Page 1
• 3-chip DLP™ image quality from compact and lightweight body
• 5000 lumens and 1000:1 contrast ratio
• BriteOptic™ Dual Lamp system with UHM™ lamps
• Dust-free construction
•True XGA (1024 x 768) resolution
• Digital Cinema Reality™ and high-speed DSP chips
• Built-in multi-screen processor, colour matching and edge blending
• Network function (remote control/e-mail)
• Easy installation and maintenance
- 1 -
S P E C F I L E
PRODUCT NO.: PT-D7500
PRODUCT NAME: DLP™-Based Projector
MAJOR FEATURES
Page 2
2
PT-D7500
DLP™-Based Projector
S P E C F I L E
Specifications
Main Unit
Power supply: 220–240 V AC, 50/60 Hz
Power consumption: 800 W (800 VA) (12 W during standby mode with fan stopped)
DMD™ device: Panel size: 0.7˝ diagonal (4:3 aspect ratio)
Display method: DMD™ (x 3, R/G/B), DLP™ system
Pixels: 786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Lens: Optional powered zoom/focus lenses
Lamp: 300 W UHM™ lamps (x 2) (BriteOptic™ Dual Lamp System)
Screen size: 70–600 inches (1,778–15,240 mm) diagonally (4:3 aspect ratio)
*70–300 inches (1,778–7,620 mm) diagonally (4:3 aspect
ratio) with the ET-D75LE5
Brightness: 5,000 lumens (dual lamp, high power mode)
Centre-to-corner uniformity ratio: 90%
Contrast: 1,000:1 (full on/full off, high contrast mode, with a high-contrast lens)
(brightness: 3,500 lumens)
600:1 (full on/full off, normal contrast mode with a standard lens
Resolution: RGB: 1,024 x 768 pixels
(1,600 x 1,200 pixels compatible, compression mode)
Video: 560 TV lines
Scanning frequency: RGB: Horizontal: 15–100 kHz, Vertical: 24–120 Hz,
Dot clock: 20 –162 MHz
* Images may not be normally displayed when projecting moving pic-
tures with vertical frequency which is not between 45 Hz and 61 Hz.
YPBPR (YCB CR): 480i: fH 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
480p: fH
31.5 kHz; fV 60 Hz, 576p: f
H 31.25 kHz; fV 50 Hz,
720/60p: f
H 45 kHz; fV 60 Hz, 1035/60i: fH 33.75 kHz; fV 60 Hz,
1080/60i: fH 33.75 kHz; fV 60 Hz, 1080/50i: fH 28.13 kHz; fV 50 Hz,
1080/25p: fH
28.13 kHz; fV
25 Hz, 1080/24p: fH 27 kHz; fV 24 Hz,
1080/24sF: f
H 27 kHz; fV 48 Hz, 1080/30p: fH 33.75 kHz; fV 30 Hz
S-Video/Video: Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(PAL, PAL60, PAL-M, PAL-N, SECAM, NTSC, NTSC4.43)
Optical axis shift: Horizontal and vertical (powered)
Keystone correction range: Vertical: ±40° (±27° with the ET-D75LE5)
Installation: Ceiling/desk, front/rear
Terminals: RGB1 IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 1.4 Vp-p–5.0Vp-p, 75Ω (positive/negative)
Y, PB, PR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
RGB2 IN/RGB1 OUT: D-sub HD 15-pin x 1, IN/OUT selection is operated with on-screen menu.
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 75Ω, TTL (positive/negative polarity)
Y, PB
, P
R: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
VIDEO IN: BNC x 1, 1.0 Vp-p, 75Ω
VIDEO OUT: BNC x 1, 1.0 Vp-p, 75Ω, active through
S-VIDEO IN: Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
SERIAL IN: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
SERIAL OUT: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
REMOTE 1 IN: M3 jack x 1 for wired remote control or link control
REMOTE 1 OUT: M3 jack x 1 for wired remote control or link control
REMOTE 2 IN: D-sub 9-pin x 1 for external control (parallel)
Optional board slot: x 1
ET-MD95RGB
RGB/YP
BPR IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD (H) / SYNC (H•V) • VD (V): 75Ω, TTL (positive/negative)
Y, PB, PR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω, BETACAM compatible
ET-MD95VM2
VIDEO BNC x 2 (IN, OUT)
VIDEO IN: 1.0 Vp-p, 75Ω or high impedance (auto selection)
VIDEO OUT: 1.0 Vp-p, 75Ω or high impedance (auto selection)
S-VIDEO IN: BNC x 2 (Y, C)
Y, C: Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
YC
BCRIN: (BNC x 3, common with VIDEO and S-VIDEO connectors)
Y, CB, CR: Y: 1.0 p-p, 75Ω, PB,/PR: 0.7 Vp-p, 75Ω
As of April 2004
Page 3
3
PT-D7500
DLP™-Based Projector
S P E C F I L E
Specifications (continued)
ET-MD95SD1
SERIAL IN: BNC x 1
4:2:2 digital serial component signal (480i/576i), SMPTE 259M compliant
SERIAL OUT: BNC x 1, active through
ET-MD95SD2
SERIAL IN: BNC x 2 (MAIN, SUB)
4:2:2 digital serial component signal (480i/576i), SMPTE 259M compliant
4:2:2 digital serial component signal (480p), SMPTE 294M compliant
4:2:0 digital serial component signal (480p), SMPTE 294M compliant
SERIAL OUT: BNC x 2 (MAIN,SUB), active through
ET-MD95SD3
HD SERIAL IN: BNC x 1
720p/1035i/1080i/1080-24p, SMPTE 292M compliant
HD SERIAL OUT: BNC x 1, active through
ET-MD75DV
DIV-D IN: DVI-D 24-pin x 1, DVI 1.0 compliant, VGA to SXGA compatible
DIV-D OUT: DVI-D 24-pin x 1, DVI 1.0 compliant, VGA to SXGA compatible
VGA: 640 x 480, SXGA: 1280 x 1024
ET-MD75NT
LAN: RJ-45 x 1, 10Base-T/100Base-TX, for network
SERIAL: D-sub 9-pin (male) x 1, for service
Power cord length: 2.5 m
Cabinet material: ABS/PC
Dimensions (W x H x D): 530 x 200 x 569 mm (without projection lens)
Weight: 19.8 kg (without projection lens)
Operating environment: Temperature: 0° – 40°C (32°–104°F), 0°– 35°C (32°–95°F)
Humidity: 10%– 80% (no condensation)
Safety regulation: EN 60950, IEC 60950, EN 55022-B, EN55024, EN 61000-3-2, EN 61000-
3-3, C-Tick, MIC
Remote Control Unit
Number of keys: 32 keys, 42 functions
Power supply: 3 V DC (AA-size battery x 2)
Operation range: Wireless: approx. 7 m when operated from directly in front of the signal
receptor), wired: approx. 15 m
Dimensions (W x H x D): 50 x 31 x 181 mm
Weight: Approx. 110 g (including batteries)
Supplied accessories: Power cord, Wireless/wired remote control unit, Remote control cable
(15 m), Batteries for remote control (x 2)
As of April 2004
Optional accessories
:
Replacement lamp unit: ET-LAD7500 (1 unit)
ET-LAD7500W (set of two
lamps)
Ceiling mount bracket: ET-PKK75 (for high ceilings)
ET-PKD75S (for low ceilings)
Dual stacking mount bracket: ET-DFD75
Carrying handle: ET-HAD75
Zoom lens (1.5–2.0:1): ET-D75LE1
Zoom lens (2.0–3.0:1): ET-D75LE2
Zoom lens (3.0–5.0:1): ET-D75LE3
Zoom lens (5.0–8.0:1): ET-D75LE4
Fixed-focus lens (0.8:1): ET-D75LE5
Super-contrast zoom lens (1.5–2.0:1):
ET-D75LE1SC
Super-contrast zoom lens (2.0–3.0:1):
ET-D75LE2SC
Super-contrast zoom lens (3.0–5.0:1):
ET-D75LE3SC
Super-contrast zoom lens (5.0–8.0:1):
ET-D75LE4SC
DVI board: ET-MD75DV
Network board: ET-MD75NT
Video/S-Video input board: ET-MD95VM2
SDI (480i/576i) input board: ET-MD95SD1
SDI (480i/576i/480p) input board:
ET-MD95SD2
SDI (720p/1035i/1080i/1080-24p) input board:
ET-MD95SD3
RGB/YP
BPR: ET-MD95RGB
DVI cable: ET-SCDV03
Wireless remote receiver: ET-RMRC1
Weights and dimensions shown are approximate. Specifications subject to change without notice.
Page 4
4
PT-D7500
DLP™-Based Projector
S P E C F I L E
As of April 2004
Dimensions
unit: mm
Note: This illustration is not drawn to scale.
Terminals
RGB IN connector pin assignment
1 Remote 1 input/output
2 Remote 2 input/output
3 Serial input/output
4 S-Video input
5 Video input/output
6 RGB 1 input
7 RGB 2 input/RGB 1 output
8 Optional board slot
no. signal
6 GND
7 GND
8 GND
9NC
10 GND
no. signal
11 NC
12 SDA*
13 HD/SYNC
14 VD
15 SCL*
no. signal
1 R/PR
2 G/Y
3 B/PB
4 GND
5 GND
* Effective when connected to a PC having proper functions.
1223
4 5678
Page 5
5
PT-D7500
DLP™-Based Projector
S P E C F I L E
As of April 2004
Standard setting-up positions
Screen aspec ratio 4:3
L
H
H
L
L
unit: mm
Note: This illustration is not drawn to scale.
Note: Values shown are approximate. Accuracy of values is ±5%.
When keystone correction is performed, the screen size becomes smaller.
The projector with optional ceiling
mount bracket ET-PKD75 and
zoom lens ET-D75LE1.
The projector with optional ceiling
mount bracket ET-PKD75 and
zoom lens ET-D75LE1.
The projector with optional zoom
lens ET-D75LE1.
Projection distance (L)
Screen
size
(inch,
diagonal)
ET-D75LE1/
D75LE1SC
min. max. min. max. min. max. min. max.
70
2 805 3 745 3 788 5 679 5 738 9 468 9 475 15 453 1 403 -213 – 1 280 533
80
3 217 4 295 4 341 6 505 6 571 10 838 10 845 17 675 1 615 -244 – 1 463 610
90
3 628 4 844 4 893 7 331 7 404 12 208 12 215 19 897 1 827 -274 – 1 646 686
100
120
150
200
250
300
400
500
600
4 040 5 394 5 446 8 158 8 238 13 578 13 585 22 119 2 040 -305 – 1 829
4 863 6 493 6 551 9 811 9 904 16 318 16 324 26 564 2 464 -366 – 2 195
6 097 8 141 8 208 12 290 12 404 20 427 20 434 33 231 3 101 -457 – 2 743
8 155 10 888 10 971 16 422 16 571 27 276 27 283 44 342 4 163 -610 – 3 658 1 524
10 213 13 635 13 733 20 555 20 738 34 126 34 133 55 453 5 224 -762 – 4 572 1 905
12 270 16 383 16 496 24 687 24 904 40 975 40 982 66 564 6 286 -914 – 5 486 2 286
16 385 21 877 22 020 32 951 33 238 54 674 54 680 88 786 -1 219 – 7 315
20 501 27 372 27 545 41 216 41 571 68 372 68 379 111 008 -1 524 – 9 144
24 616 32 866 33 070 49 480 49 904 82 071 82 078 13 3231 -1 829 – 10 973
ET-D75LE2/
D75LE2SC
Zoom lens Fixed focus
ET-D75LE3/
D75LE3SC
ET-D75LE4/
D75LE4SC
lens
ET-D75LE5
ET
Height from edge of projected image
to the center of lens (H)
Zoom lens
Fixed focus
lens
762
914
1 143
Page 6
6
PT-D7500
DLP™-Based Projector
S P E C F I L E
As of April 2004
Calculation of the projection distance:
For a screen size, use the equation below to calculate the projection distance. (unit: mm)
ET-D75LE1/D75LE1SC
ET-D75LE2/D75LE2SC
ET-D75LE3/D75LE3SC
ET-D75LE4/D75LE4SC
ET-D75LE5
4 : 3 minimum L (m) = (diagonal screen size in inches) x 41.152 - 76
maximum L (m) = (diagonal screen size in inches) x 43.366 - 100
16 : 9 minimum L (m) = (diagonal screen size in inches) x 44.834 - 76
maximum L (m) = (diagonal screen size in inches) x 59.861 - 100
4 : 3 minimum L (m) = (diagonal screen size in inches) x 55.249 - 79
maximum L (m) = (diagonal screen size in inches) x 66.064 - 106
16 : 9 minimum L (m) = (diagonal screen size in inches) x 60.192 - 79
maximum L (m) = (diagonal screen size in inches) x 90.790 - 106
4 : 3 minimum L (m) = (diagonal screen size in inches) x 83.333 - 96
maximum L (m) = (diagonal screen size in inches) x 110.108 - 120
16 : 9 minimum L (m) = (diagonal screen size in inches) x 90.790 - 96
maximum L (m) = (diagonal screen size in inches) x 149.243 - 120
4 : 3 minimum L (m) = (diagonal screen size in inches) x 136.986 - 115
maximum L (m) = (diagonal screen size in inches) x 222.222 - 102
16 : 9 minimum L (m) = (diagonal screen size in inches) x 149.243 - 115
maximum L (m) = (diagonal screen size in inches) x 242.106 - 102
4 : 3 (fixed focus) L (m) = (diagonal screen size in inches) x 21.231 - 84
16 : 9 (fixed focus) L (m) = (diagonal screen size in inches) x 23.131 - 84
Screen aspec ratio 16:9
Note: Values shown are approximate. Accuracy of values is ±5%.
When keystone correction is performed, the screen size becomes smaller.
Projection distance (L)
Screen
size
(inch,
diagonal)
ET-75LE1/ ET-D75LE2/
min. max. min. max. min. max. min. max.
65
2 838 3 791 3 833 5 746 5 805 9 581 9 586 15 635 1 420 -486 – 1 295 404
110
150
200
300
400
500
550
4 856 6 484 6 542 9 798 9 891 16 296 16 302 26 529 2 461 -822 – 2 192 685
6 649 8 879 8 949 13 400 13 522 22 266 22 272 36 214 3 386 -1 121 – 2 989 934
8 891 11 872 11 959 17 902 18 062 29 728 29 734 48 319 4 543 -1 494 – 3 985
13 374 17 858 17 978 26 906 27 141 44 653 44 658 72 529 6 856 -2 241 – 5 977
17 858 23 844 23 997 35 910 36 220 59 577 59 583 96 740 -2 989 – 7 970
22 341 29 830 30 017 44 914 45 299 74 501 74 507 120 951 -3 736 – 9 962
24 583 32 823 33 026 49 416 49 838 81 964 81 969 133 056 -4 109 – 10 958
D75LE2SCD75LE1SC
Zoom lens Fixed focus
ET-D75LE3/
D75LE3SC
Height from edge of projected image
to the center of lens (H)
lens
ET-D75LE4/
D75LE4SC
ET-D75LE5
Zoom lens Fixed focus
lens
1 245
1 867
Page 7
7
PT-D7500
DLP™-Based Projector
S P E C F I L E
As of April 2004
Floor mount
Ceiling mount
Optical shift range
Loading...