Panasonic MALS068X User Manual
Zener Diodes
Publication date: April 2006 SKE00022CED
Features
Bi-directional and high electrostatic discharge ESD
Small terminal capacitance C
t
Absolute Maximum Ratings
a
= 25
= 25
Repetitive peak forward current
200
Total power dissipation
P
T
mW
Junction temperature
T
j
–55 to +150
Electrostatic discharge
ESD
kV
Note)
T
= 150 mW achieved with a printed circuit board.
2 : Test method: IEC61000-4-2
(C = 150 pF, R = 330
Electrical Characteristics
T
a
= 25
= 25
±
Typ
Zener voltage
V
= 5 mA
= 5 mA
V
Zener operating resistance
= 5 mA
= 5 mA
20
Ω
Reverse current
V
= 4.0 V
= 4.0 V
Terminal capacitance
t
V
= 0 V, f = 1 MHz
= 0 V, f = 1 MHz
pF
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.
2. The temperature must be controlled 25
C for V
mesurement.
V
Z
value measured at other temperature must be adjusted to V
Z
(25
C)
3.
Z
guaranted 20 ms after current fl ow.
Unit : mm
1 : Cathode
2 : Cathode
EIAJ : SC-79 SSMini2-F1 Package
0.80
+0.05
–0.03
0.60
+0.05
–0.03
0.12
+0.05
–0.02
1.20
+0.05
–0.03
0
+0
–0.05
0.30±0.05
0.01±0.01
1.60±0.05
0.01±0.01
1
2
0.80±0.05(0.80)
(0.60)
(0.15)
(0.60)
5°
5°
1
2
This product complies with the RoHS Directive (EU 2002/95/EC).
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.
Loading...