Panasonic PN28480K-SG, PN28160K, PN28240K, PN28240K-ID, PN28480K Operation Manual

...

 Thank you for purchasing our product.  This manual provides important information about safe and proper

operations of this Switching Hub.

 Please read the "Important Safety Warnings" on pages 3 to 4.  Any problems or damage resulting from disassembly of this Switching Hub

by customers are note covered by the warranty.

 Applicable product names and model numbers are described on page 2.

Layer 2 Switching Hub

Model Number: PN28080K/PN28160K

PN28240K/PN28480K

Operation Manual

for CLI

This operation manual is applicable to the following Switching Hubs:

Product name

Model No.

Firmware version

Switch-M48eG

PN28480K-ID

PN28480K-TH

PN28480K-MY

PN28480K-SG

2.0.1.05 or higher

Switch-M24eG

PN28240K-ID

PN28240K-TH

PN28240K-MY

PN28240K-SG

2.0.1.05 or higher

Switch-M16eG

PN28160K-ID

PN28160K-TH

PN28160K-MY

PN28160K-SG

2.0.1.05 or higher

Switch-M8eG

PN28080K-ID

PN28080K-TH

PN28080K-MY

PN28080K-SG

2.0.1.05 or higher

Important Safety Instructions

This chapter contains important safety instructions for preventing bodily injury and/or property damage. You are required to follow them.  Severity of bodily injury and/or property damage, which could result from

incorrect use of the Switching Hub, are explained below.

 The following symbols are used to classify and describe the type of

instructions to be observed.

This symbol is used to alert users to what they must not do.

 Do not use power supply other than AC 100 - 240V.

Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not handle the power cord with wet hand.

Deviation could lead to electric shock and/or equipment failure.

 Do not handle this Switching Hub and connection cables during a

thunderstorm. Deviation could lead to electric shock.

 Do not disassemble and/or modify this Switching Hub.

Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not damage the power cord. Do not bend too tightly, stretch,

twist, bundle with other cord, pinch, put under a heavy object, and/or heat it. Damaged power cord could lead to fire, short, and/or electric shock.

 Do not put foreign objects (such as metal and combustible) into the

opening (such as twisted pair port, console port, SFP extension slot), and/or do not drop them into the inside of the Switching Hub. Deviation could lead to fire, electric shock, and/or equipment failure.

This symbol indicates safety instructions. Deviation from these instructions could lead to bodily injury and/or property damage.

This symbol is used to alert

users to what they must do.

WARNING

This symbol indicates a potential hazard that could result in serious injury or death.

CAUTION

WARNING

 Do not connect equipment other than

10BASE-T/100BASE-TX/1000BASE-T to twisted pair port. Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not place this Switching Hub in harsh environment (such as near

water, high humid, and/or high dust). Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not place this Switching Hub under direct sun light and/or high

temperature. Deviation could lead to high internal temperature and fire.

 Do not install this Switching Hub at the location with continuous

vibration or strong shock, or at the unstable location. Deviation could lead to injury and/or equipment failure.

 Do not install any module other than the separately sold SFP module

(PN54021K/PN54023K) to SFP extension slot. Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not put this Switching Hub into fire.

Deviation could lead to explosion and/or fire.

 Do not use the supplied power cord for anything other than this

product. Deviation could lead to fire, electric shock, and/or equipment failure.

 Do not place this Switching Hub under direct sun light and or high

temperature. Deviation could lead to fire to high internal temperature and fire.

WARNING

 Use the bundled power cord (AC 100 – 240V specifications).

Deviation could lead to electric shock, malfunction, and/or equipment failure.

 Unplug the power cord in case of equipment failure.

Deviation, such as keeping connected for a long time, could lead to fire.

 Connect this Switching Hub to ground.

Deviation could lead to electric shock, malfunction, and/or equipment failure.

 Connect the power cord firmly to the power port.

Deviation could lead to electric fire, shock, and/or malfunction.

 Unplug the power cord if the STATUS/ECO LED (Status/ECO mode)

blinks in orange (system fault). Deviation, such as keeping connected for a long time, could lead to fire.

 When this Switching Hub is installed on wall surface, mount it firmly so

as not to drop down because of weight of the main body and connection cable. Deviation, could lead to injury and/or equipment failure.

 Handle the Switching Hub carefully so that fingers or hands may not

be damaged by twisted pair port, SFP extension slot, console port, or power cord hook block.

WARNING

CAUTION

Basic Instructions for the Use of This

Product

 For inspection and/or repair, consult the shop.

 Use commercial power supply from a wall socket, which is close and easily

accessible to this Switching Hub.

 Unplug the power cord when installing or moving this Switching Hub.

 Unplug the power cord when cleaning this Switching Hub.

 Use this Switching Hub within the specifications. Deviation could lead to

malfunction.

 When connecting a cable, hold the Switching Hub firmly.

 Do not put a floppy disk or a magnetic card near the rubber feet (with built-in

magnets). Otherwise, recorded content may be lost.

 After installing this Switching Hub on an OA desk, do not move either without

dismounting it. Otherwise, the desk surface may be damaged.

 Do not touch the metal terminal of the RJ45 connector, the modular plug of

connected twisted pair cable, or the metal terminal of the SFP extension slot. Do not place charged objects in the proximity of them. Static electricity could lead to equipment failure.

 Do not put the modular plug of the connected twisted pair cable on objects

that can carry static charge, such as carpet. Do not place it in the proximity. Static electricity could lead to equipment failure.

 Do not put a strong shock, including dropping, to this Switching Hub.

Deviation could lead to equipment failure.

 Before connecting a console cable to the console port, discharge static

electricity, for example by touching metal appliance (do not discharge by touching this Switching Hub).

 Do not store and/or use this Switching Hub in the environment with the

characteristics listed below. (Store and/or use this Switching Hub in the environment in accordance with the specification.)

- High humidity. Possible spilled liquid (water).

- Dusty. Possible static charge (such as carpet).

- Under direct sunlight.

- Possible condensation. High/low temperature exceeding the specifications environment.

- Strong vibration and/or strong shock.

 Please use this Switching Hub in place where ambient temperature is from 0

to 50C.

Failure to meet the above conditions may result in fire, electric shock, breakdown, and/or malfunction. Please take notice because such cases are out of guarantee. Additionally, do not cover the bent hole of this Switching Hub. Deviation could lead to high internal temperature, equipment failure and/or malfunction.

 When stacking Switching Hubs, leave a minimum of 20 mm space between

them.

 Operation is not guaranteed if a module other than the optional SFP

extension modules (PN54021K/PN54023K) is inserted into the SFP extension slot. For the latest information about compatible SFP extension modules, check our website.

1. Panasonic will not be liable for any damage resulting from the operation not in accordance with this document or the loss of communications, which may or may not be caused by failure and/or malfunction of this product.

2. The contents described in this document may be changed without prior notice.

3. For any question, please contact the shop where you purchased the product.

* Brands and product names in this document are trademarks or registered

trademarks of their respective holders.

Table of Contents

Important Safety Instructions ................................................................................ 3

Basic Instructions for the Use of This Product ....................................................... 6

1. Command Hierarchy ...................................................................................... 10

2. Basic Information Display .............................................................................. 14

3. Basic Switch Configuration ............................................................................ 23

3.1. System Administration Configuration ..................................................... 23

3.1.1. Username and Password Configuration ............................................ 31

3.2. IP Address Configuration ......................................................................... 34

3.3. SNMP Configuration ................................................................................ 43

3.4. Port Configuration ................................................................................... 77

3.5. System Security Configuration ................................................................ 95

3.5.1. Console Configuration ..................................................................... 100

3.5.2. Telnet Configuration ........................................................................ 105

3.5.3. SSH Configuration ............................................................................ 114

3.5.4. Web Configuration .......................................................................... 122

3.5.5. RADIUS Server Configuration .......................................................... 127

3.5.6. Configuration of the Easy IP Address Setup Function .................... 137

3.5.7. Configuration of the Syslog Transmission Function ........................ 142

3.6. MAC Address Table Display, Registration, and Configuration ............. 147

3.7. Time Configuration ................................................................................ 159

3.8. ARP Configuration ................................................................................. 170

4. Advanced Switch Configuration ................................................................. 176

4.1. VLAN Configuration .............................................................................. 176

4.1.1. Internet Mansion Function Configuration ...................................... 189

4.2. Link Aggregation Configuration ........................................................... 195

4.2.1. About Link Aggregation .................................................................. 195

4.3. Port Monitoring Configuration ............................................................. 201

4.4. Access Control Configuration ................................................................ 206

4.5. QoS (Quality of Service) Configuration ................................................. 230

4.6. Bandwidth Control Configuration ......................................................... 237

4.7. Storm Control Configuration ................................................................. 242

4.8. Authentication Function Configuration ................................................ 250

4.9. AAA Configuration ................................................................................ 263

4.10. Authentication Log Configuration ...................................................... 273

4.11. IEEE802.1X Port-Based Authentication Configuration ....................... 279

4.12. IEEE802.1X MAC-Based Authentication Configuration ...................... 298

4.13. MAC Authentication Configuration .................................................... 319

4.14. WEB Authentication Configuration .................................................... 333

4.8. LED Base Mode Configuration .............................................................. 359

4.9. Line Configuration ................................................................................. 364

4.9.1. Loop Detection Configuration ......................................................... 364

4.9.2. Configuration of MNO Series Power Saving Mode ......................... 371

4.9.3. Line Configuration Display ............................................................... 374

4.10. Port Group Configuration ............................................................ 377

5. Statistical Information Display .................................................................... 384

.......................................................................... 390 6. Configuration File Transfer

....................................................................................... 393 7. Firmware Upgrade

......................................................................................................... 396 8. Reboot

8.1. Normal Reboot ....................................................................................... 396

8.2. Restoration to Factory Default Settings ................................................ 399

8.3. Reboot Timer Configuration .................................................................. 402

9. Ping Execution ............................................................................................. 405

.................................................................................... 408 10. System Log Display

....................................... 419 11. Save and Display of Configuration Information

................................................ 424 12. Obtaining Technical Support Information

Appendix A. Specifications ................................................................................. 427

Appendix B. Easy IP Address Setup Function ................................................... 428

Appendix C. Example of Network Configuration using Loop Detection Function

and Its Precautions ....................................................................... 429

Appendix D. MIB List .......................................................................................... 431

Troubleshooting ................................................................................................. 436

After-sales Service ............................................................................................... 437

1. Command Hierarchy

There are four levels in the hierarchy.

(1) User mode:

This is the default mode after login. Limited operations are allowed.

(2) Privileged mode:

This mode allows you to check the state of the Switching Hub, to edit configuration files, etc.

(3) Global configuration mode:

This mode allows you to set the general configuration of the Switching Hub.

(4) Interface configuration mode:

This mode allows you to set individual items, such as each port and each VLAN, in details.

Fig. 1-1 Command hierarchy

enable Command

• Enter this command to switch from the User mode to the Privileged mode. M24eG> ···················· User mode M24eG> enable ·············· User mode  Privileged mode M24eG# ···················· Privileged mode M24eG# disable ·············· Privileged mode  User mode M24eG> ···················· User mode

disable Command

• Enter this command to switch from the Privileged mode to the User mode. M24eG# ···················· Privileged mode M24eG# disable ·············· Privileged mode  User mode M24eG> ···················· User mode

M24eG> enable M24eG# configure M24eG(config)# interface gi0/1 M24eG(config-if)# exit M24eG(config)# exit M24eG#

configure Command

• Enter this command to switch from the Privileged mode to the Global

configuration mode. M24eG# ····················· Privileged mode M24eG# configure ············ Privileged mode

 Global configuration mode

M24eG(config)# ·············· Global configuration mode

interface Command

• Enter this command to switch from the Global configuration mode to the

Interface configuration mode. M24eG(config)# ·············· Global configuration mode M24eG(config)# interface vlan1 ·· Global configuration mode

 Interface

configuration mode (vlan1)

M24eG(config-if)# exit ········· Interface configuration mode

 Global configuration mode

M24eG(config)# interface Gigabitethernet0/1

········· Global configuration mode  Interface

configuration mode (interface1)

M24eG(config-if)# exit ········· Interface configuration mode

 Global configuration mode

M24eG(config)# ·············· Global configuration mode

exit Command

• Enter this command to return to the previous mode. M24eG(config-if)# exit ········· Interface configuration mode

 Global configuration mode

M24eG(config)# exit ··········· Global configuration mode

 Privileged mode

M24eG# exit ·················· Privileged mode  User mode M24eG> ····················· User mode

end Command

• Enter this command to switch from configuration modes to the Privileged

mode.

M24eG(config-if)# end ········ Interface configuration mode

 Privileged mode

M24eG# configure M24eG(config)# end ·········· Global configuration mode

 Privileged mode

logout Command

• Enter this command to return to the menu screen from any command mode.

M24eG(config)# logout ······· Configuration mode  Menu

? Command

• Enter a question mark (?) to view available commands in that command

mode.

Fig. 1-2 ? command

Command History Support

• Press the  (up arrow) key to view the history of the entered commands.

M24eG> ? enable Privilege level to go to. exit Exit from current mode logout To logout from the CLI shell ping Send ICMP ECHO_REQUEST to network hosts

M24eG>

Command-line Completion Support

• Enter a question mark (?) immediately after a command. This will show command candidates to complete the entered command.

Fig. 1-3 Command-line completion support

Abbreviated Command Entry After entering just enough characters of a command or an argument to identify it uniquely, you can omit the rest of the command or the argument.

[Example of Abbreviated Command Entry]

 enable  en  show running-config  sh ru

[Bad Example of Abbreviated Command Entry]  co  Because both "configure" and "copy" are possible, an error occurs.

Symbols used in the command description are as follows:

< > : Required - You must enter this. { | } : Selections - Select one from the selections. [ ] : Option - Enter as required.

Commands are case sensitive. Uppercase and lower case letters are treated as different letters.

Note that in this manual, ports are specified for Switch-M24eG (24 ports) except for a few commands. When entering a command, make sure to specify existing port numbers of your switch.

M24eG# configure M24eG(config)# ip address ? <ip-address> ex: 192.168.1.1

M24eG(config)# ip address

2. Basic Information Display

Enter the commands listed below in the "Privileged mode" to show this Switching Hub's basic information.

Command to show the system information (up time and version information)

M24eG#

show sys-info

Command to show the address information (MAC address and IP address information)

M24eG#

show ip conf

Command to show the ipv6 address information (MAC address and IPv6 address information)

M24eG#

show ipv6 conf

An example of executing the command to show the system information is shown below.

Fig. 2-1 Example of executing the command to show the system information

(1) System up for

Shows the Switching Hub's up duration in days and time.

(2) Boot Code Version

Shows the Switching Hub's boot code version.

(3) Runtime Code Version

Shows the Switching Hub's firmware version.

(4) Hardware Information

Shows the Switching Hub's hardware information.

M24eG> enable M24eG# show sys-info

System up for : 0 days, 0:1:29 Boot Code Version : 1.00.17 Runtime Code Version : 1.0.0.07

Hardware Information Version : A1 DRAM Size : 128MB Fixed Baud Rate : 9600bps FLASH Size : 32MB

Administration Information Switch Name : Switch Location : Switch Contact :

System Address Information MAC Address : 00:C0:8F:A0:13:98 IP Address : 0.0.0.0 Subnet Mask : 0.0.0.0 Default Gateway : 0.0.0.0

System Address Information IPv6 Status : Disable MAC Address : 00:C0:8F:A0:13:98 IPv6 Address/prefixlen : ::/128 IPv6 Link Local Address : :: IPv6 Default Gateway : ::

M24eG#

(1)

(2)

(3)

(4)

(9)

(14)

(4)

(6)

(7)

(4)

(5)

(8)

(4)

(5)

(13)

(10)

(11)

(12)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(5) Version

Shows the Switching Hub's hardware version.

(6) DRAM Size

Shows the Switching Hub's DRAM memory size.

(7) Fixed Baud Rate

Shows the baud rate of the Switching Hub's console port.

(8) Flash Size

Shows the Switching Hub's flash memory size.

(9) Administration Information

Shows the Switching Hub's administration information.

(10) Switch Name

Shows the Switching Hub's current host name.

(11) Switch Location

Shows the Switching Hub's current installation location name.

(12) Switch Contact

Shows the Switching Hub's current contact information.

(13) System Address Information

Shows the Switching Hub's address information.

(14) MAC Address

Shows the Switching Hub's MAC address.

(15) IP Address

Shows the Switching Hub's current IP address in operation.

(16) Subnet Mask

Shows the Switching Hub's current subnet mask in operation.

(17) Default Gateway

Shows the Switching Hub's current default gateway in operation.

(18) IPv6 Status

Shows the IPv6 Status (Enabled or Disabled).

Enabled

The IPv6 function is enabled.

Disabled

The IPv6 function is disabled.

(19) IPv6 Address/prefixlen

Shows the Switching Hub's current ipv6 address and prefix length in

operation.

(20) IPv6 Link Local Address

Shows the Switching Hub's current ipv6 link local address in operation.

(21) IPv6 Default Gateway

Shows the Switching Hub's current ipv6 default gateway in operation.

An example of executing the command to show the address information is shown below.

Fig. 2-2 Example of executing the command to show the address information

(1) MAC Address

Shows the Switching Hub's MAC address.

(2) IP Address

Shows the Switching Hub's current IP address in operation.

(3) Subnet Mask

Shows the Switching Hub's current subnet mask in operation.

(4) Default Gateway

Shows the Switching Hub's current default gateway in operation.

M24eG> enable M24eG# show ip conf

MAC Address : 00:C0:8F:A0:13:98 IP Address : 0.0.0.0 Subnet Mask : 0.0.0.0 Default Gateway : 0.0.0.0

M24eG#

(1)

(2)

(3)

(4)

An example of executing the command to show the ipv6 address information is shown below.

Fig. 2-3 Example of executing the command to show the ipv6 address

information

(1) IPv6 Status

Shows the IPv6 Status (Enabled or Disabled).

Enabled

The IPv6 function is enabled.

Disabled

The IPv6 function is disabled.

(2) MAC Address

Shows the Switching Hub's MAC address.

(3) IPv6 Address/prefixlen

Shows the Switching Hub's current IPv6 address in operation.

(4) IPv6 Link Local Address

Shows the Switching Hub's current ipv6 link local address in operation.

(5) IPv6 Default Gateway

Shows the Switching Hub's current IPv6 default gateway in operation.

M24eG> enable M24eG# show ipv6 conf

IPv6 Status : Disable MAC Address : 00:C0:8F:A0:13:98 IPv6 Address/prefixlen : ::/128 IPv6 Link Local Address : :: IPv6 Default Gateway : ::

M24eG#

(1)

(2)

(3)

(4)

(5)

show sys-info

Shows the Switching Hub's system information (such as up time and version information).

[Parameter]

Parameter name

Description

None

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

None

[Note]

Parameter name

Note

None

show ip conf

Shows the address information (such as MAC address and IP address) of the Switching Hub.

[Parameter]

Parameter name

Description

None

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

None

[Note]

Parameter name

Note

None

show ipv6 conf

Shows the ipv6 address information (such as MAC address and IPv6 address) of the Switching Hub.

[Parameter]

Parameter name

Description

None

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

None

[Note]

Parameter name

Note

None

3. Basic Switch Configuration

3.1. System Administration Configuration

Configure the host name, installation location and contact information in "Global configuration mode." Confirm the configuration information by executing the "show sys-info" command in "Privileged mode."

Command to show the system information

M24eG#

show sys-info

Command to set the host name

M24eG(config)#

hostname <hostname>

Command to delete the host name

M24eG(config)#

no hostname

Command to set the installation location

M24eG(config)#

snmp-server location <server location>

Command to delete the installation location

M24eG(config)#

no snmp-server location

Command to set the contact information

M24eG(config)#

snmp-server contact <server contact>

Command to delete the contact information

M24eG(config)#

no snmp-server contact

An example of executing the command to show the system information is shown below.

Fig. 3-1-1 Example of executing the command to show the system information

Terms related to this section are explained below.

(1) Administration Information

Shows the Switching Hub's administration information.

(2) Switch Name

Shows the Switching Hub's current host name.

(3) Switch Location

Shows the Switching Hub's current installation location name.

M24eG> enable M24eG# show sys-info

System up for : 0 days, 0:1:29 Boot Code Version : 1.00.17 Runtime Code Version : 1.0.0.07

Hardware Information Version : A1 DRAM Size : 128MB Fixed Baud Rate : 9600bps FLASH Size : 32MB

Administration Information Switch Name : Switch Location : Switch Contact :

System Address Information MAC Address : 00:C0:8F:A0:13:98 IP Address : 0.0.0.0 Subnet Mask : 0.0.0.0 Default Gateway : 0.0.0.0

System Address Information IPv6 Status : Disable MAC Address : 00:C0:8F:A0:13:98 IPv6 Address/prefixlen : ::/128 IPv6 Link Local Address : :: IPv6 Default Gateway : ::

M24eG#

(1)

(5)

(2)

(3)

(4)

(4) Switch Contact

Shows the Switching Hub's current contact information.

show sys-info

Shows the system information.

[Parameter]

Parameter name

Description

None

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

None

[Note]

Parameter name

Note

None

hostname <hostname>

Sets or edits the system name.

no hostname

Deletes the system name.

[Parameter]

Parameter name

Description

Set the system name.

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

Up to 50 one-byte characters

Allowed characters: alphanumeric character

(A-Z, a-z, 0-9) symbol (!@#$&_-.) white space

[Note]

Parameter name

Note

To set a system name containing white spaces,

enclose the entire name with a pair of

double-quotation marks (" ").

Example: hostname "switch a"

snmp-server location <server location>

Sets or edits the installation location information.

no snmp-server location

Deletes the installation location information.

[Parameter]

Parameter name

Description

Set the installation location.

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

Up to 50 one-byte characters

Allowed characters: alphanumeric character (A-Z,

a-z, 0-9) symbol (!@#$&_-.) white space

[Note]

Parameter name

Note

To set a location name containing white spaces,

enclose it with a pair of double-quotation marks

(" ").

Example: snmp-server location "Office 2F"

snmp-server contact <server contact>

Sets or edits the contact information.

no snmp-server contact

Deletes the contact information.

[Parameter]

Parameter name

Description

Set the contact information.

[Factory Default Setting]

Parameter name

Factory default setting

None

[Setting Range]

Parameter name

Setting range

Up to 50 one-byte characters

Allowed characters: alphanumeric character (A-Z,

a-z, 0-9) symbol (!@#$&_-.) white space

[Note]

Parameter name

Note

To set contact information containing white spaces, enclose it with a pair of double-quotation marks (" "). Example: snmp-server contact "network manager"

Overview: Set this Switching Hub's administration information (host

name, installation location, and contact information).

(1) Set this Switching Hub's name to "Switch." (2) Set this Switching Hub's installation location to "Office-2F." (3) Set this Switching Hub's contact information to "manager."

Fig. 3-1-2 Example of configuring the Switching Hub's administration

information

M24eG> enable M24eG# configure M24eG(config)# hostname Switch Switch(config)# snmp-server location Office-2F Switch(config)# snmp-server contact manager Switch(config)# exit Switch#

(1)

(2)

(3)

+ 408 hidden pages

Panasonic PN28480K-SG, PN28160K, PN28240K, PN28240K-ID, PN28480K Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual