Page 1
ENGLISH
R
Before operating this product, please read the instructions carefully and save this
manual for future use.
LCD Projector
Operating Instructions
Model No. PT-LB10NTE
PT-LB10E
PT-LB10VE
PT-LB10SE
TQBJ 0142
Commercial Use
POWER
INPUT
VIDEO
RGB
AUTO
MENU
SETUP
ENTER
SHUTTER
FREEZE
STD
VOLUME D.ZOOM
INDEX
WINDOW
PROJECTOR
Page 2
2-ENGLISH
IMPORTANT SAFETY NOTICE
WARNING:
To prevent damage which may result in fire or shock
hazard, do not expose this appliance to rain or moisture.
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The
sound pressure level at the operator position is equal or less than 70 dB
(A) according to ISO 7779.
WARNING:
1) Remove the plug from the wall outlet when this unit is not in use for a
prolonged period of time.
2) To prevent electric shock, do not remove cover. No user serviceable
parts inside. Refer servicing to qualified service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is
equipped with a three prong earthing-type power plug. This plug will
only fit an earthing-type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact an electrician. Do not
defeat the purpose of the earthing plug.
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should
note it in the space provided below and retain this booklet in case service is
required.
Model number: PT-LB10NTE / PT-LB10E / PT-LB10VE / PT-LB10SE
Serial number:
WARNING: THIS APPARATUS MUST BE EARTHED.
Page 3
ENGLISH-3
Preparation
WARNING:
B For permanently connected equipment, a readily accessible disconnect
device shall be incorporated in the building installation wiring;
B For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
CAUTION:
To assure continued compliance, follow the attached installation
instructions, which includes using the provided power cord and shielded
interface cables when connecting to computer or peripheral device.
If you use serial port to connect PC for external control of projector, you
must use optional RS-232C serial interface cable with ferrite core. Any
unauthorized changes or modifications to this equipment will void the
user’s authority to operate.
Page 4
4-ENGLISH
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse
need to be replaced, please ensure that the replacement fuse has a rating of
13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted
when the fuse is replaced. If you lose the fuse cover, the plug must not be
used until a replacement cover is obtained. A replacement fuse cover can be
purchased from an Authorised Service Centre.
If the fitted moulded plug is unsuitable for the mains socket in your
home, then the fuse should be removed and the plug cut off and
disposed of safely. There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: — THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: — The wires in this mains lead are coloured in accordance
with the following code: —
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected
to the terminal in the plug which is marked with the letter E or by the
Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in
the plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal
in the plug which is marked with the letter L or coloured RED.
How to replace the fuse
Open the fuse
compartment with a screwdriver and replace the
fuse.
ASA
13A250V
BS1363/A
HE-8
N
ASA
L
FUSE
Page 5
ENGLISH-5
Preparation
Contents
Preparation
IMPORTANT SAFETY NOTICE ...2
Precautions with regard to
safety .........................................6
Accessories ...............................10
Before use ..................................11
Location and function of each
part...........................................13
Inserting the wireless card .......18
Getting started
Setting-up...................................19
Projection methods, Projector
position, Projection distances
Connections...............................21
Connecting to computer,
Connecting to video equipment
Preparation for the remote
control unit..............................23
Basic operation
Turning on the power................24
Turning off the power................26
Useful functions
Correcting keystone distortion
and automatic positioning.....28
Turning off the picture and sound
momentarily ............................29
Pausing a picture.......................29
Enlarging the picture.................30
Adjusting the volume ................30
Displaying two screens.............31
Adjustments and settings
On-screen menus ......................32
Menu screens, Menu operation
guide, Returning a setting to the
factory default
Correcting keystone
distortion .................................36
Adjusting the picture.................37
PICTURE MODE, CONTRAST,
BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP.,
White balance R/G/B, AI,
TV-SYSTEM, STILL MODE,
SIGNAL MODE, Projecting sRGBcompatible pictures
Adjusting the position...............40
POSITION, DOT CLOCK, CLOCK
PHASE, ASPECT, RESIZING,
FRAME LOCK
Changing the display
language..................................43
Option settings ..........................43
OSD, AUTO SEARCH, AUTO
SIGNAL, AUTO KEYSTN,
RGB/YPBP
R, VGA60/480p, SXGA
MODE, Noise Reduction (NR),
BLACKBOARD, BACK COLOR,
FRONT/REAR, DESK/CEILING, FAN
CONTROL, LAMP POWER, LAMP
RUNTIME, FUNC 1, CONTROL KEY,
AUTO POW.OFF, POWER
MEMORY
Setting up the security
function ...................................47
INPUT/AMEND PASSWD,
TEXT DISPLAY/CHANGE
Network setup............................49
Care and maintenance
When the TEMP indicator and the
LAMP indicator are
illuminated...............................50
Cleaning and replacing
the air filter ..............................52
Replacing the lamp unit ............53
Before calling for service..........56
Cleaning and maintenance .......57
Others
Specifications ............................58
Appendix ....................................60
List of compatible signals, Pin
assignments, Projection dimensions
calculation methods, Using the
SERIAL connector
Dimensions ................................64
Trademark
acknowledgements ................64
Page 6
6-ENGLISH
Precautions with regard to safety
WARNING
If you notice smoke, strange smells or noise coming from the
projector, disconnect the mains plug from the mains socket.
B Do not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
B Check that no more smoke is coming out, and then contact an Authorised
Service Centre for repairs.
B Do not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
B If the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
B If installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, disconnect the mains plug from the
mains socket.
B Continued use of the projector in this condition may result in fire or electric
shocks.
B Contact an Authorised Service Centre for repairs.
Do not overload the mains socket.
B If the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
B High voltages can cause fire or electric shocks.
B For any inspection, adjustment and repair work, please contact an
Authorised Service Centre.
Clean the mains plug regularly to prevent it from becoming covered in
dust.
B If dust builds up on the mains plug, the resulting humidity can damage the
insulation, which could result in fire. Pull the mains plug out from the
mains socket and wipe it with a dry cloth.
B If not using the projector for an extended period of time, pull the mains
plug out from the mains socket.
Page 7
ENGLISH-7
Preparation
Do not do anything that might damage the mains lead or the mains
plug.
B Do not damage the mains lead, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
B If the mains lead is used while damaged, electric shocks, short-circuits or
fire may result.
B Ask an Authorised Service Centre to carry out any repairs to the mains
lead that might be necessary.
Do not handle the mains plug with wet hands.
B Failure to observe this may result in electric shocks.
Insert the mains plug securely into the mains socket.
B If the plug is not inserted correctly, electric shocks or overheating could
result.
B Do not use plugs which are damaged or mains sockets which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
B If the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
B Failure to observe this may result in fire or electric shocks.
Do not place the projector on soft materials such as carpets or sponge
mats.
B Doing so may cause the projector to overheat, which can cause burns, fire
or damage to the projector.
Do not place liquid containers on top of the projector.
B If water spills onto the projector or gets inside it, fire or electric shocks
could result.
B If any water gets inside the projector, contact an Authorised Service
Centre.
Do not insert any foreign objects into the projector.
B Do not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Keep the batteries out of the reach of infants.
B If the batteries are swallowed, death by suffocation may result. If you
believe that the batteries may have been swallowed, seek medical advice
immediately.
Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.
B Failure to observe this may cause the batteries to leak, overheat, explode
or catch fire.
B Store the batteries in a plastic bag and keep them away from metallic
objects.
Page 8
8-ENGLISH
During a thunderstorm, do not touch the projector or the cable.
B Electric shocks can result.
Do not use the projector in a bath or shower.
B Fire or electric shocks can result.
Do not look into the lens while the projector is being used.
B Strong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
B Be especially careful not to let young children look into the lens. In
addition, disconnect the mains plug when you are away from the projector.
Do not place your hands or other objects close to the air outlet port.
B Heated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
B The lamp cover gets very hot, and contact with it can cause burns.
Before replacing the lamp, be sure to disconnect the mains plug from
the mains socket.
B Electric shocks or explosions can result if this is not done.
Caution
Do not cover the air inlet port or the air outlet port.
B Doing so may cause the projector to overheat, which can cause fire or
damage to the projector.
B Do not place the projector in narrow, badly ventilated places such as
closets or bookshelves.
B Do not place the projector on cloth or papers, as these materials could be
drawn into the air inlet port.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
B Using the projector under such conditions may result in fire or electric
shocks.
When disconnecting the mains lead, hold the plug, not the lead.
B If the mains lead itself is pulled, the lead will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
B Moving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
B Failure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Page 9
ENGLISH-9
Preparation
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
B Failure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct.
B If the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Use only the specified batteries.
B If incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Insulate the battery using tape or similar before disposal.
B If the battery comes into contact with metallic objects or other batteries, it
may catch fire or explode.
Do not put your weight on this projector.
B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children stand or sit on the projector.
If not using the projector for an extended period of time, disconnect the
mains plug from the mains socket.
B If dust builds up on the mains plug, the resulting humidity may damage
the insulation, which could result in fire.
B This projector continues to draw approximately 6 W of power even when
the power is turned off.
Disconnect the mains plug from the mains socket as a safety
precaution before carrying out any cleaning.
B Electric shocks can result if this is not done.
Do not install the accessory wireless card to any device other than the
card slot of the projector. (PT-LB10NTE only)
B If this is not observed, damage to the device may result.
Ask an Authorised Service Centre to clean inside the projector at least
once a year.
B If dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
B It is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorised Service Centre to
clean the projector when required. Please discuss with the Authorised
Service Centre regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company.
Page 10
10-ENGLISH
Card remote control unit
(TNQE239 x1)
Mains lead for
Continental Europe
(K2CM3DR00002 x 1)
Mains lead for U.K.
(K2CT3DR00005 x 1)
Lithium battery for
remote control unit
(CR2025 x1)
RGB signal cable
[1.8 m (5´10˝),
K1HA15DA0002 x1]
Accessories
Check that all of the accessories shown below have been included with your
projector.
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
AUTO
SETUP
VIDEO
INPUT
POWER
RGB
MENU
Carrying bag
(TPEP013 x 1)
CD-ROM
(TQBH9005 x1)
Wireless Card
(N5HBD0000029 x1)*
1
*1N5HBD0000031 x 1 for Spain
N5HBD0000030 x 1 for Singapore
N5HBD0000028 x 1 for Malaysia
Hexagon wrench
(TKLA0701
x1)
PT-LB10NTE only
Page 11
ENGLISH-11
Preparation
Before use
Caution when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory carrying bag. When placing the
projector inside the carrying bag, position it so that the lens is facing upward.
Do not put anything else in the bag other than the projector and the cables.
Cautions regarding setting-up
Avoid setting up in places which are subject to vibration or shocks.
The internal parts can be damaged, which may cause malfunctions or
accidents.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
You will need to purchase the separate installation kit (Model No.ET-PKC80).
Furthermore, all installation work should only be carried out by a qualified
technician.
If using this projector at high elevations (above 1 400 m), set the “FAN
CONTROL” to “HIGH”. (Refer to page 45.)
Failure to observe this may result in malfunctions.
Page 12
12-ENGLISH
Notes on use
In order to get the best picture quality
Draw curtains or blinds over any windows and turn off any fluorescent lights
near the screen to prevent outside light or light from indoor lamps from
shining onto the screen.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the lens cover.
Screen
Do not apply any volatile substances which may cause discolouration to the
screen, and do not let it become dirty or damaged.
Lamp
The lamp may need to be replaced earlier due to variables such as individual
lamp characteristics, usage conditions and the installation environment,
especially when the projector is subjected to continuous use for more than
10 hours or the power is frequently turned on and off.
Liquid crystal panel
The liquid crystal panel of the projector is built with very high precision
technology to provide fine picture details. Occasionally, a few non-active
pixels may appear on the screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your LCD.
Wireless card (PT-LB10NTE only)
Static electricity from the human body can damage the wireless card. To
prevent this, touch a nearby metallic object such as an aluminium sash or a
door knob to dissipate the static charge from your body.
Wireless card slot (PT-LB10NTE only)
Make sure that there are no foreign objects inside the slot when inserting the
wireless card. Failure to observe this may damage the card and the slot.
Page 13
ENGLISH-13
Preparation
Location and function of each part
# Projector control panel (page 16)
$ Zoom ring (page 25)
% Focus ring (page 25)
& Security lock
This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.
' Leg adjuster buttons (L/R) (page 25)
These buttons are used to unlock the front adjustable legs. Press to adjust
the angle of tilt of the projector.
( Lens cover
) Projection lens
* Remote control signal receptor (page 23)
+ Wireless card slot (PT-LB10NTE only) (page 18)
Insert the wireless card into here.
Projector <Top, right and front>
#$%
+
'
*
)
(
&
'
Page 14
14-ENGLISH
# Connector panel (page 15)
$ Air outlet port
Do not cover this port.
% Speaker
& Front adjustable legs (L/R) (page 25)
' Air inlet port, Air filter (page 52)
Do not cover this port.
( Lamp unit holder (page 53)
WARNING
Do not place your hands or other objects close to the air outlet port.
B Heated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.
Projector <Back and bottom>
NOTE:
B During projection of an image, the cooling fan will operate, emitting a
small noise as it operates. Turning the lamp on or off will cause this
noise to increase a little.
B By using the “OPTION2” menu to set “LAMP POWER” to “LOW”, the
operating sound of the fan can be reduced. (Refer to page 45.)
#
(
$%$
'
&
Page 15
ENGLISH-15
Preparation
Connector panel
# Power input socket (AC IN) (page 24)
The accessory mains lead is connected here.
Do not use any mains lead other than the accessory mains lead.
$ SERIAL connector (pages 21, 22 and 62)
This connector is used to connect a personal computer to the projector in
order to control the projector externally. (RS-232C compatible)
% RGB IN connector (pages 21 and 22)
This connector is used to input RGB signals and YPBPR signals.
& RGB OUT connector (page 21)
This connector is used to output RGB signals and YPBPR signals from the
RGB IN connector.
' S-VIDEO IN connector (pages 22 and 41)
This connector is used to input signals from S-VIDEO-compatible
equipment such as a video deck. The connector is S1 signal compatible,
and it automatically switches between 16:9 and 4:3 aspect ratios in
accordance with the type of signal being input.
( VIDEO IN connector (page 22)
This connector is used to input video signals from video equipment such
as a video deck.
) AUDIO IN L-R connectors (pages 21 and 22)
* Menu operation (on connector panel) (page 16)
$ %&' *)
(#
Page 16
16-ENGLISH
Menu
operation
<on connector
panel:page 15>
Remote control unit
Projector control panel
# RGB INPUT indicator
This indicator illuminates when a signal is being input to the RGB IN connector.
$ LAMP indicator (page 51)
This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.
#$%
'
(
&
)
*
+,
'
)
+
-
/
1
POWER
AUTO
SETUP
FREEZE
VOLUME D.ZOOM
INPUT
VIDEO RGB
ENTER
SHUTTER
STD
INDEX
WINDOW
MENU
PROJECTOR
(
*
,
.
0
2
Page 17
ENGLISH-17
Preparation
% TEMP indicator (page 50)
This indicator illuminates if an abnormally high temperature is detected inside
the projector or around it. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.
& Power indicator (pages 24, 26 and 27)
This indicator illuminates red when the projector is in standby mode, and it
illuminates green when a picture starts to be projected.
' POWER button (pages 24 and 26)
( INPUT buttons (page 25)
These buttons are used to switch the input signals from the connected
equipment.
) AUTO SETUP button (pages 25 and 28)
If this button is pressed while a picture is being projected, the projection
settings will be adjusted automatically in accordance with the signal being
input. In addition, the angle of tilt of the projector will be automatically
detected and adjusted in order to correct any keystone distortion.
* MENU button (pages 32 and 34)
This button is used to display the “MAIN MENU”. When a menu screen is
being displayed, this button can be used to return to a previous screen or
to clear the screen.
+ Arrow (
FFGGII
and HH) buttons (page 34)
These buttons are used to select and adjust items in the on-screen menus.
, ENTER button (page 34)
This button is used to accept and to activate items selected in the on-screen
menus.
- FREEZE button (page 29)
This button is used to momentarily freeze projection so that a still picture is
displayed.
. SHUTTER button (page 29)
This button is used to momentarily turn off the picture and sound.
/ VOLUME +/- buttons (page 30)
These buttons are used to adjust the volume of the sound output from the
projector’s built-in speaker. Refer to page 33 for details on how to adjust
the volume using the buttons on the projector control panel.
0 STD (standard) button (page 35)
This button is used to reset the projector adjustment values to the factory
default settings.
1 INDEX WINDOW button (page 31)
This button can be used to split the image projection area into a still
picture and a moving picture. When “NETWORK” is selected, screen
display will be switched between four window style and index style. (PTLB10NTE only. Refer to the accessory CD-ROM for details.)
2 D.ZOOM +/- buttons (page 30)
These buttons are used to enlarge the projected image.
Page 18
%
$
#
18-ENGLISH
Inserting the wireless card (PT-LB10NTE only)
Insert the wireless card before using the PT-LB10NTE.
Hexagon wrench
(accessory)
Card lock fixing
screw
# Insert the wireless card until it
locks.
$ Set the card lock.
% Fasten the card lock with the card
lock fixing screw using the
hexagon wrench.
The card lock is already installed at the factory default setting. When you
insert the wireless card, first remove the card lock fixing screw using the
hexagon wrench to release the card lock.
B When removing the wireless card, unlock the card lock, and then pull out
the wireless card.
Card lock
(PT-LB10NTE only)
Wireless card
# Connector
This connector is for connecting the wireless card to the projector’s card
slot. Be careful not to touch the connector.
$ Wireless card access indicator
Flashes while the projector is being accessed with personal computers by
means of a wireless network.
$
#
Page 19
ENGLISH-19
Getting started
Setting-up
Projection methods
In way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION2” menu. Refer
to page 45 for details.)
BFront-desk projection BFront-ceiling projection
BRear-desk projection
(Using a translucent screen)
BRear-ceiling projection
(Using a translucent screen)
Menu items Setting
FRONT
DESK
FRONT/REAR
DESK/CEILING
Menu items Setting
FRONT
CEILING
FRONT/REAR
DESK/CEILING
Menu items Setting
REAR
DESK
FRONT/REAR
DESK/CEILING
Menu items Setting
REAR
CEILING
FRONT/REAR
DESK/CEILING
NOTE:
B You will need to purchase the separate ceiling bracket (ET-PKC80)
when using the ceiling installation method.
B If you set up the projector vertically, it may cause
damage to the projector.
B It is recommended that you set up the projector
in a place that is tilted at less than
±30°. Setting
up the projector in places that are tilted at more
than
±30° may cause malfunctions.
Page 20
H1
L
L
SH
SW
81.2 mm
(3-3/16˝)
20-ENGLISH
NOTE:
B The dimensions in the table above are approximate.
B If you use the projection distance for the 16:9 screen,
the 4:3 projection image overflows the screen at the top
and bottom.
B For details about projected image distances, refer to
page 61.
Projector position
L: Projection distance
SH: Image height
SW:Image width
H1: Distance from centre
of lens to bottom edge
of projected image
Top edge of screen
Screen
Bottom edge of screen
Screen
Projection distances
0.84 m(33˝) 1.1 m(3´7˝) 1.1 m(3´7˝) 0.08 m(3-1/8˝)
1.02 m(40˝) 1.2 m(3´11˝) 1.4 m(4´7˝) 1.2 m(3´11˝) 1.4 m(4´7˝) 0.09 m
(3-17/32˝)
1.27 m(50˝) 1.5 m(4´11˝) 1.7 m(5´6˝) 1.5 m(4´11˝) 1.8 m(5´10˝) 0.11 m(4-5/16˝)
1.52 m(60˝) 1.8 m(5´10˝) 2.1 m(6´10˝) 1.8 m(5´10˝) 2.1 m(6´10˝) 0.14 m(5-1/2˝)
1.78 m(70˝) 2.1 m(6´10˝) 2.4 m(7´10˝) 2.1 m(6´10˝) 2.5 m(8´2˝) 0.16 m(6-9/32˝)
2.03 m(80˝) 2.4 m(7´10˝) 2.8 m(9´2˝) 2.4 m(7´10˝) 2.9 m(9´6˝) 0.18 m(7-1/16˝)
2.29 m(90˝) 2.7 m(8´10˝) 3.2 m(10´5˝) 2.8 m(9´2˝) 3.2 m(10´5˝) 0.20 m
(7-27/32˝)
2.54 m(100˝) 3.0 m(9´10˝) 3.5 m(11´5˝) 3.0 m(9´10˝) 3.6 m(11´9˝) 0.22 m
(8-21/32˝)
3.05 m(120˝) 3.6 m(11´9˝) 4.2 m(13´9˝) 3.7 m(12´1˝) 4.3 m(14´1˝) 0.26 m
(10-7/32˝)
3.81 m(150˝) 4.5 m(14´9˝) 5.3 m(17´4˝) 4.6 m(15´1˝) 5.4 m(17´8˝) 0.33 m
(12-31/32˝)
5.08 m(200˝) 6.0 m(19´8˝) 7.1 m(23´3˝) 6.1 m(20´) 7.3 m(23´11˝) 0.44 m
(17-5/16˝)
6.35 m(250˝) 7.5 m(24´7˝) 8.9 m(29´2˝) 7.6 m(24´11˝) 9.1 m(29´10˝) 0.55 m(21-5/8˝)
7.62 m(300˝) 9.0 m(29´6˝) 10.7 m(35´1˝) 9.2 m(30´2˝) 11.0 m(36´1˝) 0.66 m
(25-31/32˝)
Wide
(LW)
Telephoto
(LT)
Projection distance (L)
PT-LB10NTE/PT-LB10E/
PT-LB10SE
PT-LB10VE
Height
position
(H1)
Wide
(LW)
Telephoto
(LT)
4:3 Screen
size
(diagonal)
——
Page 21
ENGLISH-21
Getting started
Connections
Notes on connections
B Read the instruction manual for each peripheral device carefully before
connecting it.
B Turn off the power supply for all peripheral devices before making any
connections.
B If the cables necessary for connection are not included with the peripheral
device or available as an option, you may need to prepare a proper cable
for the device concerned.
B If there is a lot of jitter in the video signal, the projected image may flicker.
In such cases, it will be necessary to connect a TBC (time base corrector).
B Refer to the list on page 60 for details on compatible signals which can be
input to the projector.
B Only one audio system circuit is available for the AUDIO IN L-R
connectors, so if you change the audio input source, you will need to
remove and insert the appropriate plugs.
Connecting to computer
RGB signal cable
(accessory)
Computer
DIN 8-pin
(male)
Computer for
control use
Monitor
RGB signal cable
Refer to the accessory CDROM for details on the wireless
network that is used for
controlling the projector with a
personal computer by means
of the wireless card.
(PT-LB10NTE only)
Serial adapter
(ET-ADSER : sold
separately)
Page 22
22-ENGLISH
NOTE:
B If the signal cables are disconnected or if the power supply for the
computer or video deck is turned off while “D.ZOOM”(digital zoom) or
“INDEX WINDOW” is being used, these functions will be cancelled.
Connecting to video equipment
D-sub15-pin (male) - BNCx5 (male) adapter cable
DVD player
(with component
video connectors)
DIN 8-pin
(male)
DVD player Video deck
Computer for control use
Red (connect to PR signal connector)
Blue (connect to PB signal connector)
Green (connect to Y signal connector)
BNC/RCA adapter
Serial adapter
(ET-ADSER :
sold separately)
Page 23
ENGLISH-23
Getting started
Insert the accessory lithium battery while making sure that the polarities are correct.
# While pushing the battery holder tab to the right, pull out the battery
holder.
$ Insert the battery into the battery holder so that the + side is facing
upward.
% Insert the battery holder.
Preparation for the remote control unit
NOTE:
B Do not drop the remote control unit.
B Keep the remote control unit away from liquids.
B Remove the battery if not using the remote control unit for long periods.
B Use only CR2025 batteries as replacement batteries.
B If the remote control unit is held so that it is facing directly in front of the
remote control signal receptor, the operating range is within
approximately 7 m (23´) from the surfaces of the receptor. Furthermore,
the remote control unit can be operated from an angle of ±30° to the left
or right and ±15° above or below the receptors.
B If there are any obstacles in between the remote control unit and the
receptor, the remote control unit may not operate correctly.
B If strong light is allowed to shine onto the remote control signal receptor,
correct projector operation may not be possible. Place the projector as
far away from light sources as possible.
B
If facing the remote control unit toward the screen to operate the projector,
the operating range of the remote control unit will be limited by the amount
of light reflection loss caused by the characteristics of the screen used.
Push the tab
Pull out
Back side
Match the “+”
surface of the
battery with the
“+” marked side of
the battery holder.
Page 24
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
)
*
$
&
(
'
#
Turning on the power
Before turning on the power
1, Ensure that all peripheral
devices are connected
properly.
2, Remove the lens cover.
Lens cover
Mains lead
Connect the accessory mains lead to the AC IN
socket.
BThe power indicator on the projector will illuminate red.
Press the POWER button.
BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be
projected.
Turn on the power of all connected devices.
BStart the play function of a device such as a DVD player.
NOTE:
B
If the mains lead was disconnected during projection when the projector
was used the last time, projection will start after the mains lead is
connected (when “POWER MEMORY” in the “OPTION2” menu is set to
“ON”). Refer to page 46 for details.
B A tinkling sound may be heard when the lamp unit is turned on, but this
is not a sign of a malfunction.
#
$
%
24-ENGLISH
Power indicator
Page 25
ENGLISH-25
Basic Operation
Press the input select button to select the
input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
Press the AUTO SETUP button to initiate
automatic positioning.
BThe tilt of the projector and the input
signal will be detected and keystone
distortion and the position of the
image will be corrected.
(Refer to page 28 for details.)
Adjusting the size
BTurn the zoom ring to adjust the size of the projected image.
Adjusting the focus
BTurn the focus ring to adjust the focus of the projected image.
AUTO SETUP
Input select
buttons
Changing
signals
VIDEO
RGB
VIDEO
RGB
NETWORK
S-VIDEO
VIDEO
S-VIDEO
RGB
NETWORK
&
'
)
*
(
Adjusting the angle
BWhile pressing the adjuster buttons,
adjust the forward/back angle of tilt
of the projector. Adjust so that the
projector is as vertical to the screen
as possible.
BA picture will be projected in accordance with the selected input
signal.
BWhen a YPBPR signal is being input, “YPBPR” will be displayed
instead of “RGB”.
B“NETWORK” is for PT-LB10NTE only.
Page 26
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
ENTER
#
$
%
Turning off the power
Power indicator
Press the POWER button.
B“POWER OFF” is displayed on the
screen.
Press the IIor HHbutton to select “OK”, and
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The power indicator on the projector will illuminate orange while the
cooling fan is still operating.)
NOTE:
B You can also turn off the power by pressing the POWER button twice or
by holding it down for at least 0.5 seconds.
B When the projector is in standby mode (the power indicator on the
projector is illuminated red), the projector continues to draw approximately
6 W of power even when the cooling fan has stopped.
#
$
%
POWER OFF
OK CANCEL
Mains
lead
Disconnect the mains lead after the power
indicator on the projector illuminates red.
26-ENGLISH
Page 27
ENGLISH-27
Basic Operation
Power indicator
Power indicator status
Red
Illuminated
The projector is in standby mode and image projection
is possible by pressing the POWER button.
A picture is being projected.
The lamp is cooling down after the power is turned
off. (The cooling fan is operating.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated orange. (After a short period, a picture
will be projected.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated red. (After a short period, a picture will be
projected.)
Flashing
Illuminated
Illuminated
Flashing
Green
Orange
Projector status
Direct power off function
You can disconnect the mains lead during projection or immediately after
use and move the projector. The cooling fan will operate by the internal
power supply to cool down the lamp.
B When this function is used, it may take more time for the lamp to turn back
on again compared to when the lamp cools down with the mains lead
connected.
B Do not put the projector in a bag while the cooling fan is operating.
CAUTION
If not using the projector for an extended period of time, disconnect the
mains plug from the mains socket.
B If dust builds up on the mains plug, the resulting humidity may damage the
insulation, which could result in fire.
B This projector continues to draw approximately 6 W of power even when
the power is turned off.
Page 28
28-ENGLISH
Correcting keystone distortion and
automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone
distortion and the position of the image can then be corrected automatically
in accordance with the input signal.
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
Projector control panel
Press the AUTO SETUP button.
(When the projected image has caused keystone distortion)
B Automatic positioning
will be carried out.
Screen
Projected
image
[
NOTE:
B “AUTO SEARCH” will also be carried out. (When “AUTO SEARCH” is
set to “ON”, refer to page 44 for details.)
B When RGB signals are being input, “DOT CLOCK”, and “CLOCK
PHASE” will be adjusted automatically in addition to keystone distortion
and the position of the image being corrected (except when the dot clock
frequency is 100 MHz or higher). Refer to page 40 for details.
B If the edges of the projected image are indistinct, or if a dark picture is
being projected, the automatic setup processing may stop automatically
before it is complete. If this happens, project a different picture and then
press the AUTO SETUP button again.
B Set “AUTO KEYSTN” in the “OPTION1” menu to “OFF” to prevent any
deterioration of the picture as a result of keystone correction.
(Refer to page 44.)
Page 29
ENGLISH-29
Useful functions
Turning off the picture and sound
momentarily (SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in “SHUTTER” mode than it does
in normal projection mode.
ENTER
FREEZE
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
SHUTTER
ENTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
SHUTTER
FREEZE
Still picture
B The picture being projected will be paused.
B Press the FREEZE button again to cancel the
still picture.
Press the SHUTTER button.
B The picture and sound will be turned off.
B Press any button on either the projector or
remote control unit to return to normal operating
mode.
Press the FREEZE button.
NOTE:
B “SHUTTER” on the “MAIN MENU” is the same
function.
NOTE:
B The FREEZE button will be disabled when
“NETWORK” is selected. (PT-LB10NTE only)
Pausing a picture (FREEZE)
Page 30
30-ENGLISH
ENTER
INDEX
WINDOW
PROJECTOR
VOLUME
STD
VIDEO
INPUT
POWER
RGB
MENU
AUTO
SETUP
SHUTTER
FREEZE
D.ZOOM
B The picture will then
be enlarged to 1.5
times the normal size.
The remote control unit functions during D.ZOOM (digital zoom)
Press the F,G,IandHbuttons to move the enlarged area which you want to project.
Press the D.ZOOM +/- buttons to change the enlargement ratio.
Press the MENU button to return to the normal screen.
INDEX
WINDOW
PROJECTOR
STD
D.ZOOMVOLUME
[
Enlarging the picture (D.ZOOM)
Adjusting the volume (VOLUME)
Press the D.ZOOM +/- button.
Press the VOLUME +/- button.
B Press the + button to raise the volume.
B Press the - button to lower the volume.
NOTE:
B The enlargement ratio can be changed within the range of x1 to x2, in
steps of 0.1. When RGB signals are being input, the enlargement ratio
can be changed within the range of x1 to x3, except when the “FRAME
LOCK” is set to “ON”.
B If the type of signal being input changes while the digital zoom function
is being used, the digital zoom function will be cancelled.
NOTE:
B You can also select “VOLUME” from the
“MAIN MENU” to adjust the volume.
B The VOLUME button will be disabled when
“NETWORK” is selected. (PT-LB10NTE only)
Page 31
ENGLISH-31
Useful functions
ENTER
PROJECTOR
VOLUME D.ZOOM
STD
MENU
AUTO
SETUP
SHUTTER
FREEZE
INDEX
WINDOW
Still
picture
Moving
picture
The remote control unit functions during INDEX WINDOW
Press the F or G button to select a screen size.
It can switch to three stages.
Still
picture
Moving
picture
Still
picture
Moving
picture
Still
picture
Moving
picture
Press the IIor HHbutton to switch between the still picture screen
and moving picture screen.
Press the ENTER button to capture the present moving picture in a
still window.
Press the MENU button to return to the previous screen.
Still
picture
Moving
picture
Moving
picture
Still
picture
Displaying two screens (INDEX WINDOW)
This function lets you store a picture which is being projected into memory,
so that you can display a still picture and a moving picture on the screen.
B The aspect ratio of
the screen changes
and the image is
vertically elongated
in comparison to a
normal image.
B When “NETWORK”
is selected, screen
display will be switched between four window
style and index style. (PT-LB10NTE only. Refer
to the accessory CD-ROM for details.)
Press the INDEX WINDOW button.
NOTE:
B When the screen size is changed, the picture’s aspect ratio will also
change. Make sure that you fully understand the notes on “ASPECT” on
page 42 before using the “INDEX WINDOW” function.
B “INDEX WINDOW” on the “MAIN MENU” is the same function.
Page 32
32-ENGLISH
On-screen menus
Menu screens
The various settings and adjustments for
this projector can be carried out by
selecting the operations from on-screen
menus.
The general arrangement of these menus
is shown below.
MAIN MENU
MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION1
OPTION2
SECURITY
NETWORK
SELECT
ENTER EXIT
PICTURE
PICTURE MODE DYNAMIC
CONTRAST 32
BRIGHT 32
SHARPNESS 0
COLOR TEMP. STANDARD
W-BAL R 32
W-BAL G 32
W-BAL B 32
AI ON
SIGNAL MODE XGA
STANDARD
SELECT ADJ RETRN
PICTURE menu (page 37)
When an RGB signal is being input
or NETWORK is selected
PICTURE
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 6
COLOR TEMP. STANDARD
AI ON
SIGNAL MODE 480p
STANDARD
SELECT ADJ RETRN
When a YPBPRsignal is being input
PICTURE
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 8
COLOR TEMP. STANDARD
AI ON
TV-SYSTEM AUTO
STILL MODE OFF
STANDARD
SELECT ADJ RETRN
When an S-VIDEO/VIDEO
signal is being input
KEYSTONE correction (page 36)
KEYSTONE 0
B Keystone distortion of the on-screen
display will not be corrected.
B Press the MENU button to
display the “MAIN MENU”.
Refer to page 34 for details on
how to operate the on-screen
menus.
B When NETWORK is
selected, “W-BAL R/G/B”
settings will not be displayed.
(PT-LB10NTE only)
Page 33
ENGLISH-33
Adjustments and settings
POSITION menu (page 40)
When an RGB/YPBPR signal
is being input
OPTION1
OSD ON
AUTO SEARCH ON
AUTO SIGNAL ON
AUTO KEYSTN ON
RGB/YP
BPR
AUTO
VGA60/480p 480p
SXGA MODE SXGA
NR OFF
BLACKBOARD OFF
SELECT ADJ RETRN
OPTION1 menu (page 43)
OPTION2
BACK COLOR BLUE
FRONT/REAR FRONT
DESK/CEILING DESK
FAN CONTROL STANDARD
LAMP POWER HIGH
LAMP RUNTIME 10H
FUNC 1 INDEX
CONTROL KEY ON
AUTO POW.OFF DISABLE
POWER MEMORY ON
SELECT ADJ RETRN
OPTION2 menu (page 43)
SECURITY
INPUT PASSWD OFF
AMEND PASSWD
TEXT DISPLAY OFF
TEXT CHANGE
SELECT
ADJ RETRN
SECURITY menu (page 47)
POSITION
POSITION
DOT CLOCK 32
CLOCK PHASE 16
ASPECT 4:3
RESIZING ON
FRAME LOCK OFF
STANDARD
SELECT ENTER RETRN
POSITION
POSITION
ASPECT 4:3
RESIZING ON
STANDARD
SELECT ENTER RETRN
When an S-VIDEO/VIDEO
signal is being input
LANGUAGE ENGLISH
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT ENTER RETRN
LANGUAGE menu (page 43)
INDEX WINDOW function
(page 31)
SHUTTER function (page 29)
VOLUME adjustment
Press the ENTER button, and
then press the I or H button
to adjust the volume.
NETWORK
NETWORK 1
NAME CHANGE LB10NT
INPUT PASSWD OFF
AMEND PASSWD
WEB CONTROL ON
DEFAULT
SELECT ENTER RETRN
NETWORK menu (page 49)
(PT-LB10NTE only)
Page 34
34-ENGLISH
# Press the MENU button.
The “MAIN MENU”
will be displayed.
$ Press the FFor GGbutton to select an item.
Selected item will
be displayed in
blue.
% Press the ENTER button to accept the
selection.
The selected
menu screen or
adjustment
screen will then
be displayed.
(Example:
“PICTURE”
menu)
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR
VOLUME D.ZOOM
STD
VIDEO
INPUT
POWER
RGB
AUTO
SETUP
MENU
Menu operation guide
MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION1
OPTION2
SECURITY
NETWORK
SELECT
ENTER EXIT
MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION1
OPTION2
SECURITY
NETWORK
SELECT
ENTER EXIT
PICTURE
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 8
COLOR TEMP. STANDARD
AI ON
TV-SYSTEM AUTO
STILL MODE OFF
STANDARD
SELECT ADJ RETRN
NOTE:
B Press the MENU
button to return to
the previous
screen.
Menu operation
(on connector panel)
Page 35
ENGLISH-35
Adjustments and settings
& Press the FFor GGbutton to select
an item, and then press the IIor
HH
button to change or adjust the
setting.
An individual adjustment screen
such as the one shown below will
be displayed for bar scale items.
The bar scale will turn green when
any adjustment changes the setting
from the factory set value.
Unavailable on-screen
menu items
This projector has unadjustable
items and unusable functions
depending on the signal being
input.
When an item cannot be adjusted
or a function cannot be used, the
corresponding on-screen menu
display does not appear, and the
item or function will not work even
if the ENTER button is pressed.
Returning a setting to the factory default
If you press the STD (standard) button on the remote control unit, you can
return settings to the factory default settings. However, the operation of this
function varies depending on which screen is being displayed.
B When a menu screen is being
displayed
All items displayed will be returned
to their factory default settings,
“STD” will be displayed in the topright screen and the bar scale will
appear white.
B When an individual adjustment
screen is being displayed
Only the item displayed will be
returned to the factory default
setting, and the bar scale will
appear white.
NOTE:
B You can also select
“STANDARD” from the menu
screen and then press the
ENTER button.
PICTURE STD
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 8
COLOR TEMP. STANDARD
AI ON
TV-SYSTEM AUTO
STILL MODE OFF
STANDARD
SELECT ENTER RETRN
BRIGHT 32
BRIGHT 32
NOTE:
B
Triangle symbols above and below
the bar scale indicate the factory
default setting. Items which do not
have these triangle symbols
cannot be returned to the factory
default setting.
Indicates the standard factory
default setting
Indicates the current
adjustment value
B The positions of triangle
symbols vary depending on the
type of signal being input.
Page 36
36-ENGLISH
Correcting keystone distortion
Keystone distortion is corrected automatically when the projector’s automatic
setup function is used, but this correction will not apply if the screen itself is
tilted. In such cases, you can correct the keystone distortion manually with
the following procedure.
Vertical
keystone
distortion
correction
Operation
Press the HHbutton. Press the IIbutton.
KEYSTONE 0
NOTE:
B If you press the AUTO SETUP button after correcting the keystone
distortion manually, the automatic keystone correction function will
operate and the corrected picture will return to its previous incorrect
condition. To prevent this from happening, you can set “AUTO
KEYSTN” in the “OPTION1” menu to “OFF”. (Refer to page 44.)
B Vertical keystone distortion can be corrected to ±30° of the angle of tilt.
However, the greater the correction amount, the more the picture
quality will deteriorate, and the harder it will become to achieve a good
level of focus. To obtain the best picture quality, set up the projector
and screen in such a way that the amount of keystone correction
required is as minimal as possible.
B The picture size will also change when correction of keystone distortion
is carried out.
Vertical keystone distortion correction only.
Page 37
ENGLISH-37
Adjustments and settings
Press the F or G button on the
projector or remote control unit to
select an item, and then press the
I or H button to change the
setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then press the I or H button
to make the adjustment.
When an S-VIDEO/VIDEO signal is
being input
Adjusting the picture
PICTURE
PICTURE MODE DYNAMIC
CONTRAST 32
BRIGHT 32
SHARPNESS 0
COLOR TEMP. STANDARD
W-BAL R 32
W-BAL G 32
W-BAL B 32
AI ON
SIGNAL MODE XGA
STANDARD
SELECT ADJ RETRN
PICTURE
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 8
COLOR TEMP. STANDARD
AI ON
TV-SYSTEM AUTO
STILL MODE OFF
STANDARD
SELECT ADJ RETRN
When an RGB signal is being input
or NETWORK is selected
PICTURE
PICTURE MODE STANDARD
CONTRAST 32
BRIGHT 32
COLOR 32
TINT 32
SHARPNESS 6
COLOR TEMP. STANDARD
AI ON
SIGNAL MODE 480p
STANDARD
SELECT ADJ RETRN
When an YPBPR signal is being
input
When NETWORK is selected, “WBAL R/G/B” settings will not be
displayed. (PT-LB10NTE only)
PICTURE MODE NATURAL
[
STANDARD
[
DYNAMIC
[
BLACK-BD
PICTURE MODE
Select the picture mode that best
matches the image source and
room conditions.
The mode best used in dark rooms
is “NATURAL”. For rooms having
regular lighting conditions in use,
select “STANDARD”. For
exceptionally bright rooms, use
“DYNAMIC”.
“BLACK-BD” is for the PT-
LB10NTE/PT-LB10E/PT-LB10SE
only. This item is available only
when “BLACKBOARD” in the
“OPTION1” menu is set to “ON”.
Select “BLACK-BD” when projecting
onto blackboards.
Page 38
38-ENGLISH
CONTRAST
This adjusts the contrast of the
picture. (Adjust the “BRIGHT”
setting first if required before
adjusting the “CONTRAST” setting.)
The picture is bright: I button
The picture is dark: H button
BRIGHT
This adjusts the darker areas (black
areas) in the picture.
Black areas are too light: I button
Dark areas are too solid: H button
COLOR
(S-VIDEO/VIDEO/YPBPR
only)
The colour is too deep: I button
The colour is too pale: H button
TINT
(NTSC/NTSC 4.43/YPBPR only)
This adjusts the flesh tones in the
picture.
The flesh tones are greenish:
I button
The flesh tones are reddish:
H button
SHARPNESS
To soften the picture details:
I button
To sharpen the picture details:
H button
COLOR TEMP.
This is used to adjust the white
areas of the picture if they appear
bluish or reddish.
White balance R/G/B
(W-BAL R/G/B)
(RGB only)
This is used to adjust the white
areas of the picture if they appear
colourised.
To make the selected colour lighter
:
I button
To make the selected colour stronger
:
H button
AI
ON
The lamp is controlled according to
the input signals to project images
with the best quality.
OFF
“AI” is disabled.
COLOR TEMP. STANDARD
[
HIGH
[
LOW
NOTE:
B “AI” is disabled when “LAMP
POWER” is set to “LOW”.
(Refer to page 45.)
Page 39
SIGNAL MODE
(RGB/YPBPR/NETWORK only)
This displays the type of signal
which is currently being projected.
Refer to the list on page 60 for
details on each type of signal.
sRGB is an international colour
reproduction standard (IEC61966-2-
1) established by the International
Electrotechnical Commission (IEC).
If you would like the colours in
sRGB-compatible pictures to be
reproduced more faithfully, make
the following settings.
##
Press the
FF
or
GG
button to
select “PICTURE MODE”, and
then press the
II
or
HH
button
to select “NATURAL”.
$$
Press the STD (standard)
button on the remote control
unit.
%%
Press the
FF
or
GG
button to
select “COLOR TEMP.”, and
then press the
II
or
HH
button
to select “STANDARD”.
ENGLISH-39
Adjustments and settings
STILL MODE
(S-VIDEO/VIDEO only)
To reduce flickering of still images
(vertical flicker), set “STILL MODE”
to “ON”.
NOTE:
B sRGB is only enabled when
RGB signals are being input
(when “LAMP POWER” is set
to “HIGH” and “AI” is set to
“OFF”).
Projecting sRGBcompatible pictures
This should normally be set to
“AUTO”. If the signal is of such poor
quality that the correct format
cannot be automatically
distinguished, change the setting
manually to the required TV system.
TV-SYSTEM AUTO
[
NTSC
[
NTSC4.43
[
PAL
[
PAL-M
[
PAL-N
[
SECAM
TV-SYSTEM
(S-VIDEO/VIDEO only)
NOTE:
B When set to “AUTO”, the
projector automatically
distinguishes between
NTSC/NTSC 4.43/PAL/PAL60/
PAL-M/PAL-N/SECAM signals.
NOTE:
B Set to “OFF” when playing
back moving images.
Page 40
40-ENGLISH
Press the F or G button on the
projector or remote control unit to
select an item, and then press the I
or H button to change the setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then press the I or H button
to make the adjustment.
When an RGB/YP
BPR signal is
being input
When an S-VIDEO/VIDEO signal is
being input
POSITION
Moves the picture position.
Press the ENTER button to display the
“POSITION” screen.
Press the I or H button to move the
picture horizontally.
Press the F or G button to move the
picture vertically.
DOT CLOCK
(RGB only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, press the
I or H button to adjust so that any
such noise is minimised.
CLOCK PHASE
(RGB/YPBPR only)
Adjust the “DOT CLOCK” setting
first before carrying out this
adjustment. Press the I or H
button to adjust so that the noise
level is least noticeable.
Adjusting the position
POSITION
POSITION
DOT CLOCK 32
CLOCK PHASE 16
ASPECT 4:3
RESIZING ON
FRAME LOCK OFF
STANDARD
SELECT ENTER RETRN
POSITION
POSITION
ASPECT 4:3
RESIZING ON
STANDARD
SELECT ENTER RETRN
When an RGB signal is being
input, press the AUTO SETUP
button first to initiate automatic
positioning. If the optimum setting
is not obtained when “AUTO
SETUP” is carried out, adjust by
the following procedure.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or
higher are being input,
interference may not be
completely eliminated when
the “DOT CLOCK” and
“CLOCK PHASE” adjustments
are carried out.
POSITION H 64
V 32
Page 41
ENGLISH-41
Adjustments and settings
S4:3
The size of the input signal is
compressed to 75% and projected.
(This is useful for projecting a
picture with a 4:3 aspect ratio onto a
16:9 screen.)
AUTO
(S-VIDEO only)
When an S1 video signal is being
input, the aspect ratio is changed
automatically to project a 16:9
picture.
4:3
The input signal is projected without
change.
16:9
The picture is compressed to a ratio
of 16:9 and projected.
ASPECT
(S-VIDEO/VIDEO/480i, 576i, 480p
and 576p YPBPR only)
ASPECT AUTO
[
4:3
[
16:9
[
S4:3
S1 video signals
B
S1 video signals are a type of
video signal with an aspect ratio
of 16:9 which include a detector
signal. This detector signal is
output by some sources such as
wide-vision video decks.
B
When “ASPECT” is set to
“AUTO”, the projector recognizes
the detector signal and
automatically switches the aspect
ratio to 16:9.
When a horizontally
squeezed signal is
being input.
When a 4:3 signal
is being input.
[
[
When using the 16:9 screen
Page 42
42-ENGLISH
RESIZING
This should normally be set to “ON”.
(This setting is only for signals
which have lower resolutions than
the LCD panels. Refer to page 60
for details.)
ON
The pixel resolution of the input
signal is converted to the same
resolution as the LCD panels before
being projected. For signals with
lower resolutions, gaps in the pixels
are automatically interpolated into
the picture before it is projected.
This may sometimes cause
problems with the quality of the
picture.
OFF
The input signal is projected at its
original resolution, with no pixel
conversion. The projected picture
will be smaller than normal, so
adjust the zoom setting or move the
projector forwards or backwards to
adjust the picture size if necessary.
If set to “OFF”, some features, such
as “D.ZOOM” (digital zoom),
“KEYSTONE” or “INDEX WINDOW”
will not function.
FRAME LOCK
If the picture’s condition is bad while
a RGB moving picture is projected,
set “FRAME LOCK” to “ON”. Refer
to page 60 for compatible RGB
signals.
NOTE:
B If a selected mode does not
match the aspect ratio of the
input signal, it may affect the
quality of viewing of the
original picture. Keep this in
mind when selecting the
aspect ratio.
B If using this projector in places
such as cafes or hotels to
display programmes for a
commercial purpose or for
public presentation, note that if
the aspect ratio (16:9)
selection function is used to
change the aspect ratio of the
screen picture, you may be
infringing the rights of the
original copyright owner for
that programme under
copyright protection laws.
B If a normal (4:3) picture which
was not originally intended for
wide-screen viewing is
projected onto a wide screen,
distortion may occur around
the edges of the picture, or
part of the picture may not be
visible. Such programmes
should be viewed in 4:3 mode
to give proper consideration to
the aims and intentions of the
original programme’s creator.
Page 43
ENGLISH-43
Adjustments and settings
Changing the display language
Press the F or G button on the projector or remote control unit to select a
language, then press the ENTER button to accept the setting.
Indicates the language which is
currently set.
LANGUAGE ENGLISH
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
SELECT ENTER RETRN
Option settings
Press the F or G button on the
projector or remote control unit to
select an item, then press the I or
H button to change the setting.
OSD
ON
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
OFF
Use this setting when you do not
want the signal name to be
displayed.
OPTION2
BACK COLOR BLUE
FRONT/REAR FRONT
DESK/CEILING DESK
FAN CONTROL STANDARD
LAMP POWER HIGH
LAMP RUNTIME 10H
FUNC 1 INDEX
CONTROL KEY ON
AUTO POW.OFF DISABLE
POWER MEMORY ON
SELECT ADJ RETRN
NOTE:
B The setting for “TV-SYSTEM”
will also be displayed when an
S-VIDEO/VIDEO signal is being
input.
OPTION1
OSD ON
AUTO SEARCH ON
AUTO SIGNAL ON
AUTO KEYSTN ON
RGB/YP
BPR
AUTO
VGA60/480p 480p
SXGA MODE SXGA
NR OFF
BLACKBOARD OFF
SELECT ADJ RETRN
Page 44
44-ENGLISH
AUTO SEARCH
This should normally be set to “ON”
ON
When the power is turned on and
“AUTO SETUP” is running, the
projector detects which signals are
being input, and uses these signals
for projection.
(If a picture is being projected, the
signal source is not automatically
changed.)
OFF
Use this setting when you do not
want the signal source to be
changed automatically when the
power is turned on and “AUTO
SETUP” is running.
AUTO SIGNAL
This should normally be set to “ON”.
ON
“AUTO SETUP” will be carried out
automatically when the input signal
is changed.
OFF
“AUTO SETUP” will not function
when the input signal is changed.
AUTO KEYSTN
This should normally be set to “ON”.
ON
During “AUTO SETUP”, the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during “AUTO
SETUP”, such as when the screen
itself is at an angle.
RGB/YPBPR
This should normally be set to
“AUTO”. RGB or YPBPR is selected
automatically depending on the
synchronising signal status.
When 480i, 576i, 480p, 576p,
1 080/60i, 1 080/50i, 720/60p and
some VGA480 signals are being
input, select “RGB” or “YP
BPR
” in
accordance with the input signal.
VGA60/480p
Set to “VGA60” when 59.9Hz
VGA480 signals are being input
(refer to page 60 for details). Set to
“480p” when 480p RGB signals are
being input.
SXGA MODE
This setting is only for an SXGA
signal.
SXGA
Select this item normally.
SXGA+
When the edges of the projected
image are not visible, select this
item.
RGB/YPBPR AUTO
[
RGB
[
YPBP
R
VGA60/480p 480p
[
VGA60
SXGA MODE SXGA
[
SXGA+
Page 45
ENGLISH-45
Adjustments and settings
Noise Reduction (NR)
(S-VIDEO/VIDEO only)
If noise occurs from the projector
because of a poor input signal, set
“NR” to “ON”.
To turn off the “NR” feature, set it to
“OFF”.
BLACKBOARD
(PT-LB10NTE/PT-LB10E/
PT-LB10SE only)
Set to “ON” when “PICTURE
MODE” is set to “BLACK-BD”.
(Refer to page 37.)
BACK COLOR
This sets the colour which is
projected onto the screen when no
signal is being input to the projector.
FRONT/REAR
This setting should be changed in
accordance with the projector
setting-up method.
(Refer to page 19.)
FRONT
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
DESK/CEILING
This setting should be changed in
accordance with the projector
setting-up method.
(Refer to page 19.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced. This can help to extend
the lamp’s operating life. If using the
projector in small rooms where high
luminance is not required, it is
recommended that you set the
“LAMP POWER” to “LOW”.
BACK COLOR BLUE
[
BLACK
FRONT/REAR FRONT
[
REAR
DESK/CEILING DESK
[
CEILING
LAMP POWER HIGH
[
LOW
FAN CONTROL STANDARD
[
HIGH
NOTE:
B “LAMP POWER” cannot be set
when no signal is being input.
Page 46
46-ENGLISH
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 54, and reset “LAMP
RUNTIME” to “0”.
FUNC 1
This assigns a function to the
FUNC1 button of the ET-RM300
wireless remote control unit (sold
separately).
INDEX
Functions in the same way as the
INDEX WINDOW button on the
accessory card remote control unit.
(page 31)
KEYSTONE
Functions in the same way as when
“KEYSTONE” is selected from the
“MAIN MENU”. (page 36)
CONTROL KEY
To disable the buttons on the
projector, set “CONTROL KEY” to
“OFF”. A confirmation screen will
then be displayed. Select “OK” by
using I or H button. To use the
buttons on the projector, set to “ON”
by using the remote control unit.
AUTO POW.OFF
If no signal is input to the projector
for the duration of the period you
set, the projector will return to
standby mode. The period can be
set from 15 minutes to 60 minutes
in 5 minute intervals. If you don’t
use this feature, set it to “DISABLE”.
This feature will not function when
using the “FREEZE” function.
POWER MEMORY
This sets the projector’s start up
status for when the mains lead is
connected.
ON
The projector will start from the
same status as when the mains
lead was disconnected. If the mains
lead was disconnected during
projection when the projector was
used the last time, projection will
start after the mains lead is
connected.
OFF
The projector will be in standby
mode.
FUNC1 INDEX
[
KEYSTONE
NOTE:
B The lamp’s operating life varies
depending on the usage
conditions (such as the “LAMP
POWER” setting and the
number of times the power is
turned on and off).
Page 47
ENGLISH-47
Adjustments and settings
Setting up the security function
This projector is equipped with a security function. A password input screen
can be displayed, or a company URL can be set up and displayed at the
bottom of the projected image.
Press the F or G button on the
projector or remote control unit to
select “SECURITY”, then press the
ENTER button.
MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION1
OPTION2
SECURITY
NETWORK
SELECT
ENTER EXIT
PASSWORD
OK
RETURN
AMEND PASSWD
NEW
CONFIRM
OK
RETURN
SECURITY
INPUT PASSWD OFF
AMEND PASSWD
TEXT DISPLAY OFF
TEXT CHANGE
SELECT
ADJ RETRN
INPUT PASSWD
The password input screen can be
displayed when the power is turned
on. All of the controls other than the
POWER button are disabled unless
the password is entered correctly.
ON
“INPUT PASSWD” is enabled.
OFF
“INPUT PASSWD” is disabled. The
password input screen will not be
displayed when the power is turned
on.
AMEND PASSWD
Passwords can be changed. Press
the ENTER button to display the
“AMEND PASSWD” screen.
# Set a password by pressing the
F,G,I, and H buttons.
(A maximum of 8 buttons can be
set.)
$ Press the ENTER button.
% Enter the password again for
confirmation.
& Press the ENTER button.
Password change will be
completed.
(When you use the “SECURITY”
function for the first time)
Press the F, H, G, I, F, H, G
and I buttons in order, then press
the ENTER button.
(When a password change has
been made before)
Type in the changed password, then
press the ENTER button.
Page 48
48-ENGLISH
TEXT DISPLAY
You can set text to be displayed at
the bottom of the projected image at
all times.
ON
“TEXT DISPLAY” is enabled.
OFF
“TEXT DISPLAY” is disabled.
TEXT CHANGE
The text which is displayed when
“TEXT DISPLAY” is set to “ON” can
be changed.
Press the ENTER button to display
the “TEXT CHANGE” screen.
# Press the F, G, I and H
buttons to select the characters,
then press the ENTER button.
(You can enter 22 characters
continuously.)
C Select “BS” to delete a
character.
$ Press the F, G, I and H
buttons to select “OK”, then press
the ENTER button.
C Select “Cancel” to cancel the
change.
NOTE:
B The entered password will
appear as . It will not be
displayed on the screen.
B If you enter the wrong
password, the letters
“PASSWORD” and “NEW” will
become red. Enter the correct
password again.
BS OK
Cancel
TEXTCHANGE
ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯ
ＰＱＲＳＴＵＶＷＸＹＺ；：，．
ａｂｃｄｅｆｇｈｉｊｋｌｍｎｏ
ｐｑｒｓｔｕｖｗｘｙｚ／＋−＊
０１２３４５６７８９ ＿＠［］
Page 49
ENGLISH-49
Network setup (PT-LB10NTE only)
You need to make adjustments on some items when controlling the projector
with a personal computer by means of the wireless network. Refer to the
accessory CD-ROM for details.
INPUT PASSWD
Set to “ON” if you want password
confirmation to be used when
controlling the projector with a
personal computer by means of the
wireless network.
AMEND PASSWD
Passwords can be changed.
WEB CONTROL
To control the projector with a
personal computer by means of the
wireless network, set the “WEB
CONTROL” to “ON”.
DEFAULT
Network settings can be returned to
the factory default settings.
NETWORK
Select the network setting you want
to use.
NAME CHANGE
The name for this projector can be
set.
NETWORK
NETWORK 1
NAME CHANGE LB10NT
INPUT PASSWD OFF
AMEND PASSWD
WEB CONTROL ON
DEFAULT
SELECT ENTER RETRN
Adjustments and settings
Page 50
50-ENGLISH
When the TEMP indicator and the LAMP indicator are illuminated
There are two indicators on the control panel of the projector which give
information about the operating condition of the projector. These indicators
illuminate or flash to warn you about problems that have occurred inside the
projector, so if you notice that one of the indicators is on, turn off the power
and check the table below for the cause of the problem.
Problem
Indicator
display
The surrounding temperature or
the temperature inside the
projector has become unusually
high.
Illuminated (red)
(Lamp unit on)
B The ventilation holes may be covered.
B The ambient temperature in the place of use may be too high.
B The air filter may be blocked.
B Uncover the ventilation holes.
B Set up the projector in a place where the temperature is
between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is
between 20% and 80% (with no condensation). [If you set the
“FAN CONTROL” to “HIGH” (page 45), set up the projector in a
place where the temperature is between 0 °C (32 °F) and 35 °C
(95 °F) and the humidity is between 20% and 80% (with no
condensation).]
B Disconnect the mains lead by following the procedure on page
26, and then clean the air filter. (Refer to page 52)
Possible
cause
Remedy
The surrounding temperature or
the temperature inside the
projector has become
dangerously high, causing the
lamp unit to automatically shut
off.
Flashing (red)
(Lamp unit off)
TEMP indicator
LAMP indicator
TEMP indicator
Page 51
ENGLISH-51
Care and maintenance
Remedy
Problem
Indicator
display
Flashing (red)
It is nearly time to
replace the lamp
unit.
Illuminated (red)
An abnormality has been detected in the lamp
circuit.
B Does “REPLACE
LAMP” appear on
the screen after
the projector is
turned on?
B This occurs when
the operation time
for the lamp unit is
nearing 1 800
hours (when
“LAMP POWER”
has been set to
“HIGH”). Ask your
dealer or an
Authorised
Service Centre to
replace the lamp
unit.
Possible
cause
B The power may
have been turned
on straight away
after it was turned
off.
B Wait for a while
until the lamp unit
cools down before
turning the power
back on again.
B There may be an
abnormality in the
lamp circuit.
B Disconnect the
mains lead by
following the
procedure on
page 26, and then
contact an
Authorised
Service Centre.
LAMP indicator
NOTE:
B Be sure to disconnect the mains lead by following the procedure given
in “Turning off the power” on page 26 before carrying out any of the
procedures in the “Remedy” column.
B If the power turns off after the TEMP indicator has illuminated, it means
an abnormality has occurred. Please contact an Authorised Service
Centre so that the necessary repairs can be made.
Page 52
52-ENGLISH
Cleaning and replacing the air filter
If the air filter becomes clogged with dust, the internal temperature of the
projector will rise, the TEMP indicator will illuminate and the projector’s
power will turn off (the TEMP indicator will flash after the power is turned off).
The air filter should be cleaned every 100 hours of use.
% Replace the air filter, and then
install the air filter cover.
Cleaning
Use a vacuum cleaner to clean off
any accumulated dust.
Replacement procedure
# Turn off the power and
disconnect the mains lead.
Be sure to disconnect the mains
lead by following the procedure
given on page 26.
$ Gently turn the projector
upside down, and then remove
the air filter cover.
NOTE:
B If the dust cannot be cleaned
by a vacuum cleaner, remove
the air filter and soak it in
water, and then wash out the
dust by hand. Be sure to install
the air filter after it has dried.
B Do not use detergent when
washing the air filter.
B If the dust cannot be removed
by cleaning, it is time to
replace the air filter. Please
consult your dealer.
Furthermore, if the lamp unit is
being replaced, replace the air
filter at this time also.
NOTE:
B Be sure to install the air filter
before using the projector. If
the projector is used without
the air filter installed, dust and
other foreign particles will be
drawn into the projector, and
malfunctions will result.
Air filter cover
Air filter
Air filter cover
Page 53
ENGLISH-53
Care and maintenance
Replacing the lamp unit
Warning
When replacing the lamp, allow it
to cool for at least one hour
before handling it.
B The lamp cover gets very hot,
and contact with it can cause
burns.
Notes on replacing the lamp
unit
B The light generating lamp is
made of glass, so dropping it or
allowing it to hit hard objects may
cause it to burst. Be careful when
handling the lamp.
B Dispose of the removed old lamp
with the same care that would be
taken with a fluorescent light.
B A Phillips screwdriver is
necessary for removing the lamp
unit.
Lamp unit replacement
period
The lamp is a consumable product.
Even when the full life of the bulb
has not been exhausted, the
brightness of the light will gradually
decline. Therefore periodic
replacement of the lamp is
necessary.
The intended lamp replacement
interval is 2 000 hours, but it is
possible that the lamp may need to
be replaced earlier due to variables
such as a particular lamp’s
characteristics, usage conditions
and the installation environment.
Early preparation for lamp
replacement is encouraged.
The lamp will automatically shut off
after approximately 10 minutes
when 2 000 hours of use have been
reached because of a much greater
chance of it exploding after this
time.
NOTE:
B The projector is not supplied
with a replacement lamp unit.
Please ask your dealer for
details. Lamp unit product
no.: ET-LAB10
CAUTION:
B Do not use any lamp unit other
than the one with the product
number indicated above.
NOTE:
B The usage hours explained
above are for when “LAMP
POWER” in the “OPTION2”
menu has been set to “HIGH”
and when “AI” in the
“PICTURE” menu has been set
to “OFF”. If “LAMP POWER” is
set to “LOW”, or “AI” is set to
“ON”, the life of the lamp can
be extended.
B While 2 000 hours is the
intended replacement interval,
it is not a period of time
covered by warranty.
Page 54
B
A
54-ENGLISH
Lamp unit replacement procedure
# Disconnect the mains lead
from the projector by following
the procedure on page 26, and
check that the area around the
lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover.
% Use a Phillips screwdriver to
loosen the two lamp unit fixing
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B.
LAMP indicatorOn-screen display
Illuminates red during
image projection and
standby mode.
Displayed for 30
seconds. Pressing any
button will clear the
display.
More than 1 800 hours
Remains displayed until
any button is pressed.
More than 2 000 hours
NOTE:
B
If the lamp usage time has passed 2 000 hours (when “LAMP POWER” has
been set to “HIGH” and when “AI” has been set to “OFF”), the projector will
switch to standby mode after approximately 10 minutes of operation. The
steps )to -on the next page should thus be completed within 10 minutes.
Handle
Lamp unit cover
Lamp unit cover fixing screws
Lamp unit fixing screws
Page 55
ENGLISH-55
Care and maintenance
+ Press the ENTER button to
display the “OPTION2” menu,
and then press the F or G
button to select “LAMP
RUNTIME”.
, Press and hold the ENTER
button for approximately 3
seconds.
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
- Turn off the power.
This will reset the cumulative usage
time for the lamp unit to
“0”
.
Refer to page 26 for details on
how to turn off the power.
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
( Connect the mains lead.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the “MAIN MENU”, and
then press the F or G button
to select “OPTION2”.
MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION1
OPTION2
SECURITY
NETWORK
SELECT
ENTER EXIT
OPTION2
BACK COLOR BLUE
FRONT/REAR FRONT
DESK/CEILING DESK
FAN CONTROL STANDARD
LAMP POWER HIGH
LAMP RUNTIME 1820H
FUNC 1 INDEX
CONTROL KEY ON
AUTO POW.OFF DISABLE
POWER MEMORY ON
SELECT RETRN
OPTION2
BACK COLOR BLUE
FRONT/REAR FRONT
DESK/CEILING DESK
FAN CONTROL STANDARD
LAMP POWER HIGH
TIME RESET [POWER OFF]
FUNC 1 INDEX
CONTROL KEY ON
AUTO POW.OFF DISABLE
POWER MEMORY ON
SELECT RETRN
NOTE:
B
Be sure to install the lamp unit
and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection
circuit to operate so that the
power cannot be turned on.
NOTE:
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
NOTE:
B If the mains lead was
disconnected during projection
when the projector was used
the last time, projection will start
after the mains lead is
connected (when “POWER
MEMORY” in the “OPTION2”
menu is set to “ON”). Refer to
page 46 for details.
Page 56
56-ENGLISH
Before calling for service
Before calling for service, check the following points.
Problem Possible cause
Page
Power does not
turn on.
No picture
appears.
The picture is
fuzzy.
The colour is
pale or grayish.
No sound can
be heard.
The remote
control unit
does not
operate.
The buttons on
the projector do
not function.
B The mains lead may not be connected.
B The main power supply is not being supplied to the
mains socket.
B TEMP indicator is illuminated or flashing.
B LAMP indicator is illuminated or flashing.
B The lamp unit cover has not been securely
installed.
B The video signal input source may not be
connected properly.
B The input selection setting may not be correct.
B The “BRIGHT” adjustment setting may be at the
minimum possible setting.
B The “SHUTTER” function may be in use.
B The lens cover may still be attached to the lens.
B The lens focus may not have been set correctly.
B The projector may not be at the correct distance
from the screen.
B The lens may be dirty.
B The projector may be tilted too much.
B “COLOR” or “TINT” adjustment may be incorrect.
B The input source which is connected to the
projector may not be adjusted correctly.
B The audio signal source may not be connected
properly.
B The volume adjustment may be at the lowest
possible setting.
B The battery may be weak.
B The battery may not be inserted correctly.
B The remote control signal receptor on the projector
may be obstructed.
B The remote control unit may be out of the
operation range.
B The “CONTROL KEY” may be set to “OFF”.
In order to set the “CONTROL KEY” to “ON”
without using the remote control unit, keep holding
down the ENTER button on the projector and press
the MENU button for more than 2 seconds.
–
–
50
51
–
–
25
38
29
–
25
20
–
20
38
–
–
30,
33
–
23
23
23
46
Page 57
ENGLISH-57
Care and maintenance
The picture does
not display
correctly.
Picture from
computer does
not appear.
Problem Possible cause
B The signal format (“TV-SYSTEM”) may not be set
correctly.
B There may be a problem with the video tape or
other signal source.
B A signal which is not compatible with the projector
may be being input.
B The cable may be too long.
B The external video output for the laptop computer
may not be set correctly.
(You may be able to change the external output
settings by pressing the [Fn]+[F3] or [Fn]+[F10]
keys simultaneously. The actual method varies
depending on the type of computer, so refer to the
documentation provided with your computer for
further details.)
B If an RGB INPUT indicator is turned off, the video
signals may not be output from the computer.
Page
39
–
60
–
–
16
Before carrying out cleaning and maintenance, be
sure to disconnect the mains plug from the mains
socket.
Wipe the cabinet with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in water with a small amount
of neutral detergent in it, squeeze the cloth very well, and then wipe the
cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a
chemically-treated cloth, read the instructions supplied with the cloth before
use.
Do not wipe the lens with a cloth that is dusty or which produces lint.
If any dust or lint gets onto the lens, such dust or lint will be magnified and
projected onto the screen. Use a blower to clean any dust and lint from the
lens surface, or use a soft cloth to wipe off any dust or lint.
Cleaning and maintenance
Page 58
58-ENGLISH
Specifications
Power supply: 100 V - 240 V ~, 50 Hz/60 Hz
Power consumption: 220 W [During standby (when fan is
stopped): Approx. 6 W]
Amps: 2.5 A - 1.0 A
LCD panel:
Panel size (diagonal): 0.7 type (17.78 mm)
Aspect ratio: 4:3
Micro lens array: Available
Display method: 3 transparent LCD panels (RGB)
Drive method: Active matrix method
Pixels:
PT-LB10NTE/PT-LB10E/PT-LB10VE:
786 432 (1 024 x 768) x 3 panels
PT-LB10SE: 480 000 (800 x 600) x 3 panels
Lens: Manual zoom (1 - 1.2) / Manual focus
PT-LB10NTE/PT-LB10E/PT-LB10SE
: F 1.7 - 1.9 f 21.5 mm - 25.8 mm
PT-LB10VE: F 2.0 - 2.3 f 22.0 mm - 26.2 mm
Lamp: UHM lamp (155 W)
Luminosity:
PT-LB10NTE/PT-LB10E/PT-LB10SE
: 2 000 lm
PT-LB10VE: 1 600 lm
Scanning frequency (for RGB signals):
Horizontal scanning frequency: 15 kHz - 91 kHz
Vertical scanning frequency: 50 Hz - 85 Hz
Dot clock frequency: Less than 100 MHz
YPBPR signals: 480i, 576i, 480p, 576p, 1 080/60i,
1 080/50i, 720/60p
Colour system: 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/
PAL60/SECAM)
Projection size: 838.2 mm - 7 620 mm (33˝ - 300˝)
Throw distance:
PT-LB10NTE/PT-LB10E/PT-LB10SE
: 1.1 m - 10.7 m (3´7˝ - 35´1˝)
PT-LB10VE: 1.1 m - 11.0 m (3´7˝ - 36´1˝)
Optical axis shift: 6:1 (fixed)
Screen aspect ratio: 4:3
Installation: Front/Rear/Ceiling/Desk (menu selection)
Speaker: 4 cm x 3 cm oval x 1
Max. useable volume output: 1 W (mono)
Connectors
RGB IN/OUT: Dual line, one for input and one for output.
D-sub HD 15-pin (female)
During YPBPR input/output:
Y: 1.0 V [p-p] (Including sync), 75 Ω
P
B, PR : 0.7 V [p-p], 75 Ω
Page 59
ENGLISH-59
Others
During RGB input/output:
R.G.B.: 0.7 V [p-p], 75 Ω
G.SYNC: 1.0 V [p-p], 75 Ω
HD/SYNC: TTL, automatic positive/negative polarity
compatible
VD: TTL, automatic positive/negative polarity
compatible
VIDEO IN: Single-line, RCA pin jack
1.0 V [p-p], 75 Ω
S-VIDEO IN: Single-line, Mini DIN 4-pin
Y 1.0 V [p-p], C 0.286 V [p-p], 75 Ω
AUDIO IN: Single-line, RCA pin jack x 2 (L-R)
0.5 V [rms]
SERIAL: DIN 8-pin RS-232C compatible
Cabinet: Moulded plastic (PC/ABS)
Dimensions:
Width: 297 mm (11-11/16˝)
Height: 73 mm (2-27/32˝)
Length: 210 mm (8-1/4˝)
Weight:
PT-LB10NTE: 2.2 kg (4.9 lbs.)
PT-LB10E/PT-LB10VE/PT-LB10SE
: 2.1 kg (4.6 lbs.)
Operating environment:
Temperature: 0 °C - 40 °C (32 °F - 104 °F)
[When the “FAN CONTROL” is set to
“HIGH”
(page 45): 0 °C - 35 °C (32 °F - 95 °F)]
Humidity: 20% - 80% (no condensation)
Certifications: EN60950, EN55022, EN61000-3-2,
EN61000-3-3, EN55024
<Remote control unit>
Power supply: 3 V DC (Lithium CR2025 battery x1)
Operating range: Approx. 7 m (23´) (when operated directly
in front of signal receptor)
Weight: 18 g (0.6 ozs.) (including battery)
Dimensions:
Width: 40 mm (1-9/16˝)
Length: 6.5 mm (-1/4˝)
Height: 86 mm (3-3/8˝)
<Options>
Ceiling bracket ET-PKC80
Wireless remote control unit ET-RM300
Serial adapter ET-ADSER
(DIN 8-pin/D-sub 9-pin)
Wireless card ET-CDWL3E/ET-CDWL2E
ET-CDWL3ES/ET-CDWL2ES (for Spain)
ET-CDWL3SG/ET-CDWL2SG(for Singapore
)
ET-CDWL3U/ET-CDWL2U (for Malaysia)
Page 60
60-ENGLISH
Appendix
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2 The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture
is projected.
B Some loss of data occurs to make projection easier.
*3 Signals with “OK” in the “Resizing” column can be set using the
“RESIZING” command in the “POSITION” menu. (page 42)
*4 Signals that are compatible with the “FRAME LOCK” function. (page 42)
List of compatible signals
720 x 480i 15.7 59.9 A A OK OK
Video/S-Video
720 x 576i 15.6 50.0 A A OK OK
Video/S-Video
720 x 480i 15.7 59.9 13.5 A A OK OK
YPBPR/RGB
720 x 576i 15.6 50.0 13.5 A A OK OK
YPBPR/RGB
720 x 483 31.5 59.9 27.0 A A OK OK
YPBPR/RGB
720 x 576 31.3 50.0 27.0 A A OK OK
YPBPR/RGB
1 920 x 1 080i
33.8 60.0 74.3 A A
YPBPR/RGB
1 920 x 1 080i
28.1 50.0 74.3 A A
YPBPR/RGB
1 280 x 720
45.0 60.0 74.3 A A
YPBPR/RGB
640 x 400 31.5 70.1 25.2 A A OK OK RGB
640 x 400 37.9 85.1 31.5 A A OK OK RGB
640 x 480 31.5 59.9 25.2 A A OK OK RGB
640 x 480 35.0 66.7 30.2 A A OK OK RGB
640 x 480 37.9 72.8 31.5 A A OK OK RGB
640 x 480 37.5 75.0 31.5 A A OK OK RGB
640 x 480 43.3 85.0 36.0 A A OK OK RGB
800 x 600 35.2 56.3 36.0 A AA OK RGB
800 x 600 37.9 60.3 40.0 A AA OK RGB
800 x 600 48.1 72.2 50.0 A AA OK RGB
800 x 600 46.9 75.0 49.5 A AA OK RGB
800 x 600 53.7 85.1 56.3 A AA OK RGB
832 x 624 49.7 74.6 57.3 A A OK RGB
1 024 x 768
48.4 60.0 65.0 AA A RGB
1 024 x 768
56.5 70.1 75.0 AA A RGB
1 024 x 768
60.0 75.0 78.8 AA A RGB
1 024 x 768
68.7 85.0 94.5 AA A RGB
1 024 x 768i
35.5 87.0 44.9 AA A RGB
1 152 x 864
64.0 71.2 94.2 A A RGB
1 152 x 864
67.5 74.9 108.0 B B RGB
1 152 x 864
76.7 85.0 121.5 B B RGB
1 152 x 870
68.7 75.1 100.0 B B RGB
1 280 x 960
60.0 60.0 108.0 B B RGB
1 280 x 1 024
64.0 60.0 108.0 B B RGB
1 280 x 1 024
80.0 75.0 135.0 B B RGB
1 280 x 1 024
91.1 85.0 157.5 B B RGB
1 400 x 1 050
64.0 60.0 108.0 B B RGB
1 600 x 1 200
75.0 60.0 162.0 B B RGB
Display
resolution
(dots)*
1
Scanning
frequency
H
(kHz)V (Hz)
Dot clock
frequency
(MHz)
Picture
quality*
2
LB10NTE
LB10E
LB10VE
LB10SE
LB10NTE
LB10E
LB10VE
LB10SE
Resizing*
3
NTSC/NTSC4.43/
PAL-M/PAL60
PAL/PAL-N/SECAM
480i
576i
480p
576p
1 080/60i
1 080/50i
720/60p
VGA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21
MSXGA
SXGA
UXGA
Format
Mode
*
4
*
4
*
4
*
4
*
4
*
4
*
4
Page 61
Others
Pin assignments
Pin No. Signal
#
Earth (Luminance signal)
Earth (Colour signal)
Luminance signal
Colour signal
$
%
&
Pin No. Signal
#
R/PR
G/G·SYNC/Y
B/PB
SDA
$
%
.
/
HD/SYNC
0
VD
1
SCL
Pin & and + are spare.
Pins '-*, , and - are for earth.
Pins . and 1 functions are only valid when supported by the computer.
#$
&%
S-VIDEO IN
Appearance
-1
#'
,(
RGB IN/RGB OUT
Appearance
Projection dimensions calculation methods
If the screen size (diagonal) is SD (m), then the following formula is used to
calculate the projection distance for the wide lens position (LW) and the
projection distance for the telephoto lens position (LT).
*The values obtained from the formulas above are approximate.
For 16:9 aspect ratios, the following formula can be used to calculate the
projection distance.
PT-LB10NTE/PT-LB10E/PT-LB10SE
PT-LB10VE
LW=0.030xSD/0.0254-0.037 LW=0.031xSD/0.0254-0.038
LT=0.036xSD/0.0254-0.037 LT=0.037xSD/0.0254-0.038
PT-LB10NTE/PT-LB10E/PT-LB10SE
PT-LB10VE
LW=0.032xSD/0.0254-0.037 LW=0.033xSD/0.0254-0.038
LT=0.039xSD/0.0254-0.037 LT=0.040xSD/0.0254-0.038
ENGLISH-61
SD
SW
4:3
LW/LT
H1
SH
Page 62
62-ENGLISH
Using the SERIAL connector
The serial connector which is on the connector panel of the projector
conforms to the RS-232C interface specification, so that the projector can be
controlled by a personal computer which is connected to this connector.
Connection
Pin assignments and signal
names
Basic format
The data sent from the computer to
the projector is transmitted in the
format shown below.
Pin
No.
Communications settings
Signal
name
Contents
1
2
6
8
53
%
RXD Received data
&
GND Earth
'
TXD Transmitted data
#
$
Connected internally
(
)
*
DIN 8-pin
Appearance
Signal level RS-232C
AsynchronousSync. method
Baud rate
Parity
9 600 bps
None
Character length 8 bits
Stop bit 1 bit
X parameter None
S parameter None
STX Command:Parameter ETX
Start byte
(02h)
3 bytes
1 byte
1 byte-5 bytes
End byte
(03h)
DIN 8-pin (male)
Serial adapter
(ET-ADSER : sold
separately)
SERIAL(female)
Computer
NOTE:
B The projector can not receive
the command for 10 seconds
after the lamp is switched on.
Wait 10 seconds before sending
the command.
B If sending multiple commands,
check that a response has been
received from the projector for
one command before sending
the next command.
B When a command which does
not require parameters is sent,
the colon (:) is not required.
B If an incorrect command is sent
from the personal computer, the
“ER401” command will be sent
from the projector to the
personal computer.
NC
NC
You must use only RS-232C Serial
Interface Cable with ferrite core,
type ET-ADSER.
Page 63
ENGLISH-63
Others
Control commands
The commands which the personal computer can use to control the projector
are shown in the following table.
Command
Control
Contents
Remarks
In standby mode, all commands other than
the PON command are ignored.
B The PON command is ignored during
lamp ON control.
B If a PON command is received while the
cooling fan is operating after the lamp
has switched off, the lamp is not turned
back on again straight away, in order to
protect the lamp.
Power ONPON
Power OFFPOF
VolumeAVL
Parameter
000-063 (Adjustment value 0-63)
Input signal
selection
IIS
Parameter
VID=VIDEO SVD=S-VIDEO
RG1=RGB (YPBPR)
NWP=NETWORK (PT-LB10NTE only)
Lamp ON
condition query
Q$S
Callback
0 = Standby
1 = Lamp ON control active
2 = Lamp ON
3 = Lamp OFF control active
Cable specifications
(When connected to a personal computer)
1
2
3
4
5
6
7
8
7
8
3
5
2
6
1
4
9
At the projector
At the computer
(DTE specifications)
Page 64
64-ENGLISH
These Operating Instructions are printed on recycled paper.
Trademark acknowledgements
B VGA and XGA are trademarks of International Business Machines
Corporation.
B Macintosh is a registered trademark of Apple Computer, Inc.
B S-VGA is a registered trademark of the Video Electronics Standards
Association.
All other trademarks are the property of the various trademark owners.
Dimensions
<Units: mm (inch)>
81.2(3-3/16)
297(11-11/16)
41.8(1-5/8)
7(-1/4)
73(2-27/32)
210(8-1/4)
196(7-11/16)
Loading...