Panasonic PT-EX620L User Manual

PEC
S
Product Number : PT-EX620
Product Name : LCD Projectors
ILE
F
SFD16M041
1/13
LCD Projector
Specications
Main unit
Power supply
Power consumption
BTU value
LCDpanel
Lens
Lamp
Screen size Brightness*
Center-to-corner uniformity* Contrast*
2
2
Resolution
Scanning frequency
Keystone correction range
Standby Mode (Eco)*1 0.5W, 0.3W (Taiwan) Standby Mode (Normal) 12W Standby Mode (Normal and Audio monitor out) 30W
Panel size Display method Drive method Pixels
HDMI/DIGITAL LINK RGB YP
Video/S-Video
2
BPR (YCBCR)
PT-
EX620
AC100 - 240V 5.3 - 2.1A 50Hz/60Hz 461W
Max 1,573 BTU
16.0 mm (0.63 in) diagonal (4:3 aspect ratio)
Transparent LCD panel (× 3, R/G/B)
Active matrix 786,432 (1,024 × 768) × 3, total of 2,359,296 pixels Powered zoom (throw ratio 1.32-2.44:1), powered focus, F 1.6-2.2, f 17.1-31.7 mm
320 W UHM lamp
Lamp replacement cycle 4,000 hours (lamp power: Normal), 5,000 hours (lamp power: Eco) This is the maximum value when the lamp is turned on for 2 hours and off for 0.25 hours.
1.02–10.16 m (40–400 inches) (4:3 aspect ratio) 6,200 lumens
(Lamp power: Normal, Dynamic mode, Iris off, Daylight View:off, Auto Power Save:off)
90% 10,000:1
(Lamp power: Normal, Dynamic mode, Iris on, Daylight View:off, Auto Power Save:off)
1,024 × 768 pixels
fH: 15- 90kHz, fV: 24 - 100Hz, dot clock: 25 - 162 MHz
fH: 15- 90kHz, fV: 24 - 100Hz, dot clock: 162 MHz or lower 525i (480i): f 625i (576i): f 525p (480p): f 625p (576p): f 750 (720)/60p: f 750 (720)/50p: f 1125 (1080)/60i: f 1125 (1080)/50i: f 1125 (1080)/25p: f 1125 (1080)/24p: f 1125 (1080)/24sF: f 1125 (1080)/30p: f 1125 (1080)/60p: f 1125 (1080)/50p: f f
H: 15.75 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60] H: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
f
Only [KEYSTONE] used
Vertical
keystone
correction
angle α (°)
±35 ±35 ±35±35 0.80.9 0.80.9
* Supplied lens
Horizontal
keystone
correction
angle β (°)
Vertical
keystone
correction
angle α (°)
H15.73 kHz; fV59.94 Hz, H15.63 kHz; fV50 Hz,
H
31.47 kHz; fV60 Hz,
H31.25 kHz; fV50 Hz, H45.00 kHz; fV60 Hz, H37.50 kHz; fV50 Hz, H33.75 kHz; fV60 Hz, H28.13 kHz; fV50 Hz, H28.13 kHz; fV25 Hz, H27.00 kHz; fV24 Hz, H27.00 kHz; fV48 Hz, H33.75 kHz; fV30 Hz, H67.50 kHz; fV60 Hz, H56.25 kHz; fV50 Hz
[KEYSTONE] and [CURVED] used together Only [CURVED] used
Horizontal
keystone
correction
angle β (°)
Min. value
of R2/L2
Min. value
of R3/L3
Min. value
of R2/L2
Min. value
of R3/L3
[VERTICAL KEYSTONE] (viewed from the side) [HORIZONTAL KEYSTONE] (viewed from above)
Screen
Screen
As of March 2016 2/13
SFD16M041
LCD Projector
PT-
EX620
Keystone correction range
Vertical arc correction (viewed from the side) Horizontal arc correction (viewed from above)
Projection distance Arc radius
Screen
Arc center
Screen
Projection distance Arc radius
• When [Curved screen correction] is used, the focus of the entire screen may be lost as correction increases.
• Make the curved screen a circular arc shape with one part of a perfect circle removed.
Screen
Arc center
Screen
Optical axis shift Vertical: ±50% (powered) Horizontal: ±30% (powered) Installation Ceiling/oor, front/rear Speaker 4.0 cm (1-9/16 in) (monaural) × 1 Terminals
HDMI IN 1/HDMI IN 2 HDMI 19-pin ×2, Deep Color, compatible with HDCP,
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz) DIGITAL LINK IN RJ-45 x 1 (HDBaseT™ compatible), Deep Color, compatible with HDCP,
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz) RGB 1 IN BNC × 5 R,G,B:
0.7 Vp-p, 75 ohms, (G: 1.0 Vp-p, 75 ohms for sync on G) HD/VD, SYNC: TTL, high impedance, positive/negative automatic
P Y/C
Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal),
BPR(CBCR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms RGB 2 IN D-sub HD 15-pin (female) × 1 R,G,B:
0.7 Vp-p, 75 ohms, (G: 1.0 Vp-p, 75 ohms for sync on G) HD/VD, SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
P
Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal),
BPR(CBCR
): 0.7 Vp-p, 75 ohms VIDEO IN Pin jack × 1, 1.0 Vp-p, 75 ohms MONITOR OUT D-sub HD 15-pin (female) × 1 R,G,B:
0.7 Vp-p, 75 ohms, (G: 1.0 Vp-p, 75 ohms for sync on G) HD/VD, SYNC: TTL, high impedance, positive/negative automatic
Y, PB, PR
Y: 1.0 Vp-p (including sync signal), PBPR: 0.7 Vp-p, 75 ohms AUDIO IN 1/AUDIO IN 2 M3 × 2, 0.5 Vrms, input impedance: 22 kilohms or more AUDIO IN 3 Pin jack(L, R) × 1, 0.5 Vrms, input impedance: 22 kilohms or more VARIABLE AUDIO OUT M3 × 1 (monitor out, stereo) 0–2.0 Vrms, variable, output impedance: 2.2 kilohms or less SERIAL IN D-sub 9 p × 1, for external control (RS-232C compliant) REMOTE 1 IN D-sub 9-pin (female) ×1, for external control (parallel) REMOTE 2 IN M3 jack × 1 for wired remote control LAN RJ-45 x 1 for network connection 10Base-T/100Base-TX, compatible with Art-Net, PJLink™(Class 1) WIRELESS USB Type A × 1, for wireless projection with optional dongle (ET-WML100) DC OUT USB Type A × 1, for power supply (DC5 V, max 900 mA)
Projection distance Arc radius
Projection distance Arc radius
As of March 2016 3/13
SFD16M041
LCD Projector
PT-
EX620
Power cord length Cabinet materials Dimensions (W × H × D)
3.0 m (9 ft10 in) Molded plastic 498 x 145*
3
x 398.3mm
(19-19/32 x 5-11/16*
4
Weight* Operation noise Operating environment
Operating temperature Operating humidity
Approx. 8.4kg (18.5lbs) 29 dB (Silent), 35 dB (Normal/Eco) 0–45 °C (32–113 °F)* 20%–80% (no condensation)
Remote control unit
Power supply Operation range*
6
3 V DC (R03/LR03/AAAtypebattery × 2) Approx. 30 m (98 ft5 in) when operated from directly in front of the
signal receptor
Dimensions (W × H × D) Weight
48 × 145 × 27 mm (1-7/8 × 5-23/32 × 1-1/16inches) Approx. 102 g (3.6 oz) (including batteries)
Supplied accessories
Power cord (including power cord holder)(× 1) Wireless/wireled remote control unit (× 1) Batteries for remote control (AAA/R03/LR03 type× 2) Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring &
Control Software) (× 1) Lens cap (× 1)
Optional accessories
Zoom lens Ceiling mount bracket
ET-ELT30, ET-ELT31, ET-ELW30, ET-ELW31 ET-PKD120H (for high ceilings)
ET-PKD120S (for low ceilings) Bracket assembly Replacement lamp unit Replacement filter unit
ET-PKE300B (for ET-PKD120H/PKD120S)
ET-LAEF100
ET-RFE300 Early Warning Software ET-SWA100series Digital Interface Box ET-YFB100G DIGITAL LINK Switcher ET-YFB200G Wireless module ET-WML100
3
x 15-11/16 in ) with supplied lens
5
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
*
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal. Only Taiwan model, 0.15 W.
2 Measurement, measuring conditions, and method of notation all comply with
*
legs at shortest position.
3 With
*
4 Average value. May differ depending on models.
*
5 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when used at altitudes between 1,400 m and 2,700 m (4,593 ft to 8,858 ft) above
*
sea level. When operating temperature exceeds 40 °C (35 °C at high altitude), lamp power may automatically switch to ECO in order to protect the projector.
6 Operation range differs depending on environments.
*
ISO/IEC 21118:2012 international standards.
As of March 2016 4/13
SFD16M041
Loading...
+ 9 hidden pages