Installation
Instructions
Outdoor Domed Housings
PODC240/PODCW240
Manufactured By:
Before attempting to connect or operate this product,
please read these instructions completely.
for
1. Read Instructions - All the safety and operating instructions
!
should be read before the unit is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the unit and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions
should be followed.
5. Electrical Connections - Only a qualified electrician should
make electrical connections.
6. Attachments - Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible
distance.
8. Mounting - This unit must be properly and securely mounted
to a supporting structure capable of sustaining the weight
of the unit. Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local
codes.
c. Care should be exercised to select suitable hardware to
install the unit, taking into account both the composition
of the mounting surface and the weight of the unit. Be
sure to periodically examine the unit and the supporting
structure to make sure that the integrity of the installation
is intact. Failure to comply with the foregoing could
result in the unit separating from the support structure
and falling, with resultant damages or injury to anyone
or anything struck by the falling unit.
SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS
CAUTION
RISK OF
ELECTRIC SHOCK!
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
!
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper.
DO NOT OPEN COVER.
NO USER SERVICEABLE PARTS INSIDE.
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
ONE-YEAR LIMITED WARRANTY
Videolarm, Incorporated warrants that products sold
hereunder shall be fit for the ordinary purpose for which
said products are intended and shall be free from defects
in material and workmanship for a period of one year from
date of sale to buyer. Note that all electrical components
will be warranted for a period of 1 year from date of sale to
buyer. Videolarm makes no other warranty of any kind with
respect to this product, whether expressed or implied,
including, without limitation, the implied warranty of fitness
for a particular purpose.
In the event of a breach of the above warranty, Videolarm
shall, at its option, repair or replace said product. This is
Videolarm's sole obligation under this warranty. In no event
shall Videolarm be liable for any incidental or consequential
damages, as defined in section 2-715 of the Uniform
Commercial Code by a breach of this warranty.
Videolarm shall repair or replace defective products
upon shipment of products prepaid to Videolarm, Inc.,
2525 Park Central Blvd., Decatur, GA 30035.
Repairs made necessary by reason of accident, misuse
or normal wear shall be charged at Videolarm's standard
rate. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Be sure to save:
1. The shipping carton and packaging material. They are the
safest material in which to make future shipments of the
equipment.
2. These Installation and Operating Instructions.
SERVICE
If the unit ever needs repair service, the customer should
contact Videolarm (1-800-554-1124) for authorization to
return and shipping instructions.
TECHNICAL SUPPORT
If technical support is needed, Videolarm has set-up a 24
hour technical support line for their customers.
24 HOUR TECHNICAL SUPPORT
1-800-554-1124
TABLE OF CONTENTS
• CAUTION
1. PRECAUTIONS ON INSTALLATION
2. DESCRIPTION
3. INSTALLATION
3-1 Camera Installation
3-2 Dome Assembly
3-3 Wall Mount Bracket Installation
3-4 Dome Installation
3-5 Care and Maintenance
4. SYSTEM CONNECTION
5. SPECIFICATIONS
DESCRIPTION
• This product has been designed and engineered for the combination camera WV - CS600 and WV-CS400
for ease of installation and service.
• This product is a discreet outdoor housing designed for pendant (PODC240) or wall mount (PODCW240)
applications.
Check all contents before beginning installation.
A. Housing Assembly (PODC240) Housing Assembly (PODCW240)
1. 2 1/4" Coupling w/ 2 set screws 1. Wall Mount Bracket
2. Coupling Gasket 2. Housing Gasket
3. Housing Mounting Bracket 3. White Upper Top
4. Housing Gasket
5. White Upper Top
B. Bracket Assembly
1. Upper Housing Bracket
2. Lower Housing Bracket
3. 24 VDC Blower
4. 24 VAC Heater
5. PC Board Assembly
C. Dome Assembly
1. 7" Clear Plastic Dome
2. (3) Security Fasteners
D. Housing Packet
1. Security Tool
2. (4) 8 x 32 Bolts
3. (2) Molex Connector w/ 6 Pins
4. Instruction Manual
5. 1/4" x 20 x 1/2" Bolt
6. 1/4" Flat Washer
7. 1/4" Lock Washer
8. Plastic Lanyard
- 3 -
Housing Assembly
Bracket Assembly
2 1/4" Coupling*
Mounting Bracket*
Top Gasket
Housing top
Upper Housing Bracket
Dome Assembly
Lower Housing Bracket
Camera
7" Clear Dome
* Or Wall Mount
- 4 -
-3. INSTALLATION
3-1 Camera Installations
Using a long nose pliers, snap out the area marked "X"
from the unitized camera. This will allow the cables
to exit.
Note: Use a file to round off all sharp edges.
Connect the power cable and video cable lines.
Loop excess cables through the cable clamp.
"X"
Attach the camera mount bracket of the unitized
camera to the dome bracket, using the standard
screw (A).
Camera Mount Bracket
Attach the unitized camera to the dome assembly.
Be sure to hang the safety wire to the assembly first.
Then attach the safety screw to the camera mount
bracket, using the standard screw (s).
Standard
Screw A
Connect
3-2 Dome Assembly
Use the black handle security tool to attach the
dome to the housing.
3-3 Wall Mount Bracket Installation
Note: Mounting hardware not included. Care should
be exercised to select suitable hardware to
mount the unit.
Safety Screw
Safety Wire
Compatible brackets for PODC240/PODCW240:
• Parapet Mount Bracket - PSRCW-2000
• Corner Mount Bracket - PCA-2
• Pole Mount Bracket - PPM-3
- 5 -
Assemble the power cable with the provided
connector.
3-4 Pendant PODC240- Connections
Attach coupling to 1 1/2 NPT thread pipe.
Note: Seal thread with a bead of silicone sealer to
ensure water-tight fit.
3
1
Connector Information Pin
1. AC 240 VAC Live
2. AC 240 VAC Neutral
3. Ground
4. Not Used
CAUTION: For lightning protection of the camera
and heater/blower, pin 3 of the
connector must be connected to real
electrical ground.
CONNECT THIS TO A 240 VAC POWER
SOURCE.
!
WARNING: A READILY ACCESSIBLE
DISCONNECT DEVICE SHALL BE
INCORPORATED IN THE FIXED
WIRING.
Input Power Requirement
230VAC, 50Hz, .3 amp
4
2
Connect the power cable and video cable lines.
Wire hook can be used as temporary support.
Connect
Wires
Attach dome assembly to coupling. Secure screws
(C).
OPERATING DISTANCES
Awg Size Impedance Max Distance
Awg #14 2.73 ohm/1000 ft. 4000 ft.
Awg #16 4.35 ohm/1000 ft. 2500 ft.
Awg #18 6.92 ohm/1000 ft. 1600 ft.
- 6 -
Wire Hook
Secure C
Secure safety screw (D) to housing mounting bracket
with plane washer (G) and lock washer (F).
G F D
3-5 Care and Maintenance
WARNING: Hazardous voltage within
this unit. Disconnect power to the unit
from the building fixed wiring disconnect device before perfomrming the
following maintenance procedures.
4. System Connection
Example 1: Connect the coaxial cable between the
video output connector on the WV-CS404 and the
camera input connector on the WV-CU101.
Video Monitor
• The lower dome is an optical surface. When
cleaning the inner surface of the dome, handle
with extreme care.
• If debris and dust accumulates on the dome's
inner surface, remove with clean air pressure.
Compressed air cans are available for this use at
most photography supply stores.
• If the surface doesn't clean properly with
compressed air, use a nonabrasive cleaner that is
acceptable for use on acrylic. Do not use any
other type of cleaner. This may result in scratches
to the dome's surface.
CAUTION: When using approved
acrylic cleaner make sure all surfaces
are dry before reapplying power to
the unit.
WV-CU101
Example 2: Connect the coaxial cable between the
video output connector on the WV-CS400 and the
camera input connector on the WV-CU254.
Note: For the connections in the diagram, refer to
the operating instructions for each product.
WV-CS600
- 7 -
Example 3: Connect the coaxial cable between
the video output connector on the WV-CS400,
WV-CS600 and the camera input connector on the
WV-CU254.
SPECIFICATIONS
MECHANICAL/ELECTRICAL
Upper Housing - .25" high impact, UV-stable white plastic
Housing Bracket - 14- and 16-gauge steel
Lower Dome - 7" distortion-free acrylic
Unit Weight - Camera 4.4 lbs.; domed housing 6.6 lbs.
Environmental - -28°C to 54°C
Heater - On at 4°C, off at 16°C (+/-5°) 60 vA
Blower - 115 VAC 5 Watts
Surge Protector:
Video clamping - Differential mode 24-36V
common mode 54-72 V
STANDARD CONFIGURATION
Item or Sub-Item Description
20-DCPOD7 7" CLEAR DOME POD7
21-TOPOD7 HOUSING TOP FOR POD7
30-VL1372 UPPER HOUSING BRACKET, POD-7C
30-VL1379 LANYARD ,7" DOMES
30-VL917 POD-12C 2 1/4" COUPLING
30-VL926 POD12C MOUNTING BRACKET
40-BRPOD7 BRACKET ASSY POD7
30-VL1371 LOWER HOUSING BRACKET, POD-7C
60-WPBNC1 BNC PLUG 75 OHM FOR RG 179
70-WPMX01 WM3701 (4) CIR/PLUG
70-WPMX02 Molex 39-00-0039 FEMALE PIN
71-BLEH220 BLOWER, 115 VAC 60MM
72-HTPOD7X 50 WATT 220 VAC HEATER, POD-7C
76-POD7C240 PCB PODC240
90-BTRP19 8-32 X 3/8 RD HD PHIL SS
91-NTHH06 8-32 HEX NUT SS
92-WSTH02 #8 EXT TTH STAR L/W STAINLESS
94-FSCT01 CABLE TIE NYLON NAT.
94-FSSR03 HEYCO 1060 SR 2M-1 BLK STRAIN
95-MX2025 MOLEX RECEPTACLE
95-PCST02 TTW FASTEX PCB SUPPORTS
95-PCST03 ITW FASTEX 232-120207-30
40-CAPOD701 COAXIAL CABLE ASSY. FOR POD7
40-CAPOD702 POD-12C CABLE ASSY. B
40-PKPOD7 PACKET ASSY FOR POD7C
70-WPMX10 Molex 39-01-4030
90-BTHH32 1/4-20 X 1/2" HX HD SS MS
90-BTHH39 1/4-20 x 3/8" HX HD SS MS
90-BTSS05 1/4-20 x 1/2" SET SCREW
92-WSFL01 1/4 SAE FLAT WASHER 18-8 SS
92-WSSL01 1/4 SPLIT LOCKWASHER 18-8 SS
94-FSLG01 HEYCO WIRE HOLDER #3630 WT
94-FSRT01 RETAINER BLACK NYLON
95-FSSL03 HOOK LOOP CABLE POD12C
95-FSSL04 CABLE FERRULES
95-FSTS03 TOOLHEAD SCREW
96-PSGK04 VL-1433 POD-12C TOP GASKET
96-PSGK05 VL-1014 POD-12C BOTTOM GASKET
- 8 -
3.432" (8.17cm)
14.169" (35.99cm)
7.0" (17.78cm)
9.169" (23.29cm)
1.405" (3.56cm)
2.084"
(7.21cm)
12.861" (32.67cm)
7.0" (17.78cm)
Gasket
Set Screws
Coupling for 1 1/2" standard pipe
Slot safety screw
(located on both sides)
Rev. # 3052/1299
- 9 -
Loading...