Panasonic NI-R71NR User Manual

1. Fill the iron as described in "HOW TO FILL"

2. Set the iron vertically and make sure the temperature selector dial is set to OFF. Plug the AC cord into the electrical outlet.

3. Set the temperature selector dial to the " indication area.

4. Preheat the iron until the indicator light goes out, usually about

1-2 minutes.

5. Simply pump the jet of steam button when it is desired. But pump the jet of steam button several times before useing for the first time at each ironing session.

6. Allow at least 5 seconds between uses of jet of steam to prevent water spotting. Use a press cloth if necessary.

VERTICAL STEAM

To get better results when using vertical Jet of steam,hang the garment on a clothes hanger. Curtain and drapes may also be steamed once they're hung. Hold the iron away from your body close to but not touching the fabric. Pull the fabric tight with your free hand and pump the Vertical steam button

(Jet of Steam Button) at 5-second intervals as you pass the

iron over the wrinkled fablic.

WARNING

Never iron clothes on the body or point your iron at anyone when steaming. Keep hands and body away from steam areas while using vertical steam

feature.

SELF-CLEANING

With the self-cleaning feature you can flush out mineral residue from the steam generating chamber and the steam vents.refreshing your iron each time for a longer steaming life. It is very important to operate the self-cleaning feature after each steam ironing to prevent mineral accumulations from hardening.

1. Check water level. Water level should be at 1/2 full mark. When water level is below 1/2 full, fill with water according to the instructions in "How to Fill".

2. Preheat at "6" setting, (in about 1-2 minutes) Makes sure that the steam button is in the Dry position.

3. Set the dial to OFF and remove the AC plug.

4. Hold the iron horizontally over the sink.

5. Pump the "Jet of Steam" button quickly (at leasts

times per second) about 20-30 times.

6. While self-cleaning, pitch the iron up and down slowly

to help clean the entire inside and let the water drip out of the soleplate vents.

7. Check that all water and steam thoroughly stop coming out of the sole plate vents. After self-cleaning is finished dump any remaining water out of the iron.

8. Iron on a towel to remove any drops of water remaining on the bottom of iron.

9. Cool as usual and store the iron on its heel rest. Never store an iron on its soleplate or with water in it.

NOTE:

If water still remains inside the sole plate after self-cleaning operation, then dry out the iron by vaporizing the remaining water setting the iron on the "6" setting, and follow the instructions under "AFTER EACH USE".

Stay Clean Vents ( ni-R71NR/R72NR Only ;

The built-in Anti Calcium Cassette in the Capsule Tank continuously reduces scale built-up in the vaporizing chamber of the iron. This system makes it possible to use steam function for a long period of time preventing steam vents clogging.

HOW TO CARE FOR YOUR IRON

AFTER EACH USE

1. Turn iron off and unplug.

2. Empty iron immediately after using. Don't store the iron with water in it.

3. Depress the steam button down into the dry position.

4. Wait until the iron has cooled before storing it, and always set it on the heel rest to protect the soleplate from scratches, corrosion or stains.

5. After letting iron cool completely, push the cord wind button to wind the cord. Store iron vertically in a safe place after winding cord completely.

MAIN BODY

After unplugging and cooling the iron, simply wipe off with a damp cloth and if necessary, use a mild detergent.

NEVER USE ANY HARSH CLEANERS.

SOLEPLATE

Starch and other residue may be easily removed from the soleplate with a damp cloth. To avoid scratching the finish never use a metallic pad to clean the soleplate, and never place the iron on a rough surface.

If synthetics are ironed at too high a temperature, not only is the fabric usually ruined, but the iron soleplate is often covered with the melted remains of the synthetic fabric. The best way to remove synthetic residue from the soleplate is to heat the iron and to iron over an old cotton rag.

CAUTION:

Never use steam iron cleaners in the iron, since they may damage the inside of the iron.

FABRIC IRONING CHART

NOTES: 1. Check garment for specific ironing instructions. Always follow manufacturer's

instructions.

2. Iron blended fabrics at setting for lower-temperature fiber or for the highest-percentage fiber.

3. Use caution, some synthetics may melt at high temperature.

Temperature Selector Setting

4 5

' Trademarks of Fiber Manufacturers.

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus New Jersey 07094

consumerproducts @ panasonic.com

Fabric

ACRYLIC

* ACRILAN * CRESLAN

* ORLON ACETATE METALLICS SUEDE

NYLON

* ANTORON

* CAPROLAN SILK

PERM. PRESS RAYONS

POLYESTER

* DACRON

* FORTREL

* KODEL TRIACETATE

* ARNEL

W'n W COTTON

WOOL VELVET

COTTON

LINEN

Ironing Recommendations

Dry iron on wrong side, or use a press cloth on top of fabric. Don't sprinkle water directly on fabric to avoid spots. To iron suede, cover ironing board with brown paper and use it as a press cloth.

Dry iron on wrong side.

Dry iron on wrong side. To touch-up coiiars, cuffs, pockets, etc., iron lightiy on right side.

Steam ironing is suggested. Never iron completeiy dry. To iron velvet, steam iron holding the slightly above the fabric

Steam ironing is suggested. Sprinkle water on the fabric, depending on its thickness, iron dark fabric on wrong side to avoid unwanted sheen.

Steam ironing is suggested, iron dark fabrics on wrong side to avoid unwanted sheen.

Panasonic Sales Company Division of Matsushita Electric of Puerto Rico, Inc.C'PSC") Ave.65 de Infanterie. Km. 9.5 San Gabriel Industrial Pack, Carolina, Puerto Rico 00985

Ì8200Ò-ÓM47A

Panasonic

Electric Steam Iron

Operating Instructions

Model NO.NI-R50NR/R51 NR/R53NR/R54NR/R71NR/R72NR

NI-R50NR

Please read these instructions carefully before using this product and save this manual for future use.

For assistance, please call: 1-800-211-PANA(7262) or send e-mail to:cosumerproducts@panasonic.com or visit us at WWW.panasonic.com (U.S.A)

For assistance, please call : 787-757-4300 or visit us at WWW.panasonic,com (Puerto Rico)

IMPORTANT SAFEGUARDS

When using your flatiron,basic safety precautions should always be followed, including the following:

1. Read all instructions.

2. Use iron only for its intended use.

3. To protect against a risk of electric shock, do not immerse the iron in water or other liquids.

4. The iron should always be turned to OFF before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.

5. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Wind cord into cord reel unit when storing.

6. Always disconnect iron from electrical outlet when filling with water or emptying it and when not in use.

7. Do not operate iron with a damaged cord or if the iron has been dropped

or damaged. To avoid a risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.

8. Close supervision is necessary for any appliance being used by or near

children. Do not leave iron unattended while connected or on an ironing board.

9. Burns can occur from touching hot metal parts, hot water,or steam. Use

caution when you turn a steam iron upside down - there may be hot water in the reservoir.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.

2. If an extension cord is absolutely necessary, a 10 ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

-8-

COMPONENTS IDENTIFICATION

NI-R50NR/R51NR/R53NR/R54N/R71NR/R72NR

-9-

CAUTION DURING USE OF RETRACTIVE POWER CORD

(1) When retracting power cord, always grasp the plug with one hand while pressing the cord

wind button with the other hand.

(2) If cord does not retract completely, pull it out slightly and wind it again while guiding it into

the reel.

(3) Unwind the power cord in the amount of length you need before plugging it to the wall

outlet.

(4) If the power cord seems hard to unwind due to improper winding, pull firmly until it is

released.

(5) Do not allow small children to handle the retractive power cord as this may cause the

cord to "whip" and cause injury.

GENERAL HINTS BEFORE USING YOUR PANASONIC IRON

1. Read this instruction book to become familiar with the iron and its features.

2. Most ordinary tap water can be used in this iron. In extremely hard water areas, distilled or demineralized water should be used. Do not use water processed through home water softening systems, as this water contains minerals that may be harmful to the iron.

3. It is best to start ironing garments requiring lower temperature setting first. This will help to avoid damaging garments. If you are not sure of the fabric content, first test the temperature of the iron on an area of a garment where it will not show.

HELPFUL IRONING TIPS

The Temperature Selector Dial of the Panasonic iron has dots on it, in addition to numbers and color indications. This makes it easy to adjust the iron for steam, more or less steam, and any other temperature setting desired. The dots are international fabric protection symbols for various temperature ranges:

• Low Temperature

• • Medium Temperature

• •• High Temperature

Many garments are labeled with these dots as a guide for selecting the proper ironing temperature. For general information about ironing temperatures, refer to the handy fabric guide on the iron. For more specific information, use the "Fabric Ironing Chart" found on page 10. As a guide to the international Textile Care Labeling code,the following symbols are noted for your information.

INTERNATIONAL TEXTILE CARE

& LABELING CODES

\=l A

Washing Bleaching Ironing Dry Cleaning

A symbol crossed out indicates that the article of clothing must not be subjected to the particular treatment.

EXAMPLE:(DO NOT BLEACH) ^

-10-

Before ironing, sort the garments according to the different heat settings required. Iron

fabrics that need a lower temperature first.

Do not touch plastic buttons with a hot iron because they may melt. Be careful around zippers and similar items to prevent the soleplate from scratching.

HOW TO FILL

1. Be sure the iron is unplugged from the electrical outlet before filling with water. Push the steam button down, hold the iron, open Water Fill Cover and slowly fill the iron with water (see NOTE) up to "MAX" indication.(about 5.6 ounces/160ml).

2. Do not overfill. Check the correct water level with the iron in the vertical position.

3. Close the Water Fill Cover.

NOTE:

Most ordinary tap water can be used in this iron. In extremely hard water areas, distilled or

demineralized water should be used. If distilled water is used, the iron must be seasoned by

using tap water for the first four times. After that, tap water should be used once a month. This is necessary to coat the steam chamber for proper performance.

HOW TO USE AS A STEAM IRON

1. Fill the iron as described in "HOW TO FILL".

2. Set the iron vertically and make sure the Temperature Selector Dial is set to OFF.

Plug the AC cord into the electrical outlet.

3. Set the temperature selector dial to the" t;;^"or " "(steam) zone.

"c!!!?" zone: Low steam, for thin or delicate fabrics requiring a small amount of steam.

zone: High steam, for fabrics requiring a lot of steam.(i. e. thick materials, items with

stubborn wrinkles.)

4. Preheat the iron until the indicator light goes out, usually about 1 -2 minutes.

This light will go on and off during ironing to indicate the temperature chosen by the selector

dial is being maintained.

5. Hold the iron horizontally and press the steam button into the steam position.

Steam button is regulated as follows.

NOTE: 3 position steam button.

('tea. V Dry

(Button UP : for High steam, MED: for Low steam ;

Temperature Zone

Low steam High steam

steam Button Position

jsl.M

Now steam ironing can begin

6. Anytime the iron is set vertically the steaming action will stop.

NOTE: Do not use the steam button unless the iron is sufficiently hot enough to produce

steam, otherwise water will leak out through the vents instead.

HOW TO USE AS A DRY IRON

1. Press the steam button down to the dry position.

2. Place the iron vertically, set the selector dial to OFF.

3. Plug in the iron.

4. Set the temperature selector dial to the desired position. (Refer to the Fabric Ironing Chart in this manual on page 10)

5. Preheat the iron until the indicator light goes out, usually about 1-2 minutes.

HOW TO USE THE SPRAY FEATURE

Before using the spray feature, check the garment label for ironing instructions because some fabrics may spot or stain with moisture. The spray feature is particularly helpful for removing stubborn wrinkles and where extra dampening is needed. The spray may be used with steam or dry ironing.

1. Simply pump the spray button when spray is desired. If the spray doesn't work immediately just keep pumping

till it does.

2. To get a finer spray, pump the button vigorously. To get coarser spray, pump the button more slowly. For best results, use a quick, full stroke.

-2-

Electronic 3-Way AUTO SHUT-OFF FUNCTION

1. When the iron is left unmoved with its soleplate facing down or on its side for approx. 1 minute, the iron will automatically shut off power to the heater by itself.

2. When the iron is left unmoved on its heel rest for approx. 10 minutes, the iron will automatically shut off power to the heater by itself.

3. To turn the iron back on to resume ironing, simply move the iron in any way.

Reheat the iron until the indicator light goes out, if you have left the iron in the auto shut

off mode for 10 minutes or more.

NOTE: 1. The Auto shut off system works regardless of position of the temperature selector

dial, even at "OFF" position.

2. When you finish ironing, always unplug the iron.

yii Licensed under U.S.patent No. 4,686,352 and foreign counterparts.

HOW TO USE THE JET OF STEAM FEATURE

The jet of steam feature gives extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. The jet of steam feature can be used only in the " " indication area of the temperature selector dial when steam or dry ironing (If used at lower setting, water spotting will occur because the iron is not hot enough to change water to steam). If you have not used the "Jet of Steam" feature for a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed. Simply test the "Jet of Steam" feature several times away from the ironing board and clothes to be ironed. This will prevent brown spotting or water spotting on the clothes.

-3-

-4-

-5- -7-