Panasonic MC-E591, MC-E590, MC-E593 User Manual

Operating Instructions
Vacuum Cleaner MC-E590, MC-E591, MC-E593
We would recommend that you read these Operating Instructions before attempting to operate the unit and that you note the Important Safety Instructions. Please keep in a safe place with your Authorised Dealer Service booklet. This product complies with the directives 73/23/EEC and 89/336/EEC.
www.panasonic.co.uk
(for customers in the UK only)
Shop
@
– 2 –
TABLE OF CONTENTS
Page
• Caution for AC Mains Lead (UK, IRL only) 2
• Important Safety Instructions for the user 3
• Cautions 3
• Identification of main parts 4 HOW TO ASSEMBLE / OPERATE YOUR CLEANER A) Handle assembly 5 B) Power cord release / storage 5 C) Dust compartment operation 6 D) ON/OFF Switch / Variable power control 6 E) Dust sensor (MC-E593 only) 7 F) Foot pedal body adjustment / Automatic 7
beater bar ON/OFF
Page
G) Floor Scratch prevention 8 H) How to use the accessories 8
MAINTENANCE AND SERVICING
• How to empty the dust compartment 9
• Filter care 10
• Blockages 11
• Maintenance for the beater bar 12
• Protection features 12
• Trouble shooting guide 13
• Specifications 14
• Consumables / Accessories 15
CAUTION FOR AC MAINS LEAD (UK, IRL only)
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has rating of 13 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS ADANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral
Brown : Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol
How to replace the Fuse:
There are two types of the supplied AC Mains Lead : A and B as shown below. 1 Open the fuse compartment with a screwdriver. 2 Replace the fuse and fuse cover if detachable.
TYPE A TYPE B
!
3
CAUTIONS
4) To avoid damaging the machine, never let the vacuum cleaner pick up wet matter, mud, burning ashes or large and sharp objects.
6) To avoid injury, keep your fingers and hands away from the beater bar and never put them between the body parts.
1. To avoid any possible damage to the power supply cord, never run over the power supply cord or a ll ow it to become caught in the beater bar when using the vacuum cleaner.
2. Do not run the vacuum cleaner over tassels or fringes of rugs or mats as they could get caught up in the beater bar and may cause damage to the beater bar motor.
3. Keep the vacuum cleaner away from heat sources such as radiators, fires, direct sunlight, etc.
5. Do not pull on the power supply cord when disconnecting the appliance from the mains, always pull on the plug body itself.
IMPORTANT SAFETY INSTRUCTIONS FOR THE USER
When using this vacuum cleaner, please observe these basic precautions. WARNING: To reduce the risk of fire, electric shock, or injury:
Do not leave the vacuum cleaner plugged in to mains socket. Unplug from the socket when not in use
and before cleaning the appliance or undertaking maintenance operations.
Electric shocks can occur if used outdoors or on wet surfaces.
This appliance is not intended for use by young children or infirm people without supervision; young children
should be supervised to ensure that they do not play with the appliance.
Do not use with damaged power supply cord or plug. If the vacuum cleaner is not working as it should be, or has been
dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre.
Do not pull or carry by the power supply cord, use power supply cord as a handle, close a door on power
supply cord, pull power supply cord around sharp edges or corners. Do not run vacuum cleaner over the power supply cord. Keep power supply cord away from heated surfaces.
Do not handle plug or vacuum cleaner with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and
anything that may block or reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Do not use without filters and / or dust compartment in place.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible materials, or others that may become so, or use in areas where
they may be present.
This appliance should be serviced by an authorised Panasonic Service Centre, and only genuine
Panasonic spare parts should be used.
Keep feet, fingers and hands away from the beater bar. (It may cause injury).
!
NOTE: These vacuum cleaners are designed for general household use only and are not suitable for use in a garage or to suck up liquids.
!
4
IDENTIFICATION OF MAIN PARTS
M
A
X
B) Power supply
cord clip
Maximum dust level
mark
Exhaust cover / Clean air filter
Release handle
Furniture guard
Cleaning head
A-1) Handle
A-3) Hose clip
G) Hose support
E-2) Foot pedal
G) Dusting brush
C) ON/OFF Switch and
Variable power control (MC-E590 ON/OFF Switch only)
D) Dust sensor indicator
(MC-E593 only)
E) ON/OFF
Beater bar pedal
Carrying handle
G) Upholstery nozzle
Hose
G) Crevice nozzle
E) Reset button
B) Power supply cord
(Mains Lead)
B-2) Power supply cord
rewind button (except MC-E590)
G) Connection pipe
G) Extension wand
Dust
compartment
B-1) Upper cord hook
(MC-E590 only)
B-1) Lower cord hook
(MC-E590 only)
– 5 –
A) HANDLE ASSEMBLY
1) Remove the dusting brush from the handle and line the handle up with the body of the cleaner in the correct position as shown in the illustration. NOTE: Remove the handle screw from the body first.
3) Re-install the dusting brush in its storage position. Place the hose around the hose clip and push inwards to secure. NOTE: Always place the hose in a clockwise direction.
HOW TO ASSEMBLE / OPERATE YOUR CLEANER
B) POWER CORD RELEASE / STORAGE
3) To release the power supply cord, pull it out by hand and fix it onto the cord clip in order to help secure it during use. NOTE: When in use it is advisable to pull out the full length of the power supply cord.
4) To rewind the power supply cord, press and hold the rewind button, allowing the power supply cord to be automatically rewound into the cleaner. IMPORTANT: When rewinding the power supply cord, keep the cord/plug in one hand to avoid damaging the cleaner.
NOTE: To avoid any possible damage to the power supply cord, never run over the cord or allow it to become caught in the beater bar.
Hose clip
2) Insert the base of the handle into the top of the body of the cleaner as shown. Push in the handle and tighten the screw. IMPORTANT: Do not over tighten the screw.
Handle screw
Dusting brush
1) To store the power supply cord, turn the upper cord hook in to the upright position and wind the power supply cord around the upper and lower cord hooks.
2) To release the power supply cord for instant use, turn the upper cord hook. Then fix the power supply cord into the cord clip to help secure it during use.
MC-E590
MC-E591 / MC-593
Upper Cord hook
Lower Cord hook
Loading...
+ 11 hidden pages