Page 1
Purified Water Electric Thermo Pot
NC-JD40N
NC-JD40C
3.0
2.0
1.0
Before using this unit, please read these instructions completely.
This product is intended for household use only.
Page 2
Nice taste
Provides the natural taste of the tea.
Boiling with "Bincho" charcoal
Inner container with charcoal far infrared fluorine
¥ The surface of the inner container is coated with
fluorine mixed with powdered 'Bincho' charcoal,
famous for its far infrared effect. This produces water
bringing out the color, taste, and fragrance of the tea.
Purification by active charcoal
Purification
¥ During heating, the water is circulated through the
charcoal filter and, the water is purified by active
charcoal.
¥ When the button "Reboil" is pressed during
water heating, the purification effect is increased by
forced boiling. ( P. 16)
Reboil Reboil
2
Active charcoal
Page 3
From the first drop
Dispensing of fresh hot water
¥ When the unlock button is pressed, the hot water in
once into the inner
container, so that hot water is dispensed from the very first drop.
Realization of energy savings
Maintaining
Use to make Milk for baby.
of 60°C
¥ Please cool down the temperature of the baby milk or mix with cool
boiled water before you give it to baby.
Maintaining
Better power savings than with maintaining of 98°C.
of 85°C
¥ A temperature of about 85¡C also is convenient for green tea.
Energy Saving
Power savings by timer setting before going to sleep or going out.
Timer
the pipe is circulated and returned
Example: Setting to "8 hours" at 10 o'clock in the evening will start
heating 8 hours later at 6 o'clock and then the water will be kept hot.
3
Page 4
Contents
Please read this first
Please observe these items.
Safety precautions
Part names and handling instructions
............................................5
How to use
After heating
Water heating
First, fill in water
Dispense hot water
Points to know
Convenient use methods
................................................14
.........................................18
................................20
..............12
5
12
15
19
21
For long use
To maintain good taste
Maintenance
Q&A
Troubleshooting
Replacement of parts
Specifications
..................................................24
.............................................................28
.............................................30
.....................................32
................................................33
25
28
30
32
33
5
12
25
28
30
32
15
33
19
21
4
Page 5
Safety precautions
In order to prevent harm or injury to those using the appliance or to any other persons and/or property, please be
sure to read the following safety instructions.
Possible consequences of incorrect usage are laid out in the following pages, each marked with a sign
according the degree of danger.
Be sure to obey them.
WARNING
Attention
This sign warns of possible death or serious injury to persons and/or property
This sign warns of possible damage or injury to persons and/or property
5
Page 6
Full pot mark
Lid
Dispensing
spout
Safety precautions
Be sure to obey them.
WARNING
Handling
Do not immerse the unit in water or pour water over it.
Container
Steam
vent
3.0
2.0
1.0
Flow control
pad
It may cause a short circuit and you may receive an electrical
shock.
Never disassemble, repair or modify the unit.
It may start a fire. The unit may operate abnormally and you may
be seriously injured.
●
For repairs (other than replacing consumable parts), please
contact our Service Center.
Do not put ice into the container and try to use it keep water
cool.
Condensation may occur, and later you may receive an electrical
shock or the unit may malfunction.
Main unit
Power Cord
MAX.WATERLEVEL
最高水位
To Prevent Burns
Do not allow children to use the unit and do not leave the
unit within the reach of infants.
They may be seriously burned, or receive an electrical shock
and they can die from their injuries.
Do not fill with water beyond the full pot mark.
Hot water can spill causing burns.
Do not boil anything other than water.
If tea bags, tea leaves, milk or alcohol are put in the container,
they may cause it to spurt hot liquid or steam and you may be
seriously burned.Those items may also cause the water tube to
become clogged. The container may burn or corrode, and the
fluororesin insulating coating may peel off.
Do not tilt or knock over the main unit.
Even when the flow control pad is locked, if the main unit is
knocked over, hot water may flow from the dispensing spout or
the steam vent. You may be seriously burned.
Do not lift, tilt or shake the unit. Do not move the unit by the
lid.
Even when the flow control pad is locked, if the main unit is tilted,
hot water may flow from the dispensing spout or the steam vent.
You may be seriously burned.
Close the lid securely.
If the unit tips over with the lid unsecured, hot water will gush out
and you may be seriously burned.
6
Page 7
7
Page 8
Power cord
Power plug*
Cord
Unit plug
*The shape of plug differs
according to reigion.
Safety precautions
Be sure to obey them.
WARNING
To Prevent Burns
Do not force the lid to close.
Hot water can spill causing burns.
Do not touch the steam vent with your hand.
You may be burned. Pay special attention so that infants cannot
reach the steam vent.
Do not ever block the steam vent.
Hot water may spurt out and you may be seriously burned.
Do not try to empty leftover hot water while the lid is attached.
If the lid comes off, hot water may splash on you and you may be
seriously burned.
Power Cord
Do not allow small metal parts near the unit plug.
You may receive an electrical shock, or they may cause a short
circuit or catch fire.
Do not allow infants access to the power cord.
You must pay special attention to prevent infants from putting
the plug for the unit into their mouths.
This may result in electric shock or injury.
Be very careful not to damage the power cord, wall plug or
the plug for the unit.
Do not damage or modify these items. Keep them away from
heating devices. Do not force the cord to bend tightly, twist it or
pull on it. Do not place a heavy object on the cord. Do not
bundle it together with another cord.
If a damaged cord or damaged plugs are used, you may receive
an electrical shock or they may cause a short circuit or a fire.
●
To have cord or plugs repaired, please contact our distributor.
Do not connect or disconnect the power plug or the unit plug
with wet hands.
You may receive an electrical shock.
Remove any dirt from the power plug or the unit plug right
away.
If dirt accumulates on the plugs, moisture may cause a loss of
insulation and it may cause a fire.
●
Disconnect the plugs and wipe them with a dry cloth.
Push the power plug all the way into the wall outlet.
If the plug is inserted improperly, you may receive an electrical
shock. The plug can get hot and it may cause a fire.
●
Do not use a damaged plug or a connection in a loose outlet.
Use a single outlet that matches the power rating of the unit.
If this unit and another appliance are plugged into an outlet at the
same time, the outlet may get hot and it can cause a fire.
8
Page 9
9
Page 10
Safety precautions
Be sure to obey them.
Main unit
Full pot mark
Lid opening
lever
Charcoal filter
Power cord
Power plug*
Cord
*The shape of plug differs according to reigion.
3.0
2.0
1.0
Unit plug
Lid
Attention
To Prevent Burns
Do not open the lid or dispense hot water while it is boiling.
You may be burned by splashing hot water or steam.
When opening the lid, keep your hand away from the steam.
You may be burned.
Do not rotate the main unit while dispensing hot water.
You may be burned by splashing hot water.
Do not use the unit on an unstable surface or on a plush carpet.
The unit may tip over and you may be seriously burned.
Do not touch the hot part of the main unit during or shortly after use.
Otherwise, you may be seriously burned.
When carrying the main unit, do not touch the lid opening lever.
If you do, the lid may open, and you may be seriously burned.
Wait until the unit gets cold before performing any maintenance.
Otherwise, you may be seriously burned.
●
When discarding hot water, be careful not to get burned.
Power Cord
When the unit is not being used, unplug the power cord from the outlet.
If the insulation deteriorates, you may receive an electrical shock or it may cause an electrical short or a fire.
To disconnect the power cord, be sure to pull the plug out of the outlet while holding the plug. Never pull
on the cord.
You may receive an electrical shock or the cord may start a fire due to a short circuit.
Only use the power cord designed specifically for the unit. Do not use a different cord and do not use
this cord with any other device.
It may cause a malfunction or it may start a fire.
Where to use the unit
Do not use the unit near a wall or close to furniture.
The wall or the furniture may be damaged due to steam or heat. They may become discolored or deformed.
Precautions When Cleaning the Unit with Citric Acid
●
Only use citric acid to clean our thermo pots.
●
Do not fill the pot beyond the full pot mark.
●
Produce hot water from tap water (do not add hot water to the pot).
Hot water may spurt out and you may be seriously burned.
How to clean with citric acid P.26, 27
10
Page 11
11
Page 12
Part names and handling instructions
Main unit
Lid
Dispensing spout
Rotating base (360 degrees)
When rotating the pot, do not allow the
cord to wind around the unit.
Checking the Enclosed Parts
Power cord Charcoal filter
Cord
Power plug*
Unit plug
(
Consumption part P. 32
Steam vent
Handle
Water level gauge
Filter (consumable part)
)
It is located at the bottom of the container.
If it comes off, replace it in the correct
position. ( P.32)
* The shape of plug differs according to reigion.
Caution:
Do not place the unit onto a vinyl table cloth or
similar.
(The odor of the vinyl or similar may be carried over into the water.)
Do not place near flames.
(It may cause deformation of the unit.)
12
Note:
Initially, there may be the smell of resin etc., but this
disappears with use.
Page 13
How to Remove the Lid
Depression
3. Wipe the body and the inner container
with a slightly moist dishcloth .
Installing and closing the lid
¥Install the lid diagonally from above.
¥Close the lid until it latches with a click.
Lid opening lever
Detachable
knob
Install the charcoal filter
1.Rinse the filter in water and then shake off the water.
Caution:
¥ Do not use a brush, detergents, or bleach. This can cause damage or smells,
and the purification effect may be lost.
1.
Press the depression in the lid
2. Push on the detachable knob, hold the lid opening lever,
and pull the lid out and up in a slanting direction.
Caution:
¥Do not use detergent. (This can cause a smell to remain.)
¥Do not use benzine or thinner. (This can damage the surface.)
opening lever, and lift the lid.
Attachment
position
2. Insert the filter to the attachment
position on the inside.
3. Push in all the way from the top.
13
Page 14
Water heating
At the time of first use
Heat water once and wash the inner container and the water passages.
Install the charcoal filter on the inner container. P. 13
Fill in water to the top level, insert the plug into an outlet, and heat water. P. 14 Ð 16
15 – 17
When the water has been heated, dispense about one half through the spout. P. 18
19
Disconnect the plug, remove the lid, and discharge the water from the discharge position. P. 18
19 19
1. Open the lid and fill in water.
Use a different container to fill the pot with water.
Caution:
¥ Do not fill in water directly from a faucet.(The water may
overflow, get into the electric parts, and cause trouble.
¥ Fill in water to a position from the "Refill" mark to the "Top
level" mark.(When there is too little water, the function for
prevention of empty heating will operate, and when there is too
much water, hot water may spill from the spout.)
Refill mark
Top level mark
Note:
¥ When water is heated in a kettle and filled into the jar pot, the
function for prevention of empty heating may operate.
15 – 17
19
)
14
Dechlorination
Long Boil Cleaning
Lit
Temp.
60 85 98
2. Heat the water.
1
2
Connect the plug.
Heating will start automatically.
¥
The temperature indication.
Increases in steps of 5¡C.
h
Page 15
Operation Panel
If the protective film is still covering the surface of the operation panel, peel it off before using the operation panel.
MADE IN JAPAN
Reboil
Timer
Select
Dechlorination
Long Boil Cleaning
Temp.
60 85 98
Keep Warm
h
Flow
Control
Lock
Unlock
Temp.
60 85 98
h
NC-JD40N NC-JD40C
* For explanation of the LED indication, the above figure shows all indications lit .
15
Page 16
Water heating
Dechlorination
Long Boil Cleaning
Temp.
h
Use long boiling to increase the
purification effect.
Reboil
Press during heating to display .
The boiling time is extended by about 3 minutes
and the purification effect is increased.
¥ Press again to return to normal boiling.
Reboil
Long Boil
Goes out.
Lit
Flashing alternately
Reboil
Buzzer sound
Dechlorination
Long Boil Cleaning
Temp.
h
60 85 98
Dechlorination
Long Boil Cleaning
Temp.
h
60 85 98
Buzzer sound
Dechlorination
Long Boil Cleaning
3.
The temperature will be maintained automatically.
When the water has been boiled, this will be announced
by a buzzer and will be shown on the display.
¥ Time until boiling
About 31 minutes
(Up to the top level mark with a room temperature of 20¡C.)
After a little while, the temperature will be maintained at .
To Prevent an Empty Container from
Being Heated
If an empty container is heated, the overheat safety
function (which prevents an empty container from
being heated) will be activated. The power will be
shut off automatically to prevent the problems that
can occur due to overheating. This will be shown on
the display.
¥ How to cancel the display Pour water into the container,
and press the key .
When the container is heated with no water in it or with the
water level below the low water level line, a bad smell may
be caused or the fluororesin coating may become discolored.
Please observe the following.
¥
Do not connect the power without pouring water into the
container.
¥
Do not boil water when the level is too low.
¥
After water is added, do not leave the lid open.
Reboil
16
Lit
Temp.
h
60 85 98
Keep Warm
Page 17
Reboil
Long Boil Long Boil
Reboil
Reboil
Reboil
31 31
Reboil
Reboil
17
Page 18
Dispense hot water
"Refill" position
Beep
Place the vessel at the dispensing position and dispense hot water.
Press to unlock the flow control pad.
Press to dispense hot water.
2.0
1.0
Locking will be done automatically about 10 seconds after
the end of dispensing.
Refill before the "Refill" position is reached.
Disconnect the plug and remove the lid.
Discharge from the discharge position.
Lock
Unlock
Unlock lamp lit
Flow
Control
The dispensing quantity can be adjusted by the force
with which the button is pressed.
¥ Strong: Strong flow
¥ Weak: Weak flow
The unlock lamp goes out and no hot water will be dispensed
even when the button is pressed.
Flow
Control
¥ To lock the button immediately after dispensing water.
Press the . The unlock lamp will go out.
Lock
Unlock
Note:
¥ For some time after boiling, bubbles from the boiling may
get into the pump and dispensing may be impaired.
This can be corrected by opening and closing the lid.
* Watch out for the steam when opening the lid.
Refill when the water level has dropped.
Caution:
¥ Do not leave the jar pot standing with an open lid.
(This may cause the function for prevention of empty
heating to operate.)
Empty the jar pot when it is not being used.
Caution:
¥ Do not discharge hot water from the operation side.
(This can cause trouble.)
¥ Do not leave water in the inner container. (This can cause
rust and/or smell.)
18
Note:
¥ When there is still a remaining charge after the plug has
been pulled, the temperature indication will appear.
Page 19
Lock
Unlock
Lock
Unlock
Flow
Control
Lock
Unlock
Flow
Control
Flow
Control
Lock
Unlock
Flow
Control
19
Page 20
Convenient use methods
To save electricity
¥
Electricity can be saved by lowering the holding temperature from about 98¡C to about 85¡C or about 60¡C .
¥ Use the timer when the jar pot is not to be used for some time, for example at night.
Setting is possible in steps of 4, 6, 8, and 10 hours.
¥ Further savings are possible by combining the timer and a holding temperature of 85¡C or 60¡C.
85¡C 60¡C
Dechlorination
Long Boil Cleaning
Temp.
Long Boil Cleaning
h
Temp.
60 85 98
Keep Warm
Dechlorination
Long Boil Cleaning
Temp.
Long Boil Cleaning
Temp.
60 85 98
Keep Warm
Dechlorination
Long Boil Cleaning
Dechlorination
h
60 85 98
Keep Warm
Dechlorination
60 85 98
Keep Warm
Holding temperature 85¡C
Select
Press and set to .
In about 1.5 hours, the water
temperature will drop to
about 85¡C
(in case of filling up to the top
level and a room temperature
of 20¡C).
¥ The temperature indication
drops as shown below:
Tip:
¥ A water temperature of
about 85¡C is also
appropriate for green tea.
¥ Holding at 85¡C also can
be set during heating.
Holding temperature 60¡C
Select
Press and set to .
In about 6 hours, the water
temperature will drop to
about 60¡C
(in case of filling up to the top
level and a room temperature
of 20¡C).
¥ The temperature indication
drops as shown below:
Tip:
¥ A water temperature of
about 60¡C is also
appropriate for baby milk.
¥ Holding at 60¡C also can
be set during heating.
Setting the timer
Example: Setting for 8 hours at 10 o'clock in the evening
20
Temp.
h
60 85 98
Dechlorination
Long Boil Cleaning
Temp.
h
60 85 98
Timer
Press and display .
10 o'clock in the evening: Timer start
¥ The remaining time is indicated in units of 1 hour.
¥ The temperature will drop, but a minimum temperature
of about 60¡C will be maintained.
6 o'clock next morning: Timer end
The water temperature will start to rise and holding will be
done at the set temperature.
Tip:
¥ The timer also can be set during heating.
In this case, the water first will be heated until it boils.
Page 21
Select Select
Timer Timer
Select Select
21
Page 22
Convenient use methods
When hot water is desired during holding or during timer operation
¥ For coffee, tea, instant food, etc.
Reboil
Timer
Select
Long Boil Cleaning
Temp.
Dechlorination
Lit
Long Boil Cleaning
Temp.
60 85 98
Buzzer sound
MADE IN JAPAN
Dechlorination
60 85 98
Keep Warm
h
The mark moves each time the button is pressed, so that
the setting for the holding temperature can be changed.
Cleaning
h
The setting time for the timer changes each time the button is
pressed.
(Return to temperature indication)
During holding and use of the timer
¥ When the water temperature has dropped because of refilling
etc., the water will be heated once until it boils.
¥ The water in the inner container is circulated once about every
6 hours. This is done to prevent accumulation of bubbles in the
pump, which can impair dispensing.
Cancel
Reheating
Reboil
Press .
Boiling will be notified after several minutes.
¥ Time until boiling
Holding at 98¡C: About 3 or 4 minutes
Holding at 85¡C: About 8 to 10 minutes
During timer operation: Within 18 minutes
(Filled up to the top level and at a room temperature of 20¡C).
22
Lit
Goes out
Dechlorination
Long Boil Cleaning
Temp.
h
60 85 98
Tip:
¥ The holding temperature and the timer setting remain as
they are.
Page 23
Cleaning Cleaning
Cancel Cancel
Reboil Reboil
34
810
18
34
810
18
23
Page 24
Maintenance (always first discharge the water and wait for the unit to cool down)
Daily maintenance
Main unit and lid
Wipe any water off the main unit and the lid using a dry dish cloth.
Caution:
¥
Do not submerge the main unit or the lid in water.
(If water enters the main unit from the bottom or from the
dispensing spout, it can also get into the electrical
components in the main unit and it may cause a malfunction.)
¥
Do not use detergents.
(They may leave an odor.)
¥
Do not use benzine or thinner to clean the pot.
(They may damage the surface.)
Container
Wipe any water off the inside of the container using a damp sponge.
Caution:
¥
Do not use polishing powder, a scrub brush or a nylon
brush to clean the container.
(They may damage the fluororesin finish.)
In regard to incrustations
With use of the jar pot, the calcium and other minerals in the
water will be deposited on the inner container and the filter.
This is called incrustation, but it is not harmful.
24
Charcoal filter
Remove and rinse in water (once every two or three months)
Caution:
¥
Do not use a brush, detergent, or bleach.
(This can cause damage or attachment of a smell, and the
purification effect may be lost.)
Filter
Clean the filter using a brush.
*After washing the filter, be sure to reattach it to the container.
Caution:
¥
Do not wash in a dishwasher and never put it in a heated dish
dryer. (The unit may become deformed.)
At the time of storage
¥
Dry the body and thel purification filter sufficiently.
¥
Keep the jar pot it a tightly closed plastic bag or similar to
prevent insects from getting into it.
Page 25
25
Page 26
Maintenance (always first discharge the water and wait for the unit to cool down)
eboil
Timer
Lit
Dechlorination
Long Boil Cleaning
Temp.
h
60 85 98
Wash with citric acid (about once every 2 or 3 months).
When incrustations have formed
1. Always first remove the charcoal filter.
Make sure that the filter is attached to the container.
2.
3. Put citric acid in the container.
4.
Add water to the full pot mark, and mix the citric acid and water well.
5. Mix well, close the lid, immediately connect the
plug, press , and set to "Cleaning".
Cleaning start
The liquid crystal display will rotate and indicate cleaning.
Select
¥ Cleaning time
About 50 minutes
Cleaning completion
Cleaning completion is announced by the buzzer and by
indication.
Simultaneous flashing
eboil
The citric acid is available from an authorized dealer.
(
Model No:SAN-80N
* Follow the directions for cleaning printed on the citric acid container.
* Since the citric acid used for cleaning is a food additive, it is harmless to humans.
Caution:
¥
Do not clean with citric acid while the charcoal filter is installed.
(The citric acid will dissolve the coral sand to smaller particles and the water will become cloudy.)
If cleaning with citric acid has been done: Replace the charcoal filter. ( P. 32)
¥ To remove any discoloration from the area above the full pot mark, rub the inside lightly with a wet sponge.
¥ If the discoloration cannot be removed by rubbing, clean the pot several times using citric acid.
Dechlorination
Long Boil Cleaning
Temp.
h
Buzzer sound
)
6. Remove the power cord and the lid, and drain the
hot water until you can see the drain mark.
7. Boil a fresh pot of water as usual, to remove any
residual smell of citric acid. Then, discard the water.
¥ After completion of the cleaning, install the charcoal filter.
26
Page 27
Select
"Cleaning"
Select
"Cleaning"
SAN-80N
SAN-80N
27
Page 28
Q&A
QUESTION
Incrustations?
¥ What is the white or glittering
matter suspended in the water?
¥ What is the rough, milky-white
matter deposited on the inner
¥ Has the fluororesin peeled?
ANSWER
This are minerals in the water, and they are called incrustations.
In case of water with a large mineral content (mineral water or ion
-adjusted water), incrustations may form on the inner container or
may be suspended in the water.
Incrustation examples:
¥Rough milky-white deposits (from calcium)
¥Milky-white or glittering suspensions (mineral crystals)
¥
Brown, gray, green, or other discolorations (caused by metal ions)
Incrustations have come loose.
* This is discoloration or corrosion of the inner container itself, not
The boiling sound seems to have
become louder.
Wash with citric acid
(
28
The boiling sound becomes louder when incrustations have formed.
)
P. 26
27
27
Page 29
Q&A
QUESTION ANSWER
Hot water does not
smoothly.
¥Wash the filter with a brush. ( P. 24)
¥If the scale cannot be removed,
replace the filter. ( P. 32)
flow out
25
25
After boiling, bubbles may form for a time and make it difficult to dispense the hot water.
32
32
The smell of incrustations?
There seems to be the smell of
chlorine.
Reboil ReboilReboil
Press to display .(P. 16
There seems to be the smell of
chlorine.
Long Boil Long Boil Long Boil
Depending on the amount of the chlorine in your tap water, the
water may have an odor.
)
The purification filter looses its effectiveness when it is
used for more than 6 months.
¥
Dispense after opening and closing the cover once.
(
Be careful of the steam when opening the cover.
17
17
)
Replace the purification filter once 6months.(P. 32
Hot water smells bad.
)
When you use the unit for the first time, you may smell resin or other materials.
However, after using the unit a few times, the smell will disappear.
If the unit is used while sitting on a rug or on a linoleum floor, the hot
water may pick
up a smell from the floor materials.
32 32
29
Page 30
Many symptoms are not actually problems with the unit that would require
Troubleshooting
repair. Check the following before calling us or asking for repairs.
Symptom Cause Remedy
Hot water does
not flow out.
Hot water flows
out by itself.
The water is not
boiled.
The temperature
indication on the
liquid crystal
display changes
widely up or down.
When the lid is
opened and closed,
a clattering sound
can be heard.
Lock
Unlock
Lock
Unlock
Lock
Unlock
●
Has the automatic lock been engaged?
●
Has water been added beyond the full pot mark?●Lower the water level.
●
Has the plug been disconnected?
●
The temperature indication can change widely when the plug is pulled during
●
Press the key.
●
Connect the plug.
heating.
●
This is the sound of the valve operating to prevent the outflow of hot water if the
jar pot should be toppled, and it is not a malfunction.
The outside of the
main unit is hot.
30
●
Since the unit keeps water warm at a high temperature, if the room temperature is
very high, the outside of the main unit may reach about 55¡C. This is normal.
Page 31
Symptom Cause Remedy
The buzzer beeps
"beep beep, beep
beep", the lamps
flash , and
●
The function for preventing an empty container from
being heated has been activated.
●
Fill in water to the position
or higher and press "Reheating".
Reboil
Reboil
Reboil
" "is indicated.
●
The indicator lamps may flash alternately
●
Press the .
Reboil
when water is being added, depending on
the way the water is supplied.
Reboil
Reboil
●
When the container is cleaned with citric
acid, has citric acid built up on the bottom?
●
Disconnect the plug, and stir the
citric acid well to disperse it.
Then, clean the container.
The lamps flash
●
The sensor is defective. Please contact the shop where you bought the jar pot.
alternately and
is indicated.
●
When problems cannot be resolved using the suggestions mentioned above or when you think something is strange,
disconnect the plug from the unit. Wait at least 10 seconds and then reconnect it. Then, try operating the unit again.
●
Although the semi-transparent part of the inside of the lid may become yellowish, it does not present a problem in using the unit.
●
Since fluorine insulation is applied all the way down to or near the bottom of the container, the surface may be gritty and the
color can be different from that on the side.
31
Page 32
Replacement of parts
Charcoal filter
Replace after 6 months (to maintain the purification effect)
Filter
If the filter has been washed with a brush but scale cannot be removed,
replace it.
The filter can be removed by pulling firmly on it.
(
It is secured in place with a magnet.
Rubber seal
If the seal has lost its flexibility or if steam is leaking from a space between the lid and the pot due to cracks in the seal, replace it.
)
Sealing packing A
Set the packing groove onto the lid cover.
Seal packing B
1
Install with the packing holes matched to the screw holes of the lid.
2
Place the lid cover on top and tighten it with the screws.
1
1
2
2
Consumable parts are available from an authorized dealer.
Part name
Rubber packing set
Filter
Charcoal filter
(
for the circulation type
)
32
Part No.
APH65-313-0S
APB96-364-0U
NC-JD40N: APC58H442-0U
NC-JD40C: APC58P443-0U
*
Please buy as service parts(repair parts).
Page 33
Specifications
Model No.
Power supply
Power
consumption
Dimensions (approx.) (HxWxD)
When the handle is tilted
Electric pump (power consumption/rated time)
Excessive temperature rise prevention device
* The values in the parentheses indicate the keep-warm electric power consumption per hour (full pot/room temperature: 20°C)
* With use over a long time, the quantity which can be discharged in cordless operation will decrease (about one half after 5 years).
* Empty the container when you will not use the unit for the winter. Water left in the container may freeze, and the parts may be damaged.
When boiling water
Keep warm at 98
Keep warm at 85
Keep warm at 60
Weight (approx.)
Rated capacity
NC-JD40N/JD40C
Local voltage
850 W
75W(about 54Wh
75W(about 42Wh
75W(about 25Wh
28.5 23.0 32.0 cm
2.8 k
4.0 L
1.5 W/21 minutes
Thermal fuse
)
)
)
NC-JD40N/JD40C
850
54
42
25
28.5 23.0 32.0
NC-JD40N/-JD40C
850
54
42
25
28.5 23.0 32.0
33
Page 34
Page 35
Page 36
日本国・大阪
日本制造
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
Printed in Japan
PZ05H4421
M0901-2093
Loading...