Panasonic PTAE700U-EC, PT-AE700U Operating Instructions Manual

ENGLISH

TQBJ 0161-1

LCD Projector

Operating Instructions

Model No. PT-AE700U

R

Before operating this product, please read the instructions carefully and save this

manual for future use.

For assistance, please call : 1-888-View-PTV(843-9788)

or send e-mail to : [e-mail]
or visit us at www.panasonic.com (U.S.A)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.co.jp/global/ (Puerto Rico)

2-ENGLISH

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should
note it in the space provided below and retain this booklet in case service is
required.

Model number: PT-AE700U

Serial number:

ENGLISH-3

Preparation

IMPORTANT SAFETY NOTICE

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.

Power Supply: This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60

Hz AC, house current only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can

only be used for power supplies up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.

Declaration of Conformity

Model Number: PT-AE700U
Trade Name: Panasonic
Responsible party: Matsushita Electric Corporation of America.
Address: One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-888-View-PTV(843-9788)
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

CAUTION:

This equipment is equipped with a three­pin grounding-type power plug. Do not
remove the grounding pin on the power
plug. This plug will only fit a grounding­type power outlet. This is a safety feature.
If you are unable to insert the plug into
the outlet, contact an electrician. Do not
defeat the purpose of the grounding plug.

WARNING:

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when

connecting to computers or peripheral devices.
Any unauthorized changes or modifications to this equipment will void the
users authority to operate.

Do not remove

WARNING:

Not for use in a computer room as defined in the Standard for the Protection
of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

ENGLISH-5

Preparation

4-ENGLISH

Contents

Preparation

IMPORTANT SAFETY NOTICE ...2
Precautions with regard to

safety .........................................5

Accessories .................................9

Before use ....................................9

Location and function of each

part...........................................11

Getting started

Setting-up...................................16

Projection methods, Projector
position, Projection distances,
Setting up range using the lens shift
function

Connections...............................20

Connecting to video equipment,
Connecting to equipment
compatible with HDMI,
Connecting to computer

Preparation for the remote

control unit..............................23

Basic operation

Turning on the power................24

Turning off the power................26

Useful functions

Correcting keystone distortion

...28

Pausing a picture.......................28

Selecting the picture mode.......29

Turning on the button lights.....29

Setting the aspect ratio.............30

Using the COLOR MANAGEMENT

...32
Retrieving the saved picture

settings....................................35

Adjustments and settings

On-screen menus ......................36

Menu screens, Menu operation
guide, Returning a setting to the
factory default

Adjusting the picture.................40

PICTURE MODE, CONTRAST,
BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP.,

DYNAMIC IRIS, ADVANCE MENU,
MEMORY SAVE, MEMORY LOAD,
TV-SYSTEM, SIGNAL MODE,
Projecting sRGB-compatible pictures

Adjusting the position...............44

Horizontal position, Vertical position,
DOT CLOCK, CLOCK PHASE,
ASPECT,AUTO SETUP

Turning off the picture

momentarily (SHUTTER)........45

Changing the display language

...45

Option settings ..........................46

OSD, Noise Reduction (NR),
CINEMA REALITY, BACK COLOR,
WSS, FRONT/REAR,
DESK/CEILING, FAN CONTROL,
LAMP POWER, LAMP RUNTIME

Care and maintenance

When the TEMP indicator and the

LAMP indicator are illuminated

...48

Cleaning and replacing

the air filter ..............................50

Replacing the lamp unit ............51

Before calling for service..........54

Cleaning and maintenance .......55

Others

Specifications ............................56

Appendix ....................................58

List of compatible signals, General
arrangement of the COLOR
MANAGEMENT menu, Projection
dimensions calculation methods

Dimensions ................................61

Trademark acknowledgements

...62

Precautions with regard to safety

WARNING

If you notice smoke, strange smells or noise coming from the projector,
disconnect the power cord plug from the wall outlet.

B Do not continue to use the projector in such cases, otherwise fire or

electric shocks could result.

B Check that no more smoke is coming out, and then contact an Authorized

Service Center for repairs.

B Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to
take the full weight of the projector.

B If the installation location is not strong enough, it may fall down or tip over,

and severe injury or damage could result.

Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.

B If installation is not carried out correctly, there is the danger that injury or

electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, disconnect the power cord plug from
the wall outlet.

B Continued use of the projector in this condition may result in fire or electric

shocks.

B Contact an Authorized Service Center for repairs.

Do not overload the wall outlet.

B If the power supply is overloaded (for example, by using too many

adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

B High voltages can cause fire or electric shocks.
B For any inspection, adjustment and repair work, please contact an

Authorized Service Center.

Clean the power cord plug regularly to prevent it from becoming
covered in dust.

B If dust builds up on the power cord plug, the resulting humidity can

damage the insulation, which could result in fire. Pull the power cord plug
out from the wall outlet and wipe it with a dry cloth.

B If not using the projector for an extended period of time, pull the power

cord plug out from the wall outlet.

ENGLISH-7

Preparation

6-ENGLISH

Do not do anything that might damage the power cord or the power
cord plug.

B Do not damage the power cord, make any modifications to it, place it near

any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.

B If the power cord is used while damaged, electric shocks, short-circuits or

fire may result.

B Ask an Authorized Service Center to carry out any repairs to the power

cord that might be necessary.

Do not handle the power cord plug with wet hands.

B Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

B If the plug is not inserted correctly, electric shocks or overheating could

result.

B Do not use plugs which are damaged or wall outlets which are coming

loose from the wall.

Do not place the projector on top of surfaces which are unstable.

B If the projector is placed on top of a surface which is sloped or unstable, it

may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

B Failure to observe this may result in fire or electric shocks.

Do not place liquid containers on top of the projector.

B If water spills onto the projector or gets inside it, fire or electric shocks

could result.

B If any water gets inside the projector, contact an Authorized Service

Center.

Do not insert any foreign objects into the projector.

B Do not insert any metal objects or flammable objects into the projector or

drop them onto the projector, as doing so can result in fire or electric
shocks.

Keep the batteries out of the reach of infants.

B If the batteries are swallowed, death by suffocation may result. If you

believe that the batteries may have been swallowed, seek medical advice
immediately.

Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.

B Failure to observe this may cause the batteries to leak, overheat, explode

or catch fire.

B Store the batteries in a plastic bag and keep them away from metallic

objects.

During a thunderstorm, do not touch the projector or the cable.

B Electric shocks can result.

Do not use the projector in a bath or shower.

B Fire or electric shocks can result.

Do not look into the lens while the projector is being used.

B Strong light is emitted from the projector’s lens. If you look directly into this

light, it can hurt and damage your eyes.

B Be especially careful not to let young children look into the lens. In

addition, turn off the power and disconnect the power cord plug when you
are away from the projector.

Do not place your hands or other objects close to the air outlet port.

B Heated air comes out of the air outlet port. Do not place your hands or

face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.

Replacement of the lamp unit should only be carried out by a qualified
technician.

B The lamp unit has high internal pressure. If improperly handled, explosion

might result.

B The lamp unit can easily become damaged if struck against hard objects

or dropped, and injury or malfunctions may result.

When replacing the lamp, allow it to cool for at least one hour before
handling it.

B The lamp cover gets very hot, and touching it can cause burns.

Before replacing the lamp, be sure to disconnect the power cord plug
from the wall outlet.

B Electric shocks or explosions can result if this is not done.

Caution

Do not cover the air inlet port or the air outlet port.

B Doing so may cause the projector to overheat, which can cause fire or

damage to the projector.

B Do not place the projector in narrow, badly ventilated places such as

closets or bookshelves.

Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.

B Using the projector under such conditions may result in fire or electric shocks.

When disconnecting the power cord, hold the plug, not the cord.

B If the power cord itself is pulled, the cord will become damaged, and fire,

short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

B Moving the projector with cables still attached can damage the cables,

which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

B Failure to observe this may cause the projector to become unbalanced

and fall, which could result in damage or injury.

ENGLISH-9

Preparation

8-ENGLISH

Accessories

Check that all of the accessories shown below have been included with your
projector.

Remote control unit
(N2QAEA000025 x1)

Video cable
[3.0 m (9´10˝),
K2KA2FA00003 x1]

AAA batteries for
remote control unit (x2)

Before use

Cautions regarding setting-up

Avoid setting up in places which are subject to vibration or shocks.

The internal parts can be damaged, which may cause malfunctions or
accidents.

Do not set up the projector near high-voltage power lines or near
motors.

The projector may be subject to electromagnetic interference.

If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.

You will need to purchase the separate installation kit (Model No.ET-PKE700).
Furthermore, all installation work should only be carried out by a qualified
technician.

If using this projector at high elevations (above 1 400 m), set the “FAN
CONTROL” to “HIGH”. (Refer to page 47.)

Failure to observe this may result in malfunctions.

Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.

B Failure to observe this may cause the batteries to overheat, leak, explode

or catch fire, and burns or other injury may result.

When inserting the batteries, make sure the polarities (+ and -) are
correct.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area
may result.

Use only the specified batteries.

B If incorrect batteries are used, they may explode or leak, and fire, injury or

contamination of the battery compartment and surrounding area may
result.

Do not mix old and new batteries.

B If the batteries are inserted incorrectly, they may explode or leak, and fire,

injury or contamination of the battery compartment and surrounding area
may result.

Do not put your weight on this projector.

B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children stand or sit on the projector.

Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.

B Electric shocks can result if this is not done.

Ask an Authorized Service Center to clean inside the projector at least
once a year.

B If dust is left to build up inside the projector without being cleaned out, it

can result in fire or problems with operation.

B It is a good idea to clean the inside of the projector before the season for

humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.

We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company.

NOTICE:

B This product has a High Intensity Discharge (HID) lamp that contains a

small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>

Power cord
(K2CG3FR00001 x 1)

ENGLISH-11

Preparation

10-ENGLISH

Notes on use

In order to get the best picture quality

Draw curtains or blinds over any windows and turn off any lights near the
screen to prevent outside light or light from indoor lamps from shining onto
the screen.

Do not touch the surfaces of the lens with your bare hands.

If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the lens cover.

Screen

Do not apply any volatile substances which may cause discoloration to the
screen, and do not let it become dirty or damaged.

Lamp

The lamp may need to be replaced earlier due to variables such as individual
lamp characteristics, usage conditions and the installation environment,
especially when the projector is subjected to continuous use for more than
10 hours or the power is frequently turned on and off.

Liquid crystal panel

B Do not project the same image for long periods of time, as this may remain

as an afterimage on the liquid crystal panel.

B The liquid crystal panel of the projector is built with very high precision

technology to provide fine picture details. Occasionally, a few non-active
pixels may appear on the screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your LCD.

Location and function of each part

# Projector control panel (page 14)
$ Zoom ring (page 25)
% Focus ring (page 25)
& Projection lens
' Air inlet port

Do not cover this port.

( Air filter (page 50)
) Shift lever (page 25)

This lever adjusts the lens direction.

* Front adjustable legs (L/R) (page 25)
+ Lens cover
, Remote control signal receptor (page 23)

- Air outlet port

Do not cover this port.

WARNING

Do not place your hands or other objects close to the air outlet port.

B Heated air comes out of the air outlet port. Do not place your hands or

face, or objects which cannot withstand heat close to this port, otherwise
burns or damage could result.

Projector <Top, right and front>

% ˛&$

'

˛(

#

˛*
˛,

˛+ ˛* ˛)

˛-

12-ENGLISH ENGLISH-13

Preparation

Connector panel

#$ % &'(

# TRIGGER connector (pages 20, 21 and 22)

This connector outputs 12 V when the power is turned on. Connect this
connector to equipment such as an electric screen.

$ HDMI IN connector (page 21)

This connector is used to input HDMI signals.

% PC IN (RGB input) connector (page 22)

This connector is used to input RGB signals from a PC.

& S-VIDEO IN connector (page 20)

This connector is used to input signals from an S-VIDEO-compatible
equipment such as a video deck.

' VIDEO IN connector (page 20)

This connector is used to input video signals from a video equipment such
as a video deck.

( COMPONENT IN [YPBPR(CBCR) input] connectors (page 20)

These connectors are used to input YPBPR signals from compatible
equipment such as a DVD player.

# Connector panel (page 13)
$ Air inlet port

Do not cover this port.

% Power input socket (AC IN) (page 24)

The accessory power cord is connected here.
Do not use any power cord other than the accessory power cord.

& Security lock

This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.

' Lamp unit cover (page 51)
( MAIN POWER switch (pages 24 and 26)

Projector <Back and bottom>

#$˛%

(

'

&

ENGLISH-15

Preparation

14-ENGLISH

*)( '

#%&$

)

(
&

*

.
/

'

-

2

1

+

0

,

Projector control panel

Remote control unit

# Power indicator (pages 24, 26 and 27)

This indicator illuminates red when the main power is switched on (standby
mode), and it illuminates green when a picture starts to be projected.

$ LAMP indicator (page 49)

This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.

% TEMP indicator (page 48)

This indicator illuminates if an abnormally high temperature is detected
inside the projector. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash.

& Arrow (FF, GG, IIand HH) buttons (page 38)

These buttons are used to select and adjust items in the on-screen menus.

' ENTER button (page 38)

This button is used to accept and to activate items selected in the
on-screen menus.

( MENU button (page 36)

This button is used to display the “MAIN MENU”. When a menu screen is being
displayed, it can be used to return to a previous screen or to clear the screen.

) INPUT select buttons (page 25)

These buttons are used to switch the input signals from the connected equipment.

* POWER button (pages 24 and 26)
+ LIGHT button (page 29)

This button is used to illuminate the buttons on the remote control unit.

, KEYSTONE button (page 28)

This button is used to correct keystone distortion of the projected image
when the projector position is tilted upward or downward.

- FREEZE button (page 28)

This button is used to momentarily freeze projection so that a still picture is
displayed.

. PICTURE MODE button (page 29)

Pressing this button will change the picture mode.

/ USER MEMORY button (page 35)

This button is used to display the “MEMORY LOAD” menu.

0 COLOR MANAGEMENT button (page 32)

This button is used to display the “COLOR MNGMT” menu.

1 ASPECT button (page 30)

This button is used for aspect adjustment (vertical and horizontal
proportions).

2 NORMAL button (page 39)

This button is used to reset the projector adjustment values to the factory
default settings.

ENGLISH-17

Projection distances

NOTE:

B The dimensions in the table above are approximate.
B For details about projected image distances, refer to page 60.

Getting started

Setting-up

Projection methods

In way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION” menu. Refer
to page 47 for details.)

BFront-desk projection BFront-ceiling projection

BRear-desk projection

(Using a translucent screen)

BRear-ceiling projection

(Using a translucent screen)

Menu items Setting

FRONT

DESK

FRONT/REAR

DESK/CEILING

Menu items Setting

FRONT

CEILING

FRONT/REAR

DESK/CEILING

Menu items Setting

REAR

DESK

FRONT/REAR

DESK/CEILING

Menu items Setting

REAR

CEILING

FRONT/REAR

DESK/CEILING

NOTE:

B You will need to purchase the separate ceiling bracket (ET-PKE700)

when using the ceiling installation method.

B If you set up the projector vertically, it may cause

damage to the projector.

B It is recommended that you set up the projector

in a place that is tilted at less than

±30°. Setting

up the projector in places that are tilted at more
than

±30° may cause malfunctions.

16-ENGLISH

L

SW

82.9 mm

(3-1/4˝)

L

SH

Projector position

L: Projection distance
SH: Image height
SW:Image width

Screen

1.01 m(40˝) 0.50 m(1´7˝) 0.89 m(2´11˝) 1.2 m(3´11˝) 2.4 m(7´10˝)

1.27 m(50˝) 0.62 m(2´) 1.11 m(3´7˝) 1.5 m(4´11˝) 3.0 m(9´10˝)

1.52 m(60˝) 0.75 m(2´5˝) 1.33 m(4´4˝) 1.8 m(5´10˝) 3.7 m(12´1˝)

1.77 m(70˝) 0.87 m(2´10˝) 1.55 m(5´1˝) 2.1 m(6´10˝) 4.3 m(14´1˝)

2.03 m(80˝) 1.00 m(3´3˝) 1.77 m(5´9˝) 2.4 m(7´10˝) 4.9 m(16´)

2.28 m(90˝) 1.12 m(3´8˝) 1.99 m(6´6˝) 2.7 m(8´10˝) 5.5 m(18´)

2.54 m(100˝) 1.24 m(4´) 2.21 m(7´3˝) 3.1 m(10´2˝) 6.2 m(20´4˝)

3.05 m(120˝) 1.49 m(4´10˝) 2.66 m(8´8˝) 3.7 m(12´1˝) 7.4 m(24´3˝)

3.81 m(150˝)

5.08 m(200˝)

1.87 m(6´1˝)

2.49 m(8´2˝)

3.32 m(10´10˝)

4.43 m(14´6˝)

4.6 m(15´1˝)

6.2 m(20´4˝)

9.3 m(30´6˝)

12.4 m(40´8˝)

Screen size (16:9)

Diagonal

length

Height

(SH)

Width

(SW)

Projection distance (L)

Wide
(LW)

Telephoto

(LT)

Screen

ENGLISH-19

Getting started

18-ENGLISH

Setting up range using the lens shift function

This projector can be placed in various places by controlling the shift lever at
the front side of the projector to move the lens in order to adjust the position
of the projected image.

BHorizontal lens shift

BVertical lens shift

About 25% of the
screen (maximum)

About 25% of the
screen (maximum)

About 63% of

the screen

(maximum)

About 63% of

the screen

(maximum)

When shift lever is moved

to the left (full)

When shift lever is moved
to the right (full)

When shift lever is
moved down (full)

When shift lever is
moved up (full)

Screen

Screen

* The values in the table are for the width and

the height of the screen.

NOTE:

B Turn the shift lever right to secure the shift lever.
B When the lens has been shifted fully to the right or left, you will not be

able to shift the lens up or down.
When the lens has been shifted fully up or down, you will not be able to
shift the lens to the right or left.

B Generally, the maximum picture quality is obtained when the lens is

moved to the center (horizontally and vertically).

Vertical (V)

About 63%

About 50%

About 30%

About 10%

About 0%

Horizontal (H)

About 0%

About 8%

About 17%

About 23%

About 25%

V

H

BSetting up range

Projector

Screen

Projector set up range
(center of the lens)