Panasonic PT-D5600UL User Manual

DLPTMBased Projector Commercial Use

Operating Instructions

Read these instructions completely before operating this unit.

TQBJ 0200

Model No. PT-D5600U

PT-D5600UL PT-DW5000U PT-DW5000UL

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP

based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required.

Model number: PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL

Serial number:

IMPORTANT SAFETY NOTICE

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the Product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: This equipment is equipped with a three-pin

grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.

WARNING

RISK OF ELECTRIC SHOCK. DO NOT OPEN

MISE EN GARDE-

RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.

WARNUNG-

ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GERÄT NICHT ÖFFNEN.

Do not remove

WARNING:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

–

Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded interface cables when

connecting to computer or peripheral devices. Any unauthorized changes or modifications to this equipment could void the user’s authority to operate.

NOTICE: This product has a High Intensity Discharge (HID) lamp that contains a small amount

of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>

Declaration of Conformity Model Number: PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL Trade Name: Panasonic Responsible Party: Panasonic North America

One Panasonic Way 4B-9, Secaucus, NJ 07094 Telephone Number: 1-800-524-1448 or 1-800-526-6610 Email: pjscservice@us.panasonic.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING:

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

Contents

IMPORTANT SAFETY NOTICE ..................................2

Precautions with regard to safety ............................5

Accessories ................................................................7

Precautions on handling ...........................................8

Name and function of parts.......................................9

Remote control ..................................................................9

Front and side of the projector ........................................11

Rear view of the main unit/Controls on rear panel ..........12

Side-mounted connection terminals ................................13

Using the remote control unit .................................14

Loading dry cells .............................................................14

Effective range of remote control operation ....................14

Setting projector ID number to remote control ................15

Using the remote control as a PC mouse........................15

Using a wired remote control...........................................16

Installation ................................................................16

Projection schemes .........................................................16

Installation geometry .......................................................16

Projection distances by projection lens ...........................17

Calculation formulas for projection distance by lens types

.......20

Connection ...............................................................21

Setup precautions ...........................................................21

Example of connecting with AV products ........................22

Example of connecting with PCs.....................................22

Projection..................................................................23

Powering up the projector ...............................................23

Making adjustment and selection ....................................23

Powering off the projector ...............................................24

Direct power off function..................................................24

How to install and remove the projection lens

(optional)...................................................................25

How to install the projection lens.....................................25

How to remove the projection lens ..................................25

How to adjust the lens .............................................25

How to adjust the lens focus, lens zoom and lens

up/down position movement (optical shift) ......................25

How to adjust the lens position to the left or right............25

Automatic adjustment (AUTO SETUP)...................26

Using the FREEZE function ....................................26

Using the SHUTTER function..................................26

Using the digital zoom (– D.ZOOM +) function......26

On-screen menus.....................................................27

Structure of menu screens ..............................................27

Basic menu operations....................................................28

Returning to the previous page .......................................28

Menu items shown in transparent characters..................28

Menu items setting ..........................................................28

Resetting to the factory default........................................28

Adjusting the picture ...............................................29

PICTURE MODE.............................................................29

BRIGHT...........................................................................29

CONTRAST.....................................................................29

COLOR............................................................................29

TINT ................................................................................29

COLOR TEMP. ...............................................................29

WHITE GAIN ...................................................................29

SHARPNESS ..................................................................29

NR ...................................................................................29

AI .....................................................................................30

TV-SYSTEM....................................................................30

SYSTEM..........................................................................30

Adjusting the position .............................................30

POSITION .......................................................................30

ASPECT ..........................................................................30

ZOOM..............................................................................31

CLOCK PHASE...............................................................31

KEYSTONE.....................................................................31

How to use ADVANCED MENU ...............................32

DIGITAL CINEMA REALITY ...........................................32

BLANKING ......................................................................32

INPUT RESOLUTION .....................................................32

CLAMP POS. ..................................................................32

RASTER POSITION........................................................33

XGA MODE .....................................................................33

SXGA MODE...................................................................33

Changing the display language ..............................33

OPTION1 settings.....................................................34

COLOR CORRECTION ..................................................34

CONTRAST MODE.........................................................34

AUTO SIGNAL ................................................................34

BACK COLOR.................................................................34

SUB MEMORY LIST .......................................................34

DVI EDID.........................................................................34

OPTION2 settings.....................................................35

ID.....................................................................................35

FRONT/REAR .................................................................35

DESK/CEILING ...............................................................35

LAMP SELECT................................................................35

LAMP POWER ................................................................35

RS232C...........................................................................36

SYSTEM INFORMATION ...............................................36

FAN CONTROL1.............................................................36

FAN CONTROL2.............................................................36

FUNC1 ............................................................................36

AUTO POW.OFF.............................................................36

PASSWORD ...................................................................36

Displaying the internal test pattern ........................37

Cycle of displayed internal test patterns..........................37

Setting the security..................................................37

Setting the password.......................................................37

Changing the password...................................................37

Setting the text ................................................................37

Changing the text ............................................................37

Setting the network..................................................38

Connecting the PC ...................................................38

System requirements ......................................................38

Connection example........................................................38

Using the serial terminals .......................................39

Examples of connection .................................................39

Pin assignments and signal names.................................39

Communication conditions (Factory setting) ...................39

Basic format ....................................................................39

Control commands ..........................................................40

Cable specifications ........................................................40

Using the Remote 2 terminal...................................40

Indication of lamp monitor ......................................41

Cleaning and replacement of air filter....................42

Procedure of cleaning .....................................................42

Replacing of lamp unit.............................................43

Timing of lamp unit replacement .....................................43

Lamp unit replacement steps ..........................................44

Using Web Browser Control ...................................46

Accessing from Web browser..........................................46

Password change page...................................................46

Basic control page...........................................................47

Detail control page ..........................................................47

Monitor information page.................................................48

Error information page.....................................................48

E-mail setup page ...........................................................49

DNS server setup page ...................................................51

POP server setup page ...................................................51

Ping test page .................................................................51

Contents of mail sent.......................................................52

Adjust clock page ............................................................52

Network config page........................................................53

Network status page........................................................53

Using the PJLinkTMprotocol ....................................54

Supported commands .....................................................54

PJLink

security authentication.......................................54

Before asking for service ........................................55

Specifications...........................................................56

Compatible Signal List ............................................58

Dimensions...............................................................59

Installation dimensions diagram ............................59

Français Information................................................60

Precautions with regard to safety WARNING

If a problem occurs (such as no image) or if you notice smoke or a strange smell coming from the projector, turn off the power and disconnect the power cord from the wall outlet.

• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.

• Check that no more smoke is coming out, and then contact an Authorized Service Center for repairs.

• Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to take the full weight of the projector.

• If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result.

• Installation work (such as ceiling suspension) should only be carried out by a qualified technician.

• If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.

• Continued use of the projector in this condition may result in fire or electric shocks.

• Contact an Authorized Service Center for repairs.

Do not cover the air filter, the air inlet and exhaust vents.

• Doing so may cause the projector to overheat, which can cause fire or damage to the projector.

Do not overload the wall outlet.

• If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

• High voltages which can cause fire or electric shocks are present inside the projector.

• For any inspection, adjustment and repair work, please contact an Authorized Service Center.

Use only the power cord supplied with the projector.

• Use only the supplied cord with three-pin plug and insert it only into a wall outlet that is connected to earth. Otherwise, electric shock could result.

Clean the power cord plug regularly to prevent it from becoming covered in dust.

• If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth.

• If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.

Do not do anything that might damage the power cord or the power cord plug.

• Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

• If the power cord is used while damaged, electric shocks, short-circuits or fire may result.

• Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

Do not handle the power cord plug with wet hands.

• Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

• If the plug is not inserted correctly, electric shocks or overheating could result.

• Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

Do not place the projector on top of surfaces which are unstable.

• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

• Failure to observe this may result in fire or electric shocks.

Do not disassemble the lamp unit.

• If the lamp section breaks, it may cause injury.

• The lamp unit has high internal pressure. If improperly handled, explosion might result.

• The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions

may result.

Precautions with regard to safety

Do not place liquid containers on top of the projector.

• If water spills onto the projector or gets inside it, fire or electric shocks could result.

• If any water gets inside the projector, contact an Authorized Service Center.

Do not insert any foreign objects into the projector.

• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks.

After removing the battery from remote control unit, keep it away from the reach of children.

• The battery can cause death by suffocation if swallowed.

• If the battery is swallowed, seek medical advice immediately.

Do not allow the + and - terminals of the battery to come into contact with metallic objects such as necklaces or hairpins.

• Failure to observe this may cause the battery to leak, overheat, explode or catch fire.

• Store the battery in a plastic bag and keep it away from metallic objects.

Before replacing the lamp unit, be absolutely sure to disconnect the power plug from the power outlet.

• Otherwise, electric shocks and/or damage may result.

When replacing the lamp, allow it to cool for at least one hour before handling it. Do not bring your hands or other objects close to the air outlet port.

• Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least 50 cm (16.7˝) of space], otherwise burns or damage could result.

Do not suspend the projector using only the hole used for the anti-theft clasp.

• The projector may fall or sustain damage, and possibly result in injury.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam.

• Using the projector under such conditions may result in fire or electric shocks.

When disconnecting the power cord, hold the plug, not the cord.

• If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

• Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.

Do not place objects or other projectors on top of this unit.

• The objects or projectors may lose their balance or fall off, causing possible injury. Further, stacking one projector directly on top of another may cause the projectors to become deformed, resulting in possible malfunctioning.

Do not short-circuit, heat or disassemble the battery or place it into water or fire.

• Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other injury may result.

When inserting the battery, make sure the polarities (+ and -) are correct.

• If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

• Do not use a new battery together with an old battery.

• Remove the batteries if you are not going to use the projector for a prolonged period of time.

Caution

Accessories

Check that all of the accessories shown below have been included with your projector.

Use only the Specified battery.

• If incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Do not look into the lens while the projector is being used.

• Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.

Do not place your skin into the light beam while the projector is being used.

• Strong light is emitted from the projector’s lens. If you place directly into this light, it can hurt or damage your skin.

Do not use the old lamp unit.

• The lamp section may break.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.

• Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces may cause injury.

• If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately.

• Ask your dealer to replace the lamp unit and check the inside of the projector.

Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Ask an Authorized Service Center to clean inside the projector at least once a year.

• If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.

• It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your

nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs.

Do not reach for the openings beside the optical lens, during horizontal or vertical movements of the lens there is a injury hazard.

Remote control unit [N2QAYA000005 x 1]

Power cord [K2CG3FZ00008 x 1]

Battery for remote control unit [R03NW/2ST x 1]

Lens cover [TKKL5244-1 x 1]

Precautions on handling

Precautions on transport

Make absolutely sure that the lens cap is in place when transporting the projector or carrying it around. Both the projector and the projection lens are precision-made and, as such, are susceptible to vibration and impacts. When transporting the projector and lens or carrying them around, place them in the boxes in which they were housed at the time of purchase, and take care to keep them away from vibration and impacts.

Precautions on installation

Be sure to observe the following precautions when installing the product.

Avoid installing the product in a place exposed to vibrations or impacts.

If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or a vessel, vibrations or impacts may be transmitted to the product to damage the internal parts, causing failure. Install the product in a place free from vibrations and impacts.

Do not move the projector while it is operating or subject it to vibration or impact.

The service life of its internal motors may be shortened.

Do not install the projector near highvoltage power lines or power sources.

The product may be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources.

Do not place the projector on a vinyl sheet or carpet.

If a vinyl sheet sucked up and blocks the air filter intake port, the internal temperature of the projector may increase, which triggers the protection circuit, turning off the power.

Be sure to ask a specialized technician when to install the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional hanging attachment (for high ceiling: Model No. ET-PKD55) (for low ceiling: Model No. ET-PKD55S) and call a specialized technician for installation.

Install the projector so that it will be supported only by its bottom panel and by none of its other parts or surfaces.

Do not place the projector over 2 700 m (8 881.5') above sea level. When using it over 1 400 m (4 605.3') above sea level, set the “Fan Control1”, described on page 36, to “HIGHLAND”.

Otherwise the life of the product may be shortened. When using it over 2 700 m above sea level, consult your dealer.

Disposal

To discard the product, call the dealer or a specialized dealer.

Precautions on use

To view clear images:

• The audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the screen surface. Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures.

• In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on the environment.

Do not touch the surface of the projection lens with bare hand.

If fingerprints or stains are left on the projection lens surface, they are magnified and projected on the screen. Keep your hands away from the lens. Cover the lens with the supplied lens cap when the projector is not used.

Lamp

A mercury lamp with high internal pressure is used for the light source of this product. A high-pressure mercury lamp has the following characteristics:

•

It may burst with a loud sound or end its life cycle by not illuminating because of given impacts, flaws, or deterioration due to used hours.

•

The life cycle of a mercury lamp varies according to the individual difference or conditions of use. In particular, turning the power on and off frequently and/or repeatedly will greatly affect the life cycle.

• In rare cases, it may burst shortly after the first lighting.

• The possibility of burst increases when the lamp is used beyond the replacement time.

• If the projector is to be operated continuously round the clock, consult your dealer concerning the alternating lamp operation function (lamp changer function).

Cleaning and maintenance

Be sure to remove the power cord plug from the receptacle before cleaning.

Use soft and dry cloth to clean the cabinet

If stains are hard to remove, use a cloth dampened with a kitchen detergent solution (neutral) and squeezed to wipe the cabinet and finish with a dry cloth. If a chemical wipe is used, follow its instructions.

Do not clean the lens surface with fuzzy or dusty cloth.

If dust adheres to the lens, it will be magnified and projected on the screen. Use a soft and clean cloth to wipe off dust.

Name and function of parts

< When the operation mode selector is

set to Projector >

Remote control operation indicator lamp

The lamp flashes when any remote control button is pressed.

POWER ON ( I ) button (page 23)

Turns on the power if the MAIN POWER has been put to the “l” position.

POWER OFF ( ) button (page 24)

Turns off the power if the MAIN POWER has been put to the “l” position.

Input selector (RGB1, RGB2, DVI, VIDEO, S-VIDEO) button

Use to toggle through the RGB1, RGB2, DVI-D, VIDEO and S-VIDEO input ports.

MENU button (page 28)

Displays and clears the Main Menu. It can also return to the previous screen when the menu is displayed.

Arrow buttons (page 28)

Use these buttons to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

ENTER button (page 28)

Press this button to enter your menu selection or to run function.

FREEZE button (page 26)

Press this button to freeze the image temporarily.

Standard (STD) button (page 28)

Press this button to restore the default factory setting.

SHUTTER button (page 26)

Press this button to black out the image temporarily.

Remote control

Function 1 (FUNC1) button (page 36)

This button can control the functions set in “FUNC1” of the “OPTION2” screen from Main Menu.

Digital Zoom (- D.ZOOM +) buttons (page 26)

Any portion of the picture can be zoomed in.

LENS button (page 25)

Switches to the mode of projection lens adjustment.

ON SCREEN button

This button turns on and off the on-screen indication function.

SYSTEM SELECTOR button

Signal system switching (TV system/System) can be done.

AUTO SETUP button (page 26)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “AUTO SETUP...” appears on the screen.

ID ALL button (page 15)

When two or more main units are used in the system, this button switches to the mode to control them simultaneously with a single remote control.

ID SET button (page 15)

When two or more main units are used in the system, this button specifies the ID of the remote control.

Operation mode selector (Computer/Numeric, Projector) switch (page 15)

Put this selector to the right position to control the projector and to the left position to control the PC or use numeric buttons.

Name and function of parts

<When the operation mode selector is

set to Computer>

PAGE UP/PAGE DOWN buttons

These buttons correspond to the PAGE UP/PAGE DOWN buttons on PC’s keyboard.

( ) buttons

These buttons correspond to the left and right mouse buttons.

ENTER button

Moves the mouse cursor.

Numeric (0-9) buttons

In a system that uses a multiple number of projectors, these buttons serve to specify a particular projector. They are also used to enter the password when the password for service personnel needs to be entered.

Click button (page 15)

This button corresponds to the left mouse button when the operation mode is switched to the Computer position.

Remote control wired terminal (page 16)

To use the wired output terminal, connect the remote control and the main unit with the M3 stereo mini jack cable available in the market.

Remote control transmitter window

Operate the remote control aiming at the remote control receiver window on the main unit.

Note

• To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

AC IN terminal (page 23)

Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket.

Air filter (page 42) Burglar lock

Attach a commercial burglar prevention cable (e.g., from Kensington) to this lock port. It is compatible with the Microsaver Security System from Kensington. Contact details for this company are given below. Kensington Technology Group ACCO Brands Inc. 2885 Campus Drive San Mateo, CA94403 Tel (650)572-2700 Fax (650)572-9675 http://www.kensington.com/ http://www.gravis.com/

Clasp for attaching anti-theft chain

Attach a chain or other fastening device available from a hardware store through this clamp.

Level-adjusting feet (page 23)

Use these feet to adjust the tilt of the projector. (The leveling feet at the front left and right can be adjusted.)

Lens lock button (page 25)

Press this to remove the projection lens.

Projection lens

Lens for projecting images on the screen.

Lens left/right adjusting dial (page 25)

Turn this clockwise to move the screen to the left; conversely, turn it counterclockwise to move it to the right.

Remote control receiver window (front) (page 14)

This window receives the signal beam emitted from the remote control.

Focus ring (page 25)

For focus adjustment. Powered focus adjustment is also available.

Temperature monitor (TEMP) (page 41)

Lighting or blinking of this lamp indicates an abnormal condition of the internal temperature.

LAMP1 monitor (page 41)

This lamp lights up when the time to replace lamp unit 1 is reached. It also blinks if something unusual occurs in the lamp circuit.

LAMP2 monitor (page 41)

This lamp lights up when the time to replace lamp unit 2 is reached. It also blinks if something unusual occurs in the lamp circuit.

Power indicator (page 23)

The lamp lights in red when the MAIN POWER switch is turned to “ | ” (on). It turns to green when the POWER ON button of the remote control or the main unit is pressed.

Lens cap

Cap the lens whenever the projector is left unused.

Ventilation holes

Side-mounted connection terminals (page 13)

Status LED lights (Refer to the figure on the right.)

Front and side of the projector

Status LED lights

• Do not remove the upper cover (white top panel).

Attention

Name and function of parts

Ventilation holes

Lamp unit cover

The lamp unit is housed.

MAIN POWER switch (page 23)

Use this switch to turn on “I” and off “O” the main power applied to the projector.

Remote control receiver window (rear) (page 14)

This also receives the signal beam coming from the remote control.

POWER ON ( I ) button (page 23)

Turns on the power.

POWER OFF ( ) button (page 24)

Turns off the power.

RGB1 button (page 23)

Switches to RGB1 input.

RGB2 button (page 23)

Switches to RGB2 input.

VIDEO button (page 23)

Switches to video input.

S-VIDEO button (page 23)

Switches to S-VIDEO input.

MENU button (page 28)

Displays and clears the Main Menu. It can also return to the previous screen when the menu is displayed. The on-screen display (OSD) selection menu can be displayed by holding down the menu key for at least three seconds.

AUTO SETUP button (page 26)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen.

DVI button (page 23)

Switches to DVI-D input.

SHUTTER button (page 26)

Press this button to black out the image temporarily.

ENTER button (page 28)

Press this button to enter your menu selection or to run function.

LENS button (page 25)

Switches to the adjustment mode for lens focus, zoom and shift (position).

Arrow ( ) buttons (page 28)

Use to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

Rear view of the main unit Controls on rear panel

Controls on rear panel

VIDEO IN terminal (page 22)

An input terminal for video signals. (BNC)

S-VIDEO IN terminal (page 22)

An input terminal for S-video signals. (MIN4-pin DIN) This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals.

RGB 1 input (RGB 1 IN) terminal (page 22)

A terminal to input RGB or YPB

PR signals. (BNC)

RGB 2 input (RGB 2 IN) terminal (page 22)

A terminal to input RGB or YPBPR signals. (D-SUB 15-pin female)

DVI-D IN terminal (page 22)

DVI-D signals are applied to this terminal. (24-pin DVI connector)

LAN terminal (page 38)

This terminal is used to control the projector from the PC. (10Base-T/100Base-TX compliant)

REMOTE1 lN/OUT terminal (page 16)

When two or more main units are used in the system, they can be connected and controlled with M3 stereo mini jack cable available in the market.

REMOTE2 IN terminal

The user can remotely control the main unit by using an external control circuit to this terminal. (D-SUB 9-pin female)

SERIAL IN terminal (pages 22, 39)

Use the RS232C serial terminal as an alternative interface for controlling the projector from your PC. (D-SUB 9-pin female)

SERIAL OUT terminal (pages 22, 39)

The signal applied to the serial input terminal appears at this terminal. (D-SUB 9-pin male)

RGB 2 IN

SYNC/HD

B/P

G/Y

R/P

SERIAL

REMOTE 1

REMOTE 2

OUT

LAN

DVI-D IN

RGB 1 IN

VIDEO IN

S-VIDEO IN

IN OUT

Side-mounted connection terminals

LAN terminal (10Base-T/100Base-TX)

Connect LAN cable.

LAN 10/100 lamp (Yellow)

Lights up when 100Base-TX connected.

LAN LINK/ACT lamp (Green)

Lights up when connected. Flashes when receiving/sending signals.

Using the remote control unit

Loading dry cells

When loading batteries into the battery compartment of the remote control, make sure that their polarities are correct.

1.Open battery compartment lid.

Open the lid in the order of steps and .

2.Insert the dry cells.

Into battery compartment, with their polarities orientated as indicated ( , ) in the

compartment.

3.Close the battery compartment lid.

Replace the battery compartment lid over the compartment and slide until it clicks.

Effective range of remote control operation

The remote control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). Otherwise, it may also be aimed at the screen, which will reflect commands back to the projector’s front receiver window as illustrated in figure 2.

The effective control range is approx. 7 meters from the beam receiver on the front or rear.

• Do not drop the remote control unit.

• Do not expose remote control unit to

any liquid.

• Do not use NiCd batteries.

Attention

Note

• When the remote control is aimed at the screen, the effective control range may be reduced due to the optical loss by screen reflection.

• The remote control may not function properly if an object is in the light path.

• The remote control receiver may not function properly in intense ambient light such as fluorescent lamps. Carefully site the projector so its remote control receiver windows will not be directly exposed to intense light.

Accessory type-AAA dry batteries (insert the negative side first).

(Front)

(Rear)

[Top view]

[Side view]

Remote control

15˚

30˚

Remote control receiver window (rear)

Remote control receiver window (front)

Projector

Remote control

Screen

Figure 1

Figure 2

Using the remote control as a PC mouse

Operation mode selector switch

Put the knob to the Computer position.

• ENTER button

Pressing the front, rear, left and right edges of the button moves the mouse cursor up, down, left and right.

• Right click ( ) button

This button can be used as the right mouse button.

• Left click ( ) button

This button can be used as the left mouse button.

• PAGE UP button

This button can be used as the Page Up button on the PC keyboard.

• PAGE DOWN button

This button can be used as the Page Down button on the PC keyboard.

• Click button

This button can be used as the left mouse button.

PAGE DOWN button

Operation mode selector switch

ENTER button Right click ( ) button

PAGE UP button

Left click ( ) button

Click button

• To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

Note

Setting projector ID number to remote control

Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to

“ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.

Procedure of ID setting

Change the position of the operation mode selector switch to “Computer”. Press the ID SET button, and within five seconds use the number (0 to 9) buttons to

enter the 2-digit ID number set by the projector. Change the position of the operation mode selector switch to “Projector”.

However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the projector (simultaneous control mode).

• Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around. If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID SET button unless a numeric button is pressed within five seconds after the ID SET button is pressed.

• Your specified ID number is stored in the remote control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the dry cells are replaced, set the same ID number again.

• When specifying the ID number, enter a 2-digit number even if the ID has only one digit.

(Example: set “02” if the ID number is “2.”)

Attention

Using a wired remote control

When multiple main units are connected in the system, connect the units with the M3 stereo mini jack cable available in the market to simultaneously control the multiple main units with a single remote control unit through the REMOTE1 IN/OUT terminal. It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

B/P

G/Y

R/P

REMOTE 1

REMOTE 2

RGB 1 IN

VIDEO IN

S-VIDEO IN

IN OUT

Connect to the secondary projector

M3 stereo mini jack cable (available in the market)

Using the remote control unit

• Use two-core shielded cable of length smaller than 15 m (49' 2"). If the cable length exceeds 15 m (49' 2"), or if the shielding of the cable is inadequate, the operation may be unsatisfactory.

Attention

Installation

Projection Scheme 1

Front projection

Rear projection

Table standing

Projection Scheme 2

Ceiling mount

(Default position)

Installation geometry

After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens tilt mechanism.

Side view

With optional ceiling mount bracket (ET-PKD55)

261

(10

/32)

Screen

180

(7 3/32)

;

421-541

(16

/64-21

/64)

Top view

314

(12

/64)

157

/16)

175 (6 57/64)

87.5 (3

/64)

Screen

L : Projection distance SH : Image height SW : Image width H : Distance from center of lens to bottom edge

of projected image.

• Do not place or use one projector on top of another projection unit.

• Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be blocked.

Attention

Projection schemes

Any of the following four projection schemes can be used depending on user’s needs or viewing conditions. Use “OPTION2” menu (chosen from the MAIN MENU) to choose the appropriate projection scheme (see page 35).

Projection distance by projection lens

Listed in the table below are the lens projection distances for the PT-D5600U (lens included), PT-D5600UL (lens sold separately), PT-DW5000U (lens included) and PT-DW5000UL (lens sold separately).

• PT-D5600U, PT-D5600UL

1.27

(50")

1.52

(60")

1.78

(70")

2.03

(80")

2.29

(90")

2.54

(100")

3.05

(120")

3.81

(150")

5.08

(200")

6.35

(250")

7.62

(300")

8.89

(350")

10.16

(400")

12.70

(500")

15.24

(600")

Diagonal

length

(SD)

Height

(SH)

1.02

[3'33"]

1.22

[4'00"]

1.42

[4'67"]

1.63

[5'33"]

1.83

[6'00"]

2.03

[6'66"]

2.44

[8'00"]

3.05

[10'00"]

4.06

[13'33"]

5.08

[16'66"]

6.10

[19'99"]

7.11

[23'33"]

8.13

[26'66"]

10.16

[33'32"]

12.19

[39'99"]

Width

(SW)

Minimum

(LW)

Maximum

(LT)

1.79

[5'85"]

2.16

[7'07"]

2.53

[8.28"]

2.90

[9'50"]

3.27

[10'71"]

3.64

[11'92"]

4.38

[14'35"]

5.49

[17'99"]

7.34

[24'06"]

9.19

[30'13"]

11.04

[36'19"]

12.89

[42'26"]

14.74

[48'33"]

18.44

[60'47"]

22.14

[72'60"]

Minimum

(LW)

2.38

[7'79"]

2.86

[9'39"]

3.35

[11'00"]

3.84

[12'60"]

4.33

[14'20"]

4.82

[15'80"]

5.79

[19'00"]

7.26

[23'80"]

9.70

[31'80"]

12.14

[39'81"]

14.58

[47'81"]

17.02

[55'81"]

19.46

[63'82"]

24.34

[79'82"]

29.22

[95'83"]

Maximum

(LT)

Minimum

(LW)

Maximum

(LT)

0.79

[2'60"]

0.96

[3'15"]

1.13

[3'69"]

1.29

[4'24"]

1.46

[4'78"]

1.62

[5'33"]

1.96

[6'42"]

2.45

[8'05"]

3.28

[10'77"]

–

Model No. :

ET-DLE050

Projected screen size

(4:3 aspect ratio)

Wide-angle

zoom lens

Model No. :

ET-DLE100

Standard

zoom lens

Minimum

(LW)

Maximum

(LT)

Intermediatefocus

zoom lens Model No. : ET-DLE200

Optional lens

Long-focus

zoom lens Model No. : ET-DLE300

Wide-angle fixed-focus

lens

(0.8)

(L)

(1.33–1.78)(1.8–2.5) (2.5–4.0) (3.7–5.7)

Minimum

(LW)

Maximum

(LT)

Ultra-long-focus

zoom lens Model No. : ET-DLE400

Height

position: H*

(5.7–8.0)

Unit : m, ( ) : inch, [ ] : foot

Screen aspect ratio 4:3

0.76

[2'50"]

0.91

[3'00"]

1.07

[3'50"]

1.22

[4'00"]

1.37

[4'50"]

1.52

[5'00"]

1.83

[6'00"]

2.29

[7'50"]

3.05

[10'00"]

3.81

[12'50"]

4.57

[15'00"]

5.33

[17'50"]

6.10

[19'99"]

7.62

[24'99"]

9.14

[29'99"]

1.33

[4'38"]

1.61

[5'28"]

1.89

[6'19"]

2.16

[7'09"]

2.44

[8'00"]

2.71

[8'90"]

3.27

[10'72"]

4.09

[13'43"]

5.47

[17'96"]

6.85

[22'48"]

8.23

[27'01"]

9.61

[31'54"]

10.99

[36'06"]

13.75

[45'12"]

16.51

[54'17"]

1.81

[5'94"]

2.18

[7'16"]

2.56

[8'38"]

2.93

[9'60"]

3.30

[10'82"]

3.67

[12'04"]

4.42

[14'49"]

5.53

[18'15"]

7.39

[24'25"]

9.25

[30'35"]

11.11

[36'45"]

12.97

[42'55"]

14.83

[48'65"]

18.55

[60'85"]

22.27

[73'05"]

3.84

[12'59"]

4.63

[15'19"]

5.43

[17'80"]

6.22

[20'41"]

7.02

[23'02"]

7.81

[25'62"]

9.40

[30'84"]

11.79

[38'66"]

15.76

[51'70"]

19.74

[64'74"]

23.71

[77'78"]

27.69

[90'81"]

31.66

[103'85"]

39.61

[129'93"]

47.56

[156'00"]

6.03

[19'78"]

7.26

[23'82"]

8.49

[27'86"]

9.73

[31'90"]

10.96

[35'94"]

12.19

[39'98"]

14.65

[48'06"]

18.35

[60'18"]

24.51

[80'39"]

30.67

[100'59"]

36.83

[120'80"]

42.99

[141'00"]

49.15

[161'21"]

61.47

[201'62"]

73.79

[242'03"]

2.45

[8'05"]

2.96

[9'70"]

3.46

[11'36"]

3.97

[13'01"]

4.47

[14'66"]

4.97

[16'32"]

5.98

[19'62"]

7.49

[24'58"]

10.01

[32'85"]

12.53

[41'11"]

15.05

[49'38"]

17.57

[57'64"]

20.09

[65'91"]

25.13

[82'44"]

30.17

[98'97"]

4.04

[13'26"]

4.87

[15'97"]

5.69

[18'67"]

6.52

[21'37"]

7.34

[24'08"]

8.16

[26'78"]

9.81

[32'18"]

12.28

[40'29"]

16.40

[53'81"]

20.52

[67'32"]

24.64

[80'83"]

28.76

[94'35"]

32.88

[107'86"]

41.12

[134'89"]

49.36

[161'91"]

5.90

[19'37"]

7.08

[23'22"]

8.26

[27'08"]

9.43

[30'94"]

10.61

[34'80"]

11.78

[38'65"]

14.14

[46'37"]

17.66

[57'94"]

23.54

[77'23"]

29.42

[96'51"]

35.30

[115'80"]

41.18

[135'08"]

47.06

[154'37"]

58.82

[192'94"]

70.58

[231'52"]

8.30

[27'21"]

9.94

[32'61"]

11.59

[38'01"]

13.23

[43'40"]

14.88

[48'80"]

16.53

[54'20"]

19.82

[65'00"]

24.76

[81'20"]

32.99

[108'19"]

41.22

[135'19"]

49.45

[162'18"]

57.68

[189'17"]

65.91

[216'17"]

82.37

[270'16"

]

98.83

[324'15"]

0 to 0.38

(0 to 14 61/64)

0 to 0.46

(0 to 18 7/64)

0 to 0.53

(0 to 20 55/64)

0 to 0.61

(0 to 24 1/64)

0 to 0.69

(0 to 27 11/64)

0 to 0.76

(0 to 29 59/64)

0 to 0.91

(0 to 35 53/64)

0 to 1.14

(0 to 44 7/8)

0 to 1.52

(0 to 59 27/32)

0 to 1.91

(0 to 75 13/64)

0 to 2.29

(0 to 90 5/32)

0 to 2.67

(0 to 105 1/8)

0 to 3.05

(0 to 120 5/64)

0 to 3.81

(0 to 150)

0 to 4.57

(0 to 179 59/64)

* The height position (H) of the ET-DLE050 is SH/2.

Installation

1.27

(50")

1.52

(60")

1.78

(70")

2.03

(80")

2.29

(90")

2.54

(100")

3.05

(120")

3.81

(150")

5.08

(200")

6.35

(250")

7.62

(300")

8.89

(350")

10.16

(400")

12.70

(500")

15.24

(600")

Diagonal

length

(SD)

Height

(SH)

Width

(SW)

Minimum

(LW)

Maximum

(LT)

Minimum

(LW)

Maximum

(LT)

Minimum

(LW)

Maximum

(LT)

Model No. :

ET-DLE050

Projected screen size

(16:9 aspect ratio)

Wide-angle

zoom lens

Model No. :

ET-DLE100

Standard

zoom lens

Minimum

(LW)

Maximum

(LT)

Intermediatefocus

zoom lens Model No. : ET-DLE200

Optional lens

Long-focus

zoom lens Model No. : ET-DLE300

Wide-angle fixed-focus

lens

(0.8)

(L)

(1.33–1.78)(1.8–2.5) (2.5–4.0) (3.7–5.7)

Minimum

(LW)

Maximum

(LT)

Ultra-long-focus

zoom lens Model No. : ET-DLE400

Height

position: H*

(5.7–8.0)

Unit : m, ( ) : inch, [ ] : foot

Screen aspect ratio 16:9

0.62

[2'04"]

0.75

[2'45"]

0.87

[2'86"]

1.00

[3'27"]

1.12

[3'68"]

1.25

[4'08"]

1.49

[4'90"]

1.87

[6'13"]

2.49

[8'17"]

3.11

[10'21"]

3.74

[12'25"]

4.36

[14'30"]

4.98

[16'34"]

6.23

[20'42"]

7.47

[24'51"]

1.11

[3'63"]

1.33

[4'36"]

1.55

[5'08"]

1.77

[5'81"]

1.99

[6'54"]

2.21

[7'26"]

2.66

[8'71"]

3.32

[10'89"]

4.43

[14'52"]

5.53

[18'15"]

6.64

[21'78"]

7.75

[25'41"]

8.86

[29'05"]

11.07

[36'31"]

13.28

[43'57"]

1.46

[4'79"]

1.76

[5'78"]

2.06

[6'76"]

2.36

[7'75"]

2.66

[8'74"]

2.96

[9'72"]

3.57

[11'70"]

4.47

[14'66"]

5.97

[19'60"]

7.48

[24'53"]

8.98

[29'47"]

10.49

[34'41"]

11.99

[39'34"]

15.00

[49'22"]

18.01

[59'09"]

1.98

[6'49"]

2.38

[7'81"]

2.79

[9'14"]

3.19

[10'47"]

3.60

[11'80"]

4.00

[13'13"]

4.81

[15'78"]

6.03

[19'77"]

8.05

[26'41"]

10.08

[33'05"]

12.10

[39'70"]

14.13

[46'34"]

16.15

[52'98"]

20.20

[66'26"]

24.25

[79'55"]

1.95

[6'40"]

2.35

[7'72"]

2.76

[9'04"]

3.16

[10'36"]

3.56

[11'68"]

3.97

[13'01"]

4.77

[15'65"]

5.98

[19'61"]

8.00

[26'22"]

10.01

[32'83"]

12.03

[39'44"]

14.04

[46'05"]

16.06

[52'66"]

20.09

[65'88"]

24.12

[79'10"]

2.60

[8'52"]

3.13

[10'26"]

3.66

[12'01"]

4.19

[13'75"]

4.72

[15'50"]

5.26

[17'24"]

6.32

[20'73"]

7.92

[25'97"]

10.58

[34'69"]

13.24

[43'41"]

15.90

[52'14"]

18.56

[60'86"]

21.22

[69'59"]

26.54

[87'04"]

31.86

[104'49"]

4.19

[13'75"]

5.06

[16'59"]

5.92

[19'43"]

6.79

[22'27"]

7.66

[25'11"]

8.52

[27'95"]

10.25

[33'63"]

12.85

[42'15"]

17.18

[56'36"]

21.51

[70'56"]

25.84

[84'76"]

30.17

[98'96"]

34.50

[113'17"]

43.16

[141'57"]

51.82

[169'98"]

6.58

[21'58"]

7.92

[25'98"]

9.26

[30'38"]

10.61

[34'78"]

11.95

[39'19"]

13.29

[43'59"]

15.97

[52'39"]

20.00

[65'60"]

26.71

[87'61"]

33.42

[109'61"]

40.13

[131'62"]

46.84

[153'63"]

53.55

[175'64"]

66.97

[219'66"]

80.39

[263'68"]

0.87

[2'85"]

1.05

[3'44"]

1.23

[4'04"]

1.41

[4'63"]

1.59

[5'22"]

1.77

[5'82"]

2.14

[7'01"]

2.68

[8'79"]

3.58

[11'76"]

–

2.68

[8'79"]

3.23

[10'59"]

3.78

[12'39"]

4.33

[14'19"]

4.88

[15'99"]

5.42

[17'79"]

6.52

[21'39"]

8.17

[26'80"]

10.91

[35'80"]

13.66

[44'80"]

16.40

[53'81"]

19.15

[62'81"]

21.89

[71'81"]

27.38

[89'82"]

32.87

[107'83"]

4.41

[14'48"]

5.31

[17'42"]

6.21

[20'37"]

7.11

[23'31"]

8.01

[26'26"]

8.90

[29'21"]

10.70

[35'10"]

13.39

[43'93"]

17.88

[58'66"]

22.37

[73'39"]

26.86

[88'11"]

31.35

[102'84"]

35.84

[117'57"]

44.82

[147'02"]

53.80

[176'48"]

6.43

[21'09"]

7.71

[25'29"]

8.99

[29'49"]

10.27

[33'69"]

11.55

[37'90"]

12.83

[42'10"]

15.40

[50'50"]

19.24

[63'11"]

25.64

[84'11"]

32.05

[105'12"]

38.45

[126'13"]

44.86

[147'14"]

51.26

[168'15"]

64.07

[210'16"]

76.88

[252'18"]

9.03

[29'62"]

10.82

[35'50"]

12.62

[41'38"]

14.41

[47'26"]

16.20

[53'14"]

18.00

[59'02"]

21.58

[70'79"]

26.96

[88'43"]

35.93

[117'83"]

44.89

[147'24"]

53.86

[176'64"]

62.82

[206'05"]

71.79

[235'46"]

89.72

[294'27"]

107.65

[353'08"]

0 to 0.38

(0 to 14 61/64)

0 to 0.46

(0 to 18 7/64)

0 to 0.53

(0 to 20 55/64)

0 to 0.61

(0 to 24 1/64)

0 to 0.69

(0 to 27 11/64)

0 to 0.76

(0 to 29 59/64)

0 to 0.91

(0 to 35 53/64)

0 to 1.14

(0 to 44 7/8)

0 to 1.52

(0 to 59 27/32)

0 to 1.91

(0 to 75 13/64)

0 to 2.29

(0 to 90 5/32)

0 to 2.67

(0 to 105 1/8)

0 to 3.05

(0 to 120 5/64)

0 to 3.81

(0 to 150)

0 to 4.57

(0 to 179 59/64)

* The height position (H) of the ET-DLE050 is SH/2.

• PT-DW5000U, PT-DW5000UL

Screen aspect ratio 16:9

Diagonal

length

(SD)

Height

(SH)

Width

(SW)

Minimum

(LW)

Maximum

(LT)

Minimum

(LW)

Maximum

(LT)

Minimum

(LW)

Maximum

(LT)

Model No. :

ET-DLE050

Projected screen size

(16:9 aspect ratio)

Wide-angle

zoom lens Model No. : ET-DLE100

Standard

zoom lens

Minimum

(LW)

Maximum

(LT)

Intermediatefocus

zoom lens

Model No. :

ET-DLE200

Optional lens

Long-focus

zoom lens Model No. : ET-DLE310

Wide-angle fixed-focus

lens

(0.8)

(L)

(1.33–1.78)(1.8–2.5) (2.5–4.0) (3.4–4.5)

Minimum

(LW)

Maximum

(LT)

Ultra-long-focus

zoom lens Model No. : ET-DLE410

Height

position: H*

(4.5–8.4)

Unit : m, ( ) : inch, [ ] : foot

1.27

(50")

1.52

(60")

1.78

(70")

2.03

(80")

2.29

(90")

2.54

(100")

3.05

(120")

3.81

(150")

5.08

(200")

6.35

(250")

7.62

(300")

8.89

(350")

10.16

(400")

12.70

(500")

15.24

(600")

0.62

[2'04"]

0.75

[2'45"]

0.87

[2'86"]

1.00

[3'27"]

1.12

[3'68"]

1.25

[4'08"]

1.49

[4'90"]

1.87

[6'13"]

2.49

[8'17"]

3.11

[10'21"]

3.74

[12'25"]

4.36

[14'30"]

4.98

[16'34"]

6.23

[20'42"]

7.47

[24'51"]

1.11

[3'63"]

1.33

[4'36"]

1.55

[5'08"]

1.77

[5'81"]

1.99

[6'54"]

2.21

[7'26"]

2.66

[8'71"]

3.32

[10'89"]

4.43

[14'52"]

5.53

[18'15"]

6.64

[21'78"]

7.75

[25'41"]

8.86

[29'05"]

11.07

[36'31"]

13.28

[43'57"]

1.48

[4'85"]

1.78

[5'85"]

2.09

[6'85"]

2.39

[7'85"]

2.70

[8'86"]

3.00

[9'86"]

3.61

[11'86"]

4.53

[14'86"]

6.05

[19'86"]

7.58

[24'86"]

9.10

[29'86"]

10.63

[34'87"]

12.15

[39'87"]

15.20

[49'87"]

18.25

[59'88"]

2.01

[6'58"]

2.42

[7'93"]

2.83

[9'28"]

3.24

[10'63"]

3.65

[11'98"]

4.06

[13'32"]

4.88

[16'02"]

6.12

[20'06"]

8.17

[26'80"]

10.23

[33'55"]

12.28

[40'29"]

14.34

[47'03"]

16.39

[53'77"]

20.50

[67'25"]

24.61

[80'73"]

1.98

[6'49"]

2.39

[7'84"]

2.80

[9'18"]

3.21

[10'52"]

3.62

[11'86"]

4.03

[13'20"]

4.84

[15'89"]

6.07

[19'91"]

8.12

[26'62"]

10.16

[33'32"]

12.21

[40'03"]

14.25

[46'74"]

16.30

[53'45"]

20.39

[66'86"]

24.48

[80'28"]

2.63

[8'63"]

3.17

[10'40"]

3.71

[12'17"]

4.25

[13'93"]

4.79

[15'70"]

5.33

[17'47"]

6.40

[21'01"]

8.02

[26'31"]

10.72

[35'15"]

13.41

[43'99"]

16.11

[52'83"]

18.80

[61'67"]

21.50

[70'51"]

26.89

[88'19"]

32.28

[105'87"]

3.89

[12'76"]

4.69

[15'38"]

5.49

[18'00"]

6.29

[20'62"]

7.08

[23'24"]

7.88

[25'86"]

9.48

[31'10"]

11.88

[38'96"]

15.87

[52'07"]

19.87

[65'17"]

23.86

[78'27"]

27.86

[91'38"]

31.85

[

104'48"

]

39.84

[130'69"]

47.83

[156'89"]

5.11

[16'76"]

6.15

[20'18"]

7.20

[23'60"]

8.24

[27'02"]

9.28

[30'44"]

10.32

[33'86"]

12.41

[40'71"]

15.54

[50'97"]

20.75

[68'07"]

25.97

[85'18"]

31.18

[102'28"]

36.40

[119'39"]

41.61

[136'50"]

52.04

[170'71"]

62.47

[204'92"]

0.88

[2'88"]

1.06

[3'48"]

1.24

[4'08"]

1.43

[4'68"]

1.61

[5'28"]

1.79

[5'88"]

2.16

[7'08"]

2.71

[8'89"]

3.62

[11'89"]

–

2.71

[8'90"]

3.27

[10'73"]

3.83

[12'55"]

4.38

[14'37"]

4.94

[16'20"]

5.49

[18'02"]

6.61

[21'67"]

8.27

[27'14"]

11.05

[36'26"]

13.83

[45'38"]

16.61

[54'49"]

19.39

[63'61"]

22.17

[72'73"]

27.73

[90'97"]

33.29

[109'21"]

4.47

[14'68"]

5.38

[17'66"]

6.29

[20'64"]

7.20

[23'63"]

8.11

[26'61"]

9.02

[29'60"]

10.84

[35'57"]

13.57

[44'52"]

18.12

[59'45"]

22.67

[74'37"]

27.22

[89'30"]

31.77

[104'22"]

36.32

[119'14"]

45.42

[148'99"]

54.52

[178'84"

]

5.17

[16'95"]

6.23

[20'43"]

7.29

[23'91"]

8.35

[27'39"]

9.41

[30'87"]

10.47

[34'35"]

12.59

[41'31"]

15.78

[51'75"]

21.08

[69'15"]

26.39

[86'55"]

31.69

[103'95"]

37.00

[121'35"]

42.30

[138'75"]

52.91

[173'55"]

63.52

[208'35"]

9.78

[32'08"]

11.76

[38'58"]

13.75

[45'09"]

15.73

[51'59"]

17.71

[58'09"]

19.69

[64'60"]

23.66

[77'61"]

29.61

[97'12"]

39.52

[129'64"]

49.44

[162'16"]

59.35

[194'68"]

69.27

[227'20"]

79.18

[259'73"]

99.01

[324'77"]

118.84

[389'81"]

0 to 0.38

(0 to 14 61/64)

0 to 0.46

(0 to 18 7/64)

0 to 0.53

(0 to 20 55/64)

0 to 0.61

(0 to 24 1/64)

0 to 0.69

(0 to 27 11/64)

0 to 0.76

(0 to 29 59/64)

0 to 0.91

(0 to 35 53/64)

0 to 1.14

(0 to 44 7/8)

0 to 1.52

(0 to 59 27/32)

0 to 1.91

(0 to 75 13/64)

0 to 2.29

(0 to 90 5/32)

0 to 2.67

(0 to 105 1/8)

0 to 3.05

(0 to 120 5/64)

0 to 3.81

(0 to 150)

0 to 4.57

(0 to 179 59/64)

* The height position (H) of the ET-DLE050 is SH/2.

Note • Black bands will appear at the top and bottom of the screen.

Installation

Calculation formulas for projection distance by lens types

• PT-D5600U, PT-D5600UL

Standard zoom lens Wide-angle fixedfocus lens Wide-angle zoom lens Intermediate-focus zoom lens Long-focus zoom lens Ultra-long-focus zoom lens

Model No. : ET-DLE050 Model No. : ET-DLE100 Model No. : ET-DLE200 Model No. : ET-DLE300 Model No. : ET-DLE400

Minimum (LW) Maximum (LT)

Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT)

L=0.0370 x SD-0.0650 L=0.0488 x SD-0.0638

L=0.0166 x SD-0.0361

L=0.0276 x SD-0.0452 L=0.0372 x SD-0.0478 L=0.0504 x SD-0.0657 L=0.0824 x SD-0.0758 L=0.0795 x SD-0.1380 L=0.1232 x SD-0.1310 L=0.1176 x SD+0.0244 L=0.1646 x SD+0.0651

(L, LW, LT : m SD : inch)Screen aspect ratio 4:3

Standard zoom lens Wide-angle fixedfocus lens Wide-angle zoom lens Intermediate-focus zoom lens Long-focus zoom lens Ultra-long-focus zoom lens

Model No. : ET-DLE050 Model No. : ET-DLE100 Model No. : ET-DLE200 Model No. : ET-DLE300 Model No. : ET-DLE400

Minimum (LW) Maximum (LT)

Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT)

L=0.0403 x SD-0.0650 L=0.0532 x SD-0.0638

L=0.0181 x SD-0.0361

L=0.0301 x SD-0.0452 L=0.0405 x SD-0.0478 L=0.0549 x SD-0.0657 L=0.0898 x SD-0.0758 L=0.0866 x SD-0.1380 L=0.1342 x SD-0.1310 L=0.1281 x SD+0.0244 L=0.1793 x SD+0.0651

(L, LW, LT : m SD : inch)Screen aspect ratio 16:9

• PT-DW5000U, PT-DW5000UL

Screen aspect 16:9

Standard zoom lens Wide-angle fixedfocus lens Wide-angle zoom lens Intermediate-focus zoom lens Long-focus zoom lens Ultra-long-focus zoom lens

Model No. : ET-DLE050 Model No. : ET-DLE100 Model No. : ET-DLE200 Model No. : ET-DLE310 Model No. : ET-DLE410

Minimum (LW) Maximum (LT)

Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT) Minimum (LW) Maximum (LT)

L=0.0409 x SD-0.0650 L=0.0539 x SD-0.0638

L=0.0183 x SD-0.0361

L=0.0305 x SD-0.0452 L=0.0411 x SD-0.0478 L=0.0556 x SD-0.0657 L=0.0910 x SD-0.0758 L=0.0799 x SD-0.1062 L=0.1043 x SD-0.1056 L=0.1061 x SD-0.1374 L=0.1983 x SD-0.1352

(L, LW, LT : m SD : inch)

Note

• The dimensions in the table in pages 17-19 and the values obtained from the above formulas may contain slight errors.

• When an SXGA signal is input and projected, the right and left ends of the picture will be blanked and the aspect ratio will be 5:4.

• The brightness is different between the wide lens position settings and telephoto lens position settings.

Connection

Setup precautions

• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual supplied with the equipment once again.

• All cable connections should be made with the entire system devices, including the projector, first turned off.

• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect

cables.

• Video signals containing too much jitter may cause the images on the screen to randomly wobble or shake. Inserting a time base corrector (TBC) in the projector’s video line will relieve this problem.

• The projector only accepts composite-video, S-video, analog-RGB (with TTL sync. level), and digital signal.

• Some PC models are not compatible with PT-D5600U/PT-D5600UL/PT-DW5000U/PT-DW5000UL projectors.

• The pin assignments on the S-VIDEO IN terminal are

as follows:

• The pin assignments on the DVI-D input terminal are as follows (interface with DVI-D output terminal on PC):

• The pin assignments on the RGB2 input terminal are as follows:

Viewed from mating side

Pin No.

Signal Ground (luminance) Ground (colour) Luminance signal Colour signal

Pin : Not used. Pins - , and : Ground.

Viewed from mating side

Signal

R/P

G/G · SYNC/Y B/P

HD/SYNC VD

Pin No.

Viewed from mating side

Pin No.

Signal T. M. D. S data 2T. M. D. S data 2+ T. M. D. S data 2 shield

DDC clock DDC data

T. M. D. S data 1T. M. D. S data 1+ T. M. D. S data 1 shield

Signal

+5 V Ground Hot plug sense T. M. D. S data 0T. M. D. S data 0+ T. M. D. S data 0 shield

T. M. D. S clock shield T. M. D. S clock+ T. M. D. S clock-

Pin No.

• The DVI-D input terminal supports single link only.

• EDID settings should be performed to suit the DVI

equipment being connected. (Page 34)

• The DVI-D input terminal can be used to connect to a DVI equipment, but note that images may not appear or the projector may not work properly when connected to certain DVI equipment.

• This projector supports HDCP.

+ 47 hidden pages