Please use this Manual together with the Service Manual Order No. PAPTH141101CE
WARNING
The service information is designed for experienced repair technicians only and is not designed for use by the general
public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting
to service a product. Products powered by electricity should be serviced or repaired only by experienced professional
technicians. Any attempt to service or repair the product or products dealt within this service information by anyone
else could result in serious injury or death.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential that
these critical parts should be replaced with manufacturer’s specifi ed parts to prevent shock, fi re or other hazards. Do
not modify the original design without permission of manufacturer.
CodeWWLW
Power cord unitS3S3S3
Rate voltage and Frequency 220 ~ 240V/50Hz220V/60Hz
Rate Power Consumption
Power Consumption
Standard CapacityWash15.0 Kg15.0 Kg16.0 Kg15.0 Kg
Standard Consumption Water96 Liter96 Liter99 Liter96 Liter
Product WeightAccessories48 Kg48 Kg49 Kg48 Kg
Outer Dimention (mm.)
(WxDxH)
Pulsator with rated load (r.p.m.)95 r / min
Spin Tub with rated load (r.p.m.)630 r / min
Water Supply Pressure0.01 to 1 MPa (0.1 to 10 Kgf / cm
MotorSingle-phase induction motor 135°C
Safety SwitchChecking Unbalance
MR sensorOpenlid detection during operation
BuzzerRings when fi nishing washing or unusual
Detergent Case DispenserUsable
Fabric Softener DispenserUsable
Filter UnitUsable
Child SafetyUsable
Auto RestartUsable
Auto Power OffUsable
NORMAL15.0 kg16.0 kg
ENERGY SAVE (SPEEDY)15.0 kg16.0 kg
WETER SAVE15.0 kg16.0 kg
BABY-CARE (FOR MID-EAST)15.0 kgFRAGRANCE15.0 kg16.0 kg
COMFORTER4.2 kg4.2 kg
POWER WASH + SOAK15.0 kg16.0 kg
TUB HYGIENE-GENTLE HAND WASH2.5 kg2.5 kg
AIR DRY3.0 kg3.0 kg
Note : -Normal course and Water Save course are recommended for a normally soiled load at the rated capacity of this
washing machine.
NA-F150A3NA-FS16X3
MAXIMUM CAPACITY
Standard Water Supply : Middle East
FOR NA-F150A3
PROGRAM
NORMAL60 min12 minRefill 2 times5 min
ENERGY SAVE (SPEEDY)55 min9 minRefill 2 times5 min
WATER SAVE80 min12 min3 times5 min
BABY-CARE
FRAGRANCE85 min12 min2 times5 min
BLANKET75 min12 minRefill 2 times3 min
POWER WASH + SOAK120 min
GENTLE HAND WASH45 min12 minRefill 2 times1 min
TUB HYGIENE150 min
TOTAL TIME
(APPROX.)
75 min12 minRefill 2 times7 min
WASHRINSESPIN
(Soak 60min)+12 min
(Soak 60min)+12 min
Refill 2 times5 min
Refill 2 times7 min
Standard Water Supply : Saudi Arabia
FOR NA-FS16X3
PROGRAM
NORMAL60 min12 minRefill 2 times5 min
ENERGY SAVE (SPEEDY)55 min9 minRefill 2 times5 min
GENTLE HAND WASH45 min12 minRefill 2 times1 min
FRAGRANCE85 min12 min2 times5 min
BLANKET 80 min12 minRefill 2 times3 min
POWER WASH + SOAK130 min
WATER SAVE80 min12 min3 times5 min
TUB HYGIENE150 min
FOR NA-FS16X3
PROGRAM
NORMAL60 min12 minRefill 2 times5 min
ENERGY SAVE (SPEEDY)55 min9 minRefill 2 times5 min
GENTLE HAND WASH45 min12 minRefill 2 times1 min
FRAGRANCE85 min12 min2 times5 min
BLANKET 75 min12 minRefill 2 times3 min
POWER WASH + SOAK130 min
WATER SAVE80 min12 min3 times5 min
TUB HYGIENE150 min
Note : -Total time is approximate (When the standard water supply rate is 15 L / min).
-Total time may increase depending on low water pressure, bad draining conditions, and the amount and type of clothes.
TOTAL TIME
(APPROX.)
TOTAL TIME
(APPROX.)
WASHRINSESPIN
(Soak 70min)+12 min
(Soak 60min)+12 min
WASHRINSESPIN
(Soak 70min)+12 min
(Soak 60min)+12 min
Refill 2 times5 min
Refill 2 times7 min
Refill 2 times5 min
Refill 2 times7 min
- 4 -
Page 5
INSTALLATION
1. Check the location.
■
Avoid the following locations for installation.
Locations with a possibility of freezing
•
Damp locations or locations where it may be
•
exposed to rain, etc.
(To prevent electric shock or fi re)
Locations exposed to direct sunlight
•
(To prevent malfunction or deformation)
Uneven or unstable locations (on blocks,
•
timbers, a table with wheels, etc.)
2. Attach the bottom cover.
Insert the bottom
cover along the
guides.
Fix with 2 screws.
COLD
HOT
Water supply hose
Bottom coverDrain hose
Water tap adaptor
Water tap adaptor
Elbow
A
B
Saudi Arabia Model
Water supply valve screw
Elbow
COLDHOT
Holes for the hose
holder
Holes for the hose
holder
Water supply
valve screw
Screw
3. Attach the external drain water hose.
Connect.
Hook the elbow of the drain hose
to the basin.
CAUTION
Make sure the drain hose is
Insert all the way.
Slide the hose band in the
arrow direction.
●Slide all the way until it stops.
securely hooked so that it does
not come off by water pressure
during drainage.
NOTE
●Do not twist, pull out or bend
the drain hose.
●Do not put the hose tip under
water.
●Do not direct the drain hose
downwards.
Water supply hose
Bottom coverDrain hose
A
B
Middle East Model
80 - 120 cm
Hose band
- 5 -
Page 6
4. Connect the water tap adaptor and water supply hose.
Connect the water tap adaptor to
Water faucet
Water tap adaptor
Water supply hose
CAUTION
●Tighten the nut fi rmly.
●Do not twist, squash, modify
or cut the hose.
the water faucet.
Turn part A to the left until approx.
1
4 mm of the thread becomes
visible.
Loosen the 4 screws.
2
Connect to the faucet and tighten
3
the screws.
Turn part A to the right and tighten
4
securely. (To prevent water
leakage)
Connect the water supply hose to
the water tap adaptor.
Insert the hose into the adaptor while
pushing down the lever, and hook
the claw of the lever on the fl ange of
the adaptor.
Connect the water supply hose to
the water supply valve screw.
Screw
Part A
Flange
Thread
Claw
Lever
For Middle East
Nut
Elbow
Hold the elbow and tighten the nut.
For Saudi Arabia
Water supply valve screw
COLD HOT
Nut
Elbow
Water supply hose
1
Check that the elbow is not loose.
2
CAUTION
●Do not make wrong connection
for the HOT and COLD water
supply faucets.
●Tighten the nut fi rmly.
●Do not twist, squash, modify or
cut the hose.
5. Connect the power plug and grounding wire.
●Ask a service person to do the grounding work.
●In case of a 2-pin power cord, establish a ground.
6. Check the washing machine is level.
■
The bubble should be at the
centre of the mark.
Mark
Bubble
If the bubble is out of the mark
Water supply
valve screw
Water supply hose
Turn the adjustable leg knob to
1
the left to loosen.
Leveller
Turn the adjustable
2
leg to eliminate
wobble.
Perform a trial operation.
●Check that there is no water leakage, abnormal sounds or error display.
- 6 -
Turn to the right to
3
tighten.
To lowerTo raise
Page 7
OPERATION PANEL / MIDDLE EAST
NA-F150A3
Change water
level
During the wash
process, press “Water
Level” to change the
water level.
●Some water levels
cannot be selected
depending on the
program.
●When the remaining
time is displayed,
press “Water Level”
to check the water
level.
Water level/remaining
time
After starting operation, indicates
the water level according to the
amount of laundry.
After approx. 5 seconds, indicates
the approximate remaining time
(min).
Water level/water amounts
Level
Detergent *
Water amount
(L)
* : 1 scoop of detergent
●Each water level, except “Extra Low”, has
three water amount options that can be
switched while the level is lit by pressing
“Water Level”.
High
10-8
96 88 81 74 66 59 52 46 38 33
Mid
7-5
Low
4-2
Extra
Low
1
Child Lock lamp
Change process
settings
Change the combination
of wash, rinse and spin
processes, and the time
length or number of times for
individual processes.
Lighted
Flashing (in progress)
●After starting operation,
you can change settings
only during wash process
by pressing “Start/Pause”.
Preset
Set the time to fi nish washing
(in hours). ( lights.)
e.g.) 8 hours later
●Setting range: 2 - 24
hours later, in one-hour
increments. (3 - 24 hours
later for the Power wash +
Soak program)
●Not available for the
following programs:
Gentle Hand Wash,
Fragrance, Blanket, Tub
Hygiene, Air Dry
Power Off/OnAir DryStart/Pause
Program selection
NOTE
●In case of a power failure during
operation, operation will resume from
the point where it was stopped when the
power is recovered (Auto Restart).
●The power turns off automatically if you
do not press “Start/Pause” within 10
minutes after power-on.
- 7 -
Page 8
OPERATIONS PANEL / SAUDI ARABIA
NA-FS16X3
Change water
level
During the wash
process, press “Water
Level” to change the
water level.
●Some water levels
cannot be selected
depending on the
program.
●Only during the wash
process, press “Water
Level” to check the
water level.
Water level/remaining time
After starting operation, indicates the
water level according to the amount
of laundry.
* : 1 scoop of detergent
After approx. 5 seconds, indicates the
approximate remaining time (min).
Water level/water amounts
Level
Detergent *
Water amount
(L)
●Each water level, except “Extra Low”, has
three water amount options that can be
switched while the level is lit by pressing
“Water Level”.
High
10-8
99 88 81 74 66 59 52 46 38 33
Mid
7-5
ECONAVI lamp (P. 12)
Low
4-2
Extra
Low
1
Air Dry
Child Lock lamp
Start/PauseProgram selection
Power Off/On
Change process
Preset
Temp Setting
Set the time to fi nish washing
For washing, cold water can be mixed
with hot water. Press the button to select
Hot/Warm/Cold.
Do not use water hotter than 60 ºC.
● The estimated water temperature in
the tub during wash process (when
hot water is 50 ºC, and normal water
is 20 ºC):
Hotapprox. 40 ºC
Warmapprox. 30 ºC
● Lamp indications
Lighted: Hot/Warm/Cold is set.
Flashing: Hot water is being supplied.
● Not available for the following
programs: Gentle Hand Wash, Tub
Hygiene, Air Dry
■
Touch operation
●Operation buttons are capacitive (Except for the power Off/On and Start/Pause buttons). Touch the buttons
directly with your bare fi ngers.
●When a towel containing water or detergent touches an operation button, the appliance may malfunction.
(in hours). ( lights.)
e.g.) 8 hours later
●Setting range: 2 - 24
hours later, in one-hour
increments. (3 - 24 hours
later for the Power wash +
Soak program)
●Not available for the
following programs:
Gentle Hand Wash,
Fragrance, Blanket, Tub
Hygiene, Air Dry
NOTE
●In case of a power failure during operation, operation will resume from the point where it was stopped when the
power is recovered (Auto Restart).
●The power turns off automatically if you do not press “Start/Pause” within 10 minutes after power-on.
- 8 -
Change the combination
of wash, rinse and spin
processes, and the time
length or number of times
for individual processes.
Flashing (in progress)
settings
Lighted
●After starting operation,
you can change settings
only during wash
process by pressing
“Start/Pause”.
Page 9
NA-F150A3
Change water
level
During the wash
process, press “Water
Level” to change the
water level.
●Some water levels
cannot be selected
depending on the
program.
●When the remaining
time is displayed,
press “Water Level”
to check the water
level.
Water level/remaining
time
After starting operation, indicates
the water level according to the
amount of laundry.
After approx. 5 seconds, indicates
the approximate remaining time
(min).
Water level/water amounts
Level
Detergent *
Water amount
(L)
* : 1 scoop of detergent
●Each water level, except “Extra Low”, has
three water amount options that can be
switched while the level is lit by pressing
“Water Level”.
High
10-8
96 88 81 74 66 59 52 46 38 33
Mid
7-5
Low
4-2
Extra
Low
1
Power Off/OnAir DryStart/PauseProgram selectionChild Lock lamp
Change process
settings
Change the combination
of wash, rinse and spin
processes, and the time
length or number of times for
individual processes.
Lighted
Flashing (in progress)
●After starting operation,
you can change settings
only during wash process
by pressing “Start/Pause”.
Set the time to fi nish washing
(in hours). (
●Setting range: 2 - 24
hours later, in one-hour
increments. (3 - 24 hours
later for the Power wash +
Soak program)
●Not available for the
following programs:
Gentle Hand Wash,
Fragrance, Blanket, Tub
Hygiene, Air Dry
Preset
lights.)
e.g.) 8 hours later
Temp Setting
For washing, cold water can be mixed
with hot water. Press the button to select
Hot/Warm/Cold.
Do not use water hotter than 60 ºC.
● The estimated water temperature in
the tub during wash process (when
hot water is 50 ºC, and normal water
is 20 ºC):
Hotapprox. 40 ºC
Warmapprox. 30 ºC
● Lamp indications
Lighted: Hot/Warm/Cold is set.
Flashing: Hot water is being supplied.
● Not available for the following
programs: Gentle Hand Wash, Tub
Hygiene, Air Dry
NOTE
●In case of a power failure during operation, operation will resume from the point where it was stopped when the
power is recovered (Auto Restart).
●The power turns off automatically if you do not press “Start/Pause” within 10 minutes after power-on.
- 9 -
Page 10
WASHING / MIDDLE EAST
Preparation:
●Check if the washing machine is properly installed.
●Turn on the water faucet.
1
2
3
4
Timer preset
After loading laundry
Turn the power on.
●The Normal program is selected when the
power is turned on.
Select a program.
■
Timer preset
Start.
The pulsator moves without
water and measures the amount
of laundry (approx. 5 seconds).
Water level indication
(approx. 5 seconds)
Remaining time indication
●To check the water level
Press “Water Level”.
According to the water level indication
Put in detergent.
●Approx. 20 seconds after the water level is
displayed, water supply begins.
3
Set how many hours later to finish
operation.
When the Fragrance program is selected
2
●2 minutes after start-up, all indications except
turn off.
●To confirm after the timer has been set, press
.
●To cancel or change, press .
●The hours that can be set differ depending on
the program.
The buzzer sounds before the final rinse and
operation is paused. Put the desired amount
of softener which has been diluted with water
directly into the tub.
5 beeps
1
5
Close the lid.
Operation ends with beeps.
- 10 -
●The Fragrance program cannot be selected
when Child Lock is set.
●Operation will resume if the lid is left closed for
more than 1 hour.
■
After pressing “Start”
●You can change the water level until the end of
the wash process.
●You can change each of the “Wash”, “Rinse”
and “Spin” operation contents until the end of
the wash process. Press “Pause” beforehand.
●You cannot change the program.
Page 11
WASHING / SAUDI ARABIA
Preparation:
●Check if the washing machine is properly installed.
●Turn on the water faucet.
●When using Temp Setting, turn on both hot and cold water faucets.
Temp setting
Timer preset
After loading laundry
1
●The Normal program is selected when the
Select a program.
2
3
According to the water level indication
Put in detergent.
4
●Approx. 20 seconds after the water level is
Turn the power on.
power is turned on.
■
Temp Setting
■
Timer preset
Start.
The pulsator moves without
water and measures the
amount of laundry
(approx. 10 seconds).
Water level indication
(approx. 5 seconds)
Remaining time indication
●To check the water level
→
Press “Water Level”.
displayed, water supply begins.
23
Press to select Hot/Warm/Cold for
washing.
Hot ← Warm ← Cold
Set how many hours later to fi nish
operation.
●2 minutes after start-up, all indications except
turn off.
●To confirm after the timer has been set, press
.
●To cancel or change, press .
●The hours that can be set differ depending on
the program.
When the Fragrance program is selected
The buzzer sounds before the final rinse and
operation is paused. Put the desired amount
of softener which has been diluted with water
directly into the tub.
5 beeps
1
5
Close the lid.
Operation ends with beeps.
- 11 -
●The Fragrance program cannot be selected
when Child Lock is set.
●Operation will resume if the lid is left closed for
more than 1 hour.
■
After pressing “Start”
●You can change the water level until the end of
the wash process.
●You can change each of the “Wash”, “Rinse”
and “Spin” operation contents until the end of
the wash process. Press “Pause” beforehand.
●You cannot change the program.
Page 12
WIRING OPTIONS
Blanket
■
Washable blankets
Material: 100 % synthetic fi bre or 100 % cotton
•
Weight: 4.2 kg or less
•
Blankets with a machine-washable tag attached
•
●Put a blanket in the net and load it in the tub.
Roll
NOTE
●Use liquid detergent.
●The water level indication shows the maximum and
cannot be changed.
ECONAVI
●The zipper part
should face up.
(To prevent
damage to the
net)
Gentle Hand Wash
Use this program to gently wash delicate clothes and
stylish garments.
Attach the washing board.
Double up the
1)
board and put it
in the base.
Align the
2)
position
and open
the board.
Available in the Normal program, this function
automatically adjusts the operation time and water
level according to the detected amount of laundry
and water temperature.
ECONAVI will not work if you change the water
level or process settings.
■
Lamp indications
Flashing: Detecting
•
Lighted: ECONAVI enabled
•
Unlit: ECONAVI disabled
•
■
Switch on/off
1
2
3
4
5
* Test conditions:
• Normal program
• Comparison between ECONAVI-enabled operation (amount
of laundry: 4.0 kg, water temperature: above 35 ºC) and
ECONAVI-disabled operation (amount of laundry: 16.0 kg
(rated capacity), water temperature: below 15 ºC)
• Test was conducted based on IEC60456 except for water
temperature.
Press and hold for 3 seconds
to select (On) or (Off)
6 beeps
Press the board circumference and fi x it.
3)
●Set the claws (4 places) securely.
Load the laundry.
Load laundry evenly.
●Load lighter items fi rst and press
them from above.
●Use laundry nets for delicate
underwear only.
●Amount that can be washed at
one time:
Water Level
46 L2.5 k
38 L1.2 k
NOTE
●Do not use bleach.
●Use liquid delicate detergent.
●After operation ends, take out clothes immediately.
(To prevent wrinkles and colour staining)
Capacity
g
g
- 12 -
Page 13
WIRING DIAGRAM
1$)6;
1$)$
- 13 -
Page 14
PARTS EXPLODED VIEW AND REPLACEMENT PARTS LIST
Parts Explode View : A
A22
A23
A2
A3
A5.1
A4
A10
A4
A6
A2.1
A8
A9
A7
A7
A6
A5
A17
A18
A13
A12
A14
A24
A1
A11
A10
A19
A20
A16
A15
A21
- 14 -
Page 15
Replacement Parts List
Part List - Part A
Ref.
Safety
No.
BODY BAXW01028XT0W
A1
PANEL FACE BAXW01469VY00
A2
A2.1 PANEL FACE FAXW01509MG00
A3PANEL FACE DAXW01488XT10
A4PANEL FACE EAXW01498XT10
A5PANEL FACE A UNITAXW001J9VW00
A5.1 PANEL FACE CAXW01478XT00
A6CONTROLLER UNITAXW024C9VY06
A7INSULATION SPACER AAXW04868XT00
A8PANEL AAXW01308XT0W
A9LOCATING INSTRUCTION DAXW99629VY00
A10 LID HINGE SPRINGAXW11168XT00
A11 LEVELLERAXW03536NA10
A12 SOAP CASE BAXW21518XT1W
A13 ANTIFREEZE INSTRUCTION B AXW99599CR0W
A14 SOAP CASE LIDAXW21928XT0W
A15 PANEL A BACK COVERAXW01388XT10
A16 SOAP CASE PACKINGAXW21647EC00
A17 PRESSURE SENSOR UNITAXW024T04400
A18 SUB DRAIN HOSE UNITAXW002Q9MG00
A19 SAFETY SWITCH A AXW166125000
A20 FEEDING VALVEAXW292126716
A21 CONNECTOR LEAD WIRE
UNIT
A22 LID UNITAXW001G8XT0W
A23 LID HINGE SHAFTAXW01937JS00
A24 SENSOR UNITAXW024N09410
A25 FEEDING VALVEAXW292126606
Part Name Part No.
AXW01029PN0L
AXW01029PN0W
AXW01469VW00
AXW01469VX00
AXW01499MG10
AXW024C9VW04
AXW024C9VX04
AXW04869MG00
AXW01309MG0L
AXW99629VW00
AXW11168XT50
AXW21518XT1L
AXW99599CR0L
AXW21928XT0L
AXW01389PN00
AXW21647EC00
AXW014A9PG10
AXW014A9VW00
AXW014A9PP10
AXW001G8XT0L
UAE(EXP)KuwaitSaudi Arabia
F150A3F150A3FS16X3F150A3
11
1
1
11
1
1
1
111
111
1
1
111
11
1
1
111
1
111
1
11
11
1111
1111
1111
111
1
111
1
111
1
11
11
2222
11
1111
1111
1111
1111
11
1
1
111
1
2222
1111
11
Remark
WHITE
WHITE/HOT WATER
STAINLESS COLOUR/HOT WATER
ENGLISH/ARABIC
ENGLISH/ARABIC
ENGLISH/ARABIC
FOR X3 SERIES
FOR A3 SERIES
ECONAVI
WHITE
STAINLESS COLOUR
ARABIC
ARABIC/HOT WATER
RIGHT
LEFT
WHITE
STAINLESS COLOUR
ARABIC/WHITE
ARABIC/STAINLESS COLOUR
WHITE
STAINLESS COLOUR
COLD WATER
HOT WATER
COLD WATER
A3 SERIES
A3 SERIES/HOT WATER
X3 SERIES/HOT WATER
WHITE
STAINLESS COLOUR
BODY B
HOT WATER
Safety
Screws
Ref.
No.
SPECIAL TAPPING SCREWXTWAXW469J
BINDING TAPPING SCREW
Part Name Part No.
XTB4+12CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
XTWAXW435
UAE(EXP)KuwaitSaudi Arabia
F150A3F150A3FS16X3F150A3
4444
4444
6676
2222
4444
6666
2222
22
- 15 -
Remark
BODY B~BODY AU
LID UNIT
CONTROLLER HOLDER~PANEL A
PANEL A BACK COVER~SAFETY SW.
PANEL A~BODY B
PANEL A BACK COVER~BODY B
PANEL A BACK COVER~FEEDING VALVE
FEEDING VALVE HOT WATER
Page 16
Parts Explode View : Part B
B2
B23
B19
B1
B20
B22
B24
B19
B21
B20
B21
B17
(FOR NA-F150A3)
B18
B13
B2
(FOR NA-FS16X3)
B8
B9
B12
B11
B10
B14
B4
B26
B3
Accessories
B4
B24
B5
B25
B15
B16
B4
B7B6
- 16 -
Page 17
Replacement Parts List
Part List - Part B
Ref.
Safety
No.
B1 BODY A UNITAXW001A8XT2W111WHITE
B2 GRIPAXW01107JP1W111WHITE
B3 BASE AAX’W03019VY001111
B4 LEG COVERINGAXW03397JS001111
B5 ADJUSTABLE LEG UNITAXW003D8XT001111
SERVICE PRESSURE HOSE UNIT
B6
B7 BOTTOM COVERAXW21588XT001111
B8 BACK PANELAXW01568XT201111
B9 POWER CORD UNIT -S3AXW004A772E41111
B10 COIL BOXAXW45519MG001
B11 COIL UNITAXW034L9MG061
B12 NOISE REDUCERAXW2430049001
B13 COIL BOX PLATEAXW45529MG001
B14 CHEMICAL COVERAXW04487EC10111
B15 FLEXIBLE HOSE A UNITAXW002D6RJ001111
B16 HOSE BANDAXW02456RJ101111
B17 CAPACITORAXW04037V8071114F
B18 NAME PLATEAXW01539VY0011
B19 BODY A PROTECTIONAXW90468AR104444t30x50x50/HARD TYPE
B20 BODY A PROTECTIONAXW90468XT502232t20x50x50/SOFT TYPE