Panasonic NV-GS280EB, NV-GS300EB User Manual

Operating Instructions

Digital Video Camera

Model No. NV-GS300

NV-GS300 NV-GS280

DV IN ± j

Before use, please read these instructions completely.

NV-GS280

VQT0T19

Dear Customer,

We would like to take this opportunity to thank you for purchasing this Panasonic Movie Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Please note that the actual controls and components, menu items, etc. of your Movie Camera may look somewhat different from those shown in the illustrations in these Operating Instructions.

Information for Your Safety

As this equipment gets hot during use, operate it in well ventilated place; do not install this equipment in a confined space such as a bookcase or similar unit.

To reduce the risk of fire, electric shock or product damage, do not expose this equipment to rain, moisture, dripping or splashing and ensure that no objects filled with liquids, such as vases, shall be placed on the equipment.

AC Adaptor

≥The rating plate is on the underside of the AC

Adaptor.

Caution for AC mains lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded threepin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5-amperes and it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE SOCKET.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

ª IMPORTANT

The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

Under no circumstances should either of these wires be connected to the earth terminal of the three-pin plug, marked with the letter E or the Earth Symbol Ó.

ª Before Use

Remove the Connector Cover.

ª How to replace the Fuse

The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.

1) Open the fuse cover with a screwdriver.

Figure A Figure B

Fuse cover

2) Replace the fuse and close or attach the fuse cover.

Figure A Figure B

Fuse (5 ampere)

VQT0T19

Operating instructions

≥These operating instructions cover the

NV-GS300 and NV-GS280.

≥The illustrations in these operating instructions

are for the model NV-GS300, but part of the description is for other models.

≥Some functions are not available depending on

the model.

≥SD Logo is a trademark. ≥Leica is a registered trademark of Leica

microsystems IR GmbH and Dicomar is a registered trademark of Leica Camera AG.

≥All other company and product names in the

operating instructions are trademarks of their respective corporations.

Files recorded on a SD Memory Card

It may not be possible to play back the files on this Movie Camera recorded on and created by other equipment or vice versa. For this reason, check the compatibility of the equipment in advance. ≥Keep the Memory Card out of reach of children

to prevent swallowing.

Pages for reference

Pages for reference are indicated by dashes either side of a number, for example:

The menu operation flow is indicated by >> in the description.

Use only the recommended accessories.

≥Do not use any other Multi cables and USB

cables except the supplied one.

≥When you use the cable which are sold

separately, please make sure to use the one whose length is less than 3 meters.

-00-

ª WARNING

To prevent electric shock, do not remove the cover (or back); there are no user serviceable parts inside. Refer servicing to qualified service personnel.

ª Carefully observe copyright laws.

Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.

≥The Movie Camera uses copyright-protected

technologies and is protected by the patented technologies and intellectual properties of Japan and the U.S. To use these copyrightprotected technologies, authorization of the Macrovision Company is required. It is prohibited to disassemble or modify the Movie Camera.

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper

treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

VQT0T19

Contents

Information for Your Safety .................................. 2

Before using

Accessories.......................................................... 5

Optional................................................................ 5

Parts identification and handling .......................... 6

Fitting the lens cap

(VW-LF37WE; optional) .................................... 8

The one-touch free-style grip belt ........................ 9

Power supply ....................................................... 9

Charging time and recordable time .................... 10

Turning the camera on....................................... 11

Setting date and time ......................................... 12

Using the LCD monitor....................................... 12

Using the viewfinder........................................... 13

Quick Start ......................................................... 13

Inserting/removing a cassette............................ 14

Inserting/removing a card .................................. 15

Selecting a mode ............................................... 16

How to use the joystick ...................................... 16

Help mode.......................................................... 18

Switching the language ...................................... 19

Using the menu screen ...................................... 19

Adjusting LCD monitor/viewfinder ...................... 20

Using the remote control.................................... 21

Record mode

Check before recording...................................... 24

Recording on a tape........................................... 25

Recording check ................................................ 26

Blank search function......................................... 26

Recording still pictures on a card while

recording image onto a tape............................ 26

Recording still pictures onto a card

(Photoshot)...................................................... 27

Zoom in/out function .......................................... 29

Recording yourself ............................................. 30

Backlight compensation function ....................... 30

Colour night view functions................................ 30

Soft skin mode ................................................... 31

Tele macro function ........................................... 31

Fade in/fade out function ................................... 31

Wind noise reduction function............................ 32

Anti-Ground-Shooting (AGS) ............................. 32

Using the built-in video flash .............................. 33

Self-timer recording............................................ 34

Wide/4:3 Function .............................................. 34

Image stabilizer function .................................... 35

Continuous Photoshot........................................ 35

Recording in various situations

(Scene mode).................................................. 36

Recording in natural colours

(White balance)............................................... 37

VQT0T19

Manual focus adjustment ................................... 38

Manual shutter speed/aperture adjustment........ 38

Playback mode

Playing back tape............................................... 40

Slow-motion playback/

frame-by-frame playback................................. 41

Variable-speed search function.......................... 41

Playback on TV.................................................. 42

Playing back card............................................... 42

Deleting files recorded on a card ....................... 43

Formatting a card............................................... 44

Protecting files on a card.................................... 44

Writing the printing data on a card

(DPOF setting) ................................................ 45

Edit mode

Recording from a tape onto a card..................... 46

Copying onto a DVD recorder or a VCR

(Dubbing)......................................................... 46

Using the DV Cable for Recording

(Digital Dubbing)............................................. 47

Audio dubbing .................................................... 48

Printing pictures by directly connecting

to the printer (PictBridge) ................................ 49

Menu list............................................................. 50

Menus related to taking pictures........................ 52

Menus related to playback ................................. 52

Other menus ...................................................... 53

Others

Indications.......................................................... 54

Warning/alarm indications.................................. 55

Functions cannot be used simultaneously ......... 56

Before requesting repair

(Problems and solutions)................................. 57

Cautions for Use ................................................ 60

Explanation of terms .......................................... 64

Specifications

Specifications..................................................... 65

Before using

ª Sales and Support Information

Customer Care Centre

≥For customers within the UK: 08705 357357 ≥For customers within the Republic of lreland:

01 289 8333

≥Visit our website for product information ≥E-mail: customer.care@panasonic.co.uk

Technical Support for AV Software ≥For UK, ROI: 08701 505610

Direct Sales at Panasonic UK

≥

Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday–Thursday

9.00 a.m.–5.30 p.m., Friday 9.30 a.m.–5.30 p.m. (Excluding public holidays)

≥Or go on line through our Internet Accessory

ordering application at www.panasonic.co.uk.

≥Most major credit and debit cards accepted. ≥All enquiries transactions and distribution

facilities are provided directly by Panasonic UK Ltd.

≥It couldn’t be simpler! ≥Also available through our Internet is direct

shopping for a wide range of finished products, take a browse on our website for further details.

Accessories

The followings are the accessories supplied with this product.

RJA0053-3X

K2KZ9CB00001

VFA0453

CGA-DU12

VSK0651B

VFC3506-1A

K2GJ2DZ00018

CR2025

N2QAEC000017

1) AC adaptor, DC input lead, AC mains lead

-9-

2) Battery pack -9-

≥The supplied battery pack is not available as

spare part, see the list of optional batteries below for alternative battery.

3) Remote control, button-type battery

-21-

4) Multi cable -46-

5) Shoulder strap -7-

6) USB cable and CD-ROM -49-

Optional

1) AC adaptor (VW-AD11EB)

2) Battery pack (lithium/CGR-DU06/640mAh)

3) Battery pack (lithium/CGA-DU07/680mAh)

4) Battery pack (lithium/CGA-DU12/1150mAh)

5) Battery pack (lithium/CGA-DU14/1360mAh)

6) Battery pack (lithium/CGA-DU21/2040mAh)

7) Wide conversion lens (VW-LW3707M3E)

8) Tele conversion lens (VW-LT3714ME)

9) Filter kit (VW-LF37WE)

10) Video DC light (VW-LDC10E)

11) Light bulb for video DC light (VZ-LL10E)

12) Stereo microphone (VW-VMS2E)

13) Tripod (VW-CT45E)

14) DV cable (VW-CD1E)

15) Jacket pouch (VW-SJ05E) ≥Some optional accessories may not be

available in some countries.

VQT0T19

Before using

Parts identification and handling

ª Camera

(5)

(1)

(2)

(3)

(4) (1) Built-in video flash -33- (2)

White balance sensor -37- Remote control sensor -22- Recording lamp -52-

(3)

Grip belt

(4)

(One-touch free-style grip belt) Lens (LEICA DICOMAR)

(5) (6) Lens cover (7) Microphone (built-in, stereo) -29-, -32-

(8)

(6)

(7)

-9-

A/V

MIC

(11)

(12)

(13)

(11) Viewfinder -13-, -63-

BATT

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the Viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

(12)

Battery holder

(13) Battery release lever [BATT] -10- (14)

Power switch [OFF/ON] -11- Status indicator -11-

(15)

Menu button [MENU] -19-

(16)

(9)

(10)

Joystick -16-

(17)

Mode dial -16-

(18)

Recording start/stop button -25-

(19)

(14)

(15)

(16)

(17) (18) (19)

Speaker -40-

(8)

Audio-video/S-Video output terminal

(9)

[A/V]

-46-

≥Use the supplied Multi cable only, otherwise

audio may not be played back normally.

(10) Microphone terminal [MIC]

≥A compatible plug-in powered microphone

can be used as an external microphone.

≥When the movie camera is connected with

AC adaptor, sometimes noise may be heard depending on microphone type. In that case, please switch to battery for power supply and noise will stop.

VQT0T19

Before using

(22)

(20) (21)

(27)

(28) (29)

(20) LCD monitor -12-, -63-

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.

(21) LCD monitor open part [OPEN] -12-

Mode select switch [AUTO/MANUAL/

(22)

FOCUS] Power LCD button [POWER LCD] -21-

(23)

USB terminal [ ] -49-

(24)

(NV-GS300)

(25)

DV input/output terminal [DV]

-24-, -36-, -38-

-47-

(NV-GS280) DV output terminal [DV] Reset button [RESET] -56-

(26)

Card access lamp -16-

(27)

Card slot -15-

(28)

Card slot cover -15-

(29)

(30)

(31)

-47-

(23)

(24) (25)

(26)

(32)

(33)

(34) (35)

(36)

Tripod receptacle

This is a hole for attaching the camera to optional tripod/VW-CT45E. (Please carefully read the operating instructions for how to attach the tripod to the camera.) ≥You cannot open the card slot cover when the

tripod is used. Insert the card first and then attach the tripod.

(37)

(37) Shoulder strap fixture

This is a fixture for attaching the shoulder strap to hang the camera from your neck or shoulder.

≥Put the strap through the fixture 1 and through

the stopper 2 so it will not come off. Extend part 3 by at least 2 cm.

≥Fit the other end of the belt similarly.

(30)

Cassette holder -14- Accessory shoe

(31)

≥Accessories, such as a stereo microphone

(VW-VMS2E; optional), are attached here.

(32) Cassette eject lever [OPEN/EJECT] -14-

Cassette cover -14-

(33)

Zoom lever [W/T] -29-

(34)

Volume lever [s /VOLr] -40 -

(35)

Photoshot button [PHOTO SHOT] -26-

VQT0T19

Before using

(38)

(38) Lens hood

In order to remove the lens hood, rotate it counterclockwise 1. In order to fit it, put into slot 2, and then rotate it clockwise. ≥Fit the MC protector or the ND filter of the Filter

Kit (VW-LF37WE; optional) in front of the lens hood. Do not fit the other accessories on the hood. (Except for the lens cap) (Refer to the operating instructions for the Filter Kit.)

≥When fitting the tele conversion lens

(VW-LT3714ME; optional) or the wide conversion lens (VW-LW3707M3E; optional), first remove the lens hood. (Refer to the operating instructions for the tele conversion lens or the wide conversion lens.)

≥When 2 lens accessories, such as the ND filter

and tele conversion lens, are fitted and the [W/ T] lever is pressed toward the [W] side, the 4 corners of an image will be darkened. (Vignetting)

≥The lens hood has a built-in lens cover.

Fitting the lens cap (VW-LF37WE; optional)

Fit the lens cap to protect the surface of the lens. The lens cap is included in the Filter Kit (VW-LF37WE; optional). If you do not use the movie camera when the MC protector or the ND filter of the Filter Kit (VW-LF37WE; optional) is attached to the front of the lens hood, attach the lens cap to protect the surface of the lens.

1 Push the string through the belt. Push the

lens cap through the loop in the string.

≥To fit or remove the lens cap (VW-LF37WE;

optional), hold both sides of the lens cap with the tips of your first 2 fingers.

VQT0T19

≥The lens cap removed can be hung on the lens

cap fixture. (It cannot be hung if the grip belt is used as a hand strap.)

Before using

The one-touch free-style grip belt

ª To use as a grip belt

Adjust the belt length so it fits your hand.

1 Adjust the belt length and the pad position.

1 Flip the belt. 2 Adjust the length. 3 Fix the belt.

To use as a hand strap

If you use the grip belt as a hand strap, then you can carry or handle this camera more easily.

1 Flip the belt.

1 Flip the belt. 2 Adjust the length.

2 Put your hand through the strap.

Power supply

ª Charging the battery

When this product is purchased, the battery is not charged. Charge the battery before using this product.

≥Battery charging time ( ≥We recommend using Panasonic batteries. ≥If you use other batteries, we cannot guarantee

the quality of this product.

≥If the DC input lead is connected to the AC

adaptor, then the battery will not get charged. Remove the DC input lead from the AC adaptor.

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Put the battery on the battery mount by

aligning the mark, and then securely plug it in.

Charging lamp

Lights up:Charging Goes off: Charging completed Flashing: The battery is over discharged

(discharged excessively). In a while, the lamp will light up and normal charging will start. When the battery temperature is excessively high or low, the [CHARGE] lamp flashes and the charging time will be longer than normal.

Connecting to the AC outlet

-10-)

≥Hold the movie camera in a way that the

microphones or sensors are not covered with your hands.

VQT0T19

Before using

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Connect the DC input lead to the AC

adaptor.

3 Connect the DC input lead to this product.

≥The output plug of the AC mains lead is not

completely connected to the AC adaptor socket. As shown in 1, there is a gap.

≥Do not use the power cord for other

equipment since the power cord is exclusively designed for the movie camera. Or do not use the power cord of other equipment for the movie camera.

Fitting the battery

Push the battery against the battery holder and slide it until it clicks.

Removing the battery

While sliding the [BATT] lever, slide the battery (or the DC input lead) to remove it.

BATT

≥Hold the battery with your hand so it does not

fall.

≥Before removing the battery, be sure to set the

[OFF/ON] switch to [OFF].

Charging time and recordable time

The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If the temperature is higher or lower than 25 oC, the charging time will become longer.

Supplied

battery/

CGA-DU12

(7.2 V/

1150 mAh) CGA-DU14

(7.2 V/

1360 mAh)

CGA-DU21

(7.2 V/

2040 mAh)

CGR-DU06

(7.2 V/

640 mAh)

CGA-DU07

(7.2 V/

680 mAh)

A Charging time B Maximum continuously recordable time C Intermittent recordable time

(The intermittent recordable time refers to recordable time when the recording and stopping operations are repeated.) “1 h 10 min” indicates 1 hour 10 minutes.

≥The battery CGA-DU12 is supplied. ≥The charging time and recordable time shown in

the table are approximations. The times indicate the recordable times when the viewfinder is used. The times in parentheses indicate the recordable times when the LCD monitor is used.

≥We recommend the Battery Pack CGA-DU12,

CGA-DU14 and CGA-DU21 for long time recording (2 hours or more for continuous recording, 1 hour or more for intermittent recording).

A 2 h 25 min B 2 h 15 min

(2 h 5 min)

C 1 h 10 min

(1 h 5 min)

A 2 h 45 min B 2 h 40 min

(2 h 30 min)

C 1 h 20 min

(1 h 15 min)

A 3 h 55 min B 4 h

(3 h 45 min)

C 2 h

(1 h 55 min)

A 1 h 40 min B 1 h 15 min

(1 h 10 min)

C 40 min

(35 min)

A 1 h 30 min B 1 h 20 min

(1 h 15 min)

C 40 min

(40 min)

VQT0T19

≥The recordable time will become shorter in the

following cases:

≥When you use both the viewfinder and the

LCD monitor simultaneously while rotating

Before using

the LCD monitor frontward to record yourself, using the 0 Lux colour night view function, etc.

≥When you use this camera with the LCD

monitor lit up by pressing the [POWER LCD] button.

≥The batteries heat up after use or charging. The

main unit of the movie camera being used will also heat up. This is normal.

≥Along with the reduction of the battery capacity,

the display will change: # #

# # . If the battery

discharges, then ( ) will flash.

Turning the camera on

ª How to turn on the power

While pressing the button 1, set the [OFF/ ON] switch to [ON].

OFF

≥The Status indicator lights red and the power

turns on.

≥In Tape Recording Mode or Card Recording

Mode, the lens cover opens.

≥In Tape Recording Mode or Card Recording

Mode, if the [OFF/ON] switch is set to [ON] while the LCD monitor is closed and the viewfinder is retracted, the power turns off and the lens cover closes.

How to turn off the power

While pressing the button 1, set the [OFF/ ON] switch to [OFF].

OFF

≥Set the [OFF/ON] switch to [OFF] when not

using the camera.

≥The Status indicator goes off when the power

turns off.

How to turn the power on and off with

the LCD monitor/viewfinder

When the power switch is set to [ON], the power can be turned on and off with the LCD monitor and the viewfinder when the unit is in Tape Recording Mode or Card Recording Mode.

OFF

1 Open the LCD monitor out or extend the

viewfinder to use. (

≥The LCD monitor or viewfinder will be

activated.

-12-, -13-)

2 Close the LCD monitor and retract the

viewfinder.

OFF

≥The power will not turn off unless the LCD

monitor is closed and the viewfinder is retracted.

≥The Status indicator automatically goes off

and the power turns off. (If quick start is set to

-13-), the unit goes into quick start

[ON] ( standby mode and the Status indicator lights green.)

≥The power does not turn off even if the

LCD monitor is closed and the viewfinder is retracted while recording on a tape.

3 Open the LCD monitor or extend the

viewfinder to turn the power on and use the movie camera again.

OFF

≥The Status indicator lights red and the power

turns on.

VQT0T19

Before using

Setting date and time

When the movie camera is turned on for the first time, [SET DATE AND TIME] will appear.

≥Select [YES] and press the centre of the

joystick. Do steps 2 and 3 below to set the date/ time.

If the screen shows the incorrect date/time, then adjust it.

≥Set to Tape Recording Mode or Card

Recording Mode.

1 Set [BASIC] >> [CLOCK SET] >> [YES].

-19-)

(

2 Move the joystick left or right in order to

select the item to be set. Then move the joystick up or down to set the desired value.

≥The year will change as follows:

2000, 2001, ..., 2089, 2000, ...

≥The 24-hour clock is used.

3 Press the joystick to determine the setting.

≥The clock function starts at [00] seconds.

About date/time

ª ≥The date and time function are driven by a built-

in lithium battery.

≥Make sure to check the time before recording

because the built-in clock is not very accurate.

Recharging the built-in lithium battery

ª ≥If [0] or [--] is appears when the camera is

turned on, then the built-in lithium battery has run down. Use the steps below to charge the battery. When turn on the power for the first time after charging, [SET DATE AND TIME] will appear. Select [YES] and set the date and time. Connect the AC adaptor to the camera or attach the battery to the camera, and the built-in lithium battery will be recharged. Leave the camera as is for approx. 24 hours, and the battery will drive the date and time for approx. 6 months. (Even if the [OFF/ON] switch is set to [OFF], the battery is still being recharged.)

WARNING

THE LITHIUM BATTERY IN THIS EQUIPMENT MUST ONLY BE REPLACED BY QUALIFIED PERSONNEL. WHEN NECESSARY, CONTACT YOUR LOCAL PANASONIC SUPPLIER.

Using the LCD monitor

You can record the image while viewing it on the opened LCD monitor.

1 Place your finger on OPEN and pull the LCD

monitor out in the direction of the arrow.

OPEN

≥It can open up to 90o.

2 Adjust the angle of the LCD monitor as you

prefer.

2 90o1 180o

≥It can rotate up to 180o 1 towards the lens or

90o 2 towards the viewfinder.

≥The brightness and colour level of the LCD

monitor can be adjusted from the menu.

≥If it is forcibly opened or rotated, the camera

may be damaged or fail.

≥If the LCD monitor is rotated by 180o towards

the lens and the viewfinder is extended (when recording yourself), the LCD monitor and the viewfinder simultaneously light.

VQT0T19

Before using

Using the viewfinder

ª Extending the viewfinder

Pull out the viewfinder and extend it by pinching the extension knob.

≥The viewfinder will be activated. (If the LCD

monitor is opened, the viewfinder will be deactivated.)

Adjusting the field of view

Adjust the focus by sliding the eyepiece corrector knob.

12:30:4512:30:45

12:30:45

1. 4. 2006

1. 4. 2006 1. 4. 2006

12:30:45

1. 4. 2006

≥You can adjust the brightness of the viewfinder

from the menu.

Quick Start

When quick start is ON the battery power is still being consumed, even when the LCD monitor and the viewfinder are closed. The movie camera will resume recording/pause mode about 1.7 seconds after the LCD monitor or the viewfinder is reopended. ≥Please note in quick start mode approximately

half the pause recording power is being consumed. Using quick start mode will reduce the battery recording/playback time.

≥This is only activated in the following cases.

≥A tape or a card is inserted, while the Tape

Recording Mode is set.

≥A card is inserted, while the Card Recording

Mode is set.

≥Set to Tape/Card Recording Mode.

1 Set [SETUP] >> [QUICK START] >> [ON].

-19-)

(

2 While the [OFF/ON] switch is still set to

[ON], close the LCD monitor and retract the viewfinder.

OFF

≥The Status indicator lights green and the unit

goes into quick start standby mode.

≥The lens cover does not close. ≥The movie camera will not go into quick start

standby unless the LCD monitor is closed and the viewfinder is retracted.

3 Open the LCD monitor or extend the

Viewfinder.

OFF

≥The Status indicator lights red and the

camera is put into recording pause approx.

1.7 seconds after it is turned on.

VQT0T19

Before using

ª To cancel Quick Start

Set [SETUP] >> [QUICK START] >> [OFF].

-19-)

(

≥If the [OFF/ON] switch is set to [OFF] while the

unit is in quick start standby, the lens cover closes and the power turns off.

≥If the standby continues for approx. 30 minutes,

then the Status indicator will go off and the camera will be completely turned off.

≥If the Mode dial is moved or the battery is

removed in quick start standby mode, quick start is cancelled and the power turns off.

≥When the camera is quick-started with the white

balance on automatic, it may take some time until the white balance is adjusted if the scene being recorded has a light source different from the scene last recorded. (When the colour night view function is used, however, the white balance of the scene last recorded is retained.)

≥If the power is turned on in quick start standby,

the zoom magnification becomes 1k and the picture size may differ from what it was before quick start standby.

≥If [POWER SAVE] (

-52-) is set to [5 MINUTES]

and the unit automatically goes into quick start standby mode, set the [OFF/ON] switch to [OFF], then to [ON] again. Also, close the LCD monitor and retract the viewfinder and then open the LCD monitor or extend the viewfinder again.

≥When using the AC adaptor, Quick Start can be

used even if a tape/card is not inserted.

Inserting/removing a cassette

1 Fit the AC adaptor or the battery and turn on

the power.

2 Slide the [OPEN/EJECT] lever and open the

cassette cover.

OPEN EJEC

≥When the cover is fully opened, the cassette

holder will come out.

3 After the cassette holder is opened, insert/

remove the cassette.

≥When inserting a cassette, orient it as shown

in the figure, and then securely insert it as far as it goes.

≥When removing, pull it straight out.

4 Push the [PUSH] mark 1 in order to close

the cassette holder.

VQT0T19

PUSH

≥The cassette holder is housed.

5 Only after the cassette holder is completely

housed, close the cassette cover tightly.

Before using

≥When inserting a previously recorded cassette,

use the blank search function to find the position where you want to continue recording. If you are overwriting a previously recorded cassette, be sure to find the position where you want to continue recording.

≥When closing the cassette cover, do not get

anything, such as a cable, caught in the cover.

≥After use, be sure to rewind the cassette

completely, remove it and put it in a case. Store the case in an upright position. (

-63-)

≥If the indicator of the condensation does not

display on the LCD monitor and/or viewfinder and you notice condensation on the lens or the main unit, do not open the cassette cover otherwise condensation may be formed on the heads or the cassette tape. (

When the cassette holder does not

-60-)

come out

≥Close the cassette cover completely, and then

open it again completely.

≥Check if the battery has run down.

When the cassette holder cannot be

housed

≥Set the [OFF/ON] switch to [OFF], then to [ON]

again.

≥Check if the battery has run down.

Accidental erasure prevention

If the accidental erasure prevention slider 1 of a cassette is opened (slide in the direction of the [SAVE] arrow), the cassette cannot be recorded. When recording, close the accidental erasure prevention slider of the cassette (slide in the direction of the [REC] arrow).

R E C

SAVE

Inserting/removing a card

Before inserting/removing a card, set the [OFF/ ON] switch to [OFF]. ≥If the card is inserted or removed with the power

turned on, this camera may malfunction or the data recorded on the card may be lost.

1 Turn off the power 1.

OFF

≥Check that the Status indicator has gone off.

2 Open the card slot cover.

3 Insert/remove the card into/from the card

slot.

≥When inserting a card, face the label side 1

towards you and push it straight in with one stroke as far as it goes.

≥When removing the card, press the centre of

the card and then pull it straight out.

4 Securely close the card slot cover.

Concerning the card

≥Do not format the card with another movie

camera or any personal computer. This operation may make the card unusable.

≥Do not touch the terminals on the back of the

card.

≥Electrical noise, static electricity, or failure of the

movie camera or the card may damage or erase the data stored on the card. We recommend saving important data on a personal computer by using a USB cable, PC card adaptor, and USB reader/writer.

VQT0T19

Before using

ª Card access lamp

≥When the camera accesses the card (reading,

recording, playback, erasing, etc.), the access lamp lights up.

≥If the following operations are performed when

the access lamp is lit, then the card or the recorded data may be damaged or the camera may malfunction.

≥Inserting or removing the card. ≥Operating the [OFF/ON] switch or the mode

dial.

≥Attaching and removing the battery.

SD Memory Card

ª ≥The memory capacity indicated on the SD

Memory Card label corresponds to the total amount of capacity to protect and manage the copyright and the capacity available as conventional memory for a movie camera, personal computer or other equipment.

Concerning the write protection

switch on the SD Memory Card

≥The SD Memory Card has a write protection

switch on it. If the switch is moved to [LOCK], you cannot write to the card, erase the data on it, or format it. If it is moved back, you can.

Selecting a mode

Rotate the mode dial to select the desired mode.

1 Rotate the mode dial.

≥Set your desired mode to 1.

: TAPE RECORDING MODE

Use this when you record the image on a tape. (Also, you can simultaneously record still pictures on a card while recording images on a tape.)

: TAPE PLAYBACK MODE

Use this to play back a tape.

: CARD RECORDING MODE

Use this to record still pictures on a card.

: CARD PLAYBACK MODE

Use this to play back the still pictures recorded on a card.

: PC CONNECTION MODE

You can view or edit the images recorded on a card on your personal computer. (Refer to the operating instructions for PC connection.)

How to use the joystick

ª Basic joystick operations

Operations on the menu screen and selection of files to be played back on the multi-image display

Move the joystick up, down, left, or right to select an item or file, and then push in the centre to set it.

VQT0T19

1 Select by moving up. 2 Select by moving down. 3 Select by moving left. 4 Select by moving right. 5 Determine by pushing the centre.

Before using

ª Joystick and screen display

Push the centre of the joystick, and icons will be displayed on the screen. Each time the joystick is moved down, the indication changes. (In the Tape playback mode or the Card Playback Mode, the icons will be automatically displayed on the screen.)

1) Tape recording mode

([AUTO/MANUAL/FOCUS] switch is set to [AUTO])

2 Fade 3 Backlight compensation -30-

1/4

-31-

1 Help mode -18-

-31-

-30-

-26-

2 Soft skin mode

2/4

1 Tele macro -31- 3 Colour night view/

3/4

4/4

0 Lux colour night view

2 Recording check 1 Blank search -26-

≥1 is displayed while recording on a tape.

2) Tape recording mode ([AUTO/MANUAL/FOCUS] switch is set to [MANUAL])

2 Iris or gain value 3 White balance -37-

5/5

1 Shutter speed -38- 2 Manual focus adjustment

6/6

(When set to [FOCUS])

≥1 is displayed while recording on a tape. ≥2 is displayed only when the [AUTO/

MANUAL/FOCUS] switch is set to [FOCUS].

3) Tape playback mode

-38-

3 Playback/pause 4 Stop -40- 2 Rewind (review playback) -40- 1 Fast forward (cue playback) -40-

-40-

VQT0T19

Before using

4) Card recording mode ([AUTO/MANUAL/FOCUS] switch is set to [AUTO])

2 Self-timer recording 3 Backlight compensation -30-

1/2

1 Help mode -18- 2 Soft skin mode

2/2

1 Tele macro -31-

5) Card recording mode ([AUTO/MANUAL/FOCUS] switch is set to [MANUAL])

2 Iris or gain value 3 White balance -37-

3/3

1 Shutter speed -38- 2 Manual focus adjustment

4/4

≥1 is displayed only when the [AUTO/

MANUAL/FOCUS] switch is set to [FOCUS].

6) Card Playback Mode

(When set to [FOCUS])

Help mode

Select an icon for an explanation of the function.

≥Set to Tape/Card Recording Mode.

1 Press the joystick to display the icon during

the recording pause. Move the joystick down until icon 1 appears.

-34-

-31-

2 Move the joystick right to select the Help

mode icon [ ].

≥The help mode explains the operation icons

displayed when the [AUTO/MANUAL/ FOCUS] switch is set to [AUTO] in Tape/Card Recording Mode.

3 Move the joystick up, left, or right to select

the desired icon.

-38-

≥An explanation of the selected icon is

displayed on the screen.

≥Each time the joystick is moved down, the

indication changes.

To exit the Help mode

Select [EXIT] icon or press the [MENU] button.

3 Slide show start/pause 4 Delete -43- 2 Playback previous picture -42- 1 Playback next picture -42-

VQT0T19

≥When the Help mode is used, functions cannot

-42-

be set.

Before using

Switching the language

You can switch the language on the screen display or the menu screen.

1 Set [LANGUAGE] >> select the desired

language.

Using the menu screen

For each individual menu, please refer to -50-.

1 Press the [MENU] button.

≥The menu corresponding to the mode

selected by the mode dial is displayed.

≥Do not switch the mode dial when the menu is

displayed.

2 Move the joystick up or down in order to

select the top menu.

5 Move the joystick right or press it to set the

selection.

6 Move the joystick up or down in order to

select the item to be set.

7 Press the joystick to determine the setting.

To exit the menu screen

Press the [MENU] button.

To get back to the previous screen

Move the joystick left.

3 Move the joystick right or press it to set the

selection.

4 Move the joystick up or down in order to

select the sub-menu.

About the menu setting

ª ≥The menu is not displayed while recording on a

tape or a card. Also, you cannot record on a tape or a card while the menu is displayed.

Operating with remote control

The menu screen transition is the same as when the buttons on the main unit are used.

1 Press the [MENU] button.

VQT0T19

Before using

2 Select a menu item.

≥Use the direction buttons (3, 2, 1, 4) and

[ENTER] button in place of the joystick on the main unit.

3 Press the [MENU] button to exit the menu

screen.

Adjusting LCD monitor/viewfinder

ª Adjusting the brightness and colour

level

Set [SETUP] >> [LCD SET] or [EVF SET] >>

[YES].

2 Move the joystick up or down in order to

select the item to be adjusted.

[LCD SET]

:Brightness of the LCD monitor

:Colour level of the LCD monitor

[EVF SET]

:Brightness of the viewfinder

EVF

3 Move the joystick left or right to move the

bar indication representing the brightness.

4 Press the [MENU] button or the joystick to

complete the settings.

≥When the LCD monitor is rotated by 180°

towards the lens, the brightness of the LCD monitor cannot be adjusted.

≥To adjust the brightness of the viewfinder, close

the LCD monitor and extend the viewfinder to activate it.

≥These settings will not affect the images actually

recorded.

VQT0T19

Before using

ª In order to increase the brightness of

the entire LCD monitor

Press the [POWER LCD] button.

POWER LCD

≥The [ ] indication appears on the LCD

monitor.

≥If the [POWER LCD] button is pressed, the

entire LCD monitor will become approx. twice as bright as the normal.

≥When the [POWER LCD] button is pressed

again, the [ ] indication disappears and the original brightness is restored.

≥This will not affect the images to be recorded. ≥If you turn on the camera when the AC adaptor

is used, the [POWER LCD] function will automatically be activated.

≥You cannot use this function in PC Connection

Mode.

Changing the picture quality on the

LCD monitor

Set [SETUP] >> [LCD AI] >> [DYNAMIC] or

[NORMAL].

[DYNAMIC]: The image on the LCD monitor

[NORMAL]: Switches to the standard picture

≥The effect will vary depending on the scene

recorded.

≥The picture quality on the viewfinder will not be

affected.

≥This function is automatically set to [DYNAMIC]

when the brightness of the LCD monitor is increased (the [ ] indication appears on the LCD monitor) and cannot be set to [NORMAL] independently.

≥This will not affect the images to be recorded. ≥When the LCD monitor is rotated by 180°

towards the lens, the picture quality of the LCD monitor is temporarily adjusted as if the [LCD AI] is set to [NORMAL].

becomes clear and vivid. Optimum contrast and brightness are set depending on the scenes recorded. Clear and brilliant images are presented.

quality.

Using the remote control

ª Remote control

Using the remote control supplied will enable controlling almost all the functions of this camera to be controlled.

(1) (2)

(1) On-screen display button [EXT DISPLAY]

-42-

Date/time button [DATE/TIME] -50-

(2) (3)

Audio dubbing button [AUDIO DUB] -48- Record button [¥REC] (not available

(4)

NV-GS280) Direction buttons [3, 2, 1, 4] -20-

(5)

(6)

Slow/frame-by-frame forward button

-47-

(6)

[E, D] (E: reverse, D: forward) Zoom/volume button [ZOOM/VOL] ¢

(7) (8) Search button [VAR SEARCH] -41-

Menu button [MENU] ¢ -19-

(9)

(3) (4)

(5)

(7)

(8) (9)

-41-

VQT0T19

+ 47 hidden pages