• 3-chip DLP™ image quality from compact and lightweight body
• 6000 lumens and 1000:1 contrast ratio
• BriteOptic™ Dual Lamp system with UHM™ lamps
• Dust-free construction
•True SXGA (1280 x 1024) resolution
• Digital Cinema Reality™ and high-speed DSP chips
• Built-in multi-screen processor, colour matching and edge blending
• Network function (remote control/e-mail)
• Easy installation and maintenance
- 1 -
S P E C F I L E
PRODUCT NO.: PT-D7600
PRODUCT NAME: DLP™-Based Projector
MAJOR FEATURES
2
PT-D7600
DLP™-Based Projector
S P E C F I L E
Specifications
Main Unit
Power supply: 220–240 V AC, 50/60 Hz
Power consumption: 800 W (800 VA) (12 W during standby mode with fan stopped)
DMD™ device: Panel size: 0.9˝ diagonal (5:4 aspect ratio)
Display method: DMD™ (x 3, R/G/B), DLP™ system
Pixels: 1,310,720 (1,280 x 1,024) x 3, total of 3,932,160 pixels
Lens: Optional powered zoom/focus lenses
Lamp: 300 W UHM™ lamps (x 2) (BriteOptic™ Dual Lamp System)
Screen size: 70–600 inches (1,778–15,240 mm) diagonally (5:4 aspect ratio)
*70–300 inches (1,778–7,620 mm) diagonally (5:4 aspect
ratio) with the ET-D75LE5
Brightness: 6,000 lumens (dual lamp, high power mode)
Centre-to-corner uniformity ratio: 90%
Contrast: 1,000:1 (full on/full off, high contrast mode, with a high-contrast lens)
(brightness: 4,500 lumens)
600:1 (full on/full off, normal contrast mode with a standard lens
Resolution: RGB: 1,280 x 1,024 pixels
(1,600 x 1,200 pixels compatible, compression mode)
Video: 560 TV lines
Scanning frequency: RGB: Horizontal: 15–100 kHz, Vertical: 24–120 Hz,
Dot clock: 20 –162 MHz
* Images may not be normally displayed when projecting moving pic-
tures with vertical frequency which is not between 45 Hz and 61 Hz.
YPBPR (YCB CR): 480i: fH 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
480p: fH
31.5 kHz; fV 60 Hz, 576p: f
H 31.25 kHz; fV 50 Hz,
720/60p: f
H 45 kHz; fV 60 Hz, 1035/60i: fH 33.75 kHz; fV 60 Hz,
1080/60i: fH 33.75 kHz; fV 60 Hz, 1080/50i: fH 28.13 kHz; fV 50 Hz,
1080/25p: fH
28.13 kHz; fV
25 Hz, 1080/24p: fH 27 kHz; fV 24 Hz,
1080/24sF: f
H 27 kHz; fV 48 Hz, 1080/30p: fH 33.75 kHz; fV 30 Hz
S-Video/Video: Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(PAL, PAL60, PAL-M, PAL-N, SECAM, NTSC, NTSC4.43)
Optical axis shift: Horizontal and vertical (powered)
Keystone correction range: Vertical: ±40° (±22° with the ET-D75LE5)
Installation: Ceiling/desk, front/rear
Terminals: RGB1 IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 1.4 Vp-p–5.0Vp-p, 75Ω (positive/negative)
Y, PB, PR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
RGB2 IN/RGB1 OUT: D-sub HD 15-pin x 1, IN/OUT selection is operated with on-screen menu.
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 75Ω, TTL (positive/negative polarity)
Y, PB
, P
R: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
VIDEO IN: BNC x 1, 1.0 Vp-p, 75Ω
VIDEO OUT: BNC x 1, 1.0 Vp-p, 75Ω, active through
S-VIDEO IN: Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
SERIAL IN: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
SERIAL OUT: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
REMOTE 1 IN: M3 jack x 1 for wired remote control or link control
REMOTE 1 OUT: M3 jack x 1 for wired remote control or link control
REMOTE 2 IN: D-sub 9-pin x 1 for external control (parallel)
Optional board slot: x 1
ET-MD95RGB
RGB/YP
BPR IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD (H) / SYNC (H•V) • VD (V): 75Ω, TTL (positive/negative)
Y, PB, PR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω, BETACAM compatible
ET-MD95VM2
VIDEO BNC x 2 (IN, OUT)
VIDEO IN: 1.0 Vp-p, 75Ω or high impedance (auto selection)
VIDEO OUT: 1.0 Vp-p, 75Ω or high impedance (auto selection)
S-VIDEO IN: BNC x 2 (Y, C)
Y, C: Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
YC
BCRIN: (BNC x 3, common with VIDEO and S-VIDEO connectors)
Y, CB, CR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
As of April 2004
3
PT-D7600
DLP™-Based Projector
S P E C F I L E
Specifications (continued)
ET-MD95SD1
SERIAL IN: BNC x 1
4:2:2 digital serial component signal (480i/576i), SMPTE 259M compliant
SERIAL OUT: BNC x 1, active through
ET-MD95SD2
SERIAL IN: BNC x 2 (MAIN, SUB)
4:2:2 digital serial component signal (480i/576i), SMPTE 259M compliant
4:2:2 digital serial component signal (480p), SMPTE 294M compliant
4:2:0 digital serial component signal (480p), SMPTE 294M compliant
SERIAL OUT: BNC x 2 (MAIN,SUB), active through
ET-MD95SD3
HD SERIAL IN: BNC x 1
720p/1035i/1080i/1080-24p, SMPTE 292M compliant
HD SERIAL OUT: BNC x 1, active through
ET-MD75DV
DIV-D IN: DVI-D 24-pin x 1, DVI 1.0 compliant, VGA to SXGA compatible
DIV-D OUT: DVI-D 24-pin x 1, DVI 1.0 compliant, VGA to SXGA compatible
VGA: 640 x 480, SXGA: 1280 x 1024
ET-MD75NT
LAN: RJ-45 x 1, 10Base-T/100Base-TX, for network
SERIAL: D-sub 9-pin (male) x 1, for service
Power cord length: 2.5 m
Cabinet material: ABS/PC
Dimensions (W x H x D): 530 x 200 x 569 mm (without projection lens)
Weight: 19.8 kg (without projection lens)
Operating environment: Temperature: 0° – 40°C (32°–104°F), 0°– 35°C (32°–95°F)
Humidity: 10%– 80% (no condensation)
Safety regulation: EN 60950, IEC 60950, EN 55022-B, EN55024, EN 61000-3-2, EN 61000-
3-3, C-Tick, MIC
Remote Control Unit
Number of keys: 32 keys, 42 functions
Power supply: 3 V DC (AA-size battery x 2)
Operation range: Wireless: approx. 7 m when operated from directly in front of the signal
receptor), wired: approx. 15 m
Dimensions (W x H x D): 50 x 31 x 181 mm
Weight: Approx. 110 g (including batteries)
Supplied accessories: Power cord, Wireless/wired remote control unit, Remote control cable
(15 m), Batteries for remote control (x 2)
As of April 2004
Optional accessories
:
Replacement lamp unit: ET-LAD7500 (1 unit)
ET-LAD7500W (set of two
lamps)
Ceiling mount bracket: ET-PKD75 (for high ceilings)
ET-PKD75S (for low ceilings)
Dual stacking mount bracket: ET-DFD75
Carrying handle: ET-HAD75
Zoom lens (1.5–2.0:1): ET-D75LE1
Zoom lens (2.0–3.0:1): ET-D75LE2
Zoom lens (3.0–5.0:1): ET-D75LE3
Zoom lens (5.0–8.0:1): ET-D75LE4
Fixed-focus lens (0.8:1): ET-D75LE5
Super-contrast zoom lens (1.5–2.0:1):
ET-D75LE1SC
Super-contrast zoom lens (2.0–3.0:1):
ET-D75LE2SC
Super-contrast zoom lens (3.0–5.0:1):
ET-D75LE3SC
Super-contrast zoom lens (5.0–8.0:1):
ET-D75LE4SC
DVI board: ET-MD75DV
Network board: ET-MD75NT
Video/S-Video input board: ET-MD95VM2
SDI (480i/576i) input board: ET-MD95SD1
SDI (480i/576i/480p) input board:
ET-MD95SD2
SDI (720p/1035i/1080i/1080-24p) input board:
ET-MD95SD3
RGB/YP
BPR: ET-MD95RGB
DVI cable: ET-SCDV03
Wireless remote receiver: ET-RMRC1
Weights and dimensions shown are approximate. Specifications subject to change without notice.
4
PT-D7600
DLP™-Based Projector
S P E C F I L E
As of April 2004
Dimensions
unit: mm
Note: This illustration is not drawn to scale.
Terminals
RGB IN connector pin assignment
1 Remote 1 input/output
2 Remote 2 input/output
3 Serial input/output
4 S-Video input
5 Video input/output
6 RGB 1 input
7 RGB 2 input/RGB 1 output
8 Optional board slot
no. signal
6 GND
7 GND
8 GND
9NC
10 GND
no. signal
11 NC
12 SDA*
13 HD/SYNC
14 VD
15 SCL*
no. signal
1 R/PR
2 G/Y
3 B/PB
4 GND
5 GND
* Effective when connected to a PC having proper functions.
1223
4 5678
5
PT-D7600
DLP™-Based Projector
S P E C F I L E
As of April 2004
Standard setting-up positions
Screen aspec ratio 5:4
L
H
H
L
L
unit: mm
Note: This illustration is not drawn to scale.
Note: Values shown are approximate. Accuracy of values is ±5%.
When keystone correction is performed, the screen size becomes smaller.
The projector with optional ceiling
mount bracket ET-PKD75 and
zoom lens ET-D75LE1.
The projector with optional ceiling
mount bracket ET-PKD75 and
zoom lens ET-D75LE1.
The projector with optional zoom
lens ET-D75LE1.
Projection distance (L)
Screen
size
(inch,
diagonal)
ET-75LE1/ ET-D75LE2/
min. max. min. max. min. max. min. max.
70
2 168 2 891 2 925 4 409 4 421 7 405 7 412 11 966 1 131
80
2 489 3 318 3 355 5 054 5 066 8 480 8 487 13 691 1 293
90
2 809 3 745 3 784 5 699 5 711 9 555 9 562 15 415 1 455
100
120
150
200
250
300
400
500
600
3 130 4 173 4 213 6 345 6 356 10 631 10 638 17 139 1 618
3 771 5 027 5 071 7 635 7 647 12 781 12 788 20 587 1 942
4 732 6 309 6 359 9 570 9 582 16 007 16 014 25 760 2 428
6 335 8 446 8 505 12 796 12 808 21 383 21 390 34 380 3 238
7 937 10 583 10 651 16 022 16 034 26 760 26 767 43 001 4 049
9 540 12 720 12 797 19 248 19 259 32 136 32 143 51 622 4 859
12 745 16 993 17 088 25 699 25 711 42 889 42 896 68 863
15 950 21 267 21 380 32 151 32 163 53 642 53 648 86 104
19 155 25 540 25 672 38 603 38 614 64 394 64 401 103 346
D75LE2SCD75LE1SC
Zoom lens Fixed focus
ET-D75LE3/
D75LE3SC
ET-D75LE4/
D75LE4SC
lens
ET-D75LE5
Height from edge of projected image
to the center of lens (H)
Zoom lens
0–1 111
0–1 269
0–1 428
0–1 587
0–1 904
0–2 380
0–3 173
0–3 967
0–4 760
0–6 347
0–7 934
0–9 520
Fixed focus
lens
556
635
714
794
952
1 190
1 587
1 984
2 380
6
PT-D7600
DLP™-Based Projector
S P E C F I L E
As of April 2004
Calculation of the projection distance:
For a screen size, use the equation below to calculate the projection distance. (unit: mm)
ET-D75LE1/D75LE1SC
ET-D75LE2/D75LE2SC
ET-D75LE3/D75LE3SC
ET-D75LE4/D75LE4SC
ET-D75LE5
5 : 4 minimum L (m) = (diagonal screen size in inches) x 32.051 - 76
maximum L (m) = (diagonal screen size in inches) x 42.735 - 100
16 : 9 minimum L (m) = (diagonal screen size in inches) x 35.774 - 76
maximum L (m) = (diagonal screen size in inches) x 47.699 - 100
4 : 3 minimum L (m) = (diagonal screen size in inches) x 32.820 - 76
maximum L (m) = (diagonal screen size in inches) x 43.366 - 100
5 : 4 minimum L (m) = (diagonal screen size in inches) x 42.918 - 79
maximum L (m) = (diagonal screen size in inches) x 64.516 - 106
16 : 9 minimum L (m) = (diagonal screen size in inches) x 47.904 - 79
maximum L (m) = (diagonal screen size in inches) x 72.010 - 106
4 : 3 minimum L (m) = (diagonal screen size in inches) x 43.943 - 79
maximum L (m) = (diagonal screen size in inches) x 66.064 - 106
5 : 4 minimum L (m) = (diagonal screen size in inches) x 64.516 - 96
maximum L (m) = (diagonal screen size in inches) x 107.527 - 121
16 : 9 minimum L (m) = (diagonal screen size in inches) x 72.010 - 96
maximum L (m) = (diagonal screen size in inches) x 120.017 - 121
4 : 3 minimum L (m) = (diagonal screen size in inches) x 66.064 - 96
maximum L (m) = (diagonal screen size in inches) x 110.108 - 121
5 : 4 minimum L (m) = (diagonal screen size in inches) x 107.527 - 116
maximum L (m) = (diagonal screen size in inches) x 172.138 - 102
16 : 9 minimum L (m) = (diagonal screen size in inches) x 120.017 - 116
maximum L (m) = (diagonal screen size in inches) x 192.442 - 102
4 : 3 minimum L (m) = (diagonal screen size in inches) x 110.108 - 116
maximum L (m) = (diagonal screen size in inches) x 176.269 - 102
5 : 4 (fixed focus) L (m) = (diagonal screen size in inches) x 16.207 - 3
16 : 9 (fixed focus) L (m) = (diagonal screen size in inches) x 18.090 - 3
4 : 3 (fixed focus) L (m) = (diagonal screen size in inches) x 16.600 - 3
Screen aspec ratio 16:9
Note: Values shown are approximate. Accuracy of values is ±5%.
When keystone correction is performed, the screen size becomes smaller.
Projection distance (L)
Screen
size
(inch,
diagonal)
65
110
150
200
300
400
500
550
ET-D75LE1/
D75LE1SC
2 249 3 000 3 034 4 574 4 585 7 680 7 686 12 407 1 173 -342 – 1 151 404
3 859 5 147 5 190 7 815 7 825 13 080 13 086 21 067 1 987 -578 – 1 948 685
5 290 7 055 7 106 10 695 10 706 17 881 17 887 28 764 2 710 -789 – 2 657
7 079 9 440 9 501 14 296 14 306 23 882 23 888 38 386 3 615 -1 052 – 3 542
10 656 14 209 14 292 21 497 21 507 35 884 35 890 57 630 5 424 -1 577 – 5 313
14 234 18 979 19 082 28 698 28 708 47 886 47 891 76 875 -2 103 – 7 084
17 811 23 749 23 873 35 899 35 909 59 887 59 893 96 119 -2 629 – 8 855
19 600 26 134 26 268 39 499 39 510 65 888 65 894 105 741 -2 892 – 9 741
ET-D75LE2/
D75LE2SC
Zoom lens Fixed focus
ET-D75LE3/
D75LE3SC
Height from edge of projected image
to the center of lens (H)
lens
ET-D75LE4/
D75LE4SC
ET-D75LE5
Zoom lens Fixed focus
lens
934
1 245
1 867
7
PT-D7600
DLP™-Based Projector
S P E C F I L E
As of April 2004
Optical shift range
Floor mount
Ceiling mount
Loading...