety feature. If you are unable
to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
NOTICE:
This product has a High Intensity Discharge (HID) lamp that contains mercury. Dispose may be regulated in your
community due to environmental considerations. For disposal or recycling information, please contact your local
authorities, or the Electronic Industries Alliance: http://www.eiae.org
Do not remove
Essential information
ENGLISH 3
Important Safety Notice (continued)
WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•
Consult the dealer or an experienced radio/TV technician for help.•
FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only
shielded interface cables when connecting to computer and/or peripheral devices.
AnychangesormodicationsnotexpresslyapprovedbyPanasonicCorp.ofNorthAmerica
could void the user’s authority to operate this device.
For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the •
building installation wiring.
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily •
accessible.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Information on Disposal in other Countries outside the European
Index ............................................................ 55
Removal of spacer at rear adjuster...........56
Informations essentielles
Avis important concernant la sécurité ..... 57
Précautions concernant la sécurité .........59
Remplacement de l’unite de la lampe.......63
Longer lamp life
The lamp replacement cycle is longer than the former model. (
Approx. 3 000 hours (PT-LB90NTU)
Approx. 5 000 hours (PT-LB3U/PT-LB2U/PT-LB1U)
Standby power reduction
The standby power has been immensely reduced compared to the
previous model.
Approx. 0.9 W (PT-LB90NTU)
Approx. 0.4 W (PT-LB3U/PT-LB2U/PT-LB1U)
(Standby mode: In “ECO”)
User logo display function
You can project your company’s logo when projection starts. ( page 34)
page 45)
Essential information
ENGLISH 5
Precautions with regard to safety
WARNING
POWER
The wall outlet or the circuit breaker shall be
installed near the equipment and shall be easily
accessible when problems occur. If the followings
problems occur, cut off the power supply
immediately.
Continued use of the projector in these conditions will
result in re or electric shock.
If foreign objects or water get inside the projector, cut •
off the power supply.
If the projector is dropped or the cabinet is broken, cut
•
off the power supply.
If you notice smoke, strange smells or noise coming
•
from the projector, cut off the power supply.
Please contact an Authorized Service Center for
repairs, and do not attempt to repair the projector
yourself.
During a thunderstorm, do not touch the projector
or the cable.
Electric shocks can result.
Do not do anything that might damage the power
cord or the power plug.
If the power cord is used while damaged, electric
shocks, short-circuits or re will result.
Do not damage the power cord, make any
•
modications to it, place it near any hot objects, bend
it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any
repairs to the power cord that might be necessary.
Insert the power plug securely into the wall outlet.
If the plug is not inserted correctly, electric shocks or
overheating will result.
Do not use anything other than the provided power
•
cord.
Do not use the provided power cord for other
•
electrical equipment.
Do not use plugs which are damaged or wall outlets
•
which are coming loose from the wall.
Clean the power plug regularly to prevent it from
becoming covered in dust.
Failure to observe this will cause a re.
If dust builds up on the power plug, the resulting
•
humidity can damage the insulation.
If not using the projector for an extended period of
•
time, pull the power plug out from the wall outlet.
Pull the power plug out from the wall outlet and wipe it
with a dry cloth regularly.
Do not handle the power plug with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too
many adapters), overheating may occur and re will
result.
ON USE/INSTALLATION
Do not place liquid containers on top of the
projector.
If water spills onto the projector or gets inside it, re or
electric shocks will result.
If any water gets inside the projector, contact an
Authorized Service Center.
Do not place the projector on soft materials such as
carpets or sponge mats.
Doing so will cause the projector to overheat, which
can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places
or in places where the projector may come into
contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result
in re, electric shocks or components deterioration.
Components deterioration (such as ceiling mount
brackets) may cause the projector which is mounted on
the ceiling to fall down.
Do not install this projector in a place which is
not strong enough to take the full weight of the
projector or on top of a surface which is sloped or
unstable.
Failure to observe this will cause projector to fall down
or tip over the projector, and severe injury or damage
could result.
Do not place another projector or other heavy
objects on top of the projector.
Failure to observe this will cause the projector to
become unbalanced and fall, which could result in
damage or injury. The projector will be damaged or
deformed.
Installation work (such as ceiling suspension)
should only be carried out by a qualied technician.
If installation is not carried out and secured correctly it
can cause injury or accidents, such as electric shocks.
Do not use anything other than an Authorized ceiling
•
mount bracket.
Do not cover the air inlet port or the air outlet port.
Doing so will cause the projector to overheat, which can
cause re or damage to the projector.
Do not place the projector in narrow, badly ventilated
•
places such as closets or bookshelves.
Do not place the projector on cloth or papers, as
•
these materials could be drawn into the air inlet port.
Do not place your hands or other objects close to
the air outlet port.
Doing so will cause burns or damage your hands or
other objects.
Heated air comes out of the air outlet port. Do not
•
place your hands or face, or objects which cannot
withstand heat close to this port.
Essential information
6 ENGLISH
Precautions with regard to safety (continued)
Do not look and place your skin into the lights
emitted from the lens while the projector is being
used.
Doing so can cause burns or loss of sight.
Strong light is emitted from the projector’s lens. Do •
not look or place your hands directly into this light.
Be especially careful not to let young children look
•
into the lens. In addition, turn off the power and
disconnect the power plug when you are away from
the projector.
Do not insert any foreign objects into the projector.
Doing so will cause re or electric shocks.
Do not insert any metal objects or ammable objects
•
into the projector or drop them onto the projector.
Never attempt to remodel or disassemble the
projector.
High voltages can cause re or electric shocks.
For any inspection, adjustment and repair work, please
contact an Authorized Service Center.
Do not project an image with the supplied lens
cover attached.
Doing so can cause re.
ACCESSORIES
Do not use or handle the batteries improperly, and
refer to the following.
Failure to observe this will cause burns, batteries to
leak, overheat, explode or catch re.
Do not use unspecied batteries.•
Use manganese batteries but not rechargeable •
batteries.
Do not dissemble dry cell batteries.
•
Do not heat the batteries or place them into water or •
re.
Do not allow the + and – terminals of the batteries
•
to come into contact with metallic objects such as
necklaces or hairpins.
Do not store batteries together with metallic objects.
•
Store the batteries in a plastic bag and keep them •
away from metallic objects.
Make sure the polarities (+ and
•
inserting the batteries.
Do not use a new battery together with an old battery
•
or mix different types of batteries.
Do not use batteries with the outer cover peeling
•
away or removed.
Remove the empty batteries from the remote control
•
at once.
Insulate the battery using tape or something similar
•
before disposal.
-
) are correct when
If the battery uid leaks, do not touch it with
bare hands, and take the following measures if
necessary.
Battery uid on your skin or clothing could result in •
skin inammation or injury.
Rinse with clean water and seek medical advice
immediately.
Battery uid coming in contact with your eyes could
•
result in loss of sight.
In this case, do not rub your eyes. Rinse with clean
water and seek medical advice immediately.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly
handled, an explosion and severe injury or accidents
will result.
Replacement of the lamp should be carried out by a
•
qualied technician.
The lamp can easily explode if struck against hard
•
objects or dropped.
Before replacing the lamp, be sure to disconnect the
•
power plug from the wall outlet.
Electric shocks or explosions can result if this is not
done.
When replacing the lamp, allow it to cool for at least
•
one hour before handling it otherwise it can cause
burns.
Do not allow infants or pets to touch the remote
control unit.
Keep the remote control unit out of the reach of
•
infants and pets after using it.
CAUTION
POWER
When disconnecting the power cord, be sure to
hold the power plug and power connector.
If the power cord itself is pulled, the lead will become
damaged, and re, short-circuits or serious electric
shocks will result.
When not using the projector for an extended
period of time, disconnect the power plug from
the wall outlet and remove the batteries from the
remote control.
Disconnect the power plug from the wall outlet
before carrying out any cleaning.
Electric shocks can result if this is not done.
Do not allow children to reach the AAA/R03 battery.
The battery can cause personal injury if swallowed.
•
If swallowed, seek medical advice immediately.•
Essential information
ENGLISH 7
Precautions with regard to safety (continued)
ON USE/INSTALLATION
Do not put your weight on this projector.
You could fall or the projector could break, and injury
will result.
Be especially careful not to let young children stand or •
sit on the projector.
Do not place the projector in extremely hot
locations.
Doing so will cause the outer casing or internal
components to deteriorate, or result in re.
Take particular care in locations exposed to direct
•
sunlight or near stoves.
Always disconnect all cables before moving the
projector.
Moving the projector with cables still attached can
damage the cables, which will cause re or electric
shocks to occur.
ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room
immediately. Do not touch or bring your face close
to the broken pieces.
Failure to observe this will cause the user to absorb
the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as
uorescent lamps, and the broken pieces will cause
injury.
If you believe that you have absorbed the gas or that
the gas has got into your eyes or mouth, seek medical
advice immediately.
Ask your dealer about replacing the lamp unit and
check the inside of the projector.
CAUTIONS WHEN TRANSPORTING
CAUTIONS WHEN INSTALLING
DO NOT USE UNDER THE FOLLOWING
CONDITIONS.
Do not set up the projector outdoors.•
The projector is designed for indoor use only.
•
Avoid setting up in places which are subject to
vibration or shocks.
If the projector is installed in a place where vibrations
are transmitted or mounted in a car or a vessel,
vibrations or impacts will result in damage to the
internal parts, causing failure. Install the product in a
place free from vibrations and impacts.
•
Avoid setting up in places which are subject to
sudden temperature changes, such as near an air
conditioner or lighting equipment.
Failure to observe this will result in malfunctions or
the lamp life will be shortened.
See “TEMP INDICATOR” on page 43.
Avoid setting up in places which are near high-
•
voltage power lines or near motors.
The product will be exposed to interference if it is
installed in the vicinity of high-voltage electrical power
lines or power sources.
• Do not install the projector at elevations higher
than 2 700 m (8 858 ft) above sea level.
If using this projector at high elevations 1 400 -
2 700 m (4 593 - 8 858 ft) above sea level, set the
HIGH ALTITUDE MODE to ON.
If using this projector at elevations lower than 1 400 m
(4 593 ft) above sea level, set the HIGH ALTITUDE MODE to OFF.
Failure to observe this will result in malfunctions
or the lamp life or life of other components will be
shortened.
When transporting the projector, the leg adjusters must
be housed and do not hold them.
When transporting, keep the projector in the
provided carrying bag with the lens cover on it.
Face the lens of the projector in an upward direction
•
and put it gently into the carrying bag.
Do not put anything other than the projector and its
•
accessories in the carrying bag.
BE SURE TO ASK A SPECIALIZED
TECHNICIAN WHEN INSTALLING THE
PRODUCT TO A CEILING.
If the product is to be installed hanging from the ceiling,
purchase an optional hanging attachment (Model No.
ET-PKB2). Please call a specialized technician or
contact an Authorized Service Center for installation.
LENS FOCUS
Do not adjust the lens focus in the initial period after
switching the projector on. The high clarity projector
lens is thermally affected by the light from the light
source, making the focus unstable in the period just
after switching on. Please allow a warm-up time of at
least 30 minutes before adjusting the lens focus.
Essential information
8 ENGLISH
Precautions with regard to safety (continued)
CAUTIONS ON USE
IN ORDER TO GET THE PICTURE QUALITY
Draw curtains or blinds over windows and turn off any
lights near the screen to prevent outside light or light
from indoor lamps from shining onto the screen.
Depending on where the projector is used, air exhaust
vents or the warm air from air conditioning can cause a
shimmering effect on the screen. For this reason, take
care not to shield the air exhaust vents and consider the
direction of the air owing from air conditioning.
DO NOT TOUCH THE SURFACE OF THE
PROJECTOR LENS WITH YOUR BARE HAND.
If the surface of the lens becomes dirty from ngerprints
or anything else, this will be magnied and projected
onto the screen. Please put the standard lens cover on
the projector when you do not use it.
DO NOT MOVE THE PROJECTOR WHILE
IT IS OPERATING OR SUBJECT IT TO
VIBRATION OR IMPACT.
The service life of its internal components will be
shortened.
THE PROJECTOR HAS A HIGH
PRESSURE MERCURY LAMP THAT IS
CHARACTERIZED AS FOLLOWS:
OPTICAL COMPONENTS
It may be necessary to replace the optical components
such as Liquid crystal panels and Polarizing plates
in less than 1 year if using the projector in a high
temperature environment or in a very dusty, oily smoke
or tobacco smoke environment. For more details,
please contact your dealer.
LIQUID CRYSTAL PANEL
The Liquid crystal panels are precision-made. Note that
in rare cases, pixels of high precision could be missing
or always lit, but this is not a malfunction.
Do not project the same image for long periods of
time, as this may remain as an afterimage on the liquid
crystal panel. Display the white screen test pattern for
more than an hour to remove it. See “TEST PATTERN”
on page 39.
SECURITY
TAKE SAFETY MEASURES AGAINST
FOLLOWING INCIDENTS.
Personal information being leaked via this product.•
Unauthorized operation of this product by a malicious •
third party.
Interfering or stopping of this product by a malicious
•
third party.
SECURITY INSTRUCTION
The brightness of the lamp will decrease over time.•
The lamp may explode or shorten the lamp life by •
shocks or chipping damage.
In rare cases, it may burst shortly after the rst use.
•
The possibility of its bursting increases when the lamp •
is used beyond the replacement time.
If the lamp bursts, gas inside the lamp is released in
•
the form of smoke.
The life of a mercury lamp varies according to the
•
individual difference or conditions of use.
In particular, turning the power on and off frequently
•
and/or repeatedly as well as continuous use for
10 hours will greatly affect the life cycle. Provide a
lamp for replacement in advance.
CONNECTION TO EXTERNAL DEVICE
When connecting the projector to a computer or
external device, use the power cord supplied with the
corresponding device and a commercially available
shielded interface cable.
The connecting network must be secured by rewall •
or others.
Change your password regularly.
•
Do not use a password that is simple to guess.•
Panasonic and its afliate companies would never •
directly inquire about your password.
Do not share your password with the general public.
•
Set a password, and place restrictions on the users •
who can log in.
Essential information
ENGLISH 9
Precautions with regard to safety (continued)
AUTO
SETUP
MENU
RETURN
ENTER
FREEZE
AV
MUTE
COMPUTER
VIDEO
DEFAULT
FUNCTION
WIN.
INDEX-
DIGITAL ZOOM
VOLUME
CLEANING AND MAINTENANCE
ASK AN AUTHORIZED SERVICE
CENTER TO CLEAN THE INSIDE OF THE
DISPOSAL
When discarding this product, please contact your local
authorities or dealer and ask for the correct method of
disposal.
PROJECTOR AT LEAST ONCE A YEAR.
If dust is left to build up inside the projector without
being cleaned out, it can result in re or problems
with operation. It is a good idea to clean the inside of
the projector before the season when humid weather
arrives.
Ask your nearest Authorized Service Center to clean the
projector when required.
Please discuss with the Authorized Service Center
regarding cleaning costs.
SUPPLIED ACCESSORIES
Make sure that the following accessories are provided with your projector.
Remote control (×1)
(N2QAYA000011)
Power cord (×1)
(K2CG3YY00072)
RGB signal cable (×1) 1.8 m (5' 10")
(K1HY15YY0009)
Carrying bag (×1)
(TPEP033)
Power cord secure lock (×1)
(TTRA0185)
Lens cover (×1) (TKKL5499)
(Attached to the projector by
AAA/R03 batteries for Remote
control (×2)
CD-ROM (×1)
(TXFQB02VKN5)
default.)
NOTE:
The protectors for the enclosed products, such as a plug cover or foam cartons, must be handled appropriately.•
Contact an Authorized Service Center for any lost accessories.•
Keep the accessories away from children.•
The model Nos. of the accessories and parts sold separately are subject to change without notice.•
NOTE:
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Preparation
10 ENGLISH
PLEASE SELECT LANGUAGE.
SELECT
ENTER
INITIAL SETTING
ENTER
RETURN
SELECT
ENTER
INSTALLATION
INITIAL SETTING
FRONT/DESK
HIGH ALTITUDE MODE
SWITCH TO HIGH ALTITUDE MODE “ON” IF OVER 1400m(4593Ft).
OFF
ENTER
Preparation
Start-up display
The LANGUAGE and INITIAL SETTING menu will be displayed when the projector is turned on for the rst time or
after it has been initialized. ( page 39)
Navigate the DISPLAY OPTION menu to set the menus in accordance to its application and environment settings.
NOTE:
When the projector is turned on for the rst time, you may be required to adjust the “zoom ring” and “focus ring” • ( page 11)
on the top of the projector body to make the menu screen clearer.
For details, see POSITION THE IMAGE. (
page 22)
LANGUAGE
1
2
To select the desired language.
To proceed to INITIAL SETTING
menu.
INITIAL SETTING
1
2
INSTALLATION ( page 15, 37)
FRONT/
DESK
FRONT/
CEILING
REAR/
DESK
REAR/
CEILING
To select the desired menu.
INSTALLATION
HIGH ALTITUDE MODE
To change the settings in the
menu.
Put it on a desk or oor and project
from the front
Mount it on the ceiling with a ceiling
mount bracket (sold separately) and
project from the front
Put it on a desk or oor and project
from the rear (a translucent screen is
required)
Mount it on the ceiling with a ceiling
mount bracket (sold separately) and
project from the rear (a translucent
screen is required)
Zoom ring – To adjust the size of projection.
( page 22)
⑦
Focus ring – To adjust the focus. ( page 22)
⑧
Air intake port
⑥
Navigate through the menus.
Conrm selection.
⑦
Create shortcut assigned to certain selected
function. ( page 25, 38)
⑧
Switch the input connections.
( page 22)
⑨
Switch between standby mode and projection
mode. ( page 20)
Preparation
12 ENGLISH
Details of your projector (continued)
①
③
⑩
⑨
④
⑥⑤
⑦
②
⑧
LAN
SERIAL
COMPUTER 1 IN
S-VIDEO
IN
VIDEO IN
AUDIO IN
12
AUDIO
OUT
COMPUTER 2 IN
①②③④
⑤
⑥
⑦
Rear and bottom view
①
Terminals
②
Remote control signal receptor
③
AC IN
Connect the power cord to supply electric power to
the projector. ( page 18)
④
Air intake port
⑤
Front leg adjuster
To adjust the projection angle.( page 22)
NOTE:
Do not connect any power cable other than the attached one.•
Do not cover the ventilation openings of the air intake port or air outlet port. •
Terminals
⑥
Rear leg adjuster
To adjust the projection angle. ( page 22)
⑦
Burglar hook port
Attach a commercial burglar prevention cable.
⑧
Air outlet port
Hot air comes out from this opening.
⑨
Speaker
⑩
Lamp unit compartment ( page 46)
①
Connect to a network cable.
(See “Network Operation Manual”.)
②
Connect to a computer to control the projector’s
operation.
( page 17, 51)
③
Connect to a computer or YP
( page 17)
④
Connect to an S-VIDEO signal cable.
( page 16)
NOTE:
Do not place your hands or other objects close to the air outlet port as this may cause damage or injury.•
Do not place your hands or face, or objects which cannot withstand heat near the air outlet port. Hot air comes out •
from this port.
signal cable.
BPR
⑤
Connect to a VIDEO signal cable.
( page 16)
⑥
Connect audio cables for inputting audio signal.
( page 17)
⑦
Connect an audio cable for audio signal output
to the connected equipment. If it is connected to
this terminal, no sound comes out of the built-in
speaker.
( page 16, 17)
Preparation
ENGLISH 13
Details of your projector (continued)
AUTO
SETUP
MENU
RETURN
ENTER
FREEZE
AV
MUTE
COMPUTER
VIDEO
DEFAULT
FUNCTION
WIN.
INDEX-
DIGITAL ZOOM
VOLUME
①
⑤
②
③
④
⑥
⑦
⑫
⑪
⑩
⑧
⑨
PROJECTOR’S REMOTE CONTROL
Top and rear view
Installing/removing batteries
Press the tab and lift up the
cover.
Remote control
signal emitters
Use only manganese batteries.
Insert the batteries according to the
polarity diagram indicated inside or
remove.
Front view
①
POWER
Switch between standby mode and projection
mode. ( page 20, 21)
②
Display the Main menu. ( page 27)
③
Navigate through the menus with [
conrm the selection with [ENTER]. ( page 26)
④
Capture the projected image as a frozen picture.
( page 23)
⑤
Switch the required input signal button to select.
( page 23)
⑥
Reset some of the settings to the factory default
settings. ( page 24)
⑦
Control the zoom size. ( page 25)
⑧
Control speaker volume. ( page 24)
⑨
Create shortcut assigned to certain selected
function. ( page 25, 38)
⑩
Display frozen image while the display of
subsequent images continues. ( page 24)
⑪
Turn off the projection temporarily. ( page 23)
⑫
Detect the input signal.
Adjust the settings of SHIFT, DOT CLOCK
and CLOCK PHASE in the POSITION menu
automatically for COMPUTER signals. ( page 23)
] and
NOTE:
Do not drop the remote control.•
Avoid contact with liquids or moisture.•
Do not attempt to modify or disassemble the remote control.•
Do not let strong light shine onto the signal receptor which will cause a malfunction. •
The remote control operates within the range of 7 m (23' 0"), approximately ±30 ° vertically and horizontally from the projector •
avoiding any obstacles.
•
The operating range may differ due to the screen material and may not be effective with a translucent screen.
Getting started
14 ENGLISH
SD
SW
SH
L (LW/LT)
SH
79.2 mm
L (LW/LT)
SW
Projected image
Screen
Screen
+30 °
-
30 °
Getting started
Set up your projector
SCREEN SIZE AND THROW DISTANCE
You can adjust the projection size with 1.2× zoom lens. Calculate and dene the throw distance as follows.
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection
size
Screen
diagonal
(SD)
0.84 m (33")——1.1 m (3' 7")1.1 m (3' 7")——1.2 m (3' 11")1.3 m (4' 3")
1.02 m (40")1.1 m (3' 7")1.2 m (3' 11")1.4 m (4' 7")1.4 m (4' 7")1.3 m (4' 3")1.3 m (4' 3")1.5 m (4' 11")1.5 m (4' 11")
1.27 m (50")1.4 m (4' 7")1.5 m (4' 11") 1.7 m (5' 6")1.8 m (5' 9")1.6 m (5' 3")1.6 m (5' 3")1.9 m (6' 2")1.9 m (6' 2")
1.52 m (60")1.7 m (5' 6")1.8 m (5' 9")2.1 m (6' 10")2.1 m (6' 10")1.9 m (6' 2")1.9 m (6' 2")2.3 m (7' 6")2.3 m (7' 6")
1.78 m (70")2.0 m (6' 6")2.1 m (6' 10")2.4 m (7' 10")2.5 m (8' 2")2.2 m (7' 2")2.3 m (7' 6")2.6 m (8' 6")2.7 m (8' 9")
2.03 m (80")2.3 m (7' 6")2.4 m (7' 10")2.8 m (9' 2")2.8 m (9' 2")2.5 m (8' 2")2.6 m (8' 6")3.0 m (9' 10")3.1 m (10' 2")
2.29 m (90")2.6 m (8' 6")2.7 m (8' 9")3.1 m (10' 2")3.2 m (10' 6")2.9 m (9' 6")2.9 m (9' 6")3.4 m (11' 1")3.5 m (11' 5")
2.54 m (100")2.9 m (9' 6")3.0 m (9' 10")3.5 m (11' 5")3.5 m (11' 5") 3.2 m (10' 6") 3.3 m (10' 8") 3.8 m (12' 5")3.9 m (12' 8")
3.05 m (120") 3.5 m (11' 5") 3.6 m (11' 8") 4.2 m (13' 9")4.3 m (14' 1") 3.8 m (12' 5") 3.9 m (12' 8") 4.6 m (15' 1")4.7 m (15' 4")
3.81 m (150") 4.4 m (14' 4") 4.5 m (14' 8") 5.2 m (17' 0")5.3 m (17' 4") 4.8 m (15' 7") 4.9 m (16' 1") 5.7 m (18' 8")5.8 m (19' 0")
5.08 m (200") 5.8 m (19' 0") 6.0 m (19' 7") 7.0 m (22' 11") 7.1 m (23' 3") 6.3 m (20' 8")6.6 m (21' 7") 7.6 m (24' 11") 7.8 m (25' 6")
6.35 m (250") 7.3 m (23' 11") 7.5 m (24' 6")8.7 m (28' 6") 8.9 m (29' 2") 7.9 m (25' 11")
7.62 m (300") 8.7 m (28' 6") 9.0 m (29' 5") 10.5 m (34' 5") 10.7 m (35' 1") 9.5 m (31' 2") 9.9 m (32' 5") 11.5 m (37' 7") 11.7 m (38' 4")
Minimum distance
(LW)
PT-LB3/
PT-LB2
For 4:3 aspect ratioFor 16:9 aspect ratio
Maximum distance
PT-LB1PT-LB3/
PT-LB2
(LT)
PT-LB1PT-LB3/
Minimum distance
(LW)
PT-LB1PT-LB3/
PT-LB2
8.2 m (26' 9") 9.5 m (31' 2") 9.7 m (31' 8")
Maximum distance
PT-LB2
You can calculate detailed screen dimensions from the “Screen diagonal”. The unit of all the calculation results is
m. (The results below differ slightly from the actual measurements.)
If the projection size is SD,
(LT)
PT-LB1
For 4:3 aspect ratioFor 16:9 aspect ratio
"
Screen height (SH)= SD (
Screen width (SW)= SD (
PT-LB3/PT-LB2 = 0.0292 × SD (
) × 0.0152= SD (") × 0.0125
"
) × 0.0203= SD (") × 0.0221
") -
0.025= 0.0318 × SD (") - 0.011
Minimum distance (LW)
") -
PT-LB1= 0.0302 × SD (
PT-LB3/PT-LB2 = 0.0351 × SD (
0.035= 0.0330 × SD (") - 0.041
") -
0.033= 0.0383 × SD (") - 0.035
Maximum distance (LT)
") -
PT-LB1= 0.0358 × SD (
0.035= 0.0391 × SD (") - 0.040
NOTE:
For best projection image quality, install a screen where sunlight or room lightings do not •
shine directly onto the screen. Close window shades or curtains to block the light and turn
off the lightings.
•
Do not use the projector at a raised or horizontally tilted position. It may cause the
projector to malfunction.
However, you can tilt the projector’s body approximately ±30 ° vertically and ±10 °
horizontally.
Over tilting may result in shortening the component’s life.
•
Do not cover the air outlet port and air intake ports or place anything within 50 cm (20") near them as this may cause damage
or injury.
Getting started
ENGLISH 15
Set up your projector (continued)
PROJECTION METHOD
See “INSTALLATION” on page 37 to select the projection method.
Put it on a desk or oor and project from the frontMount it on the ceiling and project from the front
MenuMethod
INSTALLATIONFRONT/DESK
Put it on a desk or oor and project from the rear
(Use translucent screen)
MenuMethod
INSTALLATIONREAR/DESK
NOTE:
Use the optional ceiling mount bracket (ET-PKB2) when mounting the projector on the ceiling.•
You can adjust the projection angle in the vertical direction by adjusting the leg adjuster button. • ( page 22)
Mount it on the ceiling and project from the rear
(Use translucent screen)
MenuMethod
INSTALLATIONFRONT/CEILING
MenuMethod
INSTALLATIONREAR/CEILING
Getting started
16 ENGLISH
Connections
LAN
S
ERIAL
CO
MPUTER 1 IN
S-VIDEO
V
IDEO INAUDIO IN
AUDI
O
OUT
COMPUTER 2 IN
S-VIDEO
IN
VIDEO IN
AUDIO IN
12
AUDIO
OUT
Preparations
Read and follow the operating instructions of each peripheral device and turn the peripheral devices off prior to •
making any connections.
Prepare the selected peripheral devices with the connection cables that correspond to the projector’s terminals.•
All peripheral devices and cables used for the connections are sold separately unless indicated otherwise.•
If the input signal is affected by signal jitter, the projected image may have poor image quality and timebase •
correction is effective.
Conrmthetypesofvideosignals,•see “LIST OF COMPATIBLE SIGNALS”. ( page 50)
Example: AV equipment
Audio system
To audio input
NOTE:
Switch the audio connection manually for more than one AV equipment connections.•
To video output or
audio output
or
To S-VIDEO
output
DVD player
Video player
Getting started
ENGLISH 17
Connections (continued)
S
ERIA
L
COMPU
TER 1 IN
S-VIDEO
IN
VIDEO INAUDIO IN
2
AUDI
O
OUT
CO
MPUTER 2 IN
LAN
SERIAL
COMPUTER 1 IN
AUDIO IN
1
AUDIO
OUT
COMPUTER 2 IN
Example: Computers
Computer
(Controlling a projector)
Computer
Audio system
NOTE:
When connecting the RGB signal cable, tighten the xing screws on the D-Sub (15-pin) connector.•
For the network connection between the projector and computers, see “Network Operation Manual” in the CD-ROM provided.•
Only the RGB signal cable (1 piece) is attached. If any other cables are necessary, purchase them from the market.•
(Controlling a projector)
ComputerComputer
Basic operations
18 ENGLISH
Basic operations
Turn the projector ON or OFF
POWER CORD
Fix the provided “power cord secure lock” to the power cord on the projector to prevent the cord from
coming off.
For details, see “Precautions with regard to safety”. ( pages 5 to 9)
Install the “power cord secure lock”Detach the “power cord secure lock”
Push the connector all the way into the AC
1
IN terminal ensuring that the shape of the
connector matches that of the terminal.
Align the side of the “power cord secure lock”
2
with the side of the “Rail guide” of the AC IN
terminal and slide it in.
Latch to the latch catcher and press until it
3
clicks.
Latch
Rail guide
Unplug the power plug from the wall outlet.
1
Depress the latch and slide off the lock.
2
Latch
Slide up the “power cord secure lock” and
3
remove it.
Rail guide
Hold the connector rmly and detach it from the
4
AC IN terminal.
Direct power on function
If the power cord is connected to a wall outlet with
INITIAL START UP (PROJECTOR SETUP menu)
is set to ON, projection will start even when the
control panel is disabled. ( page 37)
Connect the power plug to a wall outlet.
4
Direct power off function
You can switch off the electric power supply any
time by unplugging the power plug from the wall
outlet or by switching off the main power.
The internal cooling fan keeps operating using
the internal power supply and automatically stops
when cooled.
NOTE:
Do not put the projector into the carrying bag with the •
POWER indicator lit.
Basic operations
ENGLISH 19
Turn the projector ON or OFF (continued)
STANDBY
(R)
ON(G)
LAMP
ENTER
INPUT
SELECT
POWER INDICATOR
POWER indicator
POWER indicator status
Indicator statusStatus
No illumination or ashingNo power is supplied and the internal cooling fan is not operating.
LitThe power is turned off (when STANDBY MODE is set to ECO).
If [POWER] button is pressed, projection starts.
Red
Green
Orange
FlashingThe power is turned off (when STANDBY MODE is set to
NORMAL).
If [POWER] button is pressed, projection starts.
FlashingThe power is on and preparing for projection.
LitThe projector is projecting.
LitNo power supply and the power is preparing for being turned off.
It is turned off (The projection is set in STANDBY MODE) after a
while.
FlashingThe power is switched on again while cooling the lamp and
recovering to the projection mode. Recovery may take a while.
POWER indicator
shows status of the projector’s power
When the TEMP indicator ashes, the
POWER indicator lights red and you
cannot turn the projector on.
NOTE:
When the power is turned off, the internal fan cools the lamp using internal power supply.•
The power is turned on again while cooling the lamp and recovers to the projection mode. Recovery may take a while.•
While the power is turned off (when • STANDBY MODE is set to ECO, the POWER indicator is lit red), power of about 0.4 W is
consumed.
Basic operations
20 ENGLISH
Turn the projector ON or OFF (continued)
S
T
ANDBY
(R
)
ON(G
)
AUTO
SETUP
M
ENU
RETURN
ENTER
FREEZ
E
MUT
2
)
TURN THE PROJECTOR ON
POWER indicator
Before switching on the projector, make sure all the other devices are correctly connected and remove the Lens
cover. ( page 16)
Connect the power cord. ( page 18)
1
After a while the “power indicator” lights or
ashes in red.
Press the POWER button.
2
POWER• indicator ashes green several times
before it lights up and the STARTUP LOGO is
displayed. See STARTUP LOGO in DISPLAY
OPTION menu. ( page 34)
NOTE:
Conrm that • CONTROL PANEL (when operating with
the projector body) or REMOTE CONTROLLER (when
operating with the remote control) under CONTROL DEVICE SETUP in the SECURITY menu is set to ENABLE.
(
page 42)
When setting the SECURITY menu, you will be asked to
input the password. (
•
When starting up the projector, some small rattling or
tinkling sound may be heard. These are normal and will not
affect the performance of the projector.
•
When the internal cooling fan is operating, some operational
sound may be heard. The loudness of the operational
sound depends on the external temperature.
• INITIAL START UP (PROJECTOR SETUP menu) is set
If
to ON, the projector starts projecting when the power cord is
connected to a wall outlet. (
•
If the projector is turned on again while the internal cooling
fan is still operating by the internal power supply, the display
may icker due to the specications of the lamp. These are
normal and will not affect the performance of the projector.
page 40)
page 37)
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.